View PIC18F6390_2241296.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? 2004 microchip technology inc. preliminary ds39629b PIC18F6390/6490/8390/8490 data sheet 64/80-pin flash microcontrollers with lcd driver and nanowatt technology
ds39629b-page ii preliminary ? 2004 microchip technology inc. information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. it is your responsibility to ensure that your application m eets with your specifications. no representation or warranty is given and no liability is assumed by microchip technol ogy incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. use of mi crochip?s products as critical components in life support syst ems is not authorized except with express written approval by microchip. no licenses are conveyed, implicitly or ot herwise, under any intellectual property rights. trademarks the microchip name and logo, the microchip logo, accuron, dspic, k ee l oq , micro id , mplab, pic, picmicro, picstart, pro mate, powersmart, rfpic, and smartshunt are registered trademarks of micr ochip technology incorporated in the u.s.a. and other countries. amplab, filterlab, mxdev, mxlab, picmaster, seeval, smartsensor and the embedded control solutions company are registered trademarks of microchip technology incorporated in the u.s.a. analog-for-the-digital age, app lication maestro, dspicdem, dspicdem.net, dspicworks, ecan, economonitor, fansense, flexrom, fuzzylab, in-circuit serial programming, icsp, icepic, migratable memory, mpasm, mplib, mplink, mpsim, pickit, picdem, picdem.net, piclab, pictail, powercal, powerinfo, powermate, powertool, rflab, rfpicdem, select mode, smart serial, smarttel and total endurance ar e trademarks of microchip technology incorporated in the u.s.a. and other countries. sqtp is a service mark of mi crochip technology incorporated in the u.s.a. all other trademarks mentioned herein are property of their respective companies. ? 2004, microchip technology incorporated, printed in the u.s.a., all rights reserved. printed on recycled paper. note the following details of the code protection feature on microchip devices: microchip products meet the specification cont ained in their particular microchip data sheet. microchip believes that its family of products is one of the mo st secure families of its kind on the market today, when used i n the intended manner and under normal conditions. there are dishonest and possibly illegal methods used to breach the code protection feature. all of these methods, to our knowledge, require using the microchip produc ts in a manner outside the operating specif ications contained in microchip?s data sheets. most likely, the person doing so is engaged in theft of intellectual property. microchip is willing to work with the customer who is concerned about the integrity of their code. neither microchip nor any other semiconductor manufacturer c an guarantee the security of their code. code protection does not mean that we are guaranteeing the product as ?unbreakable.? code protection is constantly evolving. we at microchip are co mmitted to continuously improvi ng the code protection features of our products. attempts to break microchip?s c ode protection feature may be a violation of the digital millennium copyright act. if such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that act. microchip received iso/ts-16949:2002 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in chandler and tempe, arizona and mountain view, california in october 2003. the company?s quality system processes and procedures are for its picmicro ? 8-bit mcus, k ee l oq ? code hopping devices, serial eeproms, microperipherals, nonvolatile memory and analog products. in addition, microchip?s quality system for the design and manufacture of development systems is iso 9001:2000 certified.
? 2004 microchip technology inc. preliminary ds39629b-page 1 PIC18F6390/6490/8390/8490 lcd driver module features: direct driving of lcd panel up to 48 segments: software selectable programmable lcd timing module: - multiple lcd timing sources available - up to 4 commons: static, 1/2, 1/3 or 1/4 multiplex - static, 1/2 or 1/3 bias configuration can drive lcd panel while in sleep mode power managed modes: run: cpu on, peripherals on idle: cpu off, peripherals on sleep: cpu off, peripherals off idle mode currents down to 5.8 a typical sleep current down to 0.1 a typical timer1 oscillator: 1.8 a, 32 khz, 2v watchdog timer: 2.1 a two-speed oscillator start-up flexible oscillator structure: four crystal modes: - lp: up to 200 khz - xt: up to 4 mhz - hs: up to 40 mhz - hspll: 4-10 mhz (16-40 mhz internal) 4x phase lock loop (available for crystal and internal oscillators) two external rc modes, up to 4 mhz two external clock modes, up to 40 mhz internal oscillator block: - 8 user selectable frequencies, from 31 khz to 8 mhz - provides a complete range of clock speeds from 31 khz to 32 mhz when used with pll - user-tunable to compensate for frequency drift secondary oscillator using timer1 @ 32 khz fail-safe clock monitor: - allows for safe shut down of device if primary or secondary clock fails peripheral highlights: high current sink/source 25 ma/25 ma four external interrupts four input-change interrupts four 8-bit/16-bit timer/counter modules real-time clock (rtc) software module: - configurable 24-hour clock, calendar, automatic 100-year or 12800-year, day-of-week calculator - uses timer1 up to 2 capture/compare/pwm (ccp) modules master synchronous serial port (mssp) module supporting 3-wire spi? (all 4 modes) and i 2 c? master and slave modes addressable usart module: - supports rs-485 and rs-232 enhanced addressable usart module: - supports rs-485, rs-232 and lin 1.2 - auto-wake-up on start bit - auto-baud detect 10-bit, up to 12-channel analog-to-digital converter module (a/d): - auto-acquisition capability - conversion available during sleep dual analog comparators with input multiplexing special microcontroller features: c compiler optimized architecture - optional extended instruction set designed to optimize re-entrant code 1000 erase/write cycle flash program memory typical flash retention: 100 years typical priority levels for interrupts 8 x 8 single-cycle hardware multiplier extended watchdog timer (wdt): - programmable period from 4 ms to 132 s - 2% stability over v dd and temperature in-circuit serial programming? (icsp?) via two pins in-circuit debug (icd) via two pins wide operating voltage range: 2.0v to 5.5v device program memory data memory i/o lcd (pixel) 10-bit a/d (ch) ccp (pwm) mssp eusart/ ausart comparators timers 8/16-bit flash (bytes) # single-word instructions sram (bytes) spi master i 2 c? PIC18F6390 8k 4096 768 50 128 12 2 y y 1/1 2 1/3 pic18f6490 16k 8192 768 50 128 12 2 y y 1/1 2 1/3 pic18f8390 8k 4096 768 66 192 12 2 y y 1/1 2 1/3 pic18f8490 16k 8192 768 66 192 12 2 y y 1/1 2 1/3 64/80-pin flash microcontrol lers with lcd driver and nanowatt technology
PIC18F6390/6490/8390/8490 ds39629b-page 2 preliminary ? 2004 microchip technology inc. pin diagrams 64-pin tqfp note 1: re7 is the alternate pin for ccp2 multiplexing . PIC18F6390 1 2 3 4 5 6 7 8 9 10 11 12 13 14 38 37 36 35 34 33 50 49 17 18 19 20 21 22 23 24 25 26 lcdbias3 com0 re4/com1 re5/com2 re6/com3 re7/ccp2 (1) /seg31 rd0/seg0 v dd v ss rd1/seg1 rd2/seg2 rd3/seg3 rd4/seg4 rd5/seg5 rd6/seg6 rd7/seg7 lcdbias2 lcdbias1 rg0/seg30 rg1/tx2/ck2/seg29 rg2/rx2/dt2/seg28 rg3/seg27 mclr /v pp /rg5 rg4/seg26 v ss v dd rf7/ss /seg25 rf6/an11/seg24 rf5/an10/cv ref /seg23 rf4/an9/seg22 rf3/an8/seg21 rf2/an7/c1out/seg20 rb0/int0 rb1/int1/seg8 rb2/int2/seg9 rb3/int3/seg10 rb4/kbi0/seg11 rb5/kbi1 rb6/kbi2/pgc v ss osc2/clko/ra6 osc1/clki/ra7 v dd rb7/kbi3/pgd rc4/sdi/sda rc3/sck/scl rc2/ccp1/seg13 rf0/an5/seg18 rf1/an6/c2out/seg19 av dd av ss ra3/an3/v ref +/seg17 ra2/an2/v ref -/seg16 ra1/an1 ra0/an0 v ss v dd ra4/t0cki/seg14 ra5/an4/hlvdin/seg15 rc1/t1osi/ccp2 (1) rc0/t1oso/t13cki rc7/rx1/dt1 rc6/tx1/ck1 rc5/sdo/seg12 15 16 31 40 39 27 28 29 30 32 48 47 46 45 44 43 42 41 54 53 52 51 58 57 56 55 60 59 64 63 62 61 pic18f6490
? 2004 microchip technology inc. preliminary ds39629b-page 3 PIC18F6390/6490/8390/8490 pin diagrams (continued ) 80-pin tqfp note 1: re7 is the alternate pin for ccp2 multiplexing . pic18f8390 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 64 63 62 61 21 22 23 24 25 26 27 28 29 30 31 32 lcdbias3 com0 re4/com1 re5/com2 re6/com3 re7/ccp2 (1) /seg31 rd0/seg0 v dd v ss rd1/seg1 rd2/seg2 rd3/seg3 rd4/seg4 rd5/seg5 rd6/seg6 rd7/seg7 lcdbias2 lcdbias1 rg0/seg30 rg1/tx2/ck2/seg29 rg2/rx2/dt2/seg28 rg3/seg27 mclr /v pp /rg5 rg4/seg26 v ss v dd rf7/ss /seg25 rb0/int0 rb1/int1/seg8 rb2/int2/seg9 rb3/int3/seg10 rb4/kbi0/seg11 rb5/kbi1 rb6/kbi2/pgc v ss osc2/clko/ra6 osc1/clki/ra7 v dd rb7/kbi3/pgd rc4/sdi/sda rc3/sck/scl rc2/ccp1/seg13 rf0/an5/seg18 rf1/an6/c2out/seg19 av dd av ss ra3/an3/v ref +/seg17 ra2/an2/v ref -/seg16 ra1/an1 ra0/an0 v ss v dd ra4/t0cki/seg14 ra5/an4/hlvdin/seg15 rc1/t1osi/ccp2 (1) rc0/t1oso/t13cki rc7/rx1/dt1 rc6/tx1/ck1 rc5/sdo/seg12 rj0/seg32 rj1/seg33 rh1/seg46 rh0/seg47 1 2 rh2/seg45 rh3/seg44 17 18 rh7/seg43 rh6/seg42 rh5/seg41 rh4/seg40 rj5/seg38 rj4/seg39 37 rj7/seg36 rj6/seg37 50 49 rj2/seg34 rj3/seg35 19 20 33 34 35 36 38 58 57 56 55 54 53 52 51 60 59 68 67 66 65 72 71 70 69 74 73 78 77 76 75 79 80 rf5/an10/cv ref /seg23 rf4/an9/seg22 rf3/an8/seg21 rf2/an7/c1out/seg20 rf6/an11/seg24 pic18f8490
PIC18F6390/6490/8390/8490 ds39629b-page 4 preliminary ? 2004 microchip technology inc. table of contents 1.0 device overview ............................................................................................................. ............................................................. 7 2.0 oscillator configurations ................................................................................................... ......................................................... 31 3.0 power managed modes ......................................................................................................... .................................................... 41 4.0 reset ....................................................................................................................... ................................................................... 51 5.0 memory organization ......................................................................................................... ........................................................ 65 6.0 flash program memory........................................................................................................ ...................................................... 87 7.0 8 x 8 hardware multiplier................................................................................................... ......................................................... 91 8.0 interrupts .................................................................................................................. .................................................................. 93 9.0 i/o ports ................................................................................................................... ................................................................ 109 10.0 timer0 module .............................................................................................................. ........................................................... 131 11.0 timer1 module .............................................................................................................. ........................................................... 135 12.0 timer2 module .............................................................................................................. ........................................................... 141 13.0 timer3 module .............................................................................................................. ........................................................... 143 14.0 capture/compare/pwm (ccp) modules .......................................................................................... ....................................... 147 15.0 master synchronous serial port (mssp) module ............................................................................... ..................................... 157 16.0 enhanced universal synchronous asynchronous receiver transmitter (eusart) .................................................. ............. 197 17.0 addressable universal synchronous asynchr onous receiver transmitter (ausart) ............................................... ............ 217 18.0 10-bit analog-to-digital converter (a/d) module ............................................................................ ......................................... 231 19.0 comparator module.......................................................................................................... ........................................................ 241 20.0 comparator voltage reference module ........................................................................................ ........................................... 247 21.0 high/low-voltage detect (hlvd)............................................................................................. ................................................ 251 22.0 liquid crystal display (lcd) driver module ................................................................................. ............................................ 257 23.0 special features of the cpu ................................................................................................ .................................................... 281 24.0 instruction set summary .................................................................................................... ...................................................... 295 25.0 development support........................................................................................................ ....................................................... 345 26.0 electrical characteristics ................................................................................................. ......................................................... 351 27.0 dc and ac characteristics graphs and tables ................................................................................ ....................................... 387 28.0 packaging information...................................................................................................... ........................................................ 389 appendix a: revision history................................................................................................... .......................................................... 393 appendix b: device differences................................................................................................. ........................................................ 393 appendix c: conversion considerations .......................................................................................... ................................................. 394 appendix d: migration from baseline to enhanced devices........................................................................ ...................................... 394 appendix e: migration from mid-range to enhanced devices ....................................................................... ................................... 395 appendix f: migration from high-end to enhanced devices ........................................................................ ..................................... 395 index .......................................................................................................................... ........................................................................ 397 on-line support................................................................................................................ ................................................................. 407 systems information and upgrade hot line ....................................................................................... ............................................... 407 reader response ................................................................................................................ .............................................................. 408 PIC18F6390/6490/8390/8490 product identification system ........................................................................ .................................... 409
? 2004 microchip technology inc. preliminary ds39629b-page 5 PIC18F6390/6490/8390/8490 to our valued customers it is our intention to provide our valued customers with the best documentation possible to ensure successful use of your micro chip products. to this end, we will continue to improve our publications to better suit your needs. our publications will be refined and enhanced as new volumes and updates are introduced. if you have any questions or comments regar ding this publication, please contact the marketing communications department via e-mail at docerrors@mail.microchip.com or fax the reader response form in the back of this data sheet to (480) 792-4150. we welcome your feedback. most current data sheet to obtain the most up-to-date version of this data s heet, please register at our worldwide web site at: http://www.microchip.com you can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page . the last character of the literature number is the vers ion number, (e.g., ds30000a is version a of document ds30000). errata an errata sheet, describing minor operational differences fr om the data sheet and recommended workarounds, may exist for curren t devices. as device/doc umentation issues become known to us, we will publis h an errata sheet. the errata will specify the revisi on of silicon and revision of document to which it applies. to determine if an errata sheet exists for a particul ar device, please check with one of the following: microchip?s worldwide web site; http://www.microchip.com your local microchip sales office (see last page) the microchip corporate literatu re center; u.s. fax: (480) 792-7277 when contacting a sales office or the literature center, please specify which device, revision of silicon and data sheet (inclu de literature number) you are using. customer notification system register on our web site at www.microchip.com/cn to receive the most current information on all of our products.
PIC18F6390/6490/8390/8490 ds39629b-page 6 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 7 PIC18F6390/6490/8390/8490 1.0 device overview this document contains device specific information for the following devices: this family offers the advantages of all pic18 microcontrollers ? namely, high computational performance at an economical price. in addition to these features, the PIC18F6390/6490/8390/8490 family introduces design enhancements that make these microcontrollers a logical choice for many high-performance, power sensitive applications. 1.1 new core features 1.1.1 nanowatt technology all of the devices in the PIC18F6390/6490/8390/8490 family incorporate a range of features that can significantly reduce power consumption during operation. key items include: alternate run modes: by clocking the controller from the timer1 source or the internal oscillator block, power consumption during code execution can be reduced by as much as 90%. multiple idle modes: the controller can also run with its cpu core disabled, but the peripherals still active. in these states, power consumption can be reduced even further ? to as little as 4% of normal operation requirements. on-the-fly mode switching: the power managed modes are invoked by user code during operation, allowing the user to incorporate power-saving ideas into their application?s software design. lower consumption in key modules: the power requirements for both timer1 and the watchdog timer have been reduced by up to 80%, with typical values of 1.1 a and 2.1 a, respectively. 1.1.2 multiple oscillator options and features all of the devices in the PIC18F6390/6490/8390/8490 family offer nine different oscillator options, allowing users a wide range of choices in developing application hardware. these include: four crystal modes, using crystals or ceramic resonators. two external clock modes, offering the option of using two pins (oscillator input and a divide-by-4 clock output) or one pin (oscillator input, with the second pin reassigned as general i/o). two external rc oscillator modes, with the same pin options as the external clock modes. an internal oscillator block which provides an 8 mhz clock (2% accuracy) and an intrc source (approximately 31 khz, stable over temperature and v dd ), as well as a range of six user selectable clock frequencies between 125 khz to 4 mhz for a total of eight clock frequencies. this option frees the two oscillator pins for use as additional general purpose i/o. a phase lock loop (pll) frequency multiplier, available to both the high-speed crystal and internal oscillator modes, which allows clock speeds of up to 40 mhz. used with the internal oscillator, the pll gives users a complete selection of clock speeds from 31 khz to 32 mhz ? all without using an external crystal or clock circuit. besides its availability as a clock source, the internal oscillator block provides a stable reference source that gives the family additional features for robust operation: fail-safe clock monitor: this option constantly monitors the main clock source against a reference signal provided by the internal oscillator. if a clock failure occurs, the controller is switched to the internal oscillator block, allowing for continued low-speed operation or a safe application shutdown. two-speed start-up: this option allows the internal oscillator to serve as the clock source from power-on reset or wake-up from sleep mode until the primary clock source is available. PIC18F6390 pic18f8390 pic18f6490 pic18f8490
PIC18F6390/6490/8390/8490 ds39629b-page 8 preliminary ? 2004 microchip technology inc. 1.2 other special features memory endurance: the flash cells for program memory are rated to last for approximately a thousand erase/write cycles. data retention without refresh is conservatively estimated to be greater than 100 years. extended instruction set: the PIC18F6390/6490/8390/8490 family introduces an optional extension to the pic18 instruction set, which adds 8 new instructions and an indexed addressing mode. this extension, enabled as a device configuration option, has been specifically designed to optimize re-entrant application code originally developed in high-level languages such as c. enhanced addressable usart: this serial communication module is capable of standard rs-232 operation and provides support for the lin bus protocol. other enhancements include automatic baud rate detection and a 16-bit baud rate generator for improved resolution. when the microcontroller is using the internal oscillator block, the eusart provides stable operation for applications that talk to the outside world, without using an external crystal (or its accompanying power requirement). 10-bit a/d converter: this module incorporates programmable acquisition time, allowing for a channel to be selected and a conversion to be initiated without waiting for a sampling period and thus, reduces code overhead. extended watchdog timer (wdt): this enhanced version incorporates a 16-bit prescaler, allowing a time-out range from 4 ms to over 10 minutes that is stable across operating voltage and temperature. 1.3 details on individual family members devices in the PIC18F6390/6490/8390/8490 family are available in 64-pin (pic18f6x90) and 80-pin (pic18f8x90) packages. block diagrams for the two groups are shown in figure 1-1 and figure 1-2, respec- tively. the devices are differentiated from each other in three ways: 1. i/o ports: 7 bidirectional ports on 64-pin devices; 9 bidirectional ports on 80-pin devices. 2. lcd pixels: 128 (32 segs x 4 coms) pixels can be driven by 64-pin devices; 192 (48 segs x 4 coms) pixels can be driven by 80-pin devices. 3. flash program memory: 8 kbytes for pic18fx390 devices; 16 kbytes for pic18fx490. all other features for devices in this family are identical. these are summarized in table 1-1. the pinouts for all devices are listed in table 1-2 and table 1-3. like all microchip pic18 devices, members of the PIC18F6390/6490/8390/8490 family are available as both standard and low-voltage devices. standard devices with flash memory, designated with an ?f? in the part number (such as PIC18F6390), accommodate an operating v dd range of 4.2v to 5.5v. low-voltage parts, designated by ?lf? (such as pic18lf6490), function over an extended v dd range of 2.0v to 5.5v.
? 2004 microchip technology inc. preliminary ds39629b-page 9 PIC18F6390/6490/8390/8490 table 1-1: device features features PIC18F6390 pic18f6490 pic18f8390 pic18f8490 operating frequency dc ? 40 mhz dc ? 40 mhz dc ? 40 mhz dc ? 40 mhz program memory (bytes) 8k 16k 8k 16k program memory (instructions) 4096 8192 4096 8192 data memory (bytes) 768 768 768 768 interrupt sources 22 22 22 22 i/o ports ports a, b, c, d, e, f, g ports a, b, c, d, e, f, g ports a, b, c, d, e, f, g, h, j ports a, b, c, d, e, f, g, h, j number of pixels the lcd driver can drive 128 (32 segs x 4 coms) 128 (32 segs x 4 coms) 192 (48 segs x 4 coms) 192 (48 segs x 4 coms) timers 4444 capture/compare/pwm modules 2 2 2 2 serial communications mssp, ausart enhanced usart mssp, ausart enhanced usart mssp, ausart enhanced usart mssp, ausart enhanced usart 10-bit analog-to-digital module 12 input channels 12 input channels 12 input channels 12 input channels resets (and delays) por, bor, reset instruction, stack full, stack underflow (pwrt, ost), mclr (optional), wdt por, bor, reset instruction, stack full, stack underflow (pwrt, ost), mclr (optional), wdt por, bor, reset instruction, stack full, stack underflow (pwrt, ost), mclr (optional), wdt por, bor, reset instruction, stack full, stack underflow (pwrt, ost), mclr (optional), wdt programmable low-voltage detect yes yes yes yes programmable brown-out reset yes yes yes yes instruction set 75 instructions; 83 with extended instruction set enabled 75 instructions; 83 with extended instruction set enabled 75 instructions; 83 with extended instruction set enabled 75 instructions; 83 with extended instruction set enabled packages 64-pin tqfp 64-pin tqfp 80-pin tqfp 80-pin tqfp
PIC18F6390/6490/8390/8490 ds39629b-page 10 preliminary ? 2004 microchip technology inc. figure 1-1: pic18f6x90 ( 64-pin) block diagram instruction decode and control porta portb portc ra4/t0cki/seg14 ra5/an4/hlvdin/seg15 rb0/int0 rc0/t1oso/t13cki rc1/t1osi/ccp2 (1) rc2/ccp1 /seg13 rc3/sck/scl rc4/sdi/sda rc5/sdo /seg12 rc6/tx1/ck1 rc7/rx1/dt1 ra3/an3/v ref +/seg17 ra2/an2/v ref -/seg16 ra1/an1 ra0/an0 rb1/int1/seg8 data latch data memory (3.9 kbytes) address latch data address<12> 12 access bsr fsr0 fsr1 fsr2 inc/dec logic address 4 12 4 pch pcl pclath 8 31 level stack program counter prodl prodh 8 x 8 multiply 8 bitop 8 8 alu<8> address latch program memory (48/64 kbytes) data latch 20 8 8 table pointer<21> inc/dec logic 21 8 data bus<8> table latch 8 ir 12 3 rb2/int2/seg9 rb3/int3/seg10 pclatu pcu portd rd7/seg7:rd0/seg0 osc2/clko (3) /ra6 note 1: ccp2 is multiplexed with rc1 when configuration bit ccp2mx is set, or re7 when ccp2mx is not set. 2: rg5 is only available when mclr functionality is disabled. 3: osc1/clki and osc2/clko are only available in select oscillator modes and when these pins are not being used as digital i/o. refer to section 2.0 ?oscillator configurations? for additional information. rb4/kbi0/seg11 rb5/kbi1 rb6/kbi2/pgc rb7/kbi3/pgd eusart1 comparators mssp timer2 timer1 timer3 timer0 hlvd ccp1 bor adc 10-bit w instruction bus <16> stkptr bank 8 state machine control signals decode 8 8 power-up timer oscillator start-up timer power-on reset watchdog timer osc1 (3) osc2 (3) v dd , brown-out reset internal oscillator fail-safe clock monitor precision reference band gap v ss mclr (2) block intrc oscillator 8 mhz oscillator single-supply programming in-circuit debugger t1osi t1oso osc1/clki (3) /ra7 porte lcdbias1 lcdbias2 lcdbias3 com0 re4/com1 re5/com2 re6/com3 re7/ccp2 (1) /seg31 portf rf0/an5 /seg18 rf1/an6/c2out /seg19 rf2/an7/c1out /seg20 rf3/an8 /seg21 rf4/an9 /seg22 rf5/an10/cv ref /seg23 rf6/an11 /seg24 rf7/ss /seg25 portg rg0 /seg30 rg1/tx2/ck2 /seg29 rg2/rx2/dt2 /seg28 rg3 /seg27 rg4 /seg26 mclr /v pp /rg5 (2) ausart2 ccp2 lcd driver rom latch
? 2004 microchip technology inc. preliminary ds39629b-page 11 PIC18F6390/6490/8390/8490 figure 1-2: pic18f8x90 (80-pin) block diagram instruction decode and control data latch data memory (3.9 kbytes) address latch data address<12> 12 access bsr fsr0 fsr1 fsr2 inc/dec logic address 4124 pch pcl pclath 8 31 level stack program counter prodl prodh 8 x 8 multiply 8 bitop 8 8 alu<8> address latch program memory (48/64 kbytes) data latch 20 8 8 table pointer<21> inc/dec logic 21 8 data bus<8> table latch 8 ir 12 3 rom latch pclatu pcu note 1: ccp2 is multiplexed with rc1 when configuration bit ccp2mx is set and re7 when ccp2mx is not set. 2: rg5 is only available when mclr functionality is disabled. 3: osc1/clki and osc2/clko are only available in select oscillator modes and when these pins are not being used as digital i/o. refer to section 2.0 ?oscillator configurations? for additional information. eusart1 comparators mssp timer2 timer1 timer3 timer0 hlvd ccp1 bor adc 10-bit w instruction bus <16> stkptr bank 8 state machine control signals decode 8 8 power-up timer oscillator start-up timer power-on reset watchdog timer osc1 (3) osc2 (3) v dd , brown-out reset internal oscillator fail-safe clock monitor precision reference band gap v ss mclr (2) block intrc oscillator 8 mhz oscillator single-supply programming in-circuit debugger t1osi t1oso ausart2 ccp2 porth rh7/seg40:rh4/seg43 rh3/seg47:rh0/seg44 lcd driver porta portb portc ra4/t0cki/seg14 ra5/an4/hlvdin/seg15 rb0/int0 rc0/t1oso/t13cki rc1/t1osi/ccp2 (1) rc2/ccp1 /seg13 rc3/sck/scl rc4/sdi/sda rc5/sdo /seg12 rc6/tx1/ck1 rc7/rx1/dt1 ra3/an3/v ref +/seg17 ra2/an2/v ref -/seg16 ra1/an1 ra0/an0 rb1/int1/seg8 rb2/int2/seg9 rb3/int3/seg10 portd rd7/seg7:rd0/seg0 osc2/clko (3) /ra6 rb4/kbi0/seg11 rb5/kbi1 rb6/kbi2/pgc rb7/kbi3/pgd osc1/clki (3) /ra7 porte lcdbias1 lcdbias2 lcdbias3 com0 re4/com1 re5/com2 re6/com3 re7/ccp2 (1) /seg31 portf rf0/an5 /seg18 rf1/an6/c2out /seg19 rf2/an7/c1out /seg20 rf3/an8 /seg21 rf4/an9 /seg22 rf5/an10/cv ref /seg23 rf6/an11 /seg24 rf7/ss /seg25 portg rg0 /seg30 rg1/tx2/ck2 /seg29 rg2/rx2/dt2 /seg28 rg3 /seg27 rg4 /seg26 mclr /v pp /rg5 (2) portj rj7/seg36:rj4/seg39 rj3/seg35:rj0/seg32
PIC18F6390/6490/8390/8490 ds39629b-page 12 preliminary ? 2004 microchip technology inc. table 1-2: pic18f6x90 pinout i/o descriptions pin name pin number pin type buffer type description tqfp mclr /v pp /rg5 mclr v pp rg5 7 i p i st st master clear (input) or programming voltage (input). master clear (reset) input. this pin is an active-low reset to the device. programming voltage input. digital input. osc1/clki/ra7 osc1 clki ra7 39 i i i/o st cmos ttl oscillator crystal or external clock input. oscillator crystal input or external clock source input. st buffer when configured in rc mode, cmos otherwise. external clock source input. always associated with pin function osc1. (see related osc1/clki, osc2/clko pins.) general purpose i/o pin. osc2/clko/ra6 osc2 clko ra6 40 o o i/o ? ? ttl oscillator crystal or clock output. oscillator crystal output. connects to crystal or resonator in crystal oscillator mode. in rc mode, osc2 pin outputs clko, which has 1/4 the frequency of osc1 and denotes the instruction cycle rate. general purpose i/o pin. legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
? 2004 microchip technology inc. preliminary ds39629b-page 13 PIC18F6390/6490/8390/8490 porta is a bidirectional i/o port. ra0/an0 ra0 an0 24 i/o i ttl analog digital i/o. analog input 0. ra1/an1 ra1 an1 23 i/o i ttl analog digital i/o. analog input 1. ra2/an2/v ref -/seg16 ra2 an2 v ref - seg16 22 i/o i i o ttl analog analog analog digital i/o. analog input 2. a/d reference voltage (low) input. seg16 output for lcd. ra3/an3/v ref +/seg17 ra3 an3 v ref + seg17 21 i/o i i o ttl analog analog analog digital i/o. analog input 3. a/d reference voltage (high) input. seg17 output for lcd. ra4/t0cki/seg14 ra4 t0cki seg14 28 i/o i o st/od st analog digital i/o. open-drain when configured as output. timer0 external clock input. seg14 output for lcd. ra5/an4/hlvdin/seg15 ra5 an4 hlvdin seg15 27 i/o i i o ttl analog analog analog digital i/o. analog input 4. low-voltage detect input. seg15 output for lcd. ra6 see the osc2/clko/ra6 pin. ra7 see the osc1/clki/ra7 pin. table 1-2: pic18f6x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
PIC18F6390/6490/8390/8490 ds39629b-page 14 preliminary ? 2004 microchip technology inc. portb is a bidirectional i/o port. portb can be software programmed for internal weak pull-ups on all inputs. rb0/int0 rb0 int0 48 i/o i ttl st digital i/o. external interrupt 0. rb1/int1/seg8 rb1 int1 seg8 47 i/o i o ttl st analog digital i/o. external interrupt 1. seg8 output for lcd. rb2/int2/seg9 rb2 int2 seg9 46 i/o i o ttl st analog digital i/o. external interrupt 2. seg9 output for lcd. rb3/int3/seg10 rb3 int3 seg10 45 i/o i o ttl st analog digital i/o. external interrupt 3. seg10 output for lcd. rb4/kbi0/seg11 rb4 kbi0 seg11 44 i/o i o ttl ttl analog digital i/o. interrupt-on-change pin. seg11 output for lcd. rb5/kbi1 rb5 kbi1 43 i/o i ttl ttl digital i/o. interrupt-on-change pin. rb6/kbi2/pgc rb6 kbi2 pgc 42 i/o i i/o ttl ttl st digital i/o. interrupt-on-change pin. in-circuit debugger and icsp? programming clock pin. rb7/kbi3/pgd rb7 kbi3 pgd 37 i/o i i/o ttl ttl st digital i/o. interrupt-on-change pin. in-circuit debugger and icsp programming data pin. table 1-2: pic18f6x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
? 2004 microchip technology inc. preliminary ds39629b-page 15 PIC18F6390/6490/8390/8490 portc is a bidirectional i/o port. rc0/t1oso/t13cki rc0 t1oso t13cki 30 i/o o i st ? st digital i/o. timer1 oscillator output. timer1/timer3 external clock input. rc1/t1osi/ccp2 rc1 t1osi ccp2 (1) 29 i/o i i/o st cmos st digital i/o. timer1 oscillator input. capture2 input/compare2 output/pwm2 output. rc2/ccp1/seg13 rc2 ccp1 seg13 33 i/o i/o o st st analog digital i/o. capture1 input/compare1 output/pwm1 output. seg13 output for lcd. rc3/sck/scl rc3 sck scl 34 i/o i/o i/o st st st digital i/o. synchronous serial clock input/output for spi? mode. synchronous serial clock input/output for i 2 c? mode. rc4/sdi/sda rc4 sdi sda 35 i/o i i/o st st st digital i/o. spi data in. i 2 c data i/o. rc5/sdo/seg12 rc5 sdo seg12 36 i/o o o st ? analog digital i/o. spi data out. seg12 output for lcd. rc6/tx1/ck1 rc6 tx1 ck1 31 i/o o i/o st ? st digital i/o. eusart1 asynchronous transmit. eusart1 synchronous clock (see related rx1/dt1). rc7/rx1/dt1 rc7 rx1 dt1 32 i/o i i/o st st st digital i/o. eusart1 asynchronous receive. eusart1 synchronous data (see related tx1/ck1). table 1-2: pic18f6x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
PIC18F6390/6490/8390/8490 ds39629b-page 16 preliminary ? 2004 microchip technology inc. portd is a bidirectional i/o port. rd0/seg0 rd0 seg0 58 i/o o st analog digital i/o. seg0 output for lcd. rd1/seg1 rd1 seg1 55 i/o o st analog digital i/o. seg1 output for lcd. rd2/seg2 rd2 seg2 54 i/o o st analog digital i/o. seg2 output for lcd. rd3/seg3 rd3 seg3 53 i/o o st analog digital i/o. seg3 output for lcd. rd4/seg4 rd4 seg4 52 i/o o st analog digital i/o. seg4 output for lcd. rd5/seg5 rd5 seg5 51 i/o o st analog digital i/o. seg5 output for lcd. rd6/seg6 rd6 seg6 50 i/o o st analog digital i/o. seg6 output for lcd. rd7/seg7 rd7 seg7 49 i/o o st analog digital i/o. seg7 output for lcd. table 1-2: pic18f6x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
? 2004 microchip technology inc. preliminary ds39629b-page 17 PIC18F6390/6490/8390/8490 porte is a bidirectional i/o port. lcdbias1 lcdbias1 2 i analog bias1 input for lcd. lcdbias2 lcdbias2 1 i analog bias2 input for lcd. lcdbias3 lcdbias3 64 i analog bias3 input for lcd. com0 com0 63 o analog com0 output for lcd. re4/com1 re4 com1 62 i/o o st analog digital i/o. com1 output for lcd. re5/com2 re5 com2 61 i/o o st analog digital i/o. com2 output for lcd. re6/com3 re6 com3 60 i/o o st analog digital i/o. com3 output for lcd. re7/ccp2/seg31 re7 ccp2 (2) seg31 59 i/o i/o o st st analog digital i/o. capture 2 input/compare 2 output/pwm 2 output. seg31 output for lcd. table 1-2: pic18f6x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
PIC18F6390/6490/8390/8490 ds39629b-page 18 preliminary ? 2004 microchip technology inc. portf is a bidirectional i/o port. rf0/an5/seg18 rf0 an5 seg18 18 i/o i o st analog analog digital i/o. analog input 5. seg18 output for lcd. rf1/an6/c2out/seg19 rf1 an6 c2out seg19 17 i/o i o o st analog ? analog digital i/o. analog input 6. comparator 2 output. seg19 output for lcd. rf2/an7/c1out/seg20 rf2 an7 c1out seg20 16 i/o i o o st analog ? analog digital i/o. analog input 7. comparator 1 output. seg20 output for lcd. rf3/an8/seg21 rf3 an8 seg21 15 i/o i o st analog analog digital i/o. analog input 8. seg21 output for lcd. rf4/an9/seg22 rf4 an9 seg22 14 i/o i o st analog analog digital i/o. analog input 9. seg22 output for lcd. rf5/an10/cv ref /seg23 rf5 an10 cv ref seg23 13 i/o i o o st analog analog analog digital i/o. analog input 10. comparator reference voltage output. seg23 output for lcd. rf6/an11/seg24 rf6 an11 seg24 12 i/o i o st analog analog digital i/o. analog input 11. seg24 output for lcd. rf7/ss /seg25 rf7 ss seg25 11 i/o i o st ttl analog digital i/o. spi? slave select input. seg25 output for lcd. table 1-2: pic18f6x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
? 2004 microchip technology inc. preliminary ds39629b-page 19 PIC18F6390/6490/8390/8490 portg is a bidirectional i/o port. rg0/seg30 rg0 seg30 3 i/o o st analog digital i/o. seg30 output for lcd. rg1/tx2/ck2/seg29 rg1 tx2 ck2 seg29 4 i/o o i/o o st ? st analog digital i/o. ausart2 asynchronous transmit. ausart2 synchronous clock (see related rx2/dt2). seg29 output for lcd. rg2/rx2/dt2/seg28 rg2 rx2 dt2 seg28 5 i/o i i/o o st st st analog digital i/o. ausart2 asynchronous receive. ausart2 synchronous data (see related tx2/ck2). seg28 output for lcd. rg3/seg27 rg3 seg27 6 i/o o st analog digital i/o. seg27 output for lcd. rg4/seg26 rg4 seg26 8 i/o o st analog digital i/o. seg26 output for lcd. rg5 see mclr /v pp /rg5 pin. v ss 9, 25, 41, 56 p ? ground reference for logic and i/o pins. v dd 10, 26, 38, 57 p ? positive supply for logic and i/o pins. av ss 20 p ? ground reference for analog modules. av dd 19 p ? positive supply for analog modules. table 1-2: pic18f6x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
PIC18F6390/6490/8390/8490 ds39629b-page 20 preliminary ? 2004 microchip technology inc. table 1-3: pic18f8x90 pinout i/o descriptions pin name pin number pin type buffer type description tqfp mclr /v pp /rg5 mclr v pp rg5 9 i p i st st master clear (input) or programming voltage (input). master clear (reset) input. this pin is an active-low reset to the device. programming voltage input. digital input. osc1/clki/ra7 osc1 clki ra7 49 i i i/o st cmos ttl oscillator crystal or external clock input. oscillator crystal input or external clock source input. st buffer when configured in rc mode, cmos otherwise. external clock source input. always associated with pin function osc1. (see related osc1/clki, osc2/clko pins.) general purpose i/o pin. osc2/clko/ra6 osc2 clko ra6 50 o o i/o ? ? ttl oscillator crystal or clock output. oscillator crystal output. connects to crystal or resonator in crystal oscillator mode. in rc mode, osc2 pin outputs clko, which has 1/4 the frequency of osc1 and denotes the instruction cycle rate. general purpose i/o pin. legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
? 2004 microchip technology inc. preliminary ds39629b-page 21 PIC18F6390/6490/8390/8490 porta is a bidirectional i/o port. ra0/an0 ra0 an0 30 i/o i ttl analog digital i/o. analog input 0. ra1/an1 ra1 an1 29 i/o i ttl analog digital i/o. analog input 1. ra2/an2/v ref -/seg16 ra2 an2 v ref - seg16 28 i/o i i o ttl analog analog analog digital i/o. analog input 2. a/d reference voltage (low) input. seg16 output for lcd. ra3/an3/v ref +/seg17 ra3 an3 v ref + seg17 27 i/o i i o ttl analog analog analog digital i/o. analog input 3. a/d reference voltage (high) input. seg17 output for lcd. ra4/t0cki/seg14 ra4 t0cki seg14 34 i/o i o st/od st analog digital i/o. open-drain when configured as output. timer0 external clock input. seg14 output for lcd. ra5/an4/hlvdin/seg15 ra5 an4 hlvdin seg15 33 i/o i i o ttl analog analog analog digital i/o. analog input 4. low-voltage detect input. seg15 output for lcd. ra6 see the osc2/clko/ra6 pin. ra7 see the osc1/clki/ra7 pin. table 1-3: pic18f8x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
PIC18F6390/6490/8390/8490 ds39629b-page 22 preliminary ? 2004 microchip technology inc. portb is a bidirectional i/o port. portb can be software programmed for internal weak pull-ups on all inputs. rb0/int0 rb0 int0 58 i/o i ttl st digital i/o. external interrupt 0. rb1/int1/seg8 rb1 int1 seg8 57 i/o i o ttl st analog digital i/o. external interrupt 1. seg8 output for lcd. rb2/int2/seg9 rb2 int2 seg9 56 i/o i o ttl st analog digital i/o. external interrupt 2. seg9 output for lcd. rb3/int3/seg10 rb3 int3 seg10 55 i/o i o ttl st analog digital i/o. external interrupt 3. seg10 output for lcd. rb4/kbi0/seg11 rb4 kbi0 seg11 54 i/o i o ttl ttl analog digital i/o. interrupt-on-change pin. seg11 output for lcd. rb5/kbi1 rb5 kbi1 53 i/o i ttl ttl digital i/o. interrupt-on-change pin. rb6/kbi2/pgc rb6 kbi2 pgc 52 i/o i i/o ttl ttl st digital i/o. interrupt-on-change pin. in-circuit debugger and icsp? programming clock pin. rb7/kbi3/pgd rb7 kbi3 pgd 47 i/o i i/o ttl ttl st digital i/o. interrupt-on-change pin. in-circuit debugger and icsp programming data pin. table 1-3: pic18f8x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
? 2004 microchip technology inc. preliminary ds39629b-page 23 PIC18F6390/6490/8390/8490 portc is a bidirectional i/o port. rc0/t1oso/t13cki rc0 t1oso t13cki 36 i/o o i st ? st digital i/o. timer1 oscillator output. timer1/timer3 external clock input. rc1/t1osi/ccp2 rc1 t1osi ccp2 (1) 35 i/o i i/o st cmos st digital i/o. timer1 oscillator input. capture2 input/compare2 output/pwm2 output. rc2/ccp1/seg13 rc2 ccp1 seg13 43 i/o i/o o st st analog digital i/o. capture1 input/compare1 output/pwm1 output. seg13 output for lcd. rc3/sck/scl rc3 sck scl 44 i/o i/o i/o st st st digital i/o. synchronous serial clock input/output for spi? mode. synchronous serial clock input/output for i 2 c? mode. rc4/sdi/sda rc4 sdi sda 45 i/o i i/o st st st digital i/o. spi data in. i 2 c data i/o. rc5/sdo/seg12 rc5 sdo seg12 46 i/o o o st ? analog digital i/o. spi data out. seg12 output for lcd. rc6/tx1/ck1 rc6 tx1 ck1 37 i/o o i/o st ? st digital i/o. eusart1 asynchronous transmit. eusart1 synchronous clock (see related rx1/dt1). rc7/rx1/dt1 rc7 rx1 dt1 38 i/o i i/o st st st digital i/o. eusart1 asynchronous receive. eusart1 synchronous data (see related tx1/ck1). table 1-3: pic18f8x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
PIC18F6390/6490/8390/8490 ds39629b-page 24 preliminary ? 2004 microchip technology inc. portd is a bidirectional i/o port. rd0/seg0 rd0 seg0 72 i/o o st analog digital i/o. seg0 output for lcd. rd1/seg1 rd1 seg1 69 i/o o st analog digital i/o. seg1 output for lcd. rd2/seg2 rd2 seg2 68 i/o o st analog digital i/o. seg2 output for lcd. rd3/seg3 rd3 seg3 67 i/o o st analog digital i/o. seg3 output for lcd. rd4/seg4 rd4 seg4 66 i/o o st analog digital i/o. seg4 output for lcd. rd5/seg5 rd5 seg5 65 i/o o st analog digital i/o. seg5 output for lcd. rd6/seg6 rd6 seg6 64 i/o o st analog digital i/o. seg6 output for lcd. rd7/seg7 rd7 seg7 63 i/o o st analog digital i/o. seg7 output for lcd. table 1-3: pic18f8x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
? 2004 microchip technology inc. preliminary ds39629b-page 25 PIC18F6390/6490/8390/8490 porte is a bidirectional i/o port. lcdbias1 lcdbias1 4 i analog bias1 input for lcd. lcdbias2 lcdbias2 3 i analog bias2 input for lcd. lcdbias3 lcdbias3 78 i analog bias3 input for lcd. com0 com0 77 o analog com0 output for lcd. re4/com1 re4 com1 76 i/o o st analog digital i/o. com1 output for lcd. re5/com2 re5 com2 75 i/o o st analog digital i/o. com2 output for lcd. re6/com3 re6 com3 74 i/o o st analog digital i/o. com3 output for lcd. re7/ccp2/seg31 re7 ccp2 (2) seg31 73 i/o i/o o st st analog digital i/o. capture 2 input/compare 2 output/pwm 2 output. seg31 output for lcd. table 1-3: pic18f8x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
PIC18F6390/6490/8390/8490 ds39629b-page 26 preliminary ? 2004 microchip technology inc. portf is a bidirectional i/o port. rf0/an5/seg18 rf0 an5 seg18 24 i/o i o st analog analog digital i/o. analog input 5. seg18 output for lcd. rf1/an6/c2out/seg19 rf1 an6 c2out seg19 23 i/o i o o st analog ? analog digital i/o. analog input 6. comparator 2 output. seg19 output for lcd. rf2/an7/c1out/seg20 rf2 an7 c1out seg20 18 i/o i o o st analog ? analog digital i/o. analog input 7. comparator 1 output. seg20 output for lcd. rf3/an8/seg21 rf3 an8 seg21 17 i/o i o st analog analog digital i/o. analog input 8. seg21 output for lcd. rf4/an9/seg22 rf4 an9 seg22 16 i/o i o st analog analog digital i/o. analog input 9. seg22 output for lcd. rf5/an10/cv ref /seg23 rf5 an10 cv ref seg23 15 i/o i o o st analog analog analog digital i/o. analog input 10. comparator reference voltage output. seg23 output for lcd. rf6/an11/seg24 rf6 an11 seg24 14 i/o i o st analog analog digital i/o. analog input 11. seg24 output for lcd. rf7/ss /seg25 rf7 ss seg25 13 i/o i o st ttl analog digital i/o. spi? slave select input. seg25 output for lcd. table 1-3: pic18f8x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
? 2004 microchip technology inc. preliminary ds39629b-page 27 PIC18F6390/6490/8390/8490 portg is a bidirectional i/o port. rg0/seg30 rg0 seg30 5 i/o o st analog digital i/o. seg30 output for lcd. rg1/tx2/ck2/seg29 rg1 tx2 ck2 seg29 6 i/o o i/o o st ? st analog digital i/o. ausart2 asynchronous transmit. ausart2 synchronous clock (see related rx2/dt2). seg29 output for lcd. rg2/rx2/dt2/seg28 rg2 rx2 dt2 seg28 7 i/o i i/o o st st st analog digital i/o. ausart2 asynchronous receive. ausart2 synchronous data (see related tx2/ck2). seg28 output for lcd. rg3/seg27 rg3 seg27 8 i/o o st analog digital i/o. seg27 output for lcd. rg4/seg26 rg4 seg26 10 i/o o st analog digital i/o. seg26 output for lcd. rg5 see mclr /v pp /rg5 pin. table 1-3: pic18f8x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
PIC18F6390/6490/8390/8490 ds39629b-page 28 preliminary ? 2004 microchip technology inc. porth is a bidirectional i/o port. rh0/seg47 rh0 seg47 79 i/o o st analog digital i/o. seg47 output for lcd. rh1/seg46 rh1 seg46 80 i/o o st analog digital i/o. seg46 output for lcd. rh2/seg45 rh2 seg45 1 i/o o st analog digital i/o. seg45 output for lcd. rh3/seg44 rh3 seg44 2 i/o o st analog digital i/o. seg44 output for lcd. rh4/seg40 rh4 seg40 22 i/o o st analog digital i/o. seg40 output for lcd. rh5/seg41 rh5 seg41 21 i/o o st analog digital i/o. seg41 output for lcd. rh6/seg42 rh6 seg42 20 i/o o st analog digital i/o. seg42 output for lcd. rh7/seg43 rh7 seg43 19 i/o o st analog digital i/o. seg43 output for lcd. table 1-3: pic18f8x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
? 2004 microchip technology inc. preliminary ds39629b-page 29 PIC18F6390/6490/8390/8490 portj is a bidirectional i/o port. rj0/seg32 rj0 seg32 62 i/o o st analog digital i/o. seg32 output for lcd. rj1/seg33 rj1 seg33 61 i/o o st analog digital i/o. seg33 output for lcd. rj2/seg34 rj2 seg34 60 i/o o st analog digital i/o. seg34 output for lcd. rj3/seg35 rj3 seg35 59 i/o o st analog digital i/o. seg35 output for lcd. rj4/seg39 rj4 seg39 39 i/o o st analog digital i/o. seg39 output for lcd. rj5/seg38 rj5 seg38 40 i/o o st analog digital i/o seg38 output for lcd. rj6/seg37 rj6 seg37 41 i/o o st analog digital i/o. seg37 output for lcd. rj7/seg36 rj7 seg36 42 i/o o st analog digital i/o. seg36 output for lcd. v ss 11, 31, 51, 70 p ? ground reference for logic and i/o pins. v dd 12, 32, 48, 71 p ? positive supply for logic and i/o pins. av ss 26 p ? ground reference for analog modules. av dd 25 p ? positive supply for analog modules. table 1-3: pic18f8x90 pinout i/o descriptions (continued) pin name pin number pin type buffer type description tqfp legend: ttl = ttl compatible input cmos = cmos compatible input or output st = schmitt trigger input with cmos levels analog = analog input i = input o = output p = power od = open-drain (no p diode to v dd ) note 1: default assignment for ccp2 when configuration bit ccp2mx is set. 2: alternate assignment for ccp2 when configuration bit ccp2mx is cleared.
PIC18F6390/6490/8390/8490 ds39629b-page 30 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 31 PIC18F6390/6490/8390/8490 2.0 oscillator configurations 2.1 oscillator types PIC18F6390/6490/8390/8490 devices can be operated in ten different oscillator modes. the user can program the configuration bits, fosc3:fosc0, in configuration register 1h to select one of these ten modes: 1. lp low-power crystal 2. xt crystal/resonator 3. hs high-speed crystal/resonator 4. hspll high-speed crystal/resonator with pll enabled 5. rc external resistor/capacitor with f osc /4 output on ra6 6. rcio external resistor/capacitor with i/o on ra6 7. intio1 internal oscillator with f osc /4 output on ra6 and i/o on ra7 8. intio2 internal oscillator with i/o on ra6 and ra7 9. ec external clock with f osc /4 output 10. ecio external clock with i/o on ra6 2.2 crystal oscillator/ceramic resonators in xt, lp, hs or hspll oscillator modes, a crystal or ceramic resonator is connected to the osc1 and osc2 pins to establish oscillation. figure 2-1 shows the pin connections. the oscillator design requires the use of a parallel cut crystal. figure 2-1: crystal/ceramic resonator operation (xt, lp, hs or hspll configuration) table 2-1: capacitor selection for ceramic resonators note: use of a series cut crystal may give a fre- quency out of the crystal manufacturer?s specifications. typical capacitor values used: mode freq osc1 osc2 xt 455 khz 2.0 mhz 4.0 mhz 56 pf 47 pf 33 pf 56 pf 47 pf 33 pf hs 8.0 mhz 16.0 mhz 27 pf 22 pf 27 pf 22 pf capacitor values are for design guidance only. these capacitors were tested with the resonators listed below for basic start-up and operation. these values are not optimized . different capacitor values may be required to produce acceptable oscillator operation. the user should test the performance of the oscillator over the expected v dd and temperature range for the application. see the notes following table 2-2 for additional information. resonators used: 455 khz 4.0 mhz 2.0 mhz 8.0 mhz 16.0 mhz note 1: see table 2-1 and table 2-2 for initial values of c1 and c2. 2: a series resistor (r s ) may be required for at strip cut crystals. 3: r f varies with the oscillator mode chosen. c1 (1) c2 (1) xtal osc2 osc1 r f (3) sleep to logic pic18fxxxx r s (2) internal
PIC18F6390/6490/8390/8490 ds39629b-page 32 preliminary ? 2004 microchip technology inc. table 2-2: capacitor selection for crystal oscillator an external clock source may also be connected to the osc1 pin in the hs mode, as shown in figure 2-2. figure 2-2: external clock input operation (hs configuration) 2.3 external clock input the ec and ecio oscillator modes require an external clock source to be connected to the osc1 pin. there is no oscillator start-up time required after a power-on reset or after an exit from sleep mode. in the ec oscillator mode, the oscillator frequency divided by 4 is available on the osc2 pin. this signal may be used for test purposes or to synchronize other logic. figure 2-3 shows the pin connections for the ec oscillator mode. figure 2-3: external clock input operation (ec configuration) the ecio oscillator mode functions like the ec mode, except that the osc2 pin becomes an additional gen- eral purpose i/o pin. the i/o pin becomes bit 6 of porta (ra6). figure 2-4 shows the pin connections for the ecio oscillator mode. figure 2-4: external clock input operation (ecio configuration) osc type crystal freq typical capacitor values tested: c1 c2 lp 32 khz 33 pf 33 pf 200 khz 15 pf 15 pf xt 1 mhz 33 pf 33 pf 4 mhz 27 pf 27 pf hs 4 mhz 27 pf 27 pf 8 mhz 22 pf 22 pf 20 mhz 15 pf 15 pf capacitor values are for design guidance only. these capacitors were tested with the crystals listed below for basic start-up and operation. these values are not optimized. different capacitor values may be required to produce acceptable oscillator operation. the user should test the performance of the oscillator over the expected v dd and temperature range for the application. see the notes following this table for additional information. crystals used: 32 khz 4 mhz 200 khz 8 mhz 1 mhz 20 mhz note 1: higher capacitance increases the stability of oscillator, but also increases the start-up time. 2: when operating below 3v v dd , or when using certain ceramic resonators at any voltage, it may be necessary to use the hs mode or switch to a crystal oscillator. 3: since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components. 4: rs may be required to avoid overdriving crystals with low drive level specification. 5: always verify oscillator performance over the v dd and temperature range that is expected for the application. osc1 osc2 open clock from ext. system pic18fxxxx (hs mode) osc1/clki osc2/clko f osc /4 clock from ext. system pic18fxxxx osc1/clki i/o (osc2) ra6 clock from ext. system pic18fxxxx
? 2004 microchip technology inc. preliminary ds39629b-page 33 PIC18F6390/6490/8390/8490 2.4 rc oscillator for timing insensitive applications, the ?rc? and ?rcio? device options offer additional cost savings. the actual oscillator frequency is a function of several factors: supply voltage values of the external resistor (r ext ) and capacitor (c ext ) operating temperature given the same device, operating voltage and temperature and component values, there will also be unit-to-unit frequency variations. these are due to factors such as: normal manufacturing variation difference in lead frame capacitance between package types (especially for low c ext values) variations within the tolerance of limits of r ext and c ext in the rc oscillator mode, the oscillator frequency divided by 4 is available on the osc2 pin. this signal may be used for test purposes or to synchronize other logic. figure 2-5 shows how the r/c combination is connected. figure 2-5: rc oscillator mode the rcio oscillator mode (figure 2-6) functions like the rc mode, except that the osc2 pin becomes an additional general purpose i/o pin. the i/o pin becomes bit 6 of porta (ra6). figure 2-6: rcio oscillator mode 2.5 pll frequency multiplier a phase locked loop (pll) circuit is provided as an option for users who want to use a lower frequency oscillator circuit, or to clock the device up to its highest rated frequency from a crystal oscillator. this may be useful for customers who are concerned with emi due to high-frequency crystals, or users who require higher clock speeds from an internal oscillator. 2.5.1 hspll oscillator mode the hspll mode makes use of the hs mode oscillator for frequencies up to 10 mhz. a pll then multiplies the oscillator output frequency by 4 to produce an internal clock frequency up to 40 mhz. the pll is only available to the crystal oscillator when the fosc3:fosc0 configuration bits are programmed for hspll mode (= 0110 ). figure 2-7: pll block diagram (hs mode) 2.5.2 pll and intosc the pll is also available to the internal oscillator block in selected oscillator modes. in this configuration, the pll is enabled in software and generates a clock output of up to 32 mhz. the operation of intosc with the pll is described in section 2.6.4 ?pll in intosc modes? . osc2/clko c ext r ext pic18fxxxx osc1 f osc /4 internal clock v dd v ss recommended values: 3 k ? r ext 100 k ? c ext > 20 pf c ext r ext pic18fxxxx osc1 internal clock v dd v ss recommended values: 3 k ? r ext 100 k ? c ext > 20 pf i/o (osc2) ra6 mux vco loop filter crystal oscillator osc2 osc1 pll enable f in f out sysclk phase comparator hs oscillator enable 4 (from configuration register 1h) hs mode
PIC18F6390/6490/8390/8490 ds39629b-page 34 preliminary ? 2004 microchip technology inc. 2.6 internal oscillator block the PIC18F6390/6490/8390/8490 devices include an internal oscillator block, which generates two different clock signals; either can be used as the micro- controller?s clock source. this may eliminate the need for external oscillator circuits on the osc1 and/or osc2 pins. the main output (intosc) is an 8 mhz clock source, which can be used to directly drive the device clock. it also drives a postscaler, which can provide a range of clock frequencies from 31 khz to 4 mhz. the intosc output is enabled when a clock frequency from 125 khz to 8 mhz is selected. the other clock source is the internal rc oscillator (intrc), which provides a nominal 31 khz output. intrc is enabled if it is selected as the device clock source; it is also enabled automatically when any of the following are enabled: power-up timer fail-safe clock monitor watchdog timer two-speed start-up lcd with intrc as its clock source these features are discussed in greater detail in section 23.0 ?special features of the cpu? . the clock source frequency (intosc direct, intrc direct or intosc postscaler) is selected by configuring the ircf bits of the osccon register (register 2-2). 2.6.1 intio modes using the internal oscillator as the clock source elimi- nates the need for up to two external oscillator pins, which can then be used for digital i/o. two distinct configurations are available: in intio1 mode, the osc2 pin outputs f osc /4, while osc1 functions as ra7 for digital input and output. in intio2 mode, osc1 functions as ra7 and osc2 functions as ra6, both for digital input and output. 2.6.2 intosc output frequency the internal oscillator block is calibrated at the factory to produce an intosc output frequency of 8.0 mhz. the intrc oscillator operates independently of the intosc source. any changes in intosc across voltage and temperature are not necessarily reflected by changes in intrc and vice versa. 2.6.3 osctune register the internal oscillator?s output has been calibrated at the factory, but can be adjusted in the user?s applica- tion. this is done by writing to the osctune register (register 2-1). the tuning sensitivity is constant throughout the tuning range. when the osctune register is modified, the intosc and intrc frequencies will begin shifting to the new frequency. the intrc clock will reach the new frequency within 8 clock cycles (approximately 8*32 s = 256 s). the intosc clock will stabilize within 1 ms. code execution continues during this shift. there is no indication that the shift has occurred. the osctune register also implements the intsrc and pllen bits, which control certain features of the internal oscillator block. the intsrc bit allows users to select which internal oscillator provides the clock source when the 31 khz frequency option is selected. this is covered in greater detail in section 2.7.1 ?oscillator control register? . the pllen bit controls the operation of the frequency multiplier, pll, in internal oscillator modes. 2.6.4 pll in intosc modes the 4x frequency multiplier can be used with the inter- nal oscillator block to produce faster device clock speeds than are normally possible with an internal oscillator. when enabled, the pll produces a clock speed of up to 32 mhz. unlike hspll mode, the pll is controlled through software. the control bit, pllen (osctune<6>), is used to enable or disable its operation. the pll is available when the device is configured to use the internal oscillator block as its primary clock source (fosc3:fosc0 = 1001 or 1000 ). additionally, the pll will only function when the selected output frequency is either 4 mhz or 8 mhz (osccon<6:4> = 111 or 110 ). if both of these conditions are not met, the pll is disabled. the pllen control bit is only functional in those inter- nal oscillator modes where the pll is available. in all other modes, it is forced to ? 0 ? and is effectively unavailable. 2.6.5 intosc frequency drift the factory calibrates the internal oscillator block output (intosc) for 8 mhz. however, this frequency may drift as v dd or temperature changes, which can affect the controller operation in a variety of ways. it is possible to adjust the intosc frequency by modifying the value in the ostune register. this has no effect on the intrc clock source frequency. tuning the intosc source requires knowing when to make the adjustment, in which direction it should be made and in some cases, how large a change is needed. three compensation techniques are discussed in section 2.6.5.1 ?compensating with the ausart? , section 2.6.5.2 ?compensating with the timers? and section 2.6.5.3 ?compensating with the timers? , but other techniques may be used.
? 2004 microchip technology inc. preliminary ds39629b-page 35 PIC18F6390/6490/8390/8490 2.6.5.1 compensating with the ausart an adjustment may be required when the ausart begins to generate framing errors or receives data with errors while in asynchronous mode. framing errors indicate that the device clock frequency is too high. to adjust for this, decrement the value in ostune to reduce the clock frequency. on the other hand, errors in data may suggest that the clock speed is too low. to compensate, increment ostune to increase the clock frequency. 2.6.5.2 compensating with the timers this technique compares device clock speed to some reference clock. two timers may be used; one timer is clocked by the peripheral clock, while the other is clocked by a fixed reference source, such as the timer1 oscillator. both timers are cleared, but the timer clocked by the reference generates interrupts. when an interrupt occurs, the internally clocked timer is read and both timers are cleared. if the internally clocked timer value is greater than expected, then the internal oscillator block is running too fast. to adjust for this, decrement the osctune register. 2.6.5.3 compensating with the timers a ccp module can use free running timer1 (or timer3), clocked by the internal oscillator block and an external event with a known period (i.e., ac power frequency). the time of the first event is captured in the ccprxh:ccprxl registers and is recorded. when the second event causes a capture, the time of the first event is subtracted from the time of the second event. since the period of the external event is known, the time difference between events can be calculated. if the measured time is much greater than the calculated time, then the internal oscillator block is running too fast. to compensate, decrement the ostune register. if the measured time is much less than the calculated time, then the internal oscillator block is running too slow. to compensate, increment the ostune register. register 2-1: osctune: oscillator tuning register r/w-0 r/w-0 (1) u-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 intsrc pllen (1) ? tun4 tun3 tun2 tun1 tun0 bit 7 bit 0 bit 7 intsrc: internal oscillator low-frequency source select bit 1 = 31.25 khz device clock derived from 8 mhz intosc source (divide-by-256 enabled) 0 = 31 khz device clock derived directly from intrc internal oscillator bit 6 pllen: frequency multiplier pll for intosc enable bit (1) 1 = pll enabled for intosc (4 mhz and 8 mhz only) 0 = pll disabled note 1: available only in certain oscillator configurations; otherwise, this bit is unavailable and read as ? 0 ?. see section 2.6.4 ?pll in intosc modes? for details. bit 5 unimplemented: read as ? 0 ? bit 4-0 tun4:tun0: frequency tuning bits 01111 = maximum frequency 00001 00000 = center frequency. oscillator module is running at the calibrated frequency. 11111 10000 = minimum frequency legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 36 preliminary ? 2004 microchip technology inc. 2.7 clock sources and oscillator switching like previous pic18 devices, the PIC18F6390/6490/8390/8490 family includes a feature that allows the device clock source to be switched from the main oscillator to an alternate low-frequency clock source. PIC18F6390/6490/8390/8490 devices offer two alternate clock sources. when an alternate clock source is enabled, the various power managed operat- ing modes are available. essentially, there are three clock sources for these devices: primary oscillators secondary oscillators internal oscillator block the primary oscillators include the external crystal and resonator modes, the external rc modes, the external clock modes and the internal oscillator block. the particular mode is defined by the fosc3:fosc0 configuration bits. the details of these modes are covered earlier in this chapter. the secondary oscillators are those external sources not connected to the osc1 or osc2 pins. these sources may continue to operate even after the controller is placed in a power managed mode. PIC18F6390/6490/8390/8490 devices offer the timer1 oscillator as a secondary oscillator. this oscillator, in all power managed modes, is often the time base for func- tions such as a real-time clock. most often, a 32.768 khz watch crystal is connected between the rc0/t1oso/t13cki and rc1/t1osi pins. like the lp mode oscillator circuit, loading capacitors are also connected from each pin to ground. the timer1 oscillator is discussed in greater detail in section 11.3 ?timer1 oscillator? . in addition to being a primary clock source, the internal oscillator block is available as a power managed mode clock source. the intrc source is also used as the clock source for several special features, such as the wdt and fail-safe clock monitor. the clock sources for the PIC18F6390/6490/8390/8490 devices are shown in figure 2-8. see section 23.0 ?special features of the cpu? for configuration register details. figure 2-8: PIC18F6390/6490/8390/8490 clock diagram pic18f6x90/8x90 4 x pll fosc3:fosc0 secondary oscillator t1oscen enable oscillator t1oso t1osi clock source option for other modules osc1 osc2 sleep primary oscillator hspll, intosc/pll lp, xt, hs, rc, ec t1osc cpu peripherals idlen postscaler mux mux 8 mhz 4 mhz 2 mhz 1 mhz 500 khz 125 khz 250 khz osccon<6:4> 111 110 101 100 011 010 001 000 31 khz intrc source internal oscillator block wdt, pwrt, fscm 8 mhz internal oscillator (intosc) osccon<6:4> clock control osccon<1:0> source 8 mhz 31 khz (intrc) osctune<6> 0 1 osctune<7> and two-speed start-up
? 2004 microchip technology inc. preliminary ds39629b-page 37 PIC18F6390/6490/8390/8490 2.7.1 oscillator control register the osccon register (register 2-2) controls several aspects of the device clock?s operation, both in full power operation and in power managed modes. the system clock select bits, scs1:scs0, select the clock source. the available clock sources are the pri- mary clock (defined by the fosc:fosc0 configuration bits), the secondary clock (timer1 oscillator) and the internal oscillator block. the clock source changes immediately after one or more of the bits is written to, following a brief clock transition interval. the scs bits are cleared on all forms of reset. the internal oscillator frequency select bits, ircf2:ircf0, select the frequency output of the internal oscillator block to drive the device clock. the choices are the intrc source, the intosc source (8 mhz) or one of the frequencies derived from the intosc postscaler (31.25 khz to 4 mhz). if the internal oscillator block is supplying the device clock, changing the states of these bits will have an immediate change on the internal oscillator?s output. when an output frequency of 31 khz is selected (ircf2:ircf0 = 000 ), users may choose which inter- nal oscillator acts as the source. this is done with the intsrc bit in the osctune register (osctune<7>). setting this bit selects intosc as a 31.25 khz clock source by enabling the divide-by-256 output of the intosc postscaler. clearing intsrc selects intrc (nominally 31 khz) as the clock source. this option allows users to select the tunable and more precise intosc as a clock source, while maintaining power savings with a very low clock speed. regardless of the setting of intsrc, intrc always remains the clock source for features such as the watchdog timer and the fail-safe clock monitor. the osts, iofs and t1run bits indicate which clock source is currently providing the device clock. the osts bit indicates that the oscillator start-up timer has timed out and the primary clock is providing the device clock in primary clock modes. the iofs bit indicates when the internal oscillator block has stabilized and is providing the device clock in rc clock modes. the t1run bit (t1con<6>) indicates when the timer1 oscillator is providing the device clock in secondary clock modes. in power managed modes, only one of these three bits will be set at any time. if none of these bits are set, the intrc is providing the clock, or the internal oscillator block has just started and is not yet stable. the idlen bit determines if the device goes into sleep mode or one of the idle modes when the sleep instruction is executed. the use of the flag and control bits in the osccon register is discussed in more detail in section 3.0 ?power managed modes? . 2.7.2 oscillator transitions PIC18F6390/6490/8390/8490 devices contain circuitry to prevent clock ?glitches? when switching between clock sources. a short pause in the device clock occurs during the clock switch. the length of this pause is the sum of two cycles of the old clock source and three to four cycles of the new clock source. this formula assumes that the new clock source is stable. clock transitions are discussed in greater detail in section 3.1.2 ?entering power managed modes? . note 1: the timer1 oscillator must be enabled to select the secondary clock source. the timer1 oscillator is enabled by setting the t1oscen bit in the timer1 control regis- ter (t1con<3>). if the timer1 oscillator is not enabled, then any attempt to select a secondary clock source when executing a sleep instruction will be ignored. 2: it is recommended that the timer1 oscillator be operating and stable before executing the sleep instruction, or a very long delay may occur while the timer1 oscillator starts.
PIC18F6390/6490/8390/8490 ds39629b-page 38 preliminary ? 2004 microchip technology inc. register 2-2: osccon: oscillator co ntrol register r/w-0 r/w-1 r/w-0 r/w-0 r (1) r-0 r/w-0 r/w-0 idlen ircf2 ircf1 ircf0 osts iofs scs1 scs0 bit 7 bit 0 bit 7 idlen: idle enable bit 1 = device enters idle mode on sleep instruction 0 = device enters sleep mode on sleep instruction bit 6-4 ircf2:ircf0: internal oscillator frequency select bits 111 = 8 mhz (intosc drives clock directly) 110 = 4 mhz 101 = 2 mhz 100 = 1 mhz (3) 011 = 500 khz 010 = 250 khz 001 = 125 khz 000 = 31 khz (from either intosc/256 or intrc directly (2) ) bit 3 osts: oscillator start-up time-out status bit (1) 1 = oscillator start-up timer time-out has expired; primary oscillator is running 0 = oscillator start-up timer time-out is running; primary oscillator is not ready bit 2 iofs: intosc frequency stable bit 1 = intosc frequency is stable 0 = intosc frequency is not stable bit 1-0 scs1:scs0: system clock select bits 1x = internal oscillator block 01 = timer1 oscillator 00 = primary oscillator note 1: depends on state of the ieso configuration bit. 2: source selected by the intsrc bit (osctune<7>), see section 2.6.3 ?osctune register? . 3: default output frequency of intosc on reset. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
? 2004 microchip technology inc. preliminary ds39629b-page 39 PIC18F6390/6490/8390/8490 2.8 effects of power managed modes on the various clock sources when pri_idle mode is selected, the designated pri- mary oscillator continues to run without interruption. for all other power managed modes, the oscillator using the osc1 pin is disabled. the osc1 pin (and osc2 pin, if used by the oscillator) will stop oscillating. in secondary clock modes (sec_run and sec_idle), the timer1 oscillator is operating and providing the device clock. the timer1 oscillator may also run in all power managed modes if required to clock timer1 or timer3. in internal oscillator modes (rc_run and rc_idle), the internal oscillator block provides the device clock source. the 31 khz intrc output can be used directly to provide the clock and may be enabled to support var- ious special features, regardless of the power managed mode (see section 23.2 ?watchdog timer (wdt)? through section 23.4 ?fail-safe clock monitor? for more information on wdt, fail-safe clock monitor and two-speed start-up). the intosc output at 8 mhz may be used directly to clock the device, or may be divided down by the postscaler. the intosc output is disabled if the clock is provided directly from the intrc output. if the sleep mode is selected, all clock sources are stopped. since all the transistor switching currents have been stopped, sleep mode achieves the lowest current consumption of the device (only leakage currents). enabling any on-chip feature that will operate during sleep will increase the current consumed during sleep. the intrc is required to support wdt operation. the timer1 oscillator may be operating to support a real-time clock. other features may be operating that do not require a device clock source (i.e., ssp slave, intn pins and others). peripherals that may add signif- icant current consumption are listed in section 26.2 ?dc characteristics: power-down and supply current? . 2.9 power-up delays power-up delays are controlled by two timers, so that no external reset circuitry is required for most applications. the delays ensure that the device is kept in reset until the device power supply is stable under normal circum- stances and the primary clock is operating and stable. for additional information on power-up delays, see section 4.5 ?device reset timers? . the first timer is the power-up timer (pwrt), which provides a fixed delay on power-up (parameter 33, table 26-10). it is enabled by clearing (= 0 ) the pwrten configuration bit. the second timer is the oscillator start-up timer (ost), intended to keep the chip in reset until the crystal oscillator is stable (lp, xt and hs modes). the ost does this by counting 1024 oscillator cycles before allowing the oscillator to clock the device. when the hspll oscillator mode is selected, the device is kept in reset for an additional 2 ms, following the hs mode ost delay, so the pll can lock to the incoming clock frequency. there is a delay of interval t csd (parameter 38, table 26-10) following por while the controller becomes ready to execute instructions. this delay runs concurrently with any other delays. this may be the only delay that occurs when any of the ec, rc or intio modes are used as the primary clock source. table 2-3: osc1 and osc2 pin states in sleep mode oscillator mode osc1 pin osc2 pin rc, intio1 floating, external resistor should pull high at logic low (clock/4 output) rcio, intio2 floating, external resistor should pull high configured as porta, bit 6 ecio floating, pulled by external clock configured as porta, bit 6 ec floating, pulled by external clock at logic low (clock/4 output) lp, xt and hs feedback inverter disabled at quiescent voltage level feedback inverter disabled at quiescent voltage level note: see table 4-2 in section 4.0 ?reset? for time-outs due to sleep and mclr reset.
PIC18F6390/6490/8390/8490 ds39629b-page 40 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 41 PIC18F6390/6490/8390/8490 3.0 power managed modes PIC18F6390/6490/8390/8490 devices offer a total of seven operating modes for more efficient power management. these modes provide a variety of options for selective power conservation in applications where resources may be limited (i.e., battery-powered devices). there are three categories of power managed modes: sleep mode idle modes run modes these categories define which portions of the device are clocked and sometimes, what speed. the run and idle modes may use any of the three available clock sources (primary, secondary or intosc multiplexer); the sleep mode does not use a clock source. the power managed modes include several power saving features. one of these is the clock switching feature, offered in other pic18 devices, allowing the controller to use the timer1 oscillator in place of the primary oscillator. also included is the sleep mode, offered by all picmicro ? devices, where all device clocks are stopped. 3.1 selecting power managed modes selecting a power managed mode requires deciding if the cpu is to be clocked or not and selecting a clock source. the idlen bit controls cpu clocking, while the scs1:scs0 bits select a clock source. the individual modes, bit settings, clock sources and affected modules are summarized in table 3-1. 3.1.1 clock sources the scs1:scs0 bits allow the selection of one of three clock sources for power managed modes. they are: the primary clock, as defined by the fosc3:fosc0 configuration bits the secondary clock (the timer1 oscillator) the internal oscillator block (for rc modes) 3.1.2 entering power managed modes entering power managed run mode, or switching from one power managed mode to another, begins by loading the osccon register. the scs1:scs0 bits select the clock source and determine which run or idle mode is being used. changing these bits causes an immediate switch to the new clock source, assuming that it is running. the switch may also be subject to clock transition delays. these are discussed in section 3.1.3 ?clock transitions and status indicators? and subsequent sections. entry to the power managed idle or sleep modes is triggered by the execution of a sleep instruction. the actual mode that results depends on the status of the idlen bit. depending on the current mode and the mode being switched to, a change to a power managed mode does not always require setting all of these bits. many transi- tions may be done by changing the oscillator select bits, or changing the idlen bit prior to issuing a sleep instruction. if the idlen bit is already configured correctly, it may only be necessary to perform a sleep instruction to switch to the desired mode. table 3-1: power managed modes mode osccon bits module clocking available clock and oscillator source idlen (1) <7> scs1:scs0 <1:0> cpu peripherals sleep 0 n/a off off none ? all clocks are disabled pri_run n/a 00 clocked clocked primary ? lp, xt, hs, hspll, rc, ec, intrc (2) : this is the normal full power execution mode. sec_run n/a 01 clocked clocked secondary ? timer1 oscillator rc_run n/a 1x clocked clocked internal oscillator block (2) pri_idle 100 off clocked primary ? lp, xt, hs, hspll, rc, ec sec_idle 101 off clocked secondary ? timer1 oscillator rc_idle 11x off clocked internal oscillator block (2) note 1: idlen reflects its value when the sleep instruction is executed. 2: includes intosc and intosc postsc aler, as well as the intrc source.
PIC18F6390/6490/8390/8490 ds39629b-page 42 preliminary ? 2004 microchip technology inc. 3.1.3 clock transitions and status indicators the length of the transition between clock sources is the sum of two cycles of the old clock source and three to four cycles of the new clock source. this formula assumes that the new clock source is stable. three bits indicate the current clock source and its status. they are: osts (osccon<3>) iofs (osccon<2>) t1run (t1con<6>) in general, only one of these bits will be set while in a given power managed mode. when the osts bit is set, the primary clock is providing the device clock. when the iofs bit is set, the intosc output provides a stable 8 mhz clock source to a divider that actually drives the device clock. when the t1run bit is set, the timer1 oscillator provides the clock. if none of these bits are set, then either the intrc clock source clocks the device, or the intosc source is not yet stable. if the internal oscillator block is configured as the primary clock source by the fosc3:fosc0 configuration bits, then both the osts and iofs bits may be set when in pri_run or pri_idle modes. this indicates that the primary clock (intosc output) is generating a stable 8 mhz output. entering another rc power managed mode at the same frequency would clear the osts bit. 3.1.4 multiple sleep commands the power managed mode that is invoked with the sleep instruction is determined by the setting of the idlen bit at the time the instruction is executed. if another sleep instruction is executed, the device will enter the power managed mode specified by idlen at that time. if idlen has changed, the device will enter the new power managed mode specified by the new setting. 3.2 run modes in the run modes, clocks to both the core and peripherals are active. the difference between these modes is the clock source. 3.2.1 pri_run mode the pri_run mode is the normal full power execution mode of the microcontroller. this is also the default mode upon a device reset unless two-speed start-up is enabled (see section 23.3 ?two-speed start-up? for details). in this mode, the osts bit is set. the iofs bit may be set if the internal oscillator block is the primary clock source (see section 2.7.1 ?oscillator control register? ). 3.2.2 sec_run mode the sec_run mode is the compatible mode to the ?clock switching? feature offered in other pic18 devices. in this mode, the cpu and peripherals are clocked from the timer1 oscillator. this gives users the option of lower power consumption while still using a high accuracy clock source. sec_run mode is entered by setting the scs1:scs0 bits to ? 01 ?. the device clock source is switched to the timer1 oscillator (see figure 3-1), the primary oscillator is shut down, the t1run bit (t1con<6>) is set and the osts bit is cleared. on transitions from sec_run mode to pri_run, the peripherals and cpu continue to be clocked from the timer1 oscillator while the primary clock is started. when the primary clock becomes ready, a clock switch back to the primary clock occurs (see figure 3-2). when the clock switch is complete, the t1run bit is cleared, the osts bit is set and the primary clock provides the clock. the idlen and scs bits are not affected by the wake-up; the timer1 oscillator continues to run. note 1: caution should be used when modifying a single ircf bit. if v dd is less than 3v, it is possible to select a higher clock speed than is supported by the low v dd . improper device operation may result if the v dd /f osc specifications are violated. 2: executing a sleep instruction does not necessarily place the device into sleep mode. it acts as the trigger to place the controller into either the sleep mode or one of the idle modes, depending on the setting of the idlen bit. note: the timer1 oscillator should already be running prior to entering sec_run mode. if the t1oscen bit is not set when the scs1:scs0 bits are set to ? 01 ?, entry to sec_run mode will not occur. if the timer1 oscillator is enabled, but not yet running, peripheral clocks will be delayed until the oscillator has started. in such situations, initial oscillator operation is far from stable and unpredictable operation may result.
? 2004 microchip technology inc. preliminary ds39629b-page 43 PIC18F6390/6490/8390/8490 figure 3-1: transition timing for entry to sec_run mode figure 3-2: transition timing from sec_run mode to pri_run mode (hspll) q4 q3 q2 osc1 peripheral program q1 t1osi q1 counter clock cpu clock pc + 2 pc 123 n-1n clock transition q4 q3 q2 q1 q3 q2 pc + 4 q1 q3 q4 osc1 peripheral program pc t1osi pll clock q1 pc + 4 q2 output q3 q4 q1 cpu clock pc + 2 clock counter q2 q2 q3 note 1: t ost = 1024 t osc ; t pll = 2 ms (approx). these intervals are not shown to scale. scs1:scs0 bits changed t ost (1) t pll (1) 12 n-1 n clock osts bit set transition
PIC18F6390/6490/8390/8490 ds39629b-page 44 preliminary ? 2004 microchip technology inc. 3.2.3 rc_run mode in rc_run mode, the cpu and peripherals are clocked from the internal oscillator block using the intosc multiplexer and the primary clock is shut down. when using the intrc source, this mode provides the best power conservation of all the run modes, while still executing code. it works well for user applications which are not highly timing sensitive, or do not require high-speed clocks at all times. if the primary clock source is the internal oscillator block (either intrc or intosc), there are no distinguishable differences between pri_run and rc_run modes during execution. however, a clock switch delay will occur during entry to and exit from rc_run mode. therefore, if the primary clock source is the internal oscillator block, the use of rc_run mode is not recommended. this mode is entered by setting the scs1 bit to ? 1 ?. although it is ignored, it is recommended that the scs0 bit also be cleared; this is to maintain software compatibility with future devices. when the clock source is switched to the intosc multiplexer (see figure 3-3), the primary oscillator is shut down and the osts bit is cleared.the ircf bits may be modified at any time to immediately change the clock speed. if the ircf bits and the intsrc bit are all clear, the intosc output is not enabled and the iofs bit will remain clear; there will be no indication of the current clock source. the intrc source provides the device clocks. if the ircf bits are changed from all clear (thus enabling the intosc output), or if intsrc is set, the iofs bit becomes set after the intosc output becomes stable. clocks to the device continue while the intosc source stabilizes after an interval of t iobst . if the ircf bits were previously at a non-zero value, or if intsrc was set before setting scs1 and the intosc source was already stable, the iofs bit will remain set. on transitions from rc_run mode to pri_run, the device continues to be clocked from the intosc multiplexer while the primary clock is started. when the primary clock becomes ready, a clock switch to the primary clock occurs (see figure 3-4). when the clock switch is complete, the iofs bit is cleared, the osts bit is set and the primary clock provides the device clock. the idlen and scs bits are not affected by the switch. the intrc source will continue to run if either the wdt or the fail-safe clock monitor is enabled. figure 3-3: transition timing to rc_run mode figure 3-4: transition timing fr om rc_run mode to pri_run mode note: caution should be used when modifying a single ircf bit. if v dd is less than 3v, it is possible to select a higher clock speed than is supported by the low v dd . improper device operation may result if the v dd /f osc specifications are violated. q4 q3 q2 osc1 peripheral program q1 intrc q1 counter clock cpu clock pc + 2 pc 123 n-1n clock transition q4 q3 q2 q1 q3 q2 pc + 4 q1 q3 q4 osc1 peripheral program pc intosc pll clock q1 pc + 4 q2 output q3 q4 q1 cpu clock pc + 2 clock counter q2 q2 q3 note 1: t ost = 1024 t osc ; t pll = 2 ms (approx). these intervals are not shown to scale. scs1:scs0 bits changed t pll (1) 12 n-1n clock osts bit set transition multiplexer t ost (1)
? 2004 microchip technology inc. preliminary ds39629b-page 45 PIC18F6390/6490/8390/8490 3.3 sleep mode the power managed sleep mode in the PIC18F6390/6490/8390/8490 devices is identical to the legacy sleep mode offered in all other picmicro devices. it is entered by clearing the idlen bit (the default state on device reset) and executing the sleep instruction. this shuts down the selected oscillator (see figure 3-5). all clock source status bits are cleared. entering the sleep mode from any other mode does not require a clock switch. this is because no clocks are needed once the controller has entered sleep. if the wdt is selected, the intrc source will continue to operate. if the timer1 oscillator is enabled, it will also continue to run. when a wake event occurs in sleep mode (by interrupt, reset or wdt time-out), the device will not be clocked until the primary clock source becomes ready (see figure 3-6), or it will be clocked from the internal oscil- lator block if either the two-speed start-up or the fail-safe clock monitor are enabled (see section 23.0 ?special features of the cpu? ). in either case, the osts bit is set when the primary clock provides the device clocks. the idlen and scs bits are not affected by the wake-up. 3.4 idle modes the idle modes allow the controller?s cpu to be selectively shut down while the peripherals continue to operate. selecting a particular idle mode allows users to further manage power consumption. if the idlen bit is set to a ? 1 ? when a sleep instruction is executed, the peripherals will be clocked from the clock source selected using the scs1:scs0 bits; however, the cpu will not be clocked. the clock source status bits are not affected. setting idlen and execut- ing sleep provides a quick method of switching from a given run mode to its corresponding idle mode. if the wdt is selected, the intrc source will continue to operate. if the timer1 oscillator is enabled, it will also continue to run. since the cpu is not executing instructions, the only exits from any of the idle modes are by interrupt, wdt time-out or a reset. when a wake event occurs, cpu execution is delayed by an interval of t csd (parameter 38, table 26-10) while it becomes ready to execute code. when the cpu begins executing code, it resumes with the same clock source for the current idle mode. for example, when waking from rc_idle mode, the internal oscillator block will clock the cpu and peripherals (in other words, rc_run mode). the idlen and scs bits are not affected by the wake-up. while in any idle mode or the sleep mode, a wdt time-out will result in a wdt wake-up to the run mode currently specified by the scs1:scs0 bits. figure 3-5: transition timing for entry to sleep mode figure 3-6: transition timing for wake from sleep (hspll) q4 q3 q2 osc1 peripheral sleep program q1 q1 counter clock cpu clock pc + 2 pc q3 q4 q1 q2 osc1 peripheral program pc pll clock q3 q4 output cpu clock q1 q2 q3 q4 q1 q2 clock counter pc + 6 pc + 4 q1 q2 q3 q4 wake event note 1: t ost = 1024 t osc ; t pll = 2 ms (approx). these intervals are not shown to scale. t ost (1) t pll (1) osts bit set pc + 2
PIC18F6390/6490/8390/8490 ds39629b-page 46 preliminary ? 2004 microchip technology inc. 3.4.1 pri_idle mode this mode is unique among the three low-power idle modes, in that it does not disable the primary device clock. for timing sensitive applications, this allows for the fastest resumption of device operation with its more accurate primary clock source, since the clock source does not have to ?warm up? or transition from another oscillator. pri_idle mode is entered from pri_run mode by setting the idlen bit and executing a sleep instruc- tion. if the device is in another run mode, set idlen first, then clear the scs bits and execute sleep . although the cpu is disabled, the peripherals continue to be clocked from the primary clock source specified by the fosc3:fosc0 configuration bits. the osts bit remains set (see figure 3-7). when a wake event occurs, the cpu is clocked from the primary clock source. a delay of interval t csd is required between the wake event and when code execution starts. this is required to allow the cpu to become ready to execute instructions. after the wake-up, the osts bit remains set. the idlen and scs bits are not affected by the wake-up (see figure 3-8). figure 3-7: transition timing for entry to pri_idle mode figure 3-8: transition timing for wake from idle to run mode q1 peripheral program pc pc + 2 osc1 q3 q4 q1 cpu clock clock counter q2 osc1 peripheral program pc cpu clock q1 q3 q4 clock counter q2 wake event t csd
? 2004 microchip technology inc. preliminary ds39629b-page 47 PIC18F6390/6490/8390/8490 3.4.2 sec_idle mode in sec_idle mode, the cpu is disabled but the peripherals continue to be clocked from the timer1 oscillator. this mode is entered from sec_run by set- ting the idlen bit and executing a sleep instruction. if the device is in another run mode, set idlen first, then set scs1:scs0 to ? 01 ? and execute sleep . when the clock source is switched to the timer1 oscillator, the primary oscillator is shut down, the osts bit is cleared and the t1run bit is set. when a wake event occurs, the peripherals continue to be clocked from the timer1 oscillator. after an interval of t csd following the wake event, the cpu begins executing code being clocked by the timer1 oscillator. the idlen and scs bits are not affected by the wake-up; the timer1 oscillator continues to run (see figure 3-8). 3.4.3 rc_idle mode in rc_idle mode, the cpu is disabled but the periph- erals continue to be clocked from the internal oscillator block using the intosc multiplexer. this mode allows for controllable power conservation during idle periods. from rc_run, this mode is entered by setting the idlen bit and executing a sleep instruction. if the device is in another run mode, first set idlen, then set the scs1 bit and execute sleep . although its value is ignored, it is recommended that scs0 also be cleared; this is to maintain software compatibility with future devices. the intosc multiplexer may be used to select a higher clock frequency by modifying the ircf bits before executing the sleep instruction. when the clock source is switched to the intosc multiplexer, the primary oscillator is shut down and the osts bit is cleared. if the ircf bits are set to any non-zero value, or the intsrc bit is set, the intosc output is enabled. the iofs bit becomes set after the intosc output becomes stable after an interval of t iobst (parameter 39, table 26-10). clocks to the peripherals continue while the intosc source stabilizes. if the ircf bits were previously at a non-zero value, or intsrc was set before the sleep instruction was executed and the intosc source was already stable, the iofs bit will remain set. if the ircf bits and intsrc are all clear, the intosc output will not be enabled; the iofs bit will remain clear and there will be no indication of the current clock source. when a wake event occurs, the peripherals continue to be clocked from the intosc multiplexer. after a delay of t csd following the wake event, the cpu begins executing code being clocked by the intosc multi- plexer. the idlen and scs bits are not affected by the wake-up. the intrc source will continue to run if either the wdt or the fail-safe clock monitor is enabled. note: the timer1 oscillator should already be running prior to entering sec_idle mode. if the t1oscen bit is not set when the sleep instruction is executed, the sleep instruction will be ignored and entry to sec_idle mode will not occur. if the timer1 oscillator is enabled, but not yet running, peripheral clocks will be delayed until the oscillator has started. in such situations, initial oscillator operation is far from stable and unpredictable operation may result.
PIC18F6390/6490/8390/8490 ds39629b-page 48 preliminary ? 2004 microchip technology inc. 3.5 exiting idle and sleep modes an exit from sleep mode or any of the idle modes is triggered by an interrupt, a reset or a wdt time-out. this section discusses the triggers that cause exits from power managed modes. the clocking subsystem actions are discussed in each of the power managed modes (see section 3.2 ?run modes? through section 3.4 ?idle modes? ). 3.5.1 exit by interrupt any of the available interrupt sources can cause the device to exit from an idle or sleep mode to a run mode. to enable this functionality, an interrupt source must be enabled by setting its enable bit in one of the intcon or pie registers. the exit sequence is initiated when the corresponding interrupt flag bit is set. on all exits from idle or sleep modes by interrupt, code execution branches to the interrupt vector if the gie/gieh bit (intcon<7>) is set. otherwise, code execution continues or resumes without branching (see section 8.0 ?interrupts? ). a fixed delay of interval t csd , following the wake event, is required when leaving sleep and idle modes. this delay is required for the cpu to prepare for execution. instruction execution resumes on the first clock cycle following this delay. 3.5.2 exit by wdt time-out a wdt time-out will cause different actions depending on which power managed mode the device is in when the time-out occurs. if the device is not executing code (all idle modes and sleep mode), the time-out will result in an exit from the power managed mode (see section 3.2 ?run modes? and section 3.3 ?sleep mode? ). if the device is executing code (all run modes), the time-out will result in a wdt reset (see section 23.2 ?watchdog timer (wdt)? ). the wdt timer and postscaler are cleared by execut- ing a sleep or clrwdt instruction, losing a currently selected clock source (if the fail-safe clock monitor is enabled) and modifying the ircf bits in the osccon register if the internal oscillator block is the device clock source. 3.5.3 exit by reset normally, the device is held in reset by the oscillator start-up timer (ost) until the primary clock becomes ready. at that time, the osts bit is set and the device begins executing code. if the internal oscillator block is the new clock source, the iofs bit is set instead. the exit delay time from reset to the start of code execution depends on both the clock sources before and after the wake-up and the type of oscillator if the new clock source is the primary clock. exit delays are summarized in table 3-2. code execution can begin before the primary clock becomes ready. if either the two-speed start-up (see section 23.3 ?two-speed start-up? ) or fail-safe clock monitor (see section 23.4 ?fail-safe clock monitor? ) is enabled, the device may begin execution as soon as the reset source has cleared. execution is clocked by the intosc multiplexer driven by the internal oscillator block. execution is clocked by the internal oscillator block until either the primary clock becomes ready, or a power managed mode is entered before the primary clock becomes ready; the primary clock is then shut down. 3.5.4 exit without an oscillator start-up delay certain exits from power managed modes do not invoke the ost at all. there are two cases: pri_idle mode, where the primary clock source is not stopped; and the primary clock source is not any of the lp, xt, hs or hspll modes. in these instances, the primary clock source either does not require an oscillator start-up delay since it is already running (pri_idle), or normally does not require an oscillator start-up delay (rc, ec and intio oscillator modes). however, a fixed delay of interval t csd , following the wake event, is still required when leaving sleep and idle modes to allow the cpu to prepare for execution. instruction execution resumes on the first clock cycle following this delay.
? 2004 microchip technology inc. preliminary ds39629b-page 49 PIC18F6390/6490/8390/8490 table 3-2: exit delay on wake-up by reset from sleep mode or any idle mode (by clock sources) clock source before wake-up clock source after wake-up exit delay clock ready status bit (osccon) primary device clock (pri_idle mode) lp, xt, hs t csd (2) osts hspll ec, rc, intrc (1) ? intosc (3) iofs t1osc or intrc (1) lp, xt, hs t ost (4) osts hspll t ost + t rc (4) ec, rc, intrc (1) t csd (2) ? intosc (2) t iobst (5) iofs intosc (3) lp, xt, hs t ost (5) osts hspll t ost + t rc (4) ec, rc, intrc (1) t csd (2) ? intosc (2) none iofs none (sleep mode) lp, xt, hs t ost (4) osts hspll t ost + t rc (4) ec, rc, intrc (1) t csd (2) ? intosc (2) t iobst (5) iofs note 1: in this instance, refers specifically to the 31 khz intrc clock source. 2: t csd (parameter 38) is a required delay when waking from sleep and all idle modes and runs concurrently with any other required delays (see section 3.4 ?idle modes? ). 3: includes both the intosc 8 mhz source and postscaler derived frequencies. 4: t ost is the oscillator start-up timer (parameter 32). t rc is the pll lock-out timer (parameter f12); it is also designated as t pll . 5: execution continues during t iobst (parameter 39), the intosc stabilization period.
PIC18F6390/6490/8390/8490 ds39629b-page 50 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 51 PIC18F6390/6490/8390/8490 4.0 reset the PIC18F6390/6490/8390/8490 devices differentiate between various kinds of reset: a) power-on reset (por) b) mclr reset during normal operation c) mclr reset during power managed modes d) watchdog timer (wdt) reset (during execution) e) programmable brown-out reset (bor) f) reset instruction g) stack full reset h) stack underflow reset this section discusses resets generated by mclr , por and bor and covers the operation of the various start-up timers. stack reset events are covered in section 5.1.2.4 ?stack full and underflow resets? . wdt resets are covered in section 23.2 ?watchdog timer (wdt)? . a simplified block diagram of the on-chip reset circuit is shown in figure 4-1. 4.1 rcon register device reset events are tracked through the rcon register (register 4-1). the lower five bits of the register indicate that a specific reset event has occurred. in most cases, these bits can only be set by the event and must be cleared by the application after the event. the state of these flag bits, taken together, can be read to indicate the type of reset that just occurred. this is described in more detail in section 4.6 ?reset state of registers? . the rcon register also has control bits for setting interrupt priority (ipen) and software control of the bor (sboren). interrupt priority is discussed in section 8.0 ?interrupts? . bor is covered in section 4.4 ?brown-out reset (bor)? . figure 4-1: simplified block diagram of on-chip reset circuit s r q external reset mclr v dd osc1 wdt time-out v dd rise detect ost/pwrt intrc (1) por pulse ost 10-bit ripple counter pwrt chip_reset 11-bit ripple counter enable ost (2) enable pwrt note 1: this is the intrc source from the in ternal oscillator block and is separate from the rc oscillator of the clki pin. 2: see table 4-2 for time-out situations. brown-out reset boren reset instruction stack pointer stack full/underflow reset sleep ( )_idle 1024 cycles 65.5 ms 32 s mclre
PIC18F6390/6490/8390/8490 ds39629b-page 52 preliminary ? 2004 microchip technology inc. register 4-1: rcon: reset control re gister r/w-0 r/w-1 (1) u-0 r/w-1 r-1 r-1 r/w-0 r/w-0 ipen sboren ?ri to pd por bor bit 7 bit 0 bit 7 ipen: interrupt priority enable bit 1 = enable priority levels on interrupts 0 = disable priority levels on interrupts (pic16cxxx compatibility mode) bit 6 sboren: bor software enable bit if boren1:boren0 = 01 : 1 = bor is enabled 0 = bor is disabled if boren1:boren0 = 00 , 10 or 11 : bit is disabled and read as ? 0 ?. note 1: if sboren is enabled, its reset state is ? 1 ?; otherwise, it is ? 0 ?. bit 5 unimplemented: read as ? 0 ? bit 4 ri : reset instruction flag bit 1 = the reset instruction was not executed (set by firmware only) 0 = the reset instruction was executed causing a device reset (must be set in software after a brown-out reset occurs) bit 3 to : watchdog time-out flag bit 1 = set by power-up, clrwdt instruction or sleep instruction 0 = a wdt time-out occurred bit 2 pd : power-down detection flag bit 1 = set by power-up or by the clrwdt instruction 0 = set by execution of the sleep instruction bit 1 por : power-on reset status bit 1 = a power-on reset has not occurred (set by firmware only) 0 = a power-on reset occurred (must be set in software after a power-on reset occurs) bit 0 bor : brown-out reset status bit 1 = a brown-out reset has not occurred (set by firmware only) 0 = a brown-out reset occurred (must be set in software after a brown-out reset occurs) legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown note 1: it is recommended that the por bit be set after a power-on reset has been detected, so that subsequent power-on resets may be detected. 2: brown-out reset is said to have occurred when bor is ? 0 ? and por is ? 1 ? (assuming that por was set to ? 1 ? by software immediately after por).
? 2004 microchip technology inc. preliminary ds39629b-page 53 PIC18F6390/6490/8390/8490 4.2 master clear (mclr ) the mclr pin provides a method for triggering a hard external reset of the device. a reset is generated by holding the pin low. pic18 extended mcu devices have a noise filter in the mclr reset path which detects and ignores small pulses. the mclr pin is not driven low by any internal resets, including the wdt. in PIC18F6390/6490/8390/8490 devices, the mclr input can be disabled with the mclre configuration bit. when mclr is disabled, the pin becomes a digital input. see section 9.7 ?portg, trisg and latg registers? for more information. 4.3 power-on reset (por) a power-on reset pulse is generated on-chip whenever v dd rises above a certain threshold. this allows the device to start in the initialized state when v dd is adequate for operation. to take advantage of the por circuitry, tie the mclr pin through a resistor (1 k ? to 10 k ? ) to v dd . this will eliminate external rc components usually needed to create a power-on reset delay. a minimum rise rate for v dd is specified (parameter d004). for a slow rise time, see figure 4-2. when the device starts normal operation (i.e., exits the reset condition), device operating parameters (voltage, frequency, temperature, etc.) must be met to ensure operation. if these conditions are not met, the device must be held in reset until the operating conditions are met. por events are captured by the por bit (rcon<1>). the state of the bit is set to ? 0 ? whenever a por occurs; it does not change for any other reset event. por is not reset to ? 1 ? by any hardware event. to capture multiple events, the user manually resets the bit to ? 1 ? in software following any por. figure 4-2: external power-on reset circuit (for slow v dd power-up) note 1: external power-on reset circuit is required only if the v dd power-up slope is too slow. the diode d helps discharge the capacitor quickly when v dd powers down. 2: r < 40 k ? is recommended to make sure that the voltage drop across r does not violate the device?s electric al specification. 3: r1 1 k ? will limit any current flowing into mclr from external capacitor c, in the event of mclr /v pp pin breakdown, due to electrostatic discharge (esd) or electrical overstress (eos). c r1 r d v dd mclr pic18fxxxx v dd
PIC18F6390/6490/8390/8490 ds39629b-page 54 preliminary ? 2004 microchip technology inc. 4.4 brown-out reset (bor) PIC18F6390/6490/8390/8490 devices implement a bor circuit that provides the user with a number of configuration and power saving options. the bor is controlled by the borv1:borv0 and boren1:boren0 configuration bits. there are a total of four bor configurati ons, which are summarized in table 4-1. the bor threshold is set by the borv1:borv0 bits. if bor is enabled (any values of boren1:boren0 except ? 00 ?), any drop of v dd below v bor (parameter d005) for greater than t bor (parameter 35) will reset the device. a reset may or may not occur if v dd falls below v bor for less than t bor . the chip will remain in brown-out reset until v dd rises above v bor . if the power-up timer is enabled, it will be invoked after v dd rises above v bor ; it then will keep the chip in reset for an additional time delay, t pwrt (parameter 33). if v dd drops below v bor while the power-up timer is running, the chip will go back into a brown-out reset and the power-up timer will be initialized. once v dd rises above v bor , the power-up timer will execute the additional time delay. bor and the power-up timer (pwrt) are independently configured. enabling the bor reset does not automatically enable the pwrt. 4.4.1 software enabled bor when boren1:boren0 = 01 , the bor can be enabled or disabled by the user in software. this is done with the control bit, sboren (rcon<6>). setting sboren enables the bor to function as previously described. clearing sboren disables the bor entirely. the sboren bit operates only in this mode; otherwise it is read as ? 0 ?. placing the bor under software control gives the user the additional flexibility of tailoring the application to its environment without having to reprogram the device to change the bor configuration. it also allows the user to tailor device power consumption in software by eliminating the incremental current that the bor consumes. while the bor current is typically very small, it may have some impact in low-power applications. 4.4.2 detecting bor when bor is enabled, the bor bit always resets to ? 0 ? on any bor or por event. this makes it difficult to determine if a bor event has occurred just by reading the state of bor alone. a more reliable method is to simultaneously check the state of both por and bor . this assumes that the por bit is reset to ? 1 ? in software immediately after any por event. if bor is ? 0 ? while por is ? 1 ?, it can be reliably assumed that a bor event has occurred. 4.4.3 disabling bor in sleep mode when boren1:boren0 = 10 , the bor remains under hardware control and operates as previously described. whenever the device enters sleep mode, however, the bor is automatically disabled. when the device returns to any other operating mode, bor is automatically re-enabled. this mode allows for applications to recover from brown-out situations while actively executing code, when the device requires bor protection the most. at the same time, it saves additional power in sleep mode by eliminating the small incremental bor current. table 4-1: bor configurations note: even when bor is under software control, the bor reset voltage level is still set by the borv1:borv0 configuration bits. it cannot be changed in software. bor configuration status of sboren (rcon<6>) bor operation boren1 boren0 00 unavailable bor is disabled; must be enabled by reprogramming the configuration bits. 01 available bor is enabled in software; operation controlled by sboren. 10 unavailable bor is enabled in hardware and active during the run and idle modes, disabled during sleep mode. 11 unavailable bor is enabled in hardware; must be disabled by reprogramming the configuration bits.
? 2004 microchip technology inc. preliminary ds39629b-page 55 PIC18F6390/6490/8390/8490 4.5 device reset timers PIC18F6390/6490/8390/8490 devices incorporate three separate on-chip timers that help regulate the power-on reset process. their main function is to ensure that the device clock is stable before code is executed. these timers are: power-up timer (pwrt) oscillator start-up timer (ost) pll lock time-out 4.5.1 power-up timer (pwrt) the power-up timer (pwrt) of PIC18F6390/6490/8390/8490 devices is an 11-bit counter which uses the intrc source as the clock input. this yields an approximate time interval of 2048 x 32 s = 65.6 ms. while the pwrt is counting, the device is held in reset. the power-up time delay depends on the intrc clock and will vary from chip-to-chip due to temperature and process variation. see dc parameter 33 for details. the pwrt is enabled by clearing the pwrten configuration bit. 4.5.2 oscillator start-up timer (ost) the oscillator start-up timer (ost) provides a 1024 oscillator cycle (from osc1 input) delay after the pwrt delay is over (parameter 33). this ensures that the crystal oscillator or resonator has started and is stabilized. the ost time-out is invoked only for xt, lp, hs and hspll modes and only on power-on reset, or on exit from most power managed modes. 4.5.3 pll lock time-out with the pll enabled in its pll mode, the time-out sequence following a power-on reset is slightly different from other oscillator modes. a separate timer is used to provide a fixed time-out that is sufficient for the pll to lock to the main oscillator frequency. this pll lock time-out (t pll ) is typically 2 ms and follows the oscillator start-up time-out. 4.5.4 time-out sequence on power-up, the time-out sequence is as follows: 1. after the por pulse has cleared, pwrt time-out is invoked (if enabled). 2. then, the ost is activated. the total time-out will vary based on oscillator configuration and the status of the pwrt. figure 4-3, figure 4-4, figure 4-5, figure 4-6 and figure 4-7 all depict time-out sequences on power-up, with the power-up timer enabled and the device operating in hs oscillator mode. figures 4-3 through 4-6 also apply to devices operating in xt or lp modes. for devices in rc mode and with the pwrt disabled, on the other hand, there will be no time-out at all. since the time-outs occur from the por pulse, if mclr is kept low long enough, all time-outs will expire. bringing mclr high will begin execution immediately (figure 4-5). this is useful for testing purposes, or to synchronize more than one pic18fxxxx device operating in parallel. table 4-2: time-out in various situations oscillator configuration power-up (2) and brown-out exit from power managed mode pwrten = 0 pwrten = 1 hspll 66 ms (1) + 1024 t osc + 2 ms (2) 1024 t osc + 2 ms (2) 1024 t osc + 2 ms (2) hs, xt, lp 66 ms (1) + 1024 t osc 1024 t osc 1024 t osc ec, ecio 66 ms (1) ?? rc, rcio 66 ms (1) ?? intio1, intio2 66 ms (1) ?? note 1: 66 ms (65.5 ms) is the nominal power-up timer (pwrt) delay. 2: 2 ms is the nominal time required for the pll to lock.
PIC18F6390/6490/8390/8490 ds39629b-page 56 preliminary ? 2004 microchip technology inc. figure 4-3: time-out sequence on power-up (mclr tied to v dd , v dd rise < t pwrt ) figure 4-4: time-out sequence on power-up (mclr not tied to v dd ): case 1 figure 4-5: time-out sequence on power-up (mclr not tied to v dd ): case 2 t pwrt t ost v dd mclr internal por pwrt time-out ost time-out internal reset t pwrt t ost v dd mclr internal por pwrt time-out ost time-out internal reset v dd mclr internal por pwrt time-out ost time-out internal reset t pwrt t ost
? 2004 microchip technology inc. preliminary ds39629b-page 57 PIC18F6390/6490/8390/8490 figure 4-6: slow rise time (mclr tied to v dd , v dd rise > t pwrt ) figure 4-7: time-out sequence on por w/pll enabled (mclr tied to v dd ) v dd mclr internal por pwrt time-out ost time-out internal reset 0v 1v 5v t pwrt t ost t pwrt t ost v dd mclr internal por pwrt time-out ost time-out internal reset pll time-out t pll note: t ost = 1024 clock cycles. t pll 2 ms max. first three stages of the pwrt timer.
PIC18F6390/6490/8390/8490 ds39629b-page 58 preliminary ? 2004 microchip technology inc. 4.6 reset state of registers most registers are unaffected by a reset. their status is unknown on por and unchanged by all other resets. the other registers are forced to a ?reset state? depending on the type of reset that occurred. most registers are not affected by a wdt wake-up, since this is viewed as the resumption of normal operation. status bits from the rcon register, ri , to , pd , por and bor, are set or cleared differently in different reset situations, as indicated in table 4-3. these bits are used in software to determine the nature of the reset. table 4-4 describes the reset states for all of the special function registers. these are categorized by power-on and brown-out resets, master clear and wdt resets and wdt wake-ups. table 4-3: status bits, their significance and the initialization condition for rcon register condition program counter rcon register stkptr register sboren ri to pd por bor stkful stkunf power-on reset 0000h 1 11100 0 0 reset instruction 0000h u (2) 0uuuu u u brown-out reset 0000h u (2) 111u0 u u mclr reset during power managed run modes 0000h u (2) u1uuu u u mclr reset during power managed idle modes and sleep 0000h u (2) u10uu u u wdt time-out during full power or power managed run modes 0000h u (2) u0uuu u u mclr during full power execution 0000h u (2) uuuuu u u stack full reset (stvren = 1 ) 0000h u (2) uuuuu 1 u stack underflow reset (stvren = 1 ) 0000h u (2) uuuuu u 1 stack underflow error (not an actual reset, stvren = 0 ) 0000h u (2) uuuuu u 1 wdt time-out during power managed idle or sleep modes pc + 2 (1) u (2) u00uu u u interrupt exit from power managed modes pc + 2 (1) u (2) uu0uu u u legend: u = unchanged note 1: when the wake-up is due to an interrupt and the gieh or giel bits are set, the pc is loaded with the interrupt vector (008h or 0018h). 2: reset state is ? 1 ? for por and unchanged for all other resets when software bor is enabled (boren1:boren0 configuration bits = 01 and sboren = 1 ). otherwise, the reset state is ? 0 ?.
? 2004 microchip technology inc. preliminary ds39629b-page 59 PIC18F6390/6490/8390/8490 table 4-4: initialization conditions for all registers register applicable devices power-on reset, brown-out reset mclr resets wdt reset reset instruction stack resets wake-up via wdt or interrupt tosu 6x90 8x90 ---0 0000 ---0 0000 ---0 uuuu (3) tosh 6x90 8x90 0000 0000 0000 0000 uuuu uuuu (3) tosl 6x90 8x90 0000 0000 0000 0000 uuuu uuuu (3) stkptr 6x90 8x90 uu-0 0000 00-0 0000 uu-u uuuu (3) pclatu 6x90 8x90 ---0 0000 ---0 0000 ---u uuuu pclath 6x90 8x90 0000 0000 0000 0000 uuuu uuuu pcl 6x90 8x90 0000 0000 0000 0000 pc + 2 (2) tblptru 6x90 8x90 --00 0000 --00 0000 --uu uuuu tblptrh 6x90 8x90 0000 0000 0000 0000 uuuu uuuu tblptrl 6x90 8x90 0000 0000 0000 0000 uuuu uuuu tablat 6x90 8x90 0000 0000 0000 0000 uuuu uuuu prodh 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu prodl 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu intcon 6x90 8x90 0000 000x 0000 000u uuuu uuuu (1) intcon2 6x90 8x90 1111 1111 1111 1111 uuuu uuuu (1) intcon3 6x90 8x90 1100 0000 1100 0000 uuuu uuuu (1) indf0 6x90 8x90 n/a n/a n/a postinc0 6x90 8x90 n/a n/a n/a postdec0 6x90 8x90 n/a n/a n/a preinc0 6x90 8x90 n/a n/a n/a plusw0 6x90 8x90 n/a n/a n/a fsr0h 6x90 8x90 ---- xxxx ---- uuuu ---- uuuu fsr0l 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu wreg 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu indf1 6x90 8x90 n/a n/a n/a postinc1 6x90 8x90 n/a n/a n/a postdec1 6x90 8x90 n/a n/a n/a preinc1 6x90 8x90 n/a n/a n/a plusw1 6x90 8x90 n/a n/a n/a legend: u = unchanged, x = unknown, - = unimplemented bit, read as ? 0 ?, q = value depends on condition. shaded cells indicate conditions do not apply for the designated device. note 1: one or more bits in the intconx or pirx registers will be affected (to cause wake-up). 2: when the wake-up is due to an interrupt and the giel or gieh bit is set, the pc is loaded with the interrupt vector (0008h or 0018h). 3: when the wake-up is due to an interrupt and the giel or gieh bit is set, the tosu, tosh and tosl are updated with the current value of the pc. the stkptr is modified to point to the next location in the hardware stack. 4: see table 4-3 for reset value for specific condition. 5: bits 6 and 7 of porta, lata and trisa are enabled depending on the oscillator mode selected. when not enabled as porta pins, they are disabled and read ? 0 ?.
PIC18F6390/6490/8390/8490 ds39629b-page 60 preliminary ? 2004 microchip technology inc. fsr1h 6x90 8x90 ---- xxxx ---- uuuu ---- uuuu fsr1l 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu bsr 6x90 8x90 ---- 0000 ---- 0000 ---- uuuu indf2 6x90 8x90 n/a n/a n/a postinc2 6x90 8x90 n/a n/a n/a postdec2 6x90 8x90 n/a n/a n/a preinc2 6x90 8x90 n/a n/a n/a plusw2 6x90 8x90 n/a n/a n/a fsr2h 6x90 8x90 ---- xxxx ---- uuuu ---- uuuu fsr2l 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu status 6x90 8x90 ---x xxxx ---u uuuu ---u uuuu tmr0h 6x90 8x90 0000 0000 0000 0000 uuuu uuuu tmr0l 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu t0con 6x90 8x90 1111 1111 1111 1111 uuuu uuuu osccon 6x90 8x90 0100 q000 0100 00q0 uuuu uuqu hlvdcon 6x90 8x90 0-00 0101 0-00 0101 u-uu uuuu wdtcon 6x90 8x90 ---- ---0 ---- ---0 ---- ---u rcon (4) 6x90 8x90 0q-1 11q0 0q-q qquu uq-u qquu tmr1h 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu tmr1l 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu t1con 6x90 8x90 0000 0000 u0uu uuuu uuuu uuuu tmr2 6x90 8x90 0000 0000 0000 0000 uuuu uuuu pr2 6x90 8x90 1111 1111 1111 1111 1111 1111 t2con 6x90 8x90 -000 0000 -000 0000 -uuu uuuu sspbuf 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu sspadd 6x90 8x90 0000 0000 0000 0000 uuuu uuuu sspstat 6x90 8x90 0000 0000 0000 0000 uuuu uuuu sspcon1 6x90 8x90 0000 0000 0000 0000 uuuu uuuu sspcon2 6x90 8x90 0000 0000 0000 0000 uuuu uuuu table 4-4: initialization conditi ons for all registers (continued) register applicable devices power-on reset, brown-out reset mclr resets wdt reset reset instruction stack resets wake-up via wdt or interrupt legend: u = unchanged, x = unknown, - = unimplemented bit, read as ? 0 ?, q = value depends on condition. shaded cells indicate conditions do not apply for the designated device. note 1: one or more bits in the intconx or pirx registers will be affected (to cause wake-up). 2: when the wake-up is due to an interrupt and the giel or gieh bit is set, the pc is loaded with the interrupt vector (0008h or 0018h). 3: when the wake-up is due to an interrupt and the giel or gieh bit is set, the tosu, tosh and tosl are updated with the current value of the pc. the stkptr is modified to point to the next location in the hardware stack. 4: see table 4-3 for reset value for specific condition. 5: bits 6 and 7 of porta, lata and trisa are enabled depending on the oscillator mode selected. when not enabled as porta pins, they are disabled and read ? 0 ?.
? 2004 microchip technology inc. preliminary ds39629b-page 61 PIC18F6390/6490/8390/8490 adresh 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu adresl 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu adcon0 6x90 8x90 --00 0000 --00 0000 --uu uuuu adcon1 6x90 8x90 --00 0000 --00 0000 --uu uuuu adcon2 6x90 8x90 0-00 0000 0-00 0000 u-uu uuuu ccpr1h 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu ccpr1l 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu ccp1con 6x90 8x90 --00 0000 --00 0000 --uu uuuu ccpr2h 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu ccpr2l 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu ccp2con 6x90 8x90 --00 0000 --00 0000 --uu uuuu cvrcon 6x90 8x90 000- 0000 000- 0000 uuu- uuuu cmcon 6x90 8x90 0000 0111 0000 0111 uuuu uuuu tmr3h 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu tmr3l 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu t3con 6x90 8x90 0000 0000 uuuu uuuu uuuu uuuu spbrg1 6x90 8x90 0000 0000 0000 0000 uuuu uuuu rcreg1 6x90 8x90 0000 0000 0000 0000 uuuu uuuu txreg1 6x90 8x90 0000 0000 0000 0000 uuuu uuuu txsta1 6x90 8x90 0000 0010 0000 0010 uuuu uuuu rcsta1 6x90 8x90 0000 000x 0000 000x uuuu uuuu ipr3 6x90 8x90 -111 ---- -111 ---- -uuu ---- pir3 6x90 8x90 -000 ---- -000 ---- -uuu ---- (1) pie3 6x90 8x90 -000 ---- -000 ---- -uuu ---- ipr2 6x90 8x90 11-- 1111 11-- 1111 uu-- uuuu pir2 6x90 8x90 00-- 0000 00-- 0000 uu-- uuuu (1) pie2 6x90 8x90 00-- 0000 00-- 0000 uu-- uuuu ipr1 6x90 8x90 -111 1111 -111 1111 -uuu uuuu pir1 6x90 8x90 -000 0000 -000 0000 -uuu uuuu (1) pie1 6x90 8x90 -000 0000 -000 0000 -uuu uuuu osctune 6x90 8x90 00-0 0000 00-0 0000 uu-u uuuu table 4-4: initialization conditions for all registers (continued) register applicable devices power-on reset, brown-out reset mclr resets wdt reset reset instruction stack resets wake-up via wdt or interrupt legend: u = unchanged, x = unknown, - = unimplemented bit, read as ? 0 ?, q = value depends on condition. shaded cells indicate conditions do not apply for the designated device. note 1: one or more bits in the intconx or pirx registers will be affected (to cause wake-up). 2: when the wake-up is due to an interrupt and the giel or gieh bit is set, the pc is loaded with the interrupt vector (0008h or 0018h). 3: when the wake-up is due to an interrupt and the giel or gieh bit is set, the tosu, tosh and tosl are updated with the current value of the pc. the stkptr is modified to point to the next location in the hardware stack. 4: see table 4-3 for reset value for specific condition. 5: bits 6 and 7 of porta, lata and trisa are enabled depending on the oscillator mode selected. when not enabled as porta pins, they are disabled and read ? 0 ?.
PIC18F6390/6490/8390/8490 ds39629b-page 62 preliminary ? 2004 microchip technology inc. trisj 6x90 8x90 1111 1111 1111 1111 uuuu uuuu trish 6x90 8x90 1111 1111 1111 1111 uuuu uuuu trisg 6x90 8x90 ---1 1111 ---1 1111 ---u uuuu trisf 6x90 8x90 1111 1111 1111 1111 uuuu uuuu trise 6x90 8x90 1111 ---- 1111 ---- uuuu ---- trisd 6x90 8x90 1111 1111 1111 1111 uuuu uuuu trisc 6x90 8x90 1111 1111 1111 1111 uuuu uuuu trisb 6x90 8x90 1111 1111 1111 1111 uuuu uuuu trisa (5) 6x90 8x90 1111 1111 (5) 1111 1111 (5) uuuu uuuu (5) latj 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lath 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu latg 6x90 8x90 ---x xxxx ---u uuuu ---u uuuu latf 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu late 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu latd 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu latc 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu latb 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lata (5) 6x90 8x90 xxxx xxxx (5) uuuu uuuu (5) uuuu uuuu (5) portj 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu porth 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu portg 6x90 8x90 --xx xxxx --uu uuuu --uu uuuu portf 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu porte 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu portd 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu portc 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu portb 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu porta (5) 6x90 8x90 xx0x 0000 (5) uu0u 0000 (5) uuuu uuuu (5) spbrgh1 6x90 8x90 0000 0000 0000 0000 uuuu uuuu baudcon1 6x90 8x90 01-0 0-00 01-0 0-00 uu-u u-uu table 4-4: initialization conditi ons for all registers (continued) register applicable devices power-on reset, brown-out reset mclr resets wdt reset reset instruction stack resets wake-up via wdt or interrupt legend: u = unchanged, x = unknown, - = unimplemented bit, read as ? 0 ?, q = value depends on condition. shaded cells indicate conditions do not apply for the designated device. note 1: one or more bits in the intconx or pirx registers will be affected (to cause wake-up). 2: when the wake-up is due to an interrupt and the giel or gieh bit is set, the pc is loaded with the interrupt vector (0008h or 0018h). 3: when the wake-up is due to an interrupt and the giel or gieh bit is set, the tosu, tosh and tosl are updated with the current value of the pc. the stkptr is modified to point to the next location in the hardware stack. 4: see table 4-3 for reset value for specific condition. 5: bits 6 and 7 of porta, lata and trisa are enabled depending on the oscillator mode selected. when not enabled as porta pins, they are disabled and read ? 0 ?.
? 2004 microchip technology inc. preliminary ds39629b-page 63 PIC18F6390/6490/8390/8490 lcddata23 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata22 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata21 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata20 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata19 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata18 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata17 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata16 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata15 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata14 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata13 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata12 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata11 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu spbrg2 6x90 8x90 0000 0000 0000 0000 uuuu uuuu rcreg2 6x90 8x90 0000 0000 0000 0000 uuuu uuuu txreg2 6x90 8x90 0000 0000 0000 0000 uuuu uuuu txsta2 6x90 8x90 0000 0010 0000 0010 uuuu uuuu rcsta2 6x90 8x90 0000 000x 0000 000x uuuu uuuu lcddata10 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata9 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata8 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata7 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata6 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata5 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata4 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata3 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata2 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata1 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu lcddata0 6x90 8x90 xxxx xxxx uuuu uuuu uuuu uuuu table 4-4: initialization conditions for all registers (continued) register applicable devices power-on reset, brown-out reset mclr resets wdt reset reset instruction stack resets wake-up via wdt or interrupt legend: u = unchanged, x = unknown, - = unimplemented bit, read as ? 0 ?, q = value depends on condition. shaded cells indicate conditions do not apply for the designated device. note 1: one or more bits in the intconx or pirx registers will be affected (to cause wake-up). 2: when the wake-up is due to an interrupt and the giel or gieh bit is set, the pc is loaded with the interrupt vector (0008h or 0018h). 3: when the wake-up is due to an interrupt and the giel or gieh bit is set, the tosu, tosh and tosl are updated with the current value of the pc. the stkptr is modified to point to the next location in the hardware stack. 4: see table 4-3 for reset value for specific condition. 5: bits 6 and 7 of porta, lata and trisa are enabled depending on the oscillator mode selected. when not enabled as porta pins, they are disabled and read ? 0 ?.
PIC18F6390/6490/8390/8490 ds39629b-page 64 preliminary ? 2004 microchip technology inc. lcdse5 6x90 8x90 0000 0000 uuuu uuuu uuuu uuuu lcdse4 6x90 8x90 0000 0000 uuuu uuuu uuuu uuuu lcdse3 6x90 8x90 0000 0000 uuuu uuuu uuuu uuuu lcdse2 6x90 8x90 0000 0000 uuuu uuuu uuuu uuuu lcdse1 6x90 8x90 0000 0000 uuuu uuuu uuuu uuuu lcdse0 6x90 8x90 0000 0000 uuuu uuuu uuuu uuuu lcdcon 6x90 8x90 000- 0000 000- 0000 uuu- uuuu lcdps 6x90 8x90 0000 0000 0000 0000 uuuu uuuu table 4-4: initialization conditi ons for all registers (continued) register applicable devices power-on reset, brown-out reset mclr resets wdt reset reset instruction stack resets wake-up via wdt or interrupt legend: u = unchanged, x = unknown, - = unimplemented bit, read as ? 0 ?, q = value depends on condition. shaded cells indicate conditions do not apply for the designated device. note 1: one or more bits in the intconx or pirx registers will be affected (to cause wake-up). 2: when the wake-up is due to an interrupt and the giel or gieh bit is set, the pc is loaded with the interrupt vector (0008h or 0018h). 3: when the wake-up is due to an interrupt and the giel or gieh bit is set, the tosu, tosh and tosl are updated with the current value of the pc. the stkptr is modified to point to the next location in the hardware stack. 4: see table 4-3 for reset value for specific condition. 5: bits 6 and 7 of porta, lata and trisa are enabled depending on the oscillator mode selected. when not enabled as porta pins, they are disabled and read ? 0 ?.
? 2004 microchip technology inc. preliminary ds39629b-page 65 PIC18F6390/6490/8390/8490 5.0 memory organization there are two types of memory in pic18 flash microcontroller devices: program memory data ram as harvard architecture devices, the data and program memories use separate busses; this allows for concurrent access of the two memory spaces. additional detailed information on the operation of the flash program memory is provided in section 6.0 ?flash program memory? . 5.1 program memory organization pic18 microcontrollers implement a 21-bit program counter, which is capable of addressing a 2-mbyte program memory space. accessing a location between the upper boundary of the physically implemented memory and the 2-mbyte address will return all ? 0 ?s (a nop instruction). the pic18fx390 have 8 kbytes of flash memory and can store up to 4,096 single-word instructions and pic18fx490 have 16 kbytes of flash memory and can store up to 8,192 single-word instructions. pic18 devices have two interrupt vectors. the reset vector address is at 0000h and the interrupt vector addresses are at 0008h and 0018h. the program memory maps for PIC18F6390/6490/8390/8490 devices are shown in figure 5-1. figure 5-1: program memory map and stack for PIC18F6390/6490/8390/8490 devices pc<20:0> stack level 1 ? stack level 31 reset vector low priority interrupt vector ? ? call,rcall,return retfie,retlw 21 0000h 0018h on-chip program memory high priority interrupt vector 0008h user memory space 1fffffh 2000h 1fffh read ? 0 ? pc<20:0> stack level 1 ? stack level 31 reset vector low priority interrupt vector ? ? call,rcall,return retfie,retlw 21 0000h 0018h on-chip program memory high priority interrupt vector 0008h user memory space 1fffffh 4000h 3fffh read ? 0 ? PIC18F6390/8390 pic18f6490/8490
PIC18F6390/6490/8390/8490 ds39629b-page 66 preliminary ? 2004 microchip technology inc. 5.1.1 program counter the program counter (pc) specifies the address of the instruction to fetch for execution. the pc is 21 bits wide and is contained in three separate 8-bit registers. the low byte, known as the pcl register, is both readable and writable. the high byte, or pch register, contains the pc<15:8> bits; it is not directly readable or writable. updates to the pch register are performed through the pclath register. the upper byte is called pcu. this register contains the pc<20:16> bits; it is also not directly readable or writable. updates to the pcu register are performed through the pclatu register. the contents of pclath and pclatu are transferred to the program counter by any operation that writes pcl. similarly, the upper two bytes of the program counter are transferred to pclath and pclatu by an operation that reads pcl. this is useful for computed offsets to the pc (see section 5.1.4.1 ?computed goto? ). the pc addresses bytes in the program memory. to prevent the pc from becoming misaligned with word instructions, the least significant bit of pcl is fixed to a value of ? 0 ?. the pc increments by 2 to address sequential instructions in the program memory. the call, rcall, goto and program branch instructions write to the program counter directly. for these instructions, the contents of pclath and pclatu are not transferred to the program counter. 5.1.2 return address stack the return address stack allows any combination of up to 31 program calls and interrupts to occur. the pc is pushed onto the stack when a call or rcall instruc- tion is executed, or an interrupt is acknowledged. the pc value is pulled off the stack on a return, retlw or a retfie instruction. pclatu and pclath are not affected by any of the return or call instructions. the stack operates as a 31-word by 21-bit ram and a 5-bit stack pointer. the stack space is not part of either program or data space. the stack pointer is readable and writable and the address on the top of the stack is readable and writable through the top-of-stack special file registers. data can also be pushed to, or popped from the stack using these registers. a call type instruction causes a push onto the stack; the stack pointer is first incremented and the location pointed to by the stack pointer is written with the contents of the pc (already pointing to the instruction following the call ). a return type instruction causes a pop from the stack; the contents of the location pointed to by the stkptr register are transferred to the pc and then the stack pointer is decremented. the stack pointer is initialized to ? 00000 ? after all resets. there is no ram associated with the location corresponding to a stack pointer value of ? 00000 ?; this is only a reset value. status bits indicate if the stack is full, has overflowed or has underflowed. 5.1.2.1 top-of-stack access only the top of the return address stack (tos) is read- able and writable. a set of three registers, tosu:tosh:tosl, hold the contents of the stack location pointed to by the lower five bits of the stkptr register (figure 5-2). this allows users to implement a software stack if necessary. after a call, rcall or interrupt, the software can read the pushed value by reading the tosu:tosh:tosl registers. these values can be placed on a user defined software stack. at return time, the software can return these values to tosu:tosh:tosl and do a return. the user must disable the global interrupt enable bits while accessing the stack to prevent inadvertent stack corruption. figure 5-2: return address stack and associated registers 00011 001a34h 11111 11110 11101 00010 00001 00000 00010 return address stack <20:0> to p - o f - st a c k 000d58h tosl tosh tosu 34h 1ah 00h stkptr<4:0> top-of-stack registers stack pointer
? 2004 microchip technology inc. preliminary ds39629b-page 67 PIC18F6390/6490/8390/8490 5.1.2.2 return stack pointer (stkptr) the stkptr register (register 5-1) contains the stack pointer value, the stkful (stack full) status bit and the stkunf (stack underflow) status bits. the value of the stack pointer can be 0 through 31. the stack pointer increments before values are pushed onto the stack and decrements after values are popped off the stack. on reset, the stack pointer value will be zero. the user may read and write the stack pointer value. this feature can be used by a real-time operating system for return stack maintenance. after the pc is pushed onto the stack 31 times (without popping any values off the stack), the stkful bit is set. the stkful bit is cleared by software or by a por. the action that takes place when the stack becomes full depends on the state of the stvren (stack over- flow reset enable) configuration bit. (refer to section 23.1 ?configuration bits? for a description of the device configuration bits.) if stvren is set (default), the 31st push will push the (pc + 2) value onto the stack, set the stkful bit and reset the device. the stkful bit will remain set and the stack pointer will be set to zero. if stvren is cleared, the stkful bit will be set on the 31st push and the stack pointer will increment to 31. any additional pushes will not overwrite the 31st push and stkptr will remain at 31. when the stack has been popped enough times to unload the stack, the next pop will return a value of zero to the pc and sets the stkunf bit, while the stack pointer remains at zero. the stkunf bit will remain set until cleared by software, or until a por occurs. 5.1.2.3 push and pop instructions since the top-of-stack is readable and writable, the ability to push values onto the stack and pull values off the stack, without disturbing normal program execu- tion, is a desirable feature. the pic18 instruction set includes two instructions, push and pop , that permit the tos to be manipulated under software control. tosu, tosh and tosl can be modified to place data or a return address on the stack. the push instruction places the current pc value onto the stack. this increments the stack pointer and loads the current pc value onto the stack. the pop instruction discards the current tos by decrementing the stack pointer. the previous value pushed onto the stack then becomes the tos value. register 5-1: stkptr: stack pointer register note: returning a value of zero to the pc on an underflow has the effect of vectoring the program to the reset vector where the stack conditions can be verified and appropriate actions can be taken. this is not the same as a reset, as the contents of the sfrs are not affected. r/c-0 r/c-0 u-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 stkful (1) stkunf (1) ? sp4 sp3 sp2 sp1 sp0 bit 7 bit 0 bit 7 stkful: stack full flag bit (1) 1 = stack became full or overflowed 0 = stack has not become full or overflowed bit 6 (1) stkunf: stack underflow flag bit (1) 1 = stack underflow occurred 0 = stack underflow did not occur bit 5 unimplemented: read as ? 0 ? bit 4-0 sp4:sp0: stack pointer location bits note 1: bit 7 and bit 6 are cleared by user software or by a por. legend: r = readable bit w = writable bit u = unimplemented c = clearable only bit -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 68 preliminary ? 2004 microchip technology inc. 5.1.2.4 stack full and underflow resets device resets on stack overflow and stack underflow conditions are enabled by setting the stvren bit in configuration register 4l. when stvren is set, a full or underflow will set the appropriate stkful or stkunf bit and then cause a device reset. when stvren is cleared, a full or underflow condition will set the appropriate stkful or stkunf bit, but not cause a device reset. the stkful or stkunf bits are cleared by the user software or a power-on reset. 5.1.3 fast register stack a fast register stack is provided for the status, wreg and bsr registers, to provide a ?fast return? option for interrupts. this stack is only one level deep and is neither readable nor writable. it is loaded with the current value of the corresponding register when the processor vectors for an interrupt. all interrupt sources will push values into the stack registers. the values in the registers are then loaded back into the working registers if the retfie, fast instruction is used to return from the interrupt. if both low and high priority interrupts are enabled, the stack registers cannot be used reliably to return from low priority interrupts. if a high priority interrupt occurs while servicing a low priority interrupt, the stack register values stored by the low priority interrupt will be overwritten. in these cases, users must save the key registers in software during a low priority interrupt. if interrupt priority is not used, all interrupts may use the fast register stack for returns from interrupt. if no interrupts are used, the fast register stack can be used to restore the status, wreg and bsr registers at the end of a subroutine call. to use the fast register stack for a subroutine call, a call label, fast instruction must be executed to save the status, wreg and bsr registers to the fast register stack. a return, fast instruction is then executed to restore these registers from the fast register stack. example 5-1 shows a source code example that uses the fast register stack during a subroutine call and return. example 5-1: fast register stack code example 5.1.4 look-up tables in program memory there may be programming situations that require the creation of data structures, or look-up tables, in program memory. for pic18 devices, look-up tables can be implemented in two ways: computed goto table reads 5.1.4.1 computed goto a computed goto is accomplished by adding an offset to the program counter. an example is shown in example 5-2. a look-up table can be formed with an addwf pcl instruction and a group of retlw nn instructions. the w register is loaded with an offset into the table before executing a call to that table. the first instruction of the called routine is the addwf pcl instruction. the next instruction executed will be one of the retlw nn instructions that returns the value ? nn ? to the calling function. the offset value (in wreg) specifies the number of bytes that the program counter should advance and should be multiples of 2 (lsb = 0 ). in this method, only one data byte may be stored in each instruction location and room on the return address stack is required. example 5-2: computed goto using an offset value 5.1.4.2 table reads a better method of storing data in program memory allows two bytes of data to be stored in each instruction location. look-up table data may be stored two bytes per program word while programming. the table pointer register (tblptr) specifies the byte address and the table latch register (tablat) contains the data that is read from the program memory. data is transferred from program memory one byte at a time. table read operation is discussed further in section 6.1 ?table reads? . call sub1, fast ;status, wreg, bsr ;saved in fast register ;stack ? ? sub1 ? ? return fast ;restore values saved ;in fast register stack movf offset, w call table org nn00h table addwf pcl retlw nnh retlw nnh retlw nnh . . .
? 2004 microchip technology inc. preliminary ds39629b-page 69 PIC18F6390/6490/8390/8490 5.2 pic18 instruction cycle 5.2.1 clocking scheme the microcontroller clock input, whether from an internal or external source, is internally divided by four to generate four non-overlapping quadrature clocks (q1, q2, q3 and q4). internally, the program counter is incremented on every q1; the instruction is fetched from the program memory and latched into the instruc- tion register (ir) during q4. the instruction is decoded and executed during the following q1 through q4. the clocks and instruction execution flow are shown in figure 5-3. 5.2.2 instruction flow/pipelining an ?instruction cycle? consists of four q cycles, q1 through q4. the instruction fetch and execute are pipe- lined in such a manner that a fetch takes one instruction cycle, while the decode and execute take another instruction cycle. however, due to the pipelining, each instruction effectively executes in one cycle. if an instruction causes the program counter to change (e.g., goto ), then two cycles are required to complete the instruction (example 5-3). a fetch cycle begins with the program counter (pc) incrementing in q1. in the execution cycle, the fetched instruction is latched into the instruction register (ir) in cycle q1. this instruction is then decoded and executed during the q2, q3 and q4 cycles. data memory is read during q2 (operand read) and written during q4 (destination write). figure 5-3: clock/ instruction cycle example 5-3: instruction pipeline flow q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 osc1 q1 q2 q3 q4 pc osc2/clko (rc mode) pc pc + 2 pc + 4 fetch inst (pc) execute inst (pc ? 2) fetch inst (pc + 2) execute inst (pc) fetch inst (pc + 4) execute inst (pc + 2) internal phase clock all instructions are single cycle, except for any program branches. these take two cycles since the fetch instruction is ?flushed? from the pipeline, while the new instruction is being fetched and then executed. t cy 0t cy 1t cy 2t cy 3t cy 4t cy 5 1. movlw 55h fetch 1 execute 1 2. movwf portb fetch 2 execute 2 3. bra sub_1 fetch 3 execute 3 4. bsf porta, bit3 (forced nop) fetch 4 flush ( nop ) 5. instruction @ address sub_1 fetch sub_1 execute sub_1
PIC18F6390/6490/8390/8490 ds39629b-page 70 preliminary ? 2004 microchip technology inc. 5.2.3 instructions in program memory the program memory is addressed in bytes. instruc- tions are stored as two bytes or four bytes in program memory. the least significant byte of an instruction word is always stored in a program memory location with an even address (lsb = 0 ). to maintain alignment with instruction boundaries, the pc increments in steps of 2 and the lsb will always read ? 0 ? (see section 5.1.1 ?program counter? ). figure 5-4 shows an example of how instruction words are stored in the program memory. the call and goto instructions have the absolute pro- gram memory address embedded into the instruction. since instructions are always stored on word bound- aries, the data contained in the instruction is a word address. the word address is written to pc<20:1>, which accesses the desired byte address in program memory. instruction #2 in figure 5-4 shows how the instruction, goto 0006h , is encoded in the program memory. program branch instructions, which encode a relative address offset, operate in the same manner. the offset value stored in a branch instruction represents the number of single-word instructions that the pc will be offset by. section 24.0 ?instruction set summary? provides further details of the instruction set. 5.2.4 two-word instructions the standard pic18 instruction set has four two-word instructions: call , movff , goto and lsfr . in all cases, the second word of the instructions always has ? 1111 ? as its four most significant bits; the other 12 bits are literal data, usually a data memory address. the use of ? 1111 ? in the 4 msbs of an instruction specifies a special form of nop . if the instruction is executed in proper sequence ? immediately after the first word ? the data in the second word is accessed and used by the instruction sequence. if the first word is skipped for some reason and the second word is executed by itself, a nop is executed instead. this is necessary for cases when the two-word instruction is preceded by a conditional instruction that changes the pc. example 5-4 shows how this works. figure 5-4: instructions in program memory example 5-4: two-word instructions note: see section 5.5 ?program memory and the extended instruction set? for information on two-word instructions in the extended instruction set. case 1: object code source code 0110 0110 0000 0000 tstfsz reg1 ; is ram location 0? 1100 0001 0010 0011 movff reg1, reg2 ; no, skip this word 1111 0100 0101 0110 ; execute this word as a nop 0010 0100 0000 0000 addwf reg3 ; continue code case 2: object code source code 0110 0110 0000 0000 tstfsz reg1 ; is ram location 0? 1100 0001 0010 0011 movff reg1, reg2 ; yes, execute this word 1111 0100 0101 0110 ; 2nd word of instruction 0010 0100 0000 0000 addwf reg3 ; continue code word address lsb = 1 lsb = 0 program memory byte locations 000000h 000002h 000004h 000006h instruction 1: movlw 055h 0fh 55h 000008h instruction 2: goto 0006h efh 03h 00000ah f0h 00h 00000ch instruction 3: movff 123h, 456h c1h 23h 00000eh f4h 56h 000010h 000012h 000014h
? 2004 microchip technology inc. preliminary ds39629b-page 71 PIC18F6390/6490/8390/8490 5.3 data memory organization the data memory in pic18 devices is implemented as static ram. each register in the data memory has a 12-bit address, allowing up to 4096 bytes of data memory. the memory space is divided into as many as 16 banks that contain 256 bytes each; PIC18F6390/6490/8390/8490 devices implement only 4 banks. figure 5-5 shows the data memory organization for the PIC18F6390/6490/8390/8490 devices. the data memory contains special function registers (sfrs) and general purpose registers (gprs). the sfrs are used for control and status of the controller and peripheral functions, while gprs are used for data storage and scratchpad operations in the user?s application. any read of an unimplemented location will read as ? 0 ?s. the instruction set and architecture allow operations across all banks. the entire data memory may be accessed by direct, indirect or indexed addressing modes. addressing modes are discussed later in this section. to ensure that commonly used registers (sfrs and select gprs) can be accessed in a single cycle, pic18 devices implement an access bank. this is a 256-byte memory space that provides fast access to sfrs and the lower portion of gpr bank 0 without using the bsr. section 5.3.2 ?access bank? provides a detailed description of the access ram. 5.3.1 bank select register large areas of data memory require an efficient addressing scheme to make rapid access to any address possible. ideally, this means that an entire address does not need to be provided for each read or write operation. for pic18 devices, this is accom- plished with a ram banking scheme. this divides the memory space into 16 contiguous banks of 256 bytes. depending on the instruction, each location can be addressed directly by its full 12-bit address, or an 8-bit low-order address and a 4-bit bank pointer. most instructions in the pic18 instruction set make use of the bank pointer, known as the bank select register (bsr). this sfr holds the 4 most significant bits of a location?s address; the instruction itself includes the 8 least significant bits. only the four lower bits of the bsr are implemented (bsr3:bsr0). the upper four bits are unused; they will always read ? 0 ? and cannot be written to. the bsr can be loaded directly by using the movlb instruction. the value of the bsr indicates the bank in data memory; the 8 bits in the instruction show the location in the bank and can be thought of as an offset from the bank?s lower boundary. the relationship between the bsr?s value and the bank division in data memory is shown in figure 5-6. since up to 16 registers may share the same low-order address, the user must always be careful to ensure that the proper bank is selected before performing a data read or write. for example, writing what should be program data to an 8-bit address of f9h, while the bsr is 0fh will end up resetting the program counter. while any bank can be selected, only those banks that are actually implemented can be read or written to. writes to unimplemented banks are ignored, while reads from unimplemented banks will return ? 0 ?s. even so, the status register will still be affected as if the operation was successful. the data memory map in figure 5-5 indicates which banks are implemented. in the core pic18 instruction set, only the movff instruction fully specifies the 12-bit address of the source and target registers. this instruction ignores the bsr completely when it executes. all other instructions include only the low-order address as an operand and must use either the bsr or the access bank to locate their target registers. note: the operation of some aspects of data memory are changed when the pic18 extended instruction set is enabled. see section 5.6 ?data memory and the extended instruction set? for more information.
PIC18F6390/6490/8390/8490 ds39629b-page 72 preliminary ? 2004 microchip technology inc. figure 5-5: data memory map for PIC18F6390/6490/8390/8490 devices bank 0 bank 1 bank 14 bank 15 data memory map bsr<3:0> = 0000 = 0001 = 1111 060h 05fh f58h fffh 00h 5fh 60h ffh access bank when a = 0 : the bsr is ignored and the access bank is used. the first 128 bytes are general purpose ram (from bank 0). the second 128 bytes are special function registers (from bank 15). when a = 1 : the bsr specifies the bank used by the instruction. f00h effh 1ffh 100h 0ffh 000h access ram ffh 00h ffh 00h ffh 00h gpr gpr sfr gpr access ram high access ram low bank 2 = 0010 (sfrs) 2ffh 200h 300h bank 3 ffh 00h gpr = 0011 = 1110 f60h banked sfrs unused read as 00h to
? 2004 microchip technology inc. preliminary ds39629b-page 73 PIC18F6390/6490/8390/8490 figure 5-6: use of the bank select register (direct addressing) 5.3.2 access bank while the use of the bsr with an embedded 8-bit address allows users to address the entire range of data memory, it also means that the user must always ensure that the correct bank is selected. otherwise, data may be read from or written to the wrong location. this can be disastrous if a gpr is the intended target of an operation but an sfr is written to instead. verifying and/or changing the bsr for each read or write to data memory can become very inefficient. to streamline access for the most commonly used data memory locations, the data memory is configured with an access bank, which allows users to access a mapped block of memory without specifying a bsr. the access bank consists of the first 96 bytes of memory (00h-5fh) in bank 0 and the last 160 bytes of memory (60h-ffh) in block 15. the lower half is known as the ?access ram? and is composed of gprs. this upper half is where the device?s sfrs are mapped. these two areas are mapped contiguously in the access bank and can be addressed in a linear fashion by an 8-bit address (figure 5-5). the access bank is used by core pic18 instructions that include the access ram bit (the ?a? parameter in the instruction). when ?a? is equal to ? 1 ?, the instruction uses the bsr and the 8-bit address included in the opcode for the data memory address. when ?a? is ? 0 ?, however, the instruction is forced to use the access bank address map; the current value of the bsr is ignored entirely. using this ?forced? addressing allows the instruction to operate on a data address in a single cycle without updating the bsr first. for 8-bit addresses of 80h and above, this means that users can evaluate and operate on sfrs more efficiently. the access ram below 60h is a good place for data values that the user might need to access rapidly, such as immediate computational results or common program variables. access ram also allows for faster and more code efficient context saving and switching of variables. the mapping of the access bank is slightly different when the extended instruction set is enabled (xinst configuration bit = 1 ). this is discussed in more detail in section 5.6.3 ?mapping the access bank in indexed literal offset mode? . 5.3.3 general purpose register file pic18 devices may have banked memory in the gpr area. this is data ram, which is available for use by all instructions. gprs start at the bottom of bank 0 (address 000h) and grow upwards towards the bottom of the sfr area. gprs are not initialized by a power-on reset and are unchanged on all other resets. note 1: the access ram bit of the instruction can be used to force an override of the selected bank (bsr<3:0>) to the registers of the access bank. 2: the movff instruction embeds the entire 12-bit address in the instruction. data memory bank select (2) 7 0 from opcode (2) 0000 000h 100h 200h 300h f00h e00h fffh bank 0 bank 1 bank 2 bank 14 bank 15 00h ffh 00h ffh 00h ffh 00h ffh 00h ffh 00h ffh bank 3 through bank 13 0010 11111111 7 0 bsr (1) 11111111
PIC18F6390/6490/8390/8490 ds39629b-page 74 preliminary ? 2004 microchip technology inc. 5.3.4 special function registers the special function registers (sfrs) are registers used by the cpu and peripheral modules for controlling the desired operation of the device. these registers are implemented as static ram. sfrs start at the top of data memory (fffh) and extend downward to occupy three-quarters of bank 15 (from f40h to fffh). a list of these registers is given in table 5-1 and table 5-2. the sfrs can be classified into two sets: those associated with the ?core? device functionality (alu, resets and interrupts) and those related to the peripheral functions. the reset and interrupt registers are described in their respective chapters, while the alu?s status register is described later in this section. registers related to the operation of the peripheral features are described in the chapter for that peripheral. the sfrs are typically distributed among the peripherals whose functions they control. unused sfr locations are unimplemented and read as ? 0 ?s. table 5-1: special function register map for PIC18F6390/6490/8390/8490 devices address name address name address name address name fffh tosu fdfh indf2 (1) fbfh ccpr1h f9fh ipr1 ffeh tosh fdeh postinc2 (1) fbeh ccpr1l f9eh pir1 ffdh tosl fddh postdec2 (1) fbdh ccp1con f9dh pie1 ffch stkptr fdch preinc2 (1) fbch ccpr2h f9ch memcon (3) ffbh pclatu fdbh plusw2 (1) fbbh ccpr2l f9bh osctune ffah pclath fdah fsr2h fbah ccp2con f9ah trisj (3) ff9h pcl fd9h fsr2l fb9h ? (2) f99h trish (3) ff8h tblptru fd8h status fb8h ? (2) f98h trisg ff7h tblptrh fd7h tmr0h fb7h ? (2) f97h trisf ff6h tblptrl fd6h tmr0l fb6h ? (2) f96h trise ff5h tablat fd5h t0con fb5h cvrcon f95h trisd ff4h prodh fd4h ? (2) fb4h cmcon f94h trisc ff3h prodl fd3h osccon fb3h tmr3h f93h trisb ff2h intcon fd2h hlvdcon fb2h tmr3l f92h trisa ff1h intcon2 fd1h wdtcon fb1h t3con f91h latj (3) ff0h intcon3 fd0h rcon fb0h ? (2) f90h lath (3) fefh indf0 (1) fcfh tmr1h fafh spbrg1 f8fh latg feeh postinc0 (1) fceh tmr1l faeh rcreg1 f8eh latf fedh postdec0 (1) fcdh t1con fadh txreg1 f8dh late fech preinc0 (1) fcch tmr2 fach txsta1 f8ch latd febh plusw0 (1) fcbh pr2 fabh rcsta1 f8bh latc feah fsr0h fcah t2con faah ? (2) f8ah latb fe9h fsr0l fc9h sspbuf fa9h ? (2) f89h lata fe8h wreg fc8h sspadd fa8h ? (2) f88h portj (3) fe7h indf1 (1) fc7h sspstat fa7h ? (2) f87h porth (3) fe6h postinc1 (1) fc6h sspcon1 fa6h ? (2) f86h portg fe5h postdec1 (1) fc5h sspcon2 fa5h ipr3 f85h portf fe4h preinc1 (1) fc4h adresh fa4h pir3 f84h porte fe3h plusw1 (1) fc3h adresl fa3h pie3 f83h portd fe2h fsr1h fc2h adcon0 fa2h ipr2 f82h portc fe1h fsr1l fc1h adcon1 fa1h pir2 f81h portb fe0h bsr fc0h adcon2 fa0h pie2 f80h porta note 1: this is not a physical register. 2: unimplemented registers are read as ? 0 ?. 3: this register is not available on 64-pin devices. 4: this register is implement ed but unused on 64-pin devices.
? 2004 microchip technology inc. preliminary ds39629b-page 75 PIC18F6390/6490/8390/8490 table 5-1: special function register map for PIC18F6390/6490/8390/8490 devices (continued) address name address name address name address name f7fh spbrgh1 f6fh spbrg2 f5fh lcdse5 (3) f4fh ? (2) f7eh baudcon1 f6eh rcreg2 f5eh lcdse4 (3) f4eh ? (2) f7dh ? (2) f6dh txreg2 f5dh lcdse3 f4dh ? (2) f7ch lcddata23 (4) f6ch txsta2 f5ch lcdse2 f4ch ? (2) f7bh lcddata22 (4) f6bh rcsta2 f5bh lcdse1 f4bh ? (2) f7ah lcddata21 f6ah lcddata10 (4) f5ah lcdse0 f4ah ? (2) f79h lcddata20 f69h lcddata9 f59h lcdcon f49h ? (2) f78h lcddata19 f68h lcddata8 f58h lcdps f48h ? (2) f77h lcddata18 f67h lcddata7 f57h ? (2) f47h ? (2) f76h lcddata17 (4) f66h lcddata6 f56h ? (2) f46h ? (2) f75h lcddata16 (4) f65h lcddata5 (4) f55h ? (2) f45h ? (2) f74h lcddata15 f64h lcddata4 (4) f54h ? (2) f44h ? (2) f73h lcddata14 f63h lcddata3 f53h ? (2) f43h ? (2) f72h lcddata13 f62h lcddata2 f52h ? (2) f42h ? (2) f71h lcddata12 f61h lcddata1 f51h ? (2) f41h ? (2) f70h lcddata11 (4) f60h lcddata0 f50h ? (2) f40h ? (2) note 1: this is not a physical register. 2: unimplemented registers are read as ? 0 ?. 3: this register is not available on 64-pin devices. 4: this register is implement ed but unused on 64-pin devices.
PIC18F6390/6490/8390/8490 ds39629b-page 76 preliminary ? 2004 microchip technology inc. table 5-2: PIC18F6390/6490/8390/8490 register file summary file name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 value on por, bor details on page: tosu ? ? ? top-of-stack upper byte (tos<20:16>) ---0 0000 59, 66 tosh top-of-stack high byte (tos<15:8>) 0000 0000 59, 66 tosl top-of-stack low byte (tos<7:0>) 0000 0000 59, 66 stkptr stkful stkunf ? return stack pointer 00-0 0000 59, 67 pclatu ? ? ? holding register for pc<20:16> ---0 0000 59, 66 pclath holding register for pc<15:8> 0000 0000 59, 66 pcl pc low byte (pc<7:0>) 0000 0000 59, 66 tblptru ? ? bit 21 program memory table pointer upper byte (tblptr<20:16>) --00 0000 59, 88 tblptrh program memory table pointer high byte (tblptr<15:8>) 0000 0000 59, 88 tblptrl program memory table pointer low byte (tblptr<7:0>) 0000 0000 59, 88 tablat program memory table latch 0000 0000 59, 88 prodh product register high byte xxxx xxxx 59, 91 prodl product register low byte xxxx xxxx 59, 91 intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 0000 000x 59, 95 intcon2 rbpu intedg0 intedg1 intedg2 intedg3 tmr0ip int3ip rbip 1111 1111 59, 96 intcon3 int2ip int1ip int3ie int2ie int1ie int3if int2if int1if 1100 0000 59, 97 indf0 uses contents of fsr0 to address data memory ? value of fsr0 not changed (not a physical register) n/a 59, 82 postinc0 uses contents of fsr0 to address data memory ? value of fsr0 post-incremented (not a physical register) n/a 59, 83 postdec0 uses contents of fsr0 to address data memory ? value of fsr0 post-decremented (not a physical register) n/a 59, 83 preinc0 uses contents of fsr0 to address data memory ? value of fsr0 pre-incremented (not a physical register) n/a 59, 83 plusw0 uses contents of fsr0 to address data memory ? value of fsr0 pre-incremented (not a physical register), value of fsr0 offset by w n/a 59, 83 fsr0h ? ? ? ? indirect data memory address pointer 0 high ---- xxxx 59, 82 fsr0l indirect data memory address pointer 0 low byte xxxx xxxx 59, 82 wreg working register xxxx xxxx 59 indf1 uses contents of fsr1 to address data memory ? value of fsr1 not changed (not a physical register) n/a 59, 82 postinc1 uses contents of fsr1 to address data memory ? value of fsr1 post-incremented (not a physical register) n/a 59, 83 postdec1 uses contents of fsr1 to address data memory ? value of fsr1 post-decremented (not a physical register) n/a 59, 83 preinc1 uses contents of fsr1 to address data memory ? value of fsr1 pre-incremented (not a physical register) n/a 59, 83 plusw1 uses contents of fsr1 to address data memory ? value of fsr1 pre-incremented (not a physical register), value of fsr1 offset by w n/a 59, 83 fsr1h ? ? ? ? indirect data memory address pointer 1 high ---- xxxx 60, 82 fsr1l indirect data memory address pointer 1 low byte xxxx xxxx 60, 82 bsr ? ? ? ? bank select register ---- 0000 60, 71 indf2 uses contents of fsr2 to address data memory ? value of fsr2 not changed (not a physical register) n/a 60, 82 postinc2 uses contents of fsr2 to address data memory ? value of fsr2 post-incremented (not a physical register) n/a 60, 83 postdec2 uses contents of fsr2 to address data memory ? value of fsr2 post-decremented (not a physical register) n/a 60, 83 preinc2 uses contents of fsr2 to address data memory ? value of fsr2 pre-incremented (not a physical register) n/a 60, 83 plusw2 uses contents of fsr2 to address data memory ? value of fsr2 pre-incremented (not a physical register), value of fsr2 offset by w n/a 60, 83 fsr2h ? ? ? ? indirect data memory address pointer 2 high ---- xxxx 60, 82 fsr2l indirect data memory address pointer 2 low byte xxxx xxxx 60, 82 status ? ? ?novzdcc ---x xxxx 60, 80 legend: x = unknown, u = unchanged, ? = unimplemented, q = value depends on condition note 1: the sboren bit is only available when the boren1:boren0 configuration bits = 01 ; otherwise it is disabled and reads as ? 0 ?. see section 4.4 ?brown-out reset (bor)? . 2: these registers and/or bits are not implemented on 64-pin devices; read as ? 0 ?. 3: the pllen bit is only available in specific oscillator configuration; otherwise, it is disabled and reads as ? 0 ?. see section 2.6.4 ?pll in intosc modes? . 4: the rg5 bit is only available when master clear is disabled (mclre configuration bit = 0 ); otherwise, rg5 reads as ? 0 ?. this bit is read-only. 5: ra6/ra7 and their associated latch and direction bits are individually configured as port pins based on various primary oscilla tor modes. when disabled, these bits read as ? 0 ?. 6: these registers are implemented but unused in 64-pin devices and may be used as general-purpose data ram if required.
? 2004 microchip technology inc. preliminary ds39629b-page 77 PIC18F6390/6490/8390/8490 tmr0h timer0 register high byte 0000 0000 60, 132 tmr0l timer0 register low byte xxxx xxxx 60, 132 t0con tmr0on t08bit t0cs t0se psa t0ps2 t0ps1 t0ps0 1111 1111 60, 131 osccon idlen ircf2 ircf1 ircf0 osts iofs scs1 scs0 0100 q000 38, 60 hlvdcon vdirmag ? irvst hlvden hlvdl3 hlvdl2 hlvdl1 hlvdl0 0-00 0101 60, 251 wdtcon ? ? ? ? ? ? ?swdten --- ---0 60, 288 rcon ipen sboren (1) ?ri to pd por bor 0q-1 11q0 52, 60, 107 tmr1h timer1 register high byte xxxx xxxx 60, 137 tmr1l timer1 register low byte xxxx xxxx 60, 137 t1con rd16 t1run t1ckps1 t1ckps0 t1oscen t1sync tmr1cs tmr1on 0000 0000 60, 135 tmr2 timer2 register 0000 0000 60, 141 pr2 timer2 period register 1111 1111 60, 141 t2con ? t2outps3 t2outps2 t2outps1 t2outps0 tmr2on t2ckps1 t2ckps0 -000 0000 60, 141 sspbuf ssp receive buffer/transmit register xxxx xxxx 60, 158, 166 sspadd ssp address register in i 2 c? slave mode. ssp baud rate reload register in i 2 c master mode. 0000 0000 60, 166 sspstat smp cke d/a psr/w ua bf 0000 0000 60, 158, 167 sspcon1 wcol sspov sspen ckp sspm3 sspm2 sspm1 sspm0 0000 0000 60, 159, 168 sspcon2 gcen ackstat ackdt acken rcen pen rsen sen 0000 0000 60, 169 adresh a/d result register high byte xxxx xxxx 61, 240 adresl a/d result register low byte xxxx xxxx 61, 240 adcon0 ? ? chs3 chs2 chs1 chs0 go/done adon --00 0000 61, 231 adcon1 ? ? vcfg1 vcfg0 pcfg3 pcfg2 pcfg1 pcfg0 --00 0000 61, 232 adcon2 adfm ? acqt2 acqt1 acqt0 adcs2 adcs1 adcs0 0-00 0000 61, 233 ccpr1h capture/compare/pwm register 1 high byte xxxx xxxx 61, 152, 155 ccpr1l capture/compare/pwm register 1 low byte xxxx xxxx 61, 152, 155 ccp1con ? ? dc1b1 dc1b0 ccp1m3 ccp1m2 ccp1m1 ccp1m0 --00 0000 61, 147 ccpr2h capture/compare/pwm register 2 high byte xxxx xxxx 61, 152, 155 ccpr2l capture/compare/pwm register 2 low byte xxxx xxxx 61, 152, 155 ccp2con ? ? dc2b1 dc2b0 ccp2m3 ccp2m2 ccp2m1 ccp2m0 --00 0000 61, 147 cvrcon cvren cvroe cvrr cvrss cvr3 cvr2 cvr1 cvr0 000- 0000 61, 247 cmcon c2out c1out c2inv c1inv cis cm2 cm1 cm0 0000 0111 61, 241 tmr3h timer3 register high byte xxxx xxxx 61, 145 tmr3l timer3 register low byte xxxx xxxx 61, 145 t3con rd16 t3ccp2 t3ckps1 t3ckps0 t3ccp1 t3sync tmr3cs tmr3on 0000 0000 61, 143 table 5-2: PIC18F6390/6490/8390/8490 register file summary (continued) file name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 value on por, bor details on page: legend: x = unknown, u = unchanged, ? = unimplemented, q = value depends on condition note 1: the sboren bit is only available when the boren1:boren0 configuration bits = 01 ; otherwise it is disabled and reads as ? 0 ?. see section 4.4 ?brown-out reset (bor)? . 2: these registers and/or bits are not implemented on 64-pin devices; read as ? 0 ?. 3: the pllen bit is only available in specific oscillator configuration; otherwise, it is disabled and reads as ? 0 ?. see section 2.6.4 ?pll in intosc modes? . 4: the rg5 bit is only available when master clear is disabled (mclre configuration bit = 0 ); otherwise, rg5 reads as ? 0 ?. this bit is read-only. 5: ra6/ra7 and their associated latch and direction bits are individually configured as port pins based on various primary oscilla tor modes. when disabled, these bits read as ? 0 ?. 6: these registers are implemented but unused in 64-pin devices and may be used as general-purpose data ram if required.
PIC18F6390/6490/8390/8490 ds39629b-page 78 preliminary ? 2004 microchip technology inc. spbrg1 eusart1 baud rate generator 0000 0000 61, 201 rcreg1 eusart1 receive register 0000 0000 61, 208 txreg1 eusart1 transmit register 0000 0000 61, 206 txsta1 csrc tx9 txen sync sendb brgh trmt tx9d 0000 0000 61, 198 rcsta1 spen rx9 sren cren adden ferr oerr rx9d 0000 000x 61, 199 ipr3 ? lcdip rc2ip tx2ip ? ? ? ? -111 ---- 61, 106 pir3 ? lcdif rc2if tx2if ? ? ? ? -000 ---- 61, 100 pie3 ? lcdie rc2ie tx2ie ? ? ? ? -000 ---- 61, 103 ipr2 oscfip cmip ? ? bclip hlvdip tmr3ip ccp2ip 11-- 1111 61, 105 pir2 oscfif cmif ? ? bclif hlvdif tmr3if ccp2if 00-- 0000 61, 99 pie2 oscfie cmie ? ? bclie hlvdie tmr3ie ccp2ie 00-- 0000 61, 102 ipr1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip -111 1111 61, 104 pir1 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if -000 0000 61, 98 pie1 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie -000 0000 61, 101 osctune intsrc pllen (3) ? tun4 tun3 tun2 tun1 tun0 00-0 0000 35, 61 trisj (2) data direction control register for portj 1111 1111 62, 130 trish (2) data direction control register for porth 1111 1111 62, 128 trisg ? ? ? data direction control register for portg ---1 1111 62, 126 trisf data direction control register for portf 1111 1111 62, 124 trise data direction control register for porte ? ? ? ? 1111 ---- 62, 121 trisd data direction control register for portd 1111 1111 62, 119 trisc data direction control register for portc 1111 1111 62, 117 trisb data direction control register for portb 1111 1111 62, 114 trisa trisa7 (5) trisa6 (5) data direction control register for porta 1111 1111 62, 111 latj (2) read portj data latch, write portj data latch xxxx xxxx 62, 130 lath (2) read porth data latch, write porth data latch xxxx xxxx 62, 128 latg ? ? ? read portg data latch, write portg data latch ---x xxxx 62, 126 latf read portf data latch, write portf data latch xxxx xxxx 62, 124 late read porte data latch, write porte data latch ? ? ? ? xxxx xxxx 62, 121 latd read portd data latch, write portd data latch xxxx xxxx 62, 119 latc read portc data latch, write portc data latch xxxx xxxx 62, 117 latb read portb data latch, write portb data latch xxxx xxxx 62, 114 lata lata7 (5) lata6 (5) read porta data latch, write porta data latch xxxx xxxx 62, 111 portj (2) read portj pins, write portj data latch xxxx xxxx 62, 130 porth (2) read porth pins, write porth data latch xxxx xxxx 62, 128 portg ? ?rg5 (4) read portg pins <4:0>, write portg data latch <4:0> --xx xxxx 62, 126 portf read portf pins, write portf data latch xxxx xxxx 62, 124 porte read porte pins, write porte data latch ? ? ? ? xxxx xxxx 62, 121 portd read portd pins, write portd data latch xxxx xxxx 62, 119 portc read portc pins, write portc data latch xxxx xxxx 62, 117 portb read portb pins, write portb data latch xxxx xxxx 62, 114 porta ra7 (5) ra6 (5) read porta pins, write porta data latch xx0x 0000 62, 111 table 5-2: PIC18F6390/6490/8390/8490 register file summary (continued) file name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 value on por, bor details on page: legend: x = unknown, u = unchanged, ? = unimplemented, q = value depends on condition note 1: the sboren bit is only available when the boren1:boren0 configuration bits = 01 ; otherwise it is disabled and reads as ? 0 ?. see section 4.4 ?brown-out reset (bor)? . 2: these registers and/or bits are not implemented on 64-pin devices; read as ? 0 ?. 3: the pllen bit is only available in specific oscillator configuration; otherwise, it is disabled and reads as ? 0 ?. see section 2.6.4 ?pll in intosc modes? . 4: the rg5 bit is only available when master clear is disabled (mclre configuration bit = 0 ); otherwise, rg5 reads as ? 0 ?. this bit is read-only. 5: ra6/ra7 and their associated latch and direction bits are individually configured as port pins based on various primary oscilla tor modes. when disabled, these bits read as ? 0 ?. 6: these registers are implemented but unused in 64-pin devices and may be used as general-purpose data ram if required.
? 2004 microchip technology inc. preliminary ds39629b-page 79 PIC18F6390/6490/8390/8490 spbrgh1 eusart1 baud rate generator high byte 0000 0000 62, 201 baudcon1 abdovf rcidl ? sckp brg16 ? wue abden 01-0 0-00 62, 200 lcddata23 (6) s47c3 s46c3 s45c3 s44c3 s43c3 s42c3 s41c3 s40c3 xxxx xxxx 63, 261 lcddata22 (6) s39c3 s38c3 s37c3 s36c3 s35c3 s34c3 s33c3 s32c3 xxxx xxxx 63, 261 lcddata21 s31c3 s30c3 s29c3 s28c3 s27c3 s26c3 s25c3 s24c3 xxxx xxxx 63, 261 lcddata20 s23c3 s22c3 s21c3 s20c3 s19c3 s18c3 s17c3 s16c3 xxxx xxxx 63, 261 lcddata19 s15c3 s14c3 s13c3 s12c3 s11c3 s10c3 s09c3 s08c3 xxxx xxxx 63, 261 lcddata18 s07c3 s06c3 s05c3 s04c3 s03c3 s02c3 s01c3 s00c3 xxxx xxxx 63, 261 lcddata17 (6) s47c2 s46c2 s45c2 s44c2 s43c2 s42c2 s41c2 s40c2 xxxx xxxx 63, 261 lcddata16 (6) s39c2 s38c2 s37c2 s36c2 s35c2 s34c2 s33c2 s32c2 xxxx xxxx 63, 261 lcddata15 s31c2 s30c2 s29c2 s28c2 s27c2 s26c2 s25c2 s24c2 xxxx xxxx 63, 261 lcddata14 s23c2 s22c2 s21c2 s20c2 s19c2 s18c2 s17c2 s16c2 xxxx xxxx 63, 261 lcddata13 s15c2 s14c2 s13c2 s12c2 s11c2 s10c2 s09c2 s08c2 xxxx xxxx 63, 261 lcddata12 s07c2 s06c2 s05c2 s04c2 s03c2 s02c2 s01c2 s00c2 xxxx xxxx 63, 261 lcddata11 (6) s47c1 s46c1 s45c1 s44c1 s43c1 s42c1 s41c1 s40c1 xxxx xxxx 63, 261 spbrg2 ausart2 baud rate generator 0000 0000 63, 220 rcreg2 ausart2 receive register 0000 0000 63, 224 txreg2 ausart2 transmit register 0000 0000 63, 222 txsta2 csrc tx9 txen sync ? brgh trmt tx9d 0000 0010 63, 218 rcsta2 spen rx9 sren cren adden ferr oerr rx9d 0000 000x 63, 219 lcddata10 (6) s39c1 s38c1 s37c1 s36c1 s35c1 s34c1 s33c1 s32c1 xxxx xxxx 63, 261 lcddata9 s31c1 s30c1 s29c1 s28c1 s27c1 s26c1 s25c1 s24c1 xxxx xxxx 63, 261 lcddata8 s23c1 s22c1 s21c1 s20c1 s19c1 s18c1 s17c1 s16c1 xxxx xxxx 63, 261 lcddata7 s15c1 s14c1 s13c1 s12c1 s11c1 s10c1 s09c1 s08c1 xxxx xxxx 63, 261 lcddata6 s07c1 s06c1 s05c1 s04c1 s03c1 s02c1 s01c1 s00c1 xxxx xxxx 63, 261 lcddata5 (6) s47c0 s46c0 s45c0 s44c0 s43c0 s42c0 s41c0 s40c0 xxxx xxxx 63, 261 lcddata4 (6) s39c0 s38c0 s37c0 s36c0 s35c0 s34c0 s33c0 s32c0 xxxx xxxx 63, 261 lcddata3 s31c0 s30c0 s29c0 s28c0 s27c0 s26c0 s25c0 s24c0 xxxx xxxx 63, 261 lcddata2 s23c0 s22c0 s21c0 s20c0 s19c0 s18c0 s17c0 s16c0 xxxx xxxx 63, 261 lcddata1 s15c0 s14c0 s13c0 s12c0 s11c0 s10c0 s09c0 s08c0 xxxx xxxx 63, 261 lcddata0 s07c0 s06c0 s05c0 s04c0 s03c0 s02c0 s01c0 s00c0 xxxx xxxx 63, 261 lcdse5 (2) se47 se46 se45 se44 se43 se42 se41 se40 0000 0000 64, 261 lcdse4 (2) se39 se38 se37 se36 se35 se34 se33 se32 0000 0000 64, 260 lcdse3 se31 se30 se29 se28 se27 se26 se25 se24 0000 0000 64, 261 lcdse2 se23 se22 se21 se20 se19 se18 se17 se16 0000 0000 64, 261 lcdse1 se15 se14 se13 se12 se11 se10 se9 se8 0000 0000 64, 261 lcdse0 se7 se6 se5 se4 se3 se2 se1 se0 0000 0000 64, 261 lcdcon lcden slpen werr ? cs1 cs0 lmux1 lmux0 000- 0000 64, 258 lcdps wft biasmd lcda wa lp3 lp2 lp1 lp0 0000 0000 64, 259 table 5-2: PIC18F6390/6490/8390/8490 register file summary (continued) file name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 value on por, bor details on page: legend: x = unknown, u = unchanged, ? = unimplemented, q = value depends on condition note 1: the sboren bit is only available when the boren1:boren0 configuration bits = 01 ; otherwise it is disabled and reads as ? 0 ?. see section 4.4 ?brown-out reset (bor)? . 2: these registers and/or bits are not implemented on 64-pin devices; read as ? 0 ?. 3: the pllen bit is only available in specific oscillator configuration; otherwise, it is disabled and reads as ? 0 ?. see section 2.6.4 ?pll in intosc modes? . 4: the rg5 bit is only available when master clear is disabled (mclre configuration bit = 0 ); otherwise, rg5 reads as ? 0 ?. this bit is read-only. 5: ra6/ra7 and their associated latch and direction bits are individually configured as port pins based on various primary oscilla tor modes. when disabled, these bits read as ? 0 ?. 6: these registers are implemented but unused in 64-pin devices and may be used as general-purpose data ram if required.
PIC18F6390/6490/8390/8490 ds39629b-page 80 preliminary ? 2004 microchip technology inc. 5.3.5 status register the status register, shown in register 5-2, contains the arithmetic status of the alu. as with any other sfr, it can be the operand for any instruction. if the status register is the destination for an instruction that affects the z, dc, c, ov or n bits, the results of the instruction are not written; instead, the status is updated according to the instruction performed. there- fore, the result of an instruction with the status register as its destination may be different than intended. as an example, clrf status will set the z bit and leave the remaining status bits unchanged (? 000u u1uu ?). it is recommended that only bcf , bsf , swapf , movff and movwf instructions are used to alter the status register, because these instructions do not affect the z, c, dc, ov or n bits in the status register. for other instructions that do not affect status bits, see the instruction set summaries in table 24-2 and table 24-3. register 5-2: status register note: the c and dc bits operate as a borrow and digit borrow bit respectively, in subtraction. u-0 u-0 u-0 r/w-x r/w-x r/w-x r/w-x r/w-x ? ? ?novzdcc bit 7 bit 0 bit 7-5 unimplemented: read as ? 0 ? bit 4 n: negative bit this bit is used for signed arithmetic (2?s complement). it indicates whether the result was negative (alu msb = 1 ). 1 = result was negative 0 = result was positive bit 3 ov: overflow bit this bit is used for signed arithmetic (2?s complement). it indicates an overflow of the 7-bit magnitude, which causes the sign bit (bit7) to change state. 1 = overflow occurred for signed arithmetic (in this arithmetic operation) 0 = no overflow occurred bit 2 z: zero bit 1 = the result of an arithmetic or logic operation is zero 0 = the result of an arithmetic or logic operation is not zero bit 1 dc: digit carry/borrow bit for addwf, addlw, sublw and subwf instructions: 1 = a carry-out from the 4th low-order bit of the result occurred 0 = no carry-out from the 4th low-order bit of the result note: for borrow, the polarity is reversed. a subtraction is executed by adding the 2?s complement of the second operand. for rotate ( rrf , rlf ) instructions, this bit is loaded with either bit 4 or bit 3 of the source register. bit 0 c: carry/borrow bit for addwf, addlw, sublw and subwf instructions: 1 = a carry-out from the most significant bit of the result occurred 0 = no carry-out from the most significant bit of the result occurred note: for borrow, the polarity is reversed. a subtraction is executed by adding the 2?s complement of the second operand. for rotate ( rrf , rlf ) instructions, this bit is loaded with either the high or low-order bit of the source register. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
? 2004 microchip technology inc. preliminary ds39629b-page 81 PIC18F6390/6490/8390/8490 5.4 data addressing modes while the program memory can be addressed in only one way ? through the program counter ? information in the data memory space can be addressed in several ways. for most instructions, the addressing mode is fixed. other instructions may use up to three modes, depending on which operands are used and whether or not the extended instruction set is enabled. the addressing modes are: inherent literal direct indirect an additional addressing mode, indexed literal offset, is available when the extended instruction set is enabled (xinst configuration bit = 1 ). its operation is discussed in greater detail in section 5.6.1 ?indexed addressing with literal offset? . 5.4.1 inherent and literal addressing many pic18 control instructions do not need any argument at all; they either perform an operation that globally affects the device, or they operate implicitly on one register. this addressing mode is known as inherent addressing. examples include sleep , reset and daw . other instructions work in a similar way but require an additional explicit argument in the opcode. this is known as literal addressing mode, because they require some literal value as an argument. examples include addlw and movlw , which respectively add or move a literal value to the w register. other examples include call and goto , which include a 20-bit program memory address. 5.4.2 direct addressing direct addressing specifies all or part of the source and/or destination address of the operation within the opcode itself. the options are specified by the arguments accompanying the instruction. in the core pic18 instruction set, bit-oriented and byte-oriented instructions use some version of direct addressing by default. all of these instructions include some 8-bit literal address as their least significant byte. this address specifies either a register address in one of the banks of data ram ( section 5.3.3 ?general purpose register file? ), or a location in the access bank ( section 5.3.2 ?access bank? ) as the data source for the instruction. the access ram bit ?a? determines how the address is interpreted. when ?a? is ? 1 ?, the contents of the bsr ( section 5.3.1 ?bank select register? ) are used with the address to determine the complete 12-bit address of the register. when ?a? is ? 0 ?, the address is interpreted as being a register in the access bank. addressing that uses the access ram is sometimes also known as direct forced addressing mode. a few instructions, such as movff , include the entire 12-bit address (either source or destination) in their op codes. in those cases, the bsr is ignored entirely. the destination of the operation?s results is determined by the destination bit ?d?. when ?d? is ? 1 ?, the results are stored back in the source register, overwriting its origi- nal contents. when ?d? is ? 0 ?, the results are stored in the w register. instructions without the ?d? argument have a destination that is implicit in the instruction; their destination is either the target register being operated on, or the w register. 5.4.3 indirect addressing indirect addressing allows the user to access a location in data memory without giving a fixed address in the instruction. this is done by using file select registers (fsrs) as pointers to the locations to be read or written to. since the fsrs are themselves located in ram as special file registers, they can also be directly manip- ulated under program control. this makes fsrs very useful in implementing data structures, such as tables and arrays in data memory. the registers for indirect addressing are also implemented with indirect file operands (indfs) that permit automatic manipulation of the pointer value with auto-incrementing, auto-decrementing or offsetting with another value. this allows for efficient code using loops, such as the example of clearing an entire ram bank in example 5-5. it also enables users to perform indexed addressing and other stack pointer operations for program memory in data memory. example 5-5: how to clear ram (bank 1) using indirect addressing note: the execution of some instructions in the core pic18 instruction set are changed when the pic18 extended instruction set is enabled. see section 5.6 ?data memory and the extended instruction set? for more information. lfsr fsr0, 100h ; next clrf postinc0 ; clear indf ; register then ; inc pointer btfss fsr0h, 1 ; all done with ; bank1? bra next ; no, clear next continue ; yes, continue
PIC18F6390/6490/8390/8490 ds39629b-page 82 preliminary ? 2004 microchip technology inc. 5.4.3.1 fsr registers and the indf operand at the core of indirect addressing are three sets of registers: fsr0, fsr1 and fsr2. each represents a pair of 8-bit registers, fsrnh and fsrnl. the four upper bits of the fsrnh register are not used, so each fsr pair holds a 12-bit value. this represents a value that can address the entire range of the data memory in a linear fashion. the fsr register pairs, then, serve as pointers to data memory locations. indirect addressing is accomplished with a set of indirect file operands, indf0 through indf2. these can be thought of as ?virtual? registers: they are mapped in the sfr space but are not physically implemented. reading or writing to a particular indf register actually accesses its corresponding fsr register pair. a read from indf1, for example, reads the data at the address indicated by fsr1h:fsr1l. instructions that use the indf registers as operands actually use the contents of their corresponding fsr as a pointer to the instruction?s target. the indf operand is just a convenient way of using the pointer. because indirect addressing uses a full 12-bit address, data ram banking is not necessary. thus, the current contents of the bsr and the access ram bit have no effect on determining the target address. figure 5-7: indirect addressing fsr1h:fsr1l 0 7 data memory 000h 100h 200h 300h f00h e00h fffh bank 0 bank 1 bank 2 bank 14 bank 15 bank 3 through bank 13 addwf, indf1, 1 0 7 using an instruction with one of the indirect addressing registers as the operand.... ...uses the 12-bit address stored in the fsr pair associated with that register.... ...to determine the data memory location to be used in that operation. in this case, the fsr1 pair contains fcch. this means the contents of location fcch will be added to that of the w register and stored back in fcch. xxxx 1111 11001100
? 2004 microchip technology inc. preliminary ds39629b-page 83 PIC18F6390/6490/8390/8490 5.4.3.2 fsr registers and postinc, postdec, preinc and plusw in addition to the indf operand, each fsr register pair also has four additional indirect operands. like indf, these are ?virtual? registers that cannot be indirectly read or written to. accessing these registers actually accesses the associated fsr register pair, but also performs a specific action on its stored value. they are: postdec: accesses the fsr value, then automatically decrements it by ? 1 ? afterwards postinc: accesses the fsr value, then automatically increments it by ? 1 ? afterwards preinc: increments the fsr value by ? 1 ?, then uses it in the operation plusw: adds the signed value of the w register (range of -127 to 128) to that of the fsr and uses the new value in the operation. in this context, accessing an indf register uses the value in the fsr registers without changing them. similarly, accessing a plusw register gives the fsr value offset by the value in the w register; neither value is actually changed in the operation. accessing the other virtual registers changes the value of the fsr registers. operations on the fsrs with postdec, postinc and preinc affect the entire register pair; that is, roll- overs of the fsrnl register from ffh to 00h carry over to the fsrnh register. on the other hand, results of these operations do not change the value of any flags in the status register (e.g., z, n, ov, etc.). the plusw register can be used to implement a form of indexed addressing in the data memory space. by manipulating the value in the w register, users can reach addresses that are fixed offsets from pointer addresses. in some applications, this can be used to implement some powerful program control structure, such as software stacks, inside of data memory. 5.4.3.3 operations by fsrs on fsrs indirect addressing operations that target other fsrs or virtual registers represent special cases. for exam- ple, using an fsr to point to one of the virtual registers will not result in successful operations. as a specific case, assume that fsr0h:fsr0l contains fe7h, the address of indf1. attempts to read the value of the indf1, using indf0 as an operand, will return 00h. attempts to write to indf1, using indf0 as the operand, will result in a nop . on the other hand, using the virtual registers to write to an fsr pair may not occur as planned. in these cases, the value will be written to the fsr pair, but without any incrementing or decrementing. thus, writing to indf2 or postdec2 will write the same value to the fsr2h:fsr2l. since the fsrs are physical registers mapped in the sfr space, they can be manipulated through all direct operations. users should proceed cautiously when working on these registers, particularly if their code uses indirect addressing. similarly, operations by indirect addressing are gener- ally permitted on all other sfrs. users should exercise the appropriate caution that they do not inadvertently change settings that might affect the operation of the device.
PIC18F6390/6490/8390/8490 ds39629b-page 84 preliminary ? 2004 microchip technology inc. 5.5 program memory and the extended instruction set the operation of program memory is unaffected by the use of the extended instruction set. enabling the extended instruction set adds five addi- tional two-word commands to the existing pic18 instruction set: addfsr , callw , movsf , movss and subfsr . these instructions are executed as described in section 5.2.4 ?two-word instructions? . 5.6 data memory and the extended instruction set enabling the pic18 extended instruction set (xinst configuration bit = 1 ) significantly changes certain aspects of data memory and its addressing. specifically, the use of the access bank for many of the core pic18 instructions is different; this is due to the introduction of a new addressing mode for the data memory space. this mode also alters the behavior of indirect addressing using fsr2 and its associated operands. what does not change is just as important. the size of the data memory space is unchanged, as well as its linear addressing. the sfr map remains the same. core pic18 instructions can still operate in both direct and indirect addressing mode; inherent and literal instructions do not change at all. indirect addressing with fsr0 and fsr1 also remains unchanged. 5.6.1 indexed addressing with literal offset enabling the pic18 extended instruction set changes the behavior of indirect addressing using the fsr2 register pair and its associated file operands. under the proper conditions, instructions that use the access bank ? that is, most bit-oriented and byte-oriented instructions ? can invoke a form of indexed addressing using an offset specified in the instruction. this special addressing mode is known as indexed addressing with literal offset, or indexed literal offset mode. when using the extended instruction set, this addressing mode requires the following: the use of the access bank is forced (?a? = 0 ); and the file address argument is less than or equal to 5fh. under these conditions, the file address of the instruction is not interpreted as the lower byte of an address (used with the bsr in direct addressing), or as an 8-bit address in the access bank. instead, the value is interpreted as an offset value to an address pointer specified by fsr2. the offset and the contents of fsr2 are added to obtain the target address of the operation. 5.6.2 instructions affected by indexed literal offset mode any of the core pic18 instructions that can use direct addressing are potentially affected by the indexed literal offset addressing mode. this includes all byte-oriented and bit-oriented instructions, or almost one-half of the standard pic18 instruction set. instruc- tions that only use inherent or literal addressing modes are unaffected. additionally, byte-oriented and bit-oriented instructions are not affected if they use the access bank (access ram bit is ? 1 ?), or include a file address of 60h or above. instructions meeting these criteria will continue to execute as before. a comparison of the different possi- ble addressing modes when the extended instruction set is enabled is shown in figure 5-8. those who desire to use byte-oriented or bit-oriented instructions in the indexed literal offset mode should note the changes to assembler syntax for this mode. this is described in more detail in section 24.2.1 ?extended instruction syntax? .
? 2004 microchip technology inc. preliminary ds39629b-page 85 PIC18F6390/6490/8390/8490 figure 5-8: comparing addressing options for bit-oriented and byte-oriented instructions (extended instruction set enabled) example instruction: addwf, f, d, a (opcode: 0010 01da ffff ffff ) when a = 0 and f 60h: the instruction executes in direct forced mode. ?f? is interpreted as a location in the access ram between 060h and fffh. this is the same as locations f60h to fffh (bank 15) of data memory. locations below 060h are not available in this addressing mode. when a = 0 and f 5fh: the instruction executes in indexed literal offset mode. ?f? is interpreted as an offset to the address value in fsr2. the two are added together to obtain the address of the target register for the instruction. the address can be anywhere in the data memory space. note that in this mode, the correct syntax is now: addwf [k], d where ?k? is the same as ?f?. when a = 1 (all values of f): the instruction executes in direct mode (also known as direct long mode). ?f? is interpreted as a location in one of the 16 banks of the data memory space. the bank is designated by the bank select register (bsr). the address can be in any implemented bank in the data memory space. 000h 060h 100h f00h f40h fffh valid range 00h 60h ffh data memory access ram bank 0 bank 1 through bank 14 bank 15 sfrs 000h 060h 100h f00h f40h fffh data memory bank 0 bank 1 through bank 14 bank 15 sfrs fsr2h fsr2l ffffffff 001001da ffffffff 001001da 000h 060h 100h f00h f40h fffh data memory bank 0 bank 1 through bank 14 bank 15 sfrs for ?f? bsr 00000000
PIC18F6390/6490/8390/8490 ds39629b-page 86 preliminary ? 2004 microchip technology inc. 5.6.3 mapping the access bank in indexed literal offset mode the use of indexed literal offset addressing mode effectively changes how the lower part of access ram (00h to 5fh) is mapped. rather than containing just the contents of the bottom part of bank 0, this mode maps the contents from bank 0 and a user defined ?window? that can be located anywhere in the data memory space. the value of fsr2 establishes the lower bound- ary of the addresses mapped into the window, while the upper boundary is defined by fsr2 plus 95 (5fh). addresses in the access ram above 5fh are mapped as previously described (see section 5.3.2 ?access bank? ). an example of access bank remapping in this addressing mode is shown in figure 5-9. remapping of the access bank applies only to opera- tions using the indexed literal offset mode. operations that use the bsr (access ram bit is ? 1 ?) will continue to use direct addressing as before. any indirect or indexed operation that explicitly uses any of the indirect file operands (including fsr2) will continue to operate as standard indirect addressing. any instruction that uses the access bank, but includes a register address of greater than 05fh, will use direct addressing and the normal access bank map. 5.6.4 bsr in indexed literal offset mode although the access bank is remapped when the extended instruction set is enabled, the operation of the bsr remains unchanged. direct addressing, using the bsr to select the data memory bank, operates in the same manner as previously described. figure 5-9: remapping the access bank with indexed literal offset addressing data memory 000h 100h 200h f60h f00h fffh bank 1 bank 15 bank 2 through bank 14 sfrs 05fh addwf f, d, a fsr2h:fsr2l = 120h locations in the region from the fsr2 pointer (120h) to the pointer plus 05fh (17fh) are mapped to the bottom of the access ram (000h-05fh). special file registers at f60h through fffh are mapped to 60h through ffh, as usual. bank 0 addresses below 5fh are not available in this mode. they can still be addressed by using the bsr. access bank 00h ffh bank 0 sfrs bank 1 ?window? not accessible window example situation: 120h 17fh 5fh 60h
? 2004 microchip technology inc. preliminary ds39629b-page 87 PIC18F6390/6490/8390/8490 6.0 flash program memory in PIC18F6390/6490/8390/8490 devices, the program memory is implemented as read-only flash memory. it is readable over the entire v dd range during normal operation. a read from program memory is executed on one byte at a time. 6.1 table reads for pic18 devices, there are two operations that allow the processor to move bytes between the program memory space and the data ram: table read ( tblrd ) and table write ( tblwt ). table read operations retrieve data from program memory and place it into the data ram space. figure 6-1 shows the operation of a table read with program memory and data ram. the program memory space is 16 bits wide, while the data ram space is 8 bits wide. table reads and table writes move data between these two memory spaces through an 8-bit register, tablat. table reads work with byte entities. a table block containing data, rather than program instructions, is not required to be word-aligned. therefore, a table block can start and end at any byte address. because the program memory cannot be written to or erased under normal operation, the tblwt operation is not discussed here. figure 6-1: table read operation note 1: although it cannot be used in PIC18F6390/6490/8390/8490 devices in normal operation, the tblwt instruction is still implemented in the instruction set. executing the instruction takes two instruction cycles, but effectively results in a nop . 2: the tblwt instruction is available only in programming modes and is used during in-circuit serial programming? (icsp?). table pointer (1) table latch (8-bit) program memory tblptrh tblptrl tablat tblptru instruction: tblrd * note 1: table pointer register points to a byte in program memory. program memory (tblptr)
PIC18F6390/6490/8390/8490 ds39629b-page 88 preliminary ? 2004 microchip technology inc. 6.2 control registers two control registers are used in conjunction with the tblrd instruction: the tablat register and the tblptr register set. 6.2.1 table latch register (tablat) the table latch (tablat) is an 8-bit register mapped into the sfr space. the table latch register is used to hold 8-bit data during data transfers between program memory and data ram. 6.2.2 table pointer register (tblptr) the table pointer register (tblptr) addresses a byte within the program memory. it is comprised of three sfr registers: table pointer upper byte, table pointer high byte and table pointer low byte (tblptru:tblptrh:tblptrl). only the lower six bits of tblptru are used with tblptrh and tblptrl to form a 22-bit wide pointer. the contents of tblptr indicates a location in program memory space. the low-order 21 bits allow the device to address the full 2 mbytes of program memory space. the 22nd bit allows access to the configuration space, including the device id, user id locations and the configuration bits. the tblptr register set is updated when executing a tblrd in one of four ways, based on the instruction?s arguments. these are detailed in table 6-1. these operations on the tblptr only affect the low-order 21 bits. when a tblrd is executed, all 22 bits of the tblptr determine which byte is read from program memory into tablat. table 6-1: table pointer operations with tblrd instructions 6.3 reading the flash program memory the tblrd instruction is used to retrieve data from program memory and places it into data ram. table reads from program memory are performed one byte at a time. tblptr points to a byte address in program space. executing tblrd places the byte pointed to into tablat. in addition, tblptr can be modified automatically for the next table read operation. the internal program memory is typically organized by words. the least significant bit of the address selects between the high and low bytes of the word. figure 6-2 shows the interface between the internal program memory and the tablat. a typical method for reading data from program memory is shown in example 6-1. figure 6-2: reads from flash program memory example operation on table pointer tblrd* tblptr is not modified tblrd*+ tblptr is incremented after the read tblrd*- tblptr is decremented after the read tblrd+* tblptr is incremented before the read (even byte address) program memory (odd byte address) tblrd tablat tblptr = xxxxx1 fetch instruction register (ir) read register tblptr = xxxxx0
? 2004 microchip technology inc. preliminary ds39629b-page 89 PIC18F6390/6490/8390/8490 example 6-1: reading a flash program memory word table 6-2: registers associated with reading program flash memory movlw code_addr_upper ; load tblptr with the base movwf tblptru ; address of the word movlw code_addr_high movwf tblptrh movlw code_addr_low movwf tblptrl read_word tblrd*+ ; read into tablat and increment movf tablat, w ; get data movwf word_even tblrd*+ ; read into tablat and increment movf tablat, w ; get data movf word_odd name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page tblptru ? ? bit 21 program memory table pointer upper byte (tblptr<20:16>) 59 tblptrh program memory table pointer high byte (tblptr<15:8>) 59 tblptrl program memory table pointer low byte (tblptr<7:0>) 59 tablat program memory table latch 59 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used during flash access.
PIC18F6390/6490/8390/8490 ds39629b-page 90 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 91 PIC18F6390/6490/8390/8490 7.0 8 x 8 hardware multiplier 7.1 introduction all pic18 devices include an 8 x 8 hardware multiplier as part of the alu. the multiplier performs an unsigned operation and yields a 16-bit result that is stored in the product register pair prodh:prodl. the multiplier?s operation does not affect any flags in the status register. making multiplication a hardware operation allows it to be completed in a single instruction cycle. this has the advantages of higher computational throughput and reduced code size for multiplication algorithms and allows the pic18 devices to be used in many applications previously reserved for digital signal processors. a comparison of various hardware and software multiply operations, along with the savings in memory and execution time, is shown in table 7-1. 7.2 operation example 7-1 shows the instruction sequence for an 8 x 8 unsigned multiplication. only one instruction is required when one of the arguments is already loaded in the wreg register. example 7-2 shows the sequence to do an 8 x 8 signed multiplication. to account for the signed bits of the arguments, each argument?s most significant bit (msb) is tested and the appropriate subtractions are done. example 7-1: 8 x 8 unsigned multiply routine example 7-2: 8 x 8 signed multiply routine table 7-1: performance comparison for various multiply operations movf arg1, w ; mulwf arg2 ; arg1 * arg2 -> ; prodh:prodl movf arg1, w mulwf arg2 ; arg1 * arg2 -> ; prodh:prodl btfsc arg2, sb ; test sign bit subwf prodh, f ; prodh = prodh ; - arg1 movf arg2, w btfsc arg1, sb ; test sign bit subwf prodh, f ; prodh = prodh ; - arg2 routine multiply method program memory (words) cycles (max) time @ 40 mhz @ 10 mhz @ 4 mhz 8 x 8 unsigned without hardware multiply 13 69 6.9 s27.6 s69 s hardware multiply 1 1 100 ns 400 ns 1 s 8 x 8 signed without hardware multiply 33 91 9.1 s36.4 s91 s hardware multiply 6 6 600 ns 2.4 s6 s 16 x 16 unsigned without hardware multiply 21 242 24.2 s96.8 s 242 s hardware multiply 28 28 2.8 s 11.2 s28 s 16 x 16 signed without hardware multiply 52 254 25.4 s 102.6 s 254 s hardware multiply 35 40 4.0 s16.0 s40 s
PIC18F6390/6490/8390/8490 ds39629b-page 92 preliminary ? 2004 microchip technology inc. example 7-3 shows the sequence to do a 16 x 16 unsigned multiplication. equation 7-1 shows the algorithm that is used. the 32-bit result is stored in four registers (res3:res0). equation 7-1: 16 x 16 unsigned multiplication algorithm example 7-3: 16 x 16 unsigned multiply routine example 7-4 shows the sequence to do a 16 x 16 signed multiply. equation 7-2 shows the algorithm used. the 32-bit result is stored in four registers (res3:res0). to account for the signed bits of the arguments, the msb for each argument pair is tested and the appropriate subtractions are done. equation 7-2: 16 x 16 signed multiplication algorithm example 7-4: 16 x 16 signed multiply routine res3:res0 = arg1h:arg1l ? arg2h:arg2l = (arg1h ? arg2h ? 2 16 ) + (arg1h ? arg2l ? 2 8 ) + (arg1l ? arg2h ? 2 8 ) + (arg1l ? arg2l) movf arg1l, w mulwf arg2l ; arg1l * arg2l-> ; prodh:prodl movff prodh, res1 ; movff prodl, res0 ; ; movf arg1h, w mulwf arg2h ; arg1h * arg2h-> ; prodh:prodl movff prodh, res3 ; movff prodl, res2 ; ; movf arg1l, w mulwf arg2h ; arg1l * arg2h-> ; prodh:prodl movf prodl, w ; addwf res1, f ; add cross movf prodh, w ; products addwfc res2, f ; clrf wreg ; addwfc res3, f ; ; movf arg1h, w ; mulwf arg2l ; arg1h * arg2l-> ; prodh:prodl movf prodl, w ; addwf res1, f ; add cross movf prodh, w ; products addwfc res2, f ; clrf wreg ; addwfc res3, f ; res3:res0= arg1h:arg1l ? arg2h:arg2l = (arg1h ? arg2h ? 2 16 ) + (arg1h ? arg2l ? 2 8 ) + (arg1l ? arg2h ? 2 8 ) + (arg1l ? arg2l) + (-1 ? arg2h<7> ? arg1h:arg1l ? 2 16 ) + (-1 ? arg1h<7> ? arg2h:arg2l ? 2 16 ) movf arg1l, w mulwf arg2l ; arg1l * arg2l -> ; prodh:prodl movff prodh, res1 ; movff prodl, res0 ; ; movf arg1h, w mulwf arg2h ; arg1h * arg2h -> ; prodh:prodl movff prodh, res3 ; movff prodl, res2 ; ; movf arg1l, w mulwf arg2h ; arg1l * arg2h -> ; prodh:prodl movf prodl, w ; addwf res1, f ; add cross movf prodh, w ; products addwfc res2, f ; clrf wreg ; addwfc res3, f ; ; movf arg1h, w ; mulwf arg2l ; arg1h * arg2l -> ; prodh:prodl movf prodl, w ; addwf res1, f ; add cross movf prodh, w ; products addwfc res2, f ; clrf wreg ; addwfc res3, f ; ; btfss arg2h, 7 ; arg2h:arg2l neg? bra sign_arg1 ; no, check arg1 movf arg1l, w ; subwf res2 ; movf arg1h, w ; subwfb res3 ; sign_arg1 btfss arg1h, 7 ; arg1h:arg1l neg? bra cont_code ; no, done movf arg2l, w ; subwf res2 ; movf arg2h, w ; subwfb res3 ; cont_code :
? 2004 microchip technology inc. preliminary ds39629b-page 93 PIC18F6390/6490/8390/8490 8.0 interrupts the PIC18F6390/6490/8390/8490 devices have multi- ple interrupt sources and an interrupt priority feature that allows most interrupt sources to be assigned a high priority level or a low priority level. the high priority interrupt vector is at 0008h and the low priority interrupt vector is at 0018h. high priority interrupt events will interrupt any low priority interrupts that may be in progress. there are thirteen registers which are used to control interrupt operation. these registers are: rcon intcon intcon2 intcon3 pir1, pir2, pir3 pie1, pie2, pie3 ipr1, ipr2, ipr3 it is recommended that the microchip header files supplied with mplab ? ide be used for the symbolic bit names in these registers. this allows the assembler/ compiler to automatically take care of the placement of these bits within the specified register. in general, interrupt sources have three bits to control their operation. they are: flag bit to indicate that an interrupt event occurred enable bit that allows program execution to branch to the interrupt vector address when the flag bit is set priority bit to select high priority or low priority the interrupt priority feature is enabled by setting the ipen bit (rcon<7>). when interrupt priority is enabled, there are two bits which enable interrupts globally. setting the gieh bit (intcon<7>) enables all interrupts that have the priority bit set (high priority). setting the giel bit (intcon<6>) enables all interrupts that have the priority bit cleared (low priority). when the interrupt flag, enable bit and appropriate global interrupt enable bit are set, the interrupt will vector immediately to address 0008h or 0018h, depending on the priority bit setting. individual interrupts can be disabled through their corresponding enable bits. when the ipen bit is cleared (default state), the interrupt priority feature is disabled and interrupts are compatible with picmicro ? mid-range devices. in compatibility mode, the interrupt priority bits for each source have no effect. intcon<6> is the peie bit, which enables/disables all peripheral interrupt sources. intcon<7> is the gie bit, which enables/disables all interrupt sources. all interrupts branch to address 0008h in compatibility mode. when an interrupt is responded to, the global interrupt enable bit is cleared to disable further interrupts. if the ipen bit is cleared, this is the gie bit. if interrupt priority levels are used, this will be either the gieh or giel bit. high priority interrupt sources can interrupt a low priority interrupt. low priority interrupts are not processed while high priority interrupts are in progress. the return address is pushed onto the stack and the pc is loaded with the interrupt vector address (0008h or 0018h). once in the interrupt service routine, the source(s) of the interrupt can be determined by polling the interrupt flag bits. the interrupt flag bits must be cleared in software before re-enabling interrupts to avoid recursive interrupts. the ?return from interrupt? instruction, retfie , exits the interrupt routine and sets the gie bit (gieh or giel if priority levels are used), which re-enables interrupts. for external interrupt events, such as the int pins or the portb input change interrupt, the interrupt latency will be three to four instruction cycles. the exact latency is the same for one or two-cycle instructions. individual interrupt flag bits are set, regardless of the status of their corresponding enable bit or the gie bit. note: do not use the movff instruction to modify any of the interrupt control registers while any interrupt is enabled. doing so may cause erratic microcontroller behavior.
PIC18F6390/6490/8390/8490 ds39629b-page 94 preliminary ? 2004 microchip technology inc. figure 8-1: pic18f6x90/8x90 interrupt logic tmr0ie gieh/gie giel/peie wake-up if in interrupt to cpu vector to location 0008h int2if int2ie int2ip int1if int1ie int1ip tmr0if tmr0ie tmr0ip rbif rbie rbip ipen tmr0if tmr0ip int1if int1ie int1ip int2if int2ie int2ip rbif rbie rbip int0if int0ie giel/peie interrupt to cpu vector to location ipen ipe 0018h pir1<6:0> pie1<6:0> ipr1<6:0> high priority interrupt generation low priority interrupt generation idle or sleep modes gieh/gie int3if int3ie int3ip int3if int3ie int3ip pir2<7:6, 3:0> pie2<7:6, 3:0> ipr2<7:6, 3:0> pir3<6:4> pie3<6:4> ipr3<6:4> pir1<6:0> pie1<6:0> ipr1<6:0> pir2<7:6, 3:0> pie2<7:6, 3:0> ipr2<7:6, 3:0> pir3<6:4> pie3<6:4> ipr3<6:4> ipen
? 2004 microchip technology inc. preliminary ds39629b-page 95 PIC18F6390/6490/8390/8490 8.1 intcon registers the intcon registers are readable and writable registers which contain various enable, priority and flag bits. register 8-1: intcon: interrupt control register note: interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global interrupt enable bit. user software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. this feature allows for software polling. r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-x gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif bit 7 bit 0 bit 7 gie/gieh: global interrupt enable bit when ipen = 0 : 1 = enables all unmasked interrupts 0 = disables all interrupts when ipen = 1 : 1 = enables all high priority interrupts 0 = disables all interrupts bit 6 peie/giel: peripheral interrupt enable bit when ipen = 0 : 1 = enables all unmasked peripheral interrupts 0 = disables all peripheral interrupts when ipen = 1 : 1 = enables all low priority peripheral interrupts 0 = disables all low priority peripheral interrupts bit 5 tmr0ie: tmr0 overflow interrupt enable bit 1 = enables the tmr0 overflow interrupt 0 = disables the tmr0 overflow interrupt bit 4 int0ie: int0 external interrupt enable bit 1 = enables the int0 external interrupt 0 = disables the int0 external interrupt bit 3 rbie: rb port change interrupt enable bit 1 = enables the rb port change interrupt 0 = disables the rb port change interrupt bit 2 tmr0if: tmr0 overflow interrupt flag bit 1 = tmr0 register has overflowed (must be cleared in software) 0 = tmr0 register did not overflow bit 1 int0if: int0 external interrupt flag bit 1 = the int0 external interrupt occurred (must be cleared in software) 0 = the int0 external interrupt did not occur bit 0 rbif: rb port change interrupt flag bit 1 = at least one of the rb7:rb4 pins changed state (must be cleared in software) 0 = none of the rb7:rb4 pins have changed state note: a mismatch condition will continue to set this bit. reading portb will end the mismatch condition and allow the bit to be cleared. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 96 preliminary ? 2004 microchip technology inc. register 8-2: intcon2: interrupt control register 2 r/w-1 r/w-1 r/w-1 r/w-1 r/w-1 r/w-1 r/w-1 r/w-1 rbpu intedg0 intedg1 intedg2 i ntedg3 tmr0ip int3ip rbip bit 7 bit 0 bit 7 rbpu : portb pull-up enable bit 1 = all portb pull-ups are disabled 0 = portb pull-ups are enabled by individual port latch values bit 6 intedg0: external interrupt 0 edge select bit 1 = interrupt on rising edge 0 = interrupt on falling edge bit 5 intedg1: external interrupt 1 edge select bit 1 = interrupt on rising edge 0 = interrupt on falling edge bit 4 intedg2: external interrupt 2 edge select bit 1 = interrupt on rising edge 0 = interrupt on falling edge bit 3 intedg3: external interrupt 3 edge select bit 1 = interrupt on rising edge 0 = interrupt on falling edge bit 2 tmr0ip: tmr0 overflow interrupt priority bit 1 = high priority 0 = low priority bit 1 int3ip: int3 external interrupt priority bit 1 = high priority 0 = low priority bit 0 rbip: rb port change interrupt priority bit 1 = high priority 0 = low priority legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown note: interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global interrupt enable bit. user software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. this feature allows for software polling.
? 2004 microchip technology inc. preliminary ds39629b-page 97 PIC18F6390/6490/8390/8490 register 8-3: intcon3: interrupt control register 3 r/w-1 r/w-1 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 int2ip int1ip int3ie int2ie int1ie int3if int2if int1if bit 7 bit 0 bit 7 int2ip: int2 external interrupt priority bit 1 = high priority 0 = low priority bit 6 int1ip: int1 external interrupt priority bit 1 = high priority 0 = low priority bit 5 int3ie: int3 external interrupt enable bit 1 = enables the int3 external interrupt 0 = disables the int3 external interrupt bit 4 int2ie: int2 external interrupt enable bit 1 = enables the int2 external interrupt 0 = disables the int2 external interrupt bit 3 int1ie: int1 external interrupt enable bit 1 = enables the int1 external interrupt 0 = disables the int1 external interrupt bit 2 int3if: int3 external interrupt flag bit 1 = the int3 external interrupt occurred (must be cleared in software) 0 = the int3 external interrupt did not occur bit 1 int2if: int2 external interrupt flag bit 1 = the int2 external interrupt occurred (must be cleared in software) 0 = the int2 external interrupt did not occur bit 0 int1if: int1 external interrupt flag bit 1 = the int1 external interrupt occurred (must be cleared in software) 0 = the int1 external interrupt did not occur legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown note: interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global interrupt enable bit. user software should ensure the appropriate interrupt flag bits are clear prior to enabling an inter- rupt. this feature allows for software polling.
PIC18F6390/6490/8390/8490 ds39629b-page 98 preliminary ? 2004 microchip technology inc. 8.2 pir registers the pir registers contain the individual flag bits for the peripheral interrupts. due to the number of peripheral interrupt sources, there are three peripheral interrupt request (flag) registers (pir1, pir2, pir3). register 8-4: pir1: peripheral interrupt request (flag) register 1 note 1: interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global interrupt enable bit, gie (intcon<7>). 2: user software should ensure the appropriate interrupt flag bits are cleared prior to enabling an interrupt and after servicing that interrupt. u-0 r/w-0 r-0 r-0 r/w-0 r/w-0 r/w-0 r/w-0 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if bit 7 bit 0 bit 7 unimplemented: read as ? 0 ? bit 6 adif: a/d converter interrupt flag bit 1 = an a/d conversion completed (must be cleared in software) 0 = the a/d conversion is not complete bit 5 rc1if: eusart receive interrupt flag bit 1 = the eusart receive buffer, rc1reg, is full (cleared when rc1reg is read) 0 = the eusart receive buffer is empty bit 4 tx1if: eusart transmit interrupt flag bit 1 = the eusart transmit buffer, tx1reg, is empty (cleared when tx1reg is written) 0 = the eusart transmit buffer is full bit 3 sspif: master synchronous serial port interrupt flag bit 1 = the transmission/reception is complete (must be cleared in software) 0 = waiting to transmit/receive bit 2 ccp1if: ccp1 interrupt flag bit capture mode: 1 = a tmr1/tmr3 register capture occurred (must be cleared in software) 0 = no tmr1/tmr3 register capture occurred compare mode: 1 = a tmr1/tmr3 register compare match occurred (must be cleared in software) 0 = no tmr1/tmr3 register compare match occurred pwm mode: unused in this mode. bit 1 tmr2if: tmr2 to pr2 match interrupt flag bit 1 = tmr2 to pr2 match occurred (must be cleared in software) 0 = no tmr2 to pr2 match occurred bit 0 tmr1if: tmr1 overflow interrupt flag bit 1 = tmr1 register overflowed (must be cleared in software) 0 = tmr1 register did not overflow legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
? 2004 microchip technology inc. preliminary ds39629b-page 99 PIC18F6390/6490/8390/8490 register 8-5: pir2: peripheral interrupt request (flag) register 2 r/w-0 r/w-0 u-0 u-0 r/w-0 r/w-0 r/w-0 r/w-0 oscfif cmif ? ? bclif hlvdif tmr3if ccp2if bit 7 bit 0 bit 7 oscfif: oscillator fail interrupt flag bit 1 = device oscillator failed, clock input has changed to intosc (must be cleared in software) 0 = device clock operating bit 6 cmif: comparator interrupt flag bit 1 = comparator input has changed (must be cleared in software) 0 = comparator input has not changed bit 5-4 unimplemented: read as ? 0 ? bit 3 bclif: bus collision interrupt flag bit 1 = a bus collision occurred (must be cleared in software) 0 = no bus collision occurred bit 2 hlvdif: high/low-voltage detect interrupt flag bit 1 = a low-voltage condition occurred (must be cleared in software) 0 = the device voltage is above the low-voltage detect trip point bit 1 tmr3if: tmr3 overflow interrupt flag bit 1 = tmr3 register overflowed (must be cleared in software) 0 = tmr3 register did not overflow bit 0 ccp2if: ccp2 interrupt flag bit capture mode: 1 = a tmr1/tmr3 register capture occurred (must be cleared in software) 0 = no tmr1/tmr3 register capture occurred compare mode: 1 = a tmr1/tmr3 register compare match occurred (must be cleared in software) 0 = no tmr1/tmr3 register compare match occurred pwm mode: unused in this mode. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 100 preliminary ? 2004 microchip technology inc. register 8-6: pir3: peripheral interrupt request (flag) register 3 u-0 r/w-0 r-0 r-0 u-0 u-0 u-0 u-0 ? lcdif rc2if tx2if ? ? ? ? bit 7 bit 0 bit 7 unimplemented: read as ? 0 ? bit 6 lcdif: lcd interrupt flag bit (valid when type-b waveform with non-static mode is selected) 1 = lcd data of all coms is output (must be cleared in software) 0 = lcd data of all coms is not yet output bit 5 rc2if: ausart receive interrupt flag bit 1 = the ausart receive buffer, rc2reg, is full (cleared when rc2reg is read) 0 = the ausart receive buffer is empty bit 4 tx2if: ausart transmit interrupt flag bit 1 = the ausart transmit buffer, tx2reg, is empty (cleared when tx2reg is written) 0 = the ausart transmit buffer is full bit 3-0 unimplemented: read as ? 0 ? legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
? 2004 microchip technology inc. preliminary ds39629b-page 101 PIC18F6390/6490/8390/8490 8.3 pie registers the pie registers contain the individual enable bits for the peripheral interrupts. due to the number of peripheral interrupt sources, there are three peripheral interrupt enable registers (pie1, pie2, pie3). when ipen = 0 , the peie bit must be set to enable any of these peripheral interrupts. register 8-7: pie1: peripheral interrupt enable register 1 u-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie bit 7 bit 0 bit 7 unimplemented: read as ? 0 ? bit 6 adie: a/d converter interrupt enable bit 1 = enables the a/d interrupt 0 = disables the a/d interrupt bit 5 rc1ie: eusart receive interrupt enable bit 1 = enables the eusart receive interrupt 0 = disables the eusart receive interrupt bit 4 tx1ie: eusart transmit interrupt enable bit 1 = enables the eusart transmit interrupt 0 = disables the eusart transmit interrupt bit 3 sspie: master synchronous serial port interrupt enable bit 1 = enables the mssp interrupt 0 = disables the mssp interrupt bit 2 ccp1ie: ccp1 interrupt enable bit 1 = enables the ccp1 interrupt 0 = disables the ccp1 interrupt bit 1 tmr2ie: tmr2 to pr2 match interrupt enable bit 1 = enables the tmr2 to pr2 match interrupt 0 = disables the tmr2 to pr2 match interrupt bit 0 tmr1ie: tmr1 overflow interrupt enable bit 1 = enables the tmr1 overflow interrupt 0 = disables the tmr1 overflow interrupt legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 102 preliminary ? 2004 microchip technology inc. register 8-8: pie2: peripheral interrupt enable register 2 r/w-0 r/w-0 u-0 u-0 r/w-0 r/w-0 r/w-0 r/w-0 oscfie cmie ? ? bclie hlvdie tmr3ie ccp2ie bit 7 bit 0 bit 7 oscfie: oscillator fail interrupt enable bit 1 = enabled 0 =disabled bit 6 cmie: comparator interrupt enable bit 1 = enabled 0 =disabled bit 5-4 unimplemented: read as ? 0 ? bit 3 bclie: bus collision interrupt enable bit 1 = enabled 0 =disabled bit 2 hlvdie: high/low-voltage detect interrupt enable bit 1 = enabled 0 =disabled bit 1 tmr3ie: tmr3 overflow interrupt enable bit 1 = enabled 0 =disabled bit 0 ccp2ie: ccp2 interrupt enable bit 1 = enabled 0 =disabled legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
? 2004 microchip technology inc. preliminary ds39629b-page 103 PIC18F6390/6490/8390/8490 register 8-9: pie3: peripheral interrupt enable register 3 u-0 r/w-0 r-0 r-0 u-0 u-0 u-0 u-0 ? lcdie rc2ie tx2ie ? ? ? ? bit 7 bit 0 bit 7 unimplemented: read as ? 0 ? bit 6 lcdie: lcd interrupt enable bit (valid when type-b wa veform with non-static mode is selected) 1 = enabled 0 = disabled bit 5 rc2ie: ausart receive interrupt enable bit 1 = enabled 0 = disabled bit 4 tx2ie: ausart transmit interrupt enable bit 1 = enabled 0 = disabled bit 3-0 unimplemented: read as ? 0 ? legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 104 preliminary ? 2004 microchip technology inc. 8.4 ipr registers the ipr registers contain the individual priority bits for the peripheral interrupts. due to the number of peripheral interrupt sources, there are three peripheral interrupt priority registers (ipr1, ipr2, ipr3). using the priority bits requires that the interrupt priority enable (ipen) bit be set. register 8-10: ipr1: peripheral interrupt priority register 1 u-0 r/w-1 r/w-1 r/w-1 r/w-1 r/w-1 r/w-1 r/w-1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip bit 7 bit 0 bit 7 unimplemented: read as ? 0 ? bit 6 adip: a/d converter interrupt priority bit 1 =high priority 0 = low priority bit 5 rc1ip: eusart receive interrupt priority bit 1 =high priority 0 = low priority bit 4 tx1ip: eusart transmit interrupt priority bit 1 =high priority 0 = low priority bit 3 sspip: master synchronous serial port interrupt priority bit 1 =high priority 0 = low priority bit 2 ccp1ip: ccp1 interrupt priority bit 1 =high priority 0 = low priority bit 1 tmr2ip: tmr2 to pr2 match interrupt priority bit 1 =high priority 0 = low priority bit 0 tmr1ip: tmr1 overflow interrupt priority bit 1 =high priority 0 = low priority legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
? 2004 microchip technology inc. preliminary ds39629b-page 105 PIC18F6390/6490/8390/8490 register 8-11: ipr2: peripheral interrupt priority register 2 r/w-1 r/w-1 u-0 u-0 r/w-1 r/w-1 r/w-1 r/w-1 oscfip cmip ? ? bclip hlvdip tmr3ip ccp2ip bit 7 bit 0 bit 7 oscfip: oscillator fail interrupt priority bit 1 =high priority 0 = low priority bit 6 cmip: comparator interrupt priority bit 1 =high priority 0 = low priority bit 5-4 unimplemented: read as ? 0 ? bit 3 bclip: bus collision interrupt priority bit 1 =high priority 0 = low priority bit 2 hlvdip: high/low-voltage detect interrupt priority bit 1 =high priority 0 = low priority bit 1 tmr3ip: tmr3 overflow interrupt priority bit 1 =high priority 0 = low priority bit 0 ccp2ip: ccp2 interrupt priority bit 1 =high priority 0 = low priority legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 106 preliminary ? 2004 microchip technology inc. register 8-12: ipr3: peripheral interrupt priority register 3 u-0 r/w-0 r-0 r-0 u-0 u-0 u-0 u-0 ? lcdip rc2ip tx2ip ? ? ? ? bit 7 bit 0 bit 7 unimplemented: read as ? 0 ? bit 6 lcdip: lcd interrupt priority bit (valid when type-b wa veform with non-static mode is selected) 1 = high priority 0 = low priority bit 5 rc2ip: ausart receive priority flag bit 1 = high priority 0 = low priority bit 4 tx2ip: ausart transmit interrupt priority bit 1 = high priority 0 = low priority bit 3-0 unimplemented: read as ? 0 ? legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
? 2004 microchip technology inc. preliminary ds39629b-page 107 PIC18F6390/6490/8390/8490 8.5 rcon register the rcon register contains bits used to determine the cause of the last reset or wake-up from idle or sleep modes. rcon also contains the bit that enables interrupt priorities (ipen). register 8-13: rcon: reset control re gister r/w-0 r/w-1 u-0 r/w-1 r-1 r-1 r/w-0 r/w-0 ipen sboren ?ri to pd por bor bit 7 bit 0 bit 7 ipen: interrupt priority enable bit 1 = enable priority levels on interrupts 0 = disable priority levels on interrupts (pic16cxxx compatibility mode) bit 6 sboren: software bor enable bit for details of bit operation and reset state, see register 4-1. bit 5 unimplemented: read as ? 0 ? bit 4 ri : reset instruction flag bit for details of bit operation, see register 4-1. bit 3 to : watchdog timer time-out flag bit for details of bit operation, see register 4-1. bit 2 pd : power-down detection flag bit for details of bit operation, see register 4-1. bit 1 por : power-on reset status bit for details of bit operation, see register 4-1. bit 0 bor : brown-out reset status bit for details of bit operation, see register 4-1. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 108 preliminary ? 2004 microchip technology inc. 8.6 intn pin interrupts external interrupts on the rb0/int0, rb1/int1, rb2/ int2 and rb3/int3 pins are edge-triggered. if the corresponding intedgx bit in the intcon2 register is set (= 1 ), the interrupt is triggered by a rising edge; if the bit is clear, the trigger is on the falling edge. when a valid edge appears on the rbx/intx pin, the corresponding flag bit intxf is set. this interrupt can be disabled by clearing the corresponding enable bit, intxe. the interrupt flag bit must be cleared in software in the interrupt service routine before re-enabling the interrupt. all external interrupts (int0, int1, int2 and int3) can wake-up the processor from the power managed modes if bit intxe was set prior to going into power managed modes. if the global interrupt enable bit, gie, is set, the processor will branch to the interrupt vector following wake-up. interrupt priority for int1, int2 and int3 is determined by the value contained in the interrupt priority bits, int1ip (intcon3<6>), int2ip (intcon3<7>) and int3ip (intcon2<1>). there is no priority bit associated with int0. it is always a high priority interrupt source. 8.7 tmr0 interrupt in 8-bit mode (which is the default), an overflow in the tmr0 register (ffh 00h) will set flag bit tmr0if. in 16-bit mode, an overflow in the tmr0h:tmr0l regis- ter pair (ffffh 0000h) will set tmr0if. the interrupt can be enabled/disabled by setting/clearing enable bit, tmr0ie (intcon<5>). interrupt priority for timer0 is determined by the value contained in the interrupt priority bit, tmr0ip (intcon2<2>). see section 10.0 ?timer0 module? for further details on the timer0 module. 8.8 portb interrupt-on-change an input change on portb<7:4> sets flag bit, rbif (intcon<0>). the interrupt can be enabled/disabled by setting/clearing enable bit, rbie (intcon<3>). interrupt priority for portb interrupt-on-change is determined by the value contained in the interrupt priority bit, rbip (intcon2<0>). 8.9 context saving during interrupts during interrupts, the return pc address is saved on the stack. additionally, the wreg, status and bsr registers are saved on the fast return stack. if a fast return from interrupt is not used (see section 5.3 ?data memory organization? ), the user may need to save the wreg, status and bsr registers on entry to the interrupt service routine. depending on the user?s application, other registers may also need to be saved. example 8-1 saves and restores the wreg, status and bsr registers during an interrupt service routine. example 8-1: saving status, wreg and bsr registers in ram movwf w_temp ; w_temp is in virtual bank movff status, status_temp ; status_temp located anywhere movff bsr, bsr_temp ; bsr_tmep located anywhere ; ; user isr code ; movff bsr_temp, bsr ; restore bsr movf w_temp, w ; restore wreg movff status_temp, status ; restore status
? 2004 microchip technology inc. preliminary ds39629b-page 109 PIC18F6390/6490/8390/8490 9.0 i/o ports depending on the device selected and features enabled, there are up to nine ports available. some pins of the i/o ports are multiplexed with an alternate function from the peripheral features on the device. in general, when a peripheral is enabled, that pin may not be used as a general purpose i/o pin. each port has three registers for its operation. these registers are: tris register (data direction register) port register (reads the levels on the pins of the device) lat register (output latch) the data latch (lat register) is useful for read-modify-write operations on the value that the i/o pins are driving. a simplified model of a generic i/o port, without the interfaces to other peripherals, is shown in figure 9-1. figure 9-1: generic i/o port operation 9.1 porta, trisa and lata registers porta is an 8-bit wide, bidirectional port. the corre- sponding data direction register is trisa. setting a trisa bit (= 1 ) will make the corresponding porta pin an input (i.e., put the corresponding output driver in a high-impedance mode). clearing a trisa bit (= 0 ) will make the corresponding porta pin an output (i.e., put the contents of the output latch on the selected pin). reading the porta register reads the status of the pins, whereas writing to it will write to the port latch. the data latch register (lata) is also memory mapped. read-modify-write operations on the lata register read and write the latched output value for porta. the ra4 pin is multiplexed with the timer0 module clock input and the lcd segment drive to become the ra4/t0cki/seg14 pin. pins ra6 and ra7 are multiplexed with the main oscillator pins; they are enabled as oscillator or i/o pins by the selection of the main oscillator in the configuration register (see section 23.1 ?configuration bits? for details). when they are not used as port pins, ra6 and ra7 and their associated tris and lat bits are read as ? 0 ?. the other porta pins are multiplexed with analog inputs and the analog v ref + and v ref - inputs. the operation of pins ra3:ra0 and ra5 as a/d converter inputs is selected by clearing or setting the control bits in the adcon1 register (a/d control register 1). pins ra0 through ra5 may also be used as comparator inputs or outputs by setting the appropriate bits in the cmcon register. to use ra3:ra0 as digital inputs, it is also necessary to turn off the comparators. the ra4/t0cki/seg14 pin is a schmitt trigger input and an open-drain output. all other porta pins have ttl input levels and full cmos output drivers. the trisa register controls the direction of the porta pins, even when they are being used as analog inputs. the user must ensure the bits in the trisa register are maintained set when using them as analog inputs. ra5:ra2 are also multiplexed with lcd segment drives controlled by bits in the lcdse1 and lcdse2 registers. i/o port functions are only available when the segments are disabled. example 9-1: initializing porta data bus wr lat wr tris rd port data latch tris latch rd tris input buffer i/o pin (1) q d ck q d ck en qd en rd lat or port note 1: i/o pins have diode protection to v dd and v ss . note: on a power-on reset, ra5 and ra3:ra0 are configured as analog inputs and read as ? 0 ?. ra4 is configured as a digital input. clrf porta ; initialize porta by ; clearing output ; data latches clrf lata ; alternate method ; to clear output ; data latches movlw 07h ; configure a/d movwf adcon1 ; for digital inputs movwf 07h ; configure comparators movwf cmcon ; for digital input movlw 0cfh ; value used to ; initialize data ; direction movwf trisa ; set ra<3:0> as inputs ; ra<5:4> as outputs
PIC18F6390/6490/8390/8490 ds39629b-page 110 preliminary ? 2004 microchip technology inc. table 9-1: porta functions pin name function tris setting i/o buffer description ra0/an0 ra0 0 o dig lata<0> data output. not affected by analog pin setting. 1 i ttl porta<0> data input. reads ? 0 ? on por. an0 1 i ana a/d input channel 0. default configuration on por. ra1/an1 ra1 0 o dig lata<1> data output. not affected by analog pin setting. 1 i ttl porta<1> data input. reads ? 0 ? on por. an1 1 i ana a/d input channel 1. default configuration on por. ra2/an2/v ref -/s eg16 ra2 0 o dig lata<2> data output. not affected by analog pin setting; disabled when lcd segment enabled. 1 i ttl porta<2> data input. reads ? 0 ? on por. an2 1 i ana a/d input channel 2. default configuration on por. v ref - 1 i ana a/d low reference voltage input. seg16 x o ana segment 16 analog output for lcd. ra3/an3/v ref +/ seg17 ra3 0 o dig lata<3> data output. output in unaffected by analog pin setting; disabled when lcd segment enabled. 1 i ttl porta<3> data input. reads ? 0 ? on por. an3 1 i ana a/d input channel 3. default configuration on por. v ref + 1 i ana a/d high reference voltage input. seg17 x o ana segment 17 analog output for lcd. disables all other digital outputs. ra4/t0cki/ seg14 ra4 0 o dig lata<4> data output; disabled when lcd segment enabled. 1 i st porta<4> data input. t0cki i st timer0 clock input. seg14 x o ana segment 14 analog output for lcd. ra5/an4/ hlvdin/seg15 ra5 0 o dig lata<5> data output. not affected by analog pin setting; disabled when lcd segment enabled. 1 i ttl porta<5> data input. reads ? 0 ? on por. an4 1 i ana a/d input channel 5. default configuration on por. hlvdin 1 i ana high/low-voltage detect external trip point input. seg15 x o ana segment 15 analog output for lcd. osc2/clko/ra6 osc2 x o ana main oscillator feedback output connection (xt, hs and lp modes). clko x o dig system cycle clock output (f osc /4) in all oscillator modes except rcio, intio2 and ecio. ra6 0 o dig lata<6> data output. enabled in rcio, intio2 and ecio modes only. 1 i ttl porta<6> data input. enabled in rcio, intio2 and ecio modes only. osc1/clki/ra7 osc1 x i ana main oscillator input connec tion, all modes except intio. clki x i ana main clock input connection, all modes except intio. ra7 0 o dig lata<7> data output. available only in intio modes; otherwise reads as ? 0 ?. 1 i ttl porta<7> data input. available only in intio modes; otherwise reads as ? 0 ?. legend: pwr = power supply, o = output, i = input, ana = analog signal, dig = digital output, st = schmitt buffer input, ttl = ttl buffer input, x = don?t care (tris bit does not affect port direction or is overridden for this option).
? 2004 microchip technology inc. preliminary ds39629b-page 111 PIC18F6390/6490/8390/8490 table 9-2: summary of registers associated with porta name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page porta ra7 (1) ra6 (1) ra5 ra4 ra3 ra2 ra1 ra0 62 lata lata7 (1) lata6 (1) lata data output register 62 trisa trisa7 (1) trisa6 (1) porta data direction register 62 adcon1 ? ? vcfg1 vcfg0 pcfg3 pcfg2 pcfg1 pcfg0 61 lcdse1 se15 se14 se13 se12 se11 se10 se9 se8 64 lcdse2 se23 se22 se21 se20 se19 se18 se17 se16 64 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used by porta. note 1: ra7:ra6 and their associated latch and data direction bits are enabled as i/o pins based on oscillator configuration; otherwise, they are read as ? 0 ?.
PIC18F6390/6490/8390/8490 ds39629b-page 112 preliminary ? 2004 microchip technology inc. 9.2 portb, trisb and latb registers portb is an 8-bit wide, bidirectional port. the corre- sponding data direction register is trisb. setting a trisb bit (= 1 ) will make the corresponding portb pin an input (i.e., put the corresponding output driver in a high-impedance mode). clearing a trisb bit (= 0 ) will make the corresponding portb pin an output (i.e., put the contents of the output latch on the selected pin). the data latch register (latb) is also memory mapped. read-modify-write operations on the latb register read and write the latched output value for portb. example 9-2: initializing portb each of the portb pins has a weak internal pull-up. a single control bit can turn on all the pull-ups. this is performed by clearing bit rbpu (intcon2<7>). the weak pull-up is automatically turned off when the port pin is configured as an output. the pull-ups are disabled on a power-on reset. four of the portb pins (rb7:rb4) have an interrupt-on-change feature. only pins configured as inputs can cause this interrupt to occur (i.e., any rb7:rb4 pin configured as an output is excluded from the interrupt-on-change comparison). the input pins (of rb7:rb4) are compared with the old value latched on the last read of portb. the ?mismatch? outputs of rb7:rb4 are ored together to generate the rb port change interrupt with flag bit, rbif (intcon<0>). this interrupt can wake the device from power managed modes. the user, in the interrupt service routine, can clear the interrupt in the following manner: a) any read or write of portb (except with the movff (any), portb instruction). this will end the mismatch condition. b) clear flag bit rbif. a mismatch condition will continue to set flag bit rbif. reading portb will end the mismatch condition and allow flag bit rbif to be cleared. the interrupt-on-change feature is recommended for wake-up on key depression operation and operations where portb is only used for the interrupt-on-change feature. polling of portb is not recommended while using the interrupt-on-change feature. rb4:rb1 are also multiplexed with lcd segment drives controlled by bits in the lcdse1 register. i/o port functions are only available when the segments are disabled. clrf portb ; initialize portb by ; clearing output ; data latches clrf latb ; alternate method ; to clear output ; data latches movlw 0cfh ; value used to ; initialize data ; direction movwf trisb ; set rb<3:0> as inputs ; rb<5:4> as outputs ; rb<7:6> as inputs
? 2004 microchip technology inc. preliminary ds39629b-page 113 PIC18F6390/6490/8390/8490 table 9-3: portb functions pin name function tris setting i/o buffer description rb0/int0 rb0 0 o dig latb<0> data output. 1 i ttl portb<0> data input; programmable weak pull-up. int0 1 i st external interrupt 0 input. rb1/int1/seg8 rb1 0 o dig latb<1> data output; disabled when lcd segment enabled. 1 i ttl portb<1> data input; weak pull-up when rbpu bit is cleared. int1 1 i st external interrupt 1 input. seg8 x o ana segment 8 analog output for lcd. disables digital output. rb2/int2/seg9 rb2 0 o dig latb<2> data output; disabled when lcd segment enabled. 1 i ttl portb<2> data input; weak pull-up when rbpu bit is cleared. int2 1 i st external interrupt 2 input. seg9 x o ana segment 9 analog output for lcd rb3/int3/ seg10 rb3 0 o dig latb<3> data output; disabled when lcd segment enabled. 1 i ttl portb<3> data input; weak pull-up when rbpu bit is cleared. int3 1 i st external interrupt 3 input. seg10 x o ana segment 10 analog output for lcd. rb4/kbi0/ seg11 rb4 0 o dig latb<4> data output; disabled when lcd segment enabled. 1 i ttl portb<4> data input; weak pull-up when rbpu bit is cleared. kbi0 1 i ttl interrupt on pin change. seg11 x o ana segment 11 analog output for lcd. rb5/kbi1 rb5 0 o dig latb<5> data output; disabled when lcd segment enabled. 1 i ttl portb<5> data input; weak pull-up when rbpu bit is cleared. kbi1 1 i ttl interrupt on pin change. rb6/kbi2/pgc rb6 0 o dig latb<6> data output; unavailable when icd or icsp? enabled. 1 i ttl portb<6> data input; unavailable when icd or icsp enabled. kbi2 1 i ttl interrupt on pin change; unavailable when icd or icsp enabled. pgc x i st serial execution (icsp) clock input for icsp and icd operation. (1) rb7/kbi3/pgd rb7 0 o dig latb<7> data output; unavailable when icd or icsp enabled. 1 i ttl portb<7> data input; unavailable when icd or icsp enabled. kbi3 1 i ttl interrupt on pin change; unavailable when icd or icsp enabled. pgd x o dig serial execution data output for icsp and icd operation. (1) x i st serial execution data input for icsp and icd operation. (1) legend: pwr = power supply, o = output, i = input, ana = analog signal, dig = digital output, st = schmitt buffer input, ttl = ttl buffer input, x = don?t care (tris bit does not affect port direction or is overridden for this option). note 1: all other pin functions are disabl ed when icsp or icd are enabled.
PIC18F6390/6490/8390/8490 ds39629b-page 114 preliminary ? 2004 microchip technology inc. table 9-4: summary of registers associated with portb name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page portb rb7 rb6 rb5 rb4 rb3 rb2 rb1 rb0 62 latb latb data output register 62 trisb portb data direction register 62 intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 intcon2 rbpu intedg0 intedg1 intedg2 intedg3 tmr0ip int3ip rbip 59 intcon3 int2ip int1ip int3ie int2ie int1ie int3if int2if int1if 59 lcdse1 se15 se14 se13 se12 se11 se10 se9 se8 64 legend: shaded cells are not used by portb.
? 2004 microchip technology inc. preliminary ds39629b-page 115 PIC18F6390/6490/8390/8490 9.3 portc, trisc and latc registers portc is an 8-bit wide, bidirectional port. the corre- sponding data direction register is trisc. setting a trisc bit (= 1 ) will make the corresponding portc pin an input (i.e., put the corresponding output driver in a high-impedance mode). clearing a trisc bit (= 0 ) will make the corresponding portc pin an output (i.e., put the contents of the output latch on the selected pin). the data latch register (latc) is also memory mapped. read-modify-write operations on the latc register read and write the latched output value for portc. portc is multiplexed with several peripheral functions (table 9-5). the pins have schmitt trigger input buffers. rc1 is normally configured by configuration bit ccp2mx as the default peripheral pin of the ccp2 module (default/erased state, ccp2mx = 1 ). when enabling peripheral functions, care should be taken in defining tris bits for each portc pin. some peripherals override the tris bit to make a pin an output, while other peripherals override the tris bit to make a pin an input. the user should refer to the corresponding peripheral section for the correct tris bit settings. the contents of the trisc register are affected by peripheral overrides. reading trisc always returns the current contents, even though a peripheral device may be overriding one or more of the pins. rc2 and rc5 are also multiplexed with lcd segment drives controlled by bits in the lcdse1 register. i/o port functions are only available when the segments are disabled. example 9-3: initializing portc note: on a power-on reset, these pins are configured as digital inputs. clrf portc ; initialize portc by ; clearing output ; data latches clrf latc ; alternate method ; to clear output ; data latches movlw 0cfh ; value used to ; initialize data ; direction movwf trisc ; set rc<3:0> as inputs ; rc<5:4> as outputs ; rc<7:6> as inputs
PIC18F6390/6490/8390/8490 ds39629b-page 116 preliminary ? 2004 microchip technology inc. table 9-5: portc functions pin name function tris setting i/o buffer description rc0/t1oso/ t13cki/ rc0 0 o dig latc<0> data output; disabled when timer1 oscillator is used. 1 i st portc<0> data input; disabled when timer1 oscillator is used. t1oso x o ana timer1 oscillator output. t13cki x i st timer1/timer3 clock input. rc1/t1osi/ ccp2 rc1 0 o dig latc<1> data output; disabled when timer1 oscillator is used. 1 i st portc<1> data input; disabled when timer1 oscillator is used. t1osi x i ana timer1 oscillator input. ccp2 (1) 0 o dig ccp2 compare output or pwm output; takes priority over digital i/o data. 1 i st ccp2 capture input. rc2/ccp1/ seg13 rc2 0 o dig latc<2> data output; disabled when lcd segment enabled. 1 i st portc<2> data input. ccp1 0 o dig ccp1 compare output or pwm output; takes priority over digital i/o data. 1 i st ccp1 capture input. seg13 x o ana segment 13 analog output for lcd. rc3/sck/scl rc3 0 o dig latc<3> data output. 1 i st portc<3> data input. sck 0 o dig spi? clock output (mssp module); takes priority over port data. 1 i st spi clock input (mssp module). scl 0 odigi 2 c? clock output (mssp module); takes priority over port data. 1 isti 2 c clock input (mssp module); input type depends on module setting. rc4/sdi/sda rc4 0 o dig latc<4> data output. 1 i st portc<4> data input. sdi 1 i st spi data input (mssp module). sda 1 odigi 2 c data output (mssp module); takes priority over port data. 1 isti 2 c data input (mssp module); input type depends on module setting. rc5/sdo/ seg12 rc5 0 o dig latc<5> data output; disabled when lcd segment enabled. 1 i st portc<5> data input. sdo 0 o dig spi data output (mssp module); takes priority over port data. seg12 x o ana segment 12 analog output for lcd. rc6/tx1/ck1 rc6 0 o dig latc<6> data output. 1 i st portc<6> data input. tx1 1 o dig synchronous serial data output (eusart module); takes priority over port data. ck1 1 o dig synchronous serial data input (eusart module). user must configure as an input. 1 i st synchronous serial clock input (eusart module). rc7/rx1/dt1 rc7 0 o dig latc<7> data output. 1 i st portc<7> data input. rx1 1 i st asynchronous serial receive data input (eusart module). dt1 1 o dig synchronous serial data output (eusart module); takes priority over port data. 1 i st synchronous serial data input (eu sart module). user must configure as an input. legend: pwr = power supply, o = output, i = input, ana = analog signal, dig = digital output, st = schmitt buffer input, ttl = ttl buffer input, x = don?t care (tris bit does not affect port direction or is overridden for this option). note 1: default assignment for ccp2 (configuration bit ccp2mx = 1 ).
? 2004 microchip technology inc. preliminary ds39629b-page 117 PIC18F6390/6490/8390/8490 table 9-6: summary of registers associated with portc name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page portc rc7 rc6 rc5 rc4 rc3 rc2 rc1 rc0 62 latc latc data output register 62 trisc portc data direction register 62 lcdse1 se15 se14 se13 se12 se11 se10 se9 se8 64 legend: shaded cells are not used by portc.
PIC18F6390/6490/8390/8490 ds39629b-page 118 preliminary ? 2004 microchip technology inc. 9.4 portd, trisd and latd registers portd is an 8-bit wide, bidirectional port. the corre- sponding data direction register is trisd. setting a trisd bit (= 1 ) will make the corresponding portd pin an input (i.e., put the corresponding output driver in a high-impedance mode). clearing a trisd bit (= 0 ) will make the corresponding portd pin an output (i.e., put the contents of the output latch on the selected pin). the data latch register (latd) is also memory mapped. read-modify-write operations on the latd register read and write the latched output value for portd. all pins on portd are implemented with schmitt trigger input buffers. each pin is individually configurable as an input or output. portd is also multiplexed with lcd segment drives controlled by the lcdse0 register. i/o port functions are only available when the segments are disabled. example 9-4: initializing portd table 9-7: portd functions note: on a power-on reset, these pins are configured as digital inputs. clrf portd ; initialize portd by ; clearing output ; data latches clrf latd ; alternate method ; to clear output ; data latches movlw 0cfh ; value used to ; initialize data ; direction movwf trisd ; set rd<3:0> as inputs ; rd<5:4> as outputs ; rd<7:6> as inputs pin name function tris setting i/o buffer description rd0/seg0 rd0 0 o dig latd<0> data output; disabled when lcd segment enabled. 1 i st portd<0> data input. seg0 x o ana segment 0 analog output for lcd. rd1/seg1 rd1 0 o dig latd<1> data output; disabled when lcd segment enabled. 1 i st portd<1> data input. seg1 x o ana segment 1 analog output for lcd. rd2/seg2 rd2 0 o dig latd<2> data output; disabled when lcd segment enabled. 1 i st portd<2> data input. seg2 x o ana segment 2 analog output for lcd. rd3/seg3 rd3 0 o dig latd<3> data output; disabled when lcd segment enabled. 1 i st portd<3> data input. seg3 x o ana segment 3 analog output for lcd. rd4/seg4 rd4 0 o dig latd<4> data output; disabled when lcd segment enabled. 1 i st portd<4> data input. seg4 x o ana segment 4 analog output for lcd module. rd5/seg5 rd5 0 o dig latd<5> data output; disabled when lcd segment enabled. 1 i st portd<5> data input. seg5 x o ana segment 5 analog output for lcd. rd6/seg6 rd6 0 o dig latd<6> data output; disabled when lcd segment enabled. 1 i st portd<6> data input. seg6 x o ana segment 6 analog output for lcd. rd7/seg7 rd7 0 o dig latd<7> data output; disabled when lcd segment enabled. 1 i st portd<7> data input. seg7 x o ana segment 7 analog output for lcd. legend: pwr - power supply, o - output, i - input, ana - analog signal, dig - digital output, st - schmitt buffer input, ttl - ttl buffer input, x = don?t care (tris bit does not affect port direction or is overridden for this option).
? 2004 microchip technology inc. preliminary ds39629b-page 119 PIC18F6390/6490/8390/8490 table 9-8: summary of registers associated with portd name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page portd rd7 rd6 rd5 rd4 rd3 rd2 rd1 rd0 62 latd latd data output register 62 trisd portd data direction register 62 lcdse0 se7 se6 se5 se4 se3 se2 se1 se0 64
PIC18F6390/6490/8390/8490 ds39629b-page 120 preliminary ? 2004 microchip technology inc. 9.5 porte, trise and late registers porte is a 4-bit wide, bidirectional port. the corre- sponding data direction register is trise. setting a trise bit (= 1 ) will make the corresponding porte pin an input (i.e., put the corresponding output driver in a high-impedance mode). clearing a trise bit (= 0 ) will make the corresponding porte pin an output (i.e., put the contents of the output latch on the selected pin). the data latch register (late) is also memory mapped. read-modify-write operations on the late register read and write the latched output value for porte. all pins on porte are implemented with schmitt trigger input buffers. each pin is individually configurable as an input or output. pins re6:re4 are multiplexed with three of the lcd common drives. i/o port functions are only available on those porte pins, depending on which commons are active. the configuration is determined by the lmux1:lmux0 control bits (lcdcon<1:0>). the availability is summarized in table 9-9. re7 is also multiplexed with lcd segment drive (seg31) controlled by the lcdse3<7> bit. i/o port function is only available when the segment is disabled. re7 also can be configured as the alternate peripheral pin for the ccp2 module. this is done by clearing the ccp2mx configuration bit. table 9-9: porte pins available in different lcd drive configurations example 9-5: initializing porte note: on a power-on reset, these pins are configured as digital inputs. note: the pins corresponding to re2:re0 of other pic18f parts have the function of lcdbias3:lcdbias1 and the pin corresponding to re3 of other pic18f parts has the function of com0. these four pins cannot be used as digital i/o. lcdcon <1:0> active lcd commons porte available for i/o 00 com0 re6, re5, re4 01 com0, com1 re6, re5 10 com0, com1 and com2 re6 11 all (com0 through com3) none clrf porte ; initialize porte by ; clearing output ; data latches clrf late ; alternate method ; to clear output ; data latches movlw 30h ; value used to ; initialize data ; direction movwf trise ; set re<5:4> as inputs ; re<7:6> as outputs
? 2004 microchip technology inc. preliminary ds39629b-page 121 PIC18F6390/6490/8390/8490 table 9-10: porte functions table 9-11: summary of registers associated with porte pad name function tris setting i/o buffer description re4/com1 re4 0 o dig late<4> data output; disabled when lcd common enabled. 1 i st porte<4> data input. com1 x o ana common 1 analog output for lcd. re5/com2 re5 0 o dig late<5> data output; disabled when lcd common enabled. 1 i st porte<5> data input. com2 x o ana common 2 analog output for lcd. re6/com3 re6 0 o dig late<6> data output; disabled when lcd segment enabled. 1 i st porte<6> data input. com3 x o ana common 3 analog output for lcd. re7/ccp2/ seg31 re7 0 o dig late<7> data output; disabled when lcd segment enabled. 1 i st porte<7> data input. ccp2 (1) 0 o dig ccp2 compare output and ccp2 pwm output; takes priority over port data. 1 i st ccp2 capture input. seg31 x o ana segment 31 analog output for lcd. legend: pwr = power supply, o = output, i = input, ana = analog signal, dig = digital output, st = schmitt buffer input, ttl = ttl buffer input, x = don?t care (tris bit does not affect port direction or is overridden for this option). note 1: alternate assignment for ccp2 when configuration bit ccp2mx = 0 . name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page porte re7 re6 re5 re4 ? ? ? ?62 late late data output register ? ? ? ?62 trise porte data direction bits ? ? ? ?62 lcdcon lcden slpen werr ? cs1 cs0 lmux1 lmux0 64 lcdse3 se31 se30 se29 se28 se27 se26 se25 se24 64 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used by porte.
PIC18F6390/6490/8390/8490 ds39629b-page 122 preliminary ? 2004 microchip technology inc. 9.6 portf, latf and trisf registers portf is an 8-bit wide, bidirectional port. the corre- sponding data direction register is trisf. setting a trisf bit (= 1 ) will make the corresponding portf pin an input (i.e., put the corresponding output driver in a high-impedance mode). clearing a trisf bit (= 0 ) will make the corresponding portf pin an output (i.e., put the contents of the output latch on the selected pin). the data latch register (latf) is also memory mapped. read-modify-write operations on the latf register read and write the latched output value for portf. all pins on portf are implemented with schmitt trigger input buffers. each pin is individually configurable as an input or output. portf is multiplexed with several analog peripheral functions, including the a/d converter inputs and comparator inputs, outputs and voltage reference. portf is also multiplexed with lcd segment drives controlled by bits in the lcdse2 and lcdse3 registers. i/o port functions are only available when the segments are disabled. example 9-6: initializing portf note 1: on a power-on reset, the rf6:rf0 pins are configured as inputs and read as ? 0 ?. 2: to configure portf as digital i/o, turn off comparators and set adcon1 value. clrf portf ; initialize portf by ; clearing output ; data latches clrf latf ; alternate method ; to clear output ; data latches movlw 0x07 ; movwf cmcon ; turn off comparators movlw 0x0f ; movwf adcon1 ; set portf as digital i/o movlw 0xcf ; value used to ; initialize data ; direction movwf trisf ; set rf3:rf0 as inputs ; rf5:rf4 as outputs ; rf7:rf6 as inputs
? 2004 microchip technology inc. preliminary ds39629b-page 123 PIC18F6390/6490/8390/8490 table 9-12: portf functions pin name function tris setting i/o buffer description rf0/an5/ seg18 rf0 0 o dig latf<0> data output. output is unaffected by analog input; disabled when lcd segment is enabled. 1 i st portf<0> data input. reads ? 0 ? on por. an5 1 i ana a/d input channel 5. default configuration on por. seg18 x o ana segment 18 analog output for lcd. rf1/an6/ c2out/seg19 rf1 0 o dig latf<1> data output. output is unaffected by analog input; disabled when lcd segment is enabled. 1 i st portf<1> data input. reads ? 0 ? on por. an6 1 i ana a/d input channel 6. default configuration on por. c2out 0 o dig comparator 2 output; takes priority over port data. seg19 x o ana segment 19 analog output for lcd. rf2/an7/ c1out/seg20 rf2 0 o dig latf<2> data output. output is unaffected by analog input; disabled when lcd segment is enabled. 1 i st portf<2> data input. reads ? 0 ? on por. an7 1 i ana a/d input channel 7. default configuration on por. c1out 0 o ttl comparator 1 output; takes priority over port data. seg20 x o ana segment 20 analog output for lcd. rf3/an8/ seg21 rf3 0 o dig latf<3> data output. output is unaffected by analog input; disabled when lcd segment is enabled. 1 i st portf<3> data input. reads ? 0 ? on por. an8 1 i ana a/d input channel 8 and comparator c2+ input. default input configuration on por; not affected by analog output. seg21 x o ana segment 21 analog output for lcd. rf4/an9/ seg22 rf4 0 o dig latf<4> data output. output is unaffected by analog input; disabled when lcd segment is enabled. 1 i st portf<4> data input. reads ? 0 ? on por. an9 1 i ana a/d input channel 9 and comparator c2- input. default input configuration on por; does not affect digital output. seg22 x o ana segment 22 analog output for lcd. rf5/an10/ cv ref /seg23 rf5 0 o dig latf<5> data output. output unaffected by analog input; disabled when either lcd segment or cv ref is enabled. 1 i st portf<5> data input. reads ? 0 ? on por. an10 1 i ana a/d input channel 10 and comparator c1+ input. default input configuration on por. cv ref 0 o ana comparator voltage reference output . enabling this feature disables digital i/o. seg23 x o ana segment 23 analog output for lcd. rf6/an11/ seg24 rf6 0 o dig latf<6> data output. output unaffected by analog input; disabled when lcd segment is enabled. 1 i st portf<6> data input. reads ? 0 ? on por. an11 1 i ana a/d input channel 11 and comparator c1- input. default input configuration on por; does not affect digital output. seg24 x o ana segment 24 analog output for lcd. rf7/ss /seg25 rf7 0 o dig latf<7> data output; disabled when lcd segment is enabled. 1 i st portf<7> data input. ss 1 i ttl slave select input for ssp (mssp module). seg25 x o ana segment 25 analog output for lcd. legend: pwr = power supply, o = output, i = input, ana = analog signal, dig = digital output, st = schmitt buffer input, ttl = ttl buffer input, x = don?t care (tris bit does not affect port direction or is overridden for this option).
PIC18F6390/6490/8390/8490 ds39629b-page 124 preliminary ? 2004 microchip technology inc. table 9-13: summary of registers associated with portf name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page trisf portf data direction control register 62 portf read portf pin/write portf data latch 62 latf read portf data latch/write portf data latch 62 adcon1 ? ? vcfg1 vcfg0 pcfg3 pcfg2 pcfg1 pcfg0 61 cmcon c2out c1out c2inv c1inv cis cm2 cm1 cm0 61 cvrcon cvren cvroe cvrr cvrss cvr3 cvr2 cvr1 cvr0 61 lcdse2 se23 se22 se21 se20 se19 se18 se17 se16 64 lcdse3 se31 se30 se29 se28 se27 se26 se25 se24 64 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used by portf.
? 2004 microchip technology inc. preliminary ds39629b-page 125 PIC18F6390/6490/8390/8490 9.7 portg, trisg and latg registers portg is a 6-bit wide, bidirectional port. the corre- sponding data direction register is trisg. setting a trisg bit (= 1 ) will make the corresponding portg pin an input (i.e., put the corresponding output driver in a high-impedance mode). clearing a trisg bit (= 0 ) will make the corresponding portg pin an output (i.e., put the contents of the output latch on the selected pin). the data latch register (latg) is also memory mapped. read-modify-write operations on the latg register read and write the latched output value for portg. portg is multiplexed with both usart and lcd functions (table 9-14). portg pins have schmitt trigger input buffers. when enabling peripheral functions, care should be taken in defining tris bits for each portg pin. some peripherals override the tris bit to make a pin an output, while other peripherals override the tris bit to make a pin an input. the user should refer to the corresponding peripheral section for the correct tris bit settings. the pin override value is not loaded into the tris register. this allows read-modify-write of the tris register without concern due to peripheral overrides. portg<4:0> are also multiplexed with lcd segment drives controlled by bits in the lcdse3 register. i/o port functions are only available when the segments are disabled. the sixth pin of portg (mclr /v pp /rg5) is an input only pin. its operation is controlled by the mclre configuration bit. when selected as a port pin (mclre = 0 ), it functions as a digital input only pin; as such, it does not have tris or lat bits associated with its operation. otherwise, it functions as the device?s master clear input. in either configuration, rg5 also functions as the programming voltage input during programming. example 9-7: initializing portg note: on a power-on reset, rg5 is enabled as a digital input only if master clear functionality is disabled. all other 5 pins are configured as digital inputs. clrf portg ; initialize portg by ; clearing output ; data latches clrf latg ; alternate method ; to clear output ; data latches movlw 0x04 ; value used to ; initialize data ; direction movwf trisg ; set rg1:rg0 as outputs ; rg2 as input ; rg4:rg3 as inputs
PIC18F6390/6490/8390/8490 ds39629b-page 126 preliminary ? 2004 microchip technology inc. table 9-14: portg functions table 9-15: summary of registers associated with portg pin name function tris setting i/o buffer description rg0/seg30 rg0 0 o dig latg<0> data output; disabled when lcd segment enabled. 1 i st portg<0> data input. seg30 x o ana segment 30 analog output for lcd. rg1/tx2/ck2/ seg29 rg1 0 o dig latg<1> data output; disabled when lcd segment enabled. 1 i st portg<1> data input. tx2 1 o dig synchronous serial data output (ausart module); takes priority over port data. ck2 1 o dig synchronous serial data input (ausart module). user must configure as an input. 1 i st synchronous serial clock input (ausart module). seg29 x o ana segment 29 analog output for lcd. rg2/rx2/dt2/ seg28 rg2 0 o dig latg<2> data output; disabled when lcd segment enabled. 1 i st portg<2> data input. rx2 1 i st asynchronous serial receive data input (ausart module). dt2 1 o dig synchronous serial data output (ausart module); takes priority over port data. 1 i st synchronous serial data input (ausart module). user must configure as an input. seg28 x o ana segment 28 analog output for lcd. rg3/seg27 rg3 0 o dig latg<3> data output; disabled when lcd segment enabled. 1 i st portg<3> data input. seg27 0 o ana segment 27 analog output for lcd. rg4/seg26 rg4 0 o dig latg<4> data output; disabled when lcd segment enabled. 1 i st portg<4> data input. seg26 x o ana segment 26 analog output for lcd. mclr /v pp /rg5 mclr ? (1) i st external master clear input; enabled when mclre configuration bit is set. v pp ? (1) i ana high-voltage detection; used for icsp? mode entry detection. always available, regardless of pin mode. rg5 ? (1) i st portg<5> data input; enabled when mclre configuration bit is clear. legend: pwr = power supply, o = output, i = input, ana = analog signal, dig = digital output, st = schmitt buffer input, ttl = ttl buffer input, x = don?t care (tris bit does not affect port direction or is overridden for this option). note 1: rg5 does not have a corresponding trisg bit. name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page portg ? ?rg5 (1) read portg pin/write portg data latch 62 latg ? ? ? latg data output register 62 trisg ? ? ? data direction control register for portg 62 lcdse3 se31 se30 se29 se28 se27 se26 se25 se24 64 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used by portg. note 1: rg5 is available as an input only when mclr is disabled.
? 2004 microchip technology inc. preliminary ds39629b-page 127 PIC18F6390/6490/8390/8490 9.8 porth, lath and trish registers porth is an 8-bit wide, bidirectional i/o port. the cor- responding data direction register is trish. setting a trish bit (= 1 ) will make the corresponding porth pin an input (i.e., put the corresponding output driver in a high-impedance mode). clearing a trish bit (= 0 ) will make the corresponding porth pin an output (i.e., put the contents of the output latch on the selected pin). the data latch register (lath) is also memory mapped. read-modify-write operations on the lath register read and write the latched output value for porth. all pins on porth are implemented with schmitt trigger input buffers. each pin is individually configurable as an input or output. porth is also multiplexed with lcd segment drives controlled by the lcdse5 register. i/o port functions are only available when the segments are disabled. example 9-8: initializing porth note: porth is available only on 80-pin devices. note: on a power-on reset, these pins are configured as digital inputs. clrf porth ; initialize porth by ; clearing output ; data latches clrf lath ; alternate method ; to clear output ; data latches movlw 0cfh ; value used to ; initialize data ; direction movwf trish ; set rh3:rh0 as inputs ; rh5:rh4 as outputs ; rh7:rh6 as inputs
PIC18F6390/6490/8390/8490 ds39629b-page 128 preliminary ? 2004 microchip technology inc. table 9-16: porth functions table 9-17: summary of registers associated with porth pin name function tris setting i/o buffer description rh0/seg47 rh0 0 o dig-4 lath<0> data output; disabled when lcd segment enabled. 1 i st porth<0> data input. seg47 x o ana segment 47 analog output for lcd. rh1/seg46 rh1 0 o dig lath<1> data output; disabled when lcd segment enabled. 1 i st porth<1> data input. seg46 x o ana segment 46 analog output for lcd. rh2/seg45 rh2 0 o dig lath<2> data output; disabled when lcd segment enabled. 1 i st porth<2> data input. seg45 x o ana segment 45 analog output for lcd. rh3/seg44 rh3 0 o dig lath<3> data output; disabled when lcd segment enabled. 1 i st porth<3> data input. seg44 x o ana segment 44 analog output for lcd. rh4/seg40 rh4 0 o dig lath<4> data output; disabled when lcd segment enabled. 1 i st porth<4> data input. seg40 x o ana segment 40 analog output for lcd rh5/seg41 rh5 0 o dig lath<5> data output; disabled when lcd segment enabled. 1 i st porth<5> data input. seg41 x o ana segment 41 analog output for lcd. rh6/seg42 rh6 0 o dig lath<6> data output; disabled when lcd segment enabled. 1 i st porth<6> data input. seg42 x o ana segment 42 analog output for lcd. rh7/seg43 rh7 0 o dig lath<7> data output; disabled when lcd segment enabled. 1 i st porth<7> data input. seg43 x o ana segment 43 analog output for lcd. legend: pwr = power supply, o = output, i = input, ana = analog signal, dig = digital output, st = schmitt buffer input, ttl = ttl buffer input, x = don?t care (tris bit does not affect port direction or is overridden for this option). name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page trish porth data direction control register 62 porth read porth pin/write porth data latch 62 lath read porth data latch/write porth data latch 62 lcdse5 se47 se46 se45 se44 se43 se42 se41 se40 64
? 2004 microchip technology inc. preliminary ds39629b-page 129 PIC18F6390/6490/8390/8490 9.9 portj, trisj and latj registers portj is an 8-bit wide, bidirectional port. the corre- sponding data direction register is trisj. setting a trisj bit (= 1 ) will make the corresponding portj pin an input (i.e., put the corresponding output driver in a high-impedance mode). clearing a trisj bit (= 0 ) will make the corresponding portj pin an output (i.e., put the contents of the output latch on the selected pin). the data latch register (latj) is also memory mapped. read-modify-write operations on the latj register read and write the latched output value for portj. all pins on portj are implemented with schmitt trigger input buffers. each pin is individually configurable as an input or output. portj is also multiplexed with lcd segment drives controlled by the lcdse4 register. i/o port functions are only available when the segments are disabled. example 9-9: initializing portj note: portj is available only on 80-pin devices. note: on a power-on reset, these pins are configured as digital inputs. clrf portj ; initialize portg by ; clearing output ; data latches clrf latj ; alternate method ; to clear output ; data latches movlw 0xcf ; value used to ; initialize data ; direction movwf trisj ; set rj3:rj0 as inputs ; rj5:rj4 as output ; rj7:rj6 as inputs
PIC18F6390/6490/8390/8490 ds39629b-page 130 preliminary ? 2004 microchip technology inc. table 9-18: portj functions table 9-19: summary of registers associated with portj pin name function tris setting i/o buffer description rj0/seg32 rj0 0 o dig latj<0> data output; disabled when lcd segment enabled. 1 i st portj<0> data input. seg32 x o ana segment 32 analog output for lcd. rj1/seg33 rj1 0 o dig latj<1> data output; disabled when lcd segment enabled. 1 i st portj<1> data input. seg33 x o ana segment 33 analog output for lcd. rj2/seg34 rj2 0 o dig latj<2> data output; disabled when lcd segment enabled. 1 i st portj<2> data input. seg34 x o ana segment 34 analog output for lcd. rj3/seg35 rj3 0 o dig latj<3> data output; disabled when lcd segment enabled. 1 i st portj<3> data input. seg35 x o ana segment 35 analog output for lcd. rj4/seg39 rj4 0 o dig latj<4> data output; disabled when lcd segment enabled. 1 i st portj<4> data input. seg39 x o ana segment 39 analog output for lcd. rj5/seg38 rj5 0 o dig latj<5> data output; disabled when lcd segment enabled. 1 i st portj<5> data input. seg38 x o ana segment 38 analog output for lcd. rj6/seg37 rj6 0 o dig latj<6> data output; disabled when lcd segment enabled. 1 i st portj<6> data input. seg37 x o ana segment 37 analog output for lcd. rj7/seg36 rj7 0 o dig latj<7> data output; disabled when lcd segment enabled. 1 i st portj<7> data input. seg36 x o ana segment 36 analog output for lcd. legend: pwr = power supply, o = output, i = input, ana = analog signal, dig = digital output, st = schmitt buffer input, ttl = ttl buffer input, x = don?t care (tris bit does not affect port direction or is overridden for this option). name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page portj read portj pin/write portj data latch 62 latj latj data output register 62 trisj data direction control register for portj 62 lcdse4 se39 se38 se37 se36 se35 se34 se33 se32 64
? 2004 microchip technology inc. preliminary ds39629b-page 131 PIC18F6390/6490/8390/8490 10.0 timer0 module the timer0 module incorporates the following features: software selectable operation as a timer or counter in both 8-bit or 16-bit modes readable and writable registers dedicated 8-bit software programmable prescaler selectable clock source (internal or external) edge select for external clock interrupt-on-overflow the t0con register (register 10-1) controls all aspects of the module?s operation, including the prescale selection. it is both readable and writable. a simplified block diagram of the timer0 module in 8-bit mode is shown in figure 10-1. figure 10-2 shows a simplified block diagram of the timer0 module in 16-bit mode. register 10-1: t0con: timer0 control register r/w-1 r/w-1 r/w-1 r/w-1 r/w-1 r/w-1 r/w-1 r/w-1 tmr0on t08bit t0cs t0se psa t0ps2 t0ps1 t0ps0 bit 7 bit 0 bit 7 tmr0on: timer0 on/off control bit 1 = enables timer0 0 = stops timer0 bit 6 t08bit : timer0 8-bit/16-bit control bit 1 = timer0 is configured as an 8-bit timer/counter 0 = timer0 is configured as a 16-bit timer/counter bit 5 t0cs : timer0 clock source select bit 1 = transition on t0cki pin 0 = internal instruction cycle clock (clko) bit 4 t0se : timer0 source edge select bit 1 = increment on high-to-low transition on t0cki pin 0 = increment on low-to-high transition on t0cki pin bit 3 psa : timer0 prescaler assignment bit 1 = timer0 prescaler is not assigned. timer0 clock input bypasses prescaler. 0 = timer0 prescaler is assigned. timer0 clock input comes from prescaler output. bit 2-0 t0ps2:t0ps0 : timer0 prescaler select bits 111 = 1:256 prescale value 110 = 1:128 prescale value 101 = 1:64 prescale value 100 = 1:32 prescale value 011 = 1:16 prescale value 010 = 1:8 prescale value 001 = 1:4 prescale value 000 = 1:2 prescale value legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 132 preliminary ? 2004 microchip technology inc. 10.1 timer0 operation timer0 can operate as either a timer or a counter; the mode is selected by clearing the t0cs bit (t0con<5>). in timer mode (t0cs = 0 ), the module increments on every clock by default, unless a different prescaler value is selected (see section 10.3 ?prescaler? ). if the tmr0 register is written to, the increment is inhibited for the following two instruction cycles. the user can work around this by writing an adjusted value to the tmr0 register. the counter mode is selected by setting the t0cs bit (= 1 ). in counter mode, timer0 increments either on every rising or falling edge of pin ra4/t0cki. the incrementing edge is determined by the timer0 source edge select bit, t0se (t0con<4>); clearing this bit selects the rising edge. restrictions on the external clock input are discussed below. an external clock source can be used to drive timer0; however, it must meet certain requirements to ensure that the external clock can be synchronized with the internal phase clock (t osc ). there is a delay between synchronization and the onset of incrementing the timer/counter. 10.2 timer0 reads and writes in 16-bit mode tmr0h is not the actual high byte of timer0 in 16-bit mode; it is actually a buffered version of the real high byte of timer0, which is not directly readable nor writable (refer to figure 10-2). tmr0h is updated with the contents of the high byte of timer0 during a read of tmr0l. this provides the ability to read all 16 bits of timer0, without having to verify that the read of the high and low byte were valid, due to a rollover between successive reads of the high and low byte. similarly, a write to the high byte of timer0 must also take place through the tmr0h buffer register. the high byte is updated with the contents of tmr0h when a write occurs to tmr0l. this allows all 16 bits of timer0 to be updated at once. figure 10-1: timer0 block diagram (8-bit mode) figure 10-2: timer0 block diagram (16-bit mode) note: upon reset, timer0 is enabled in 8-bit mode wit h clock input from t0cki maximum prescale. t0cki pin t0se 0 1 0 1 t0cs f osc /4 programmable prescaler sync with internal clocks tmr0l (2 t cy delay) internal data bus psa t0ps2:t0ps0 set tmr0if on overflow 3 8 8 note: upon reset, timer0 is enabled in 8-bit mode with clock input from t0cki maximum prescale. t0cki pin t0se 0 1 0 1 t0cs f osc /4 programmable prescaler sync with internal clocks tmr0l (2 t cy delay) internal data bus 8 psa t0ps2:t0ps0 set tmr0if on overflow 3 tmr0 tmr0h high byte 8 8 8 read tmr0l write tmr0l 8
? 2004 microchip technology inc. preliminary ds39629b-page 133 PIC18F6390/6490/8390/8490 10.3 prescaler an 8-bit counter is available as a prescaler for the timer0 module. the prescaler is not directly readable or writable; its value is set by the psa and t0ps2:t0ps0 bits (t0con<3:0>), which determine the prescaler assignment and prescale ratio. clearing the psa bit assigns the prescaler to the timer0 module. when it is assigned, prescale values from 1:2 through 1:256 in power-of-2 increments are selectable. when assigned to the timer0 module, all instructions writing to the tmr0 register (e.g., clrf tmr0 , movwf tmr0 , bsf tmr0 , etc.) clear the prescaler count. 10.3.1 switching prescaler assignment the prescaler assignment is fully under software control and can be changed ?on-the-fly? during program execution. 10.4 timer0 interrupt the tmr0 interrupt is generated when the tmr0 register overflows from ffh to 00h in 8-bit mode, or from ffffh to 0000h in 16-bit mode. this overflow sets the tmr0if flag bit. the interrupt can be masked by clearing the tmr0ie bit (intcon<5>). before re-enabling the interrupt, the tmr0if bit must be cleared in software by the interrupt service routine. since timer0 is shut down in sleep mode, the tmr0 interrupt cannot awaken the processor from sleep. table 10-1: registers associated with timer0 note: writing to tmr0 when the prescaler is assigned to timer0 will clear the prescaler count, but will not change the prescaler assignment. name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page tmr0l timer0 module low byte register 60 tmr0h timer0 module high byte register 60 intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 t0con tmr0on t08bit t0cs t0se psa t0ps2 t0ps1 t0ps0 60 trisa porta data direction register 62 legend: shaded cells are not used by timer0.
PIC18F6390/6490/8390/8490 ds39629b-page 134 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 135 PIC18F6390/6490/8390/8490 11.0 timer1 module the timer1 timer/counter module incorporates these features: software selectable operation as a 16-bit timer or counter readable and writable 8-bit registers (tmr1h and tmr1l) selectable clock source (internal or external) with device clock or timer1 oscillator internal options interrupt-on-overflow reset on ccp special event trigger device clock status flag (t1run) a simplified block diagram of the timer1 module is shown in figure 11-1. a block diagram of the module?s operation in read/write mode is shown in figure 11-2. the module incorporates its own low-power oscillator to provide an additional clocking option. the timer1 oscillator can also be used as a low-power clock source for the microcontroller in power managed operation. timer1 can also be used to provide real-time clock (rtc) functionality to applications with only a minimal addition of external components and code overhead. timer1 is controlled through the t1con control register (register 11-1). it also contains the timer1 oscillator enable bit (t1oscen). timer1 can be enabled or disabled by setting or clearing control bit, tmr1on (t1con<0>). register 11-1: t1con: timer1 control register r/w-0 r-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 rd16 t1run t1ckps1 t1ckps0 t1oscen t1sync tmr1cs tmr1on bit 7 bit 0 bit 7 rd16: 16-bit read/write mode enable bit 1 = enables register read/write of timer1 in one 16-bit operation 0 = enables register read/write of timer1 in two 8-bit operations bit 6 t1run: timer1 system clock status bit 1 = device clock is derived from timer1 oscillator 0 = device clock is derived from another source bit 5-4 t1ckps1:t1ckps0: timer1 input clock prescale select bits 11 = 1:8 prescale value 10 = 1:4 prescale value 01 = 1:2 prescale value 00 = 1:1 prescale value bit 3 t1oscen: timer1 oscillator enable bit 1 = timer1 oscillator is enabled 0 = timer1 oscillator is shut off the oscillator inverter and feedback resistor are turned off to eliminate power drain. bit 2 t1sync : timer1 external clock input synchronization select bit when tmr1cs = 1 : 1 = do not synchronize external clock input 0 = synchronize external clock input when tmr1cs = 0 : this bit is ignored. timer1 uses the internal clock when tmr1cs = 0 . bit 1 tmr1cs: timer1 clock source select bit 1 = external clock from pin rc0/t1oso/t13cki (on the rising edge) 0 = internal clock (f osc /4) bit 0 tmr1on: timer1 on bit 1 = enables timer1 0 = stops timer1 legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 136 preliminary ? 2004 microchip technology inc. 11.1 timer1 operation timer1 can operate in one of these modes: timer synchronous counter asynchronous counter the operating mode is determined by the clock select bit, tmr1cs (t1con<1>). when tmr1cs is cleared (= 0 ), timer1 increments on every internal instruction cycle (f osc /4). when the bit is set, timer1 increments on every rising edge of the timer1 external clock input or the timer1 oscillator, if enabled. when timer1 is enabled, the rc1/t1osi and rc0/t1oso/t13cki pins become inputs. this means the values of trisc<1:0> are ignored and the pins are read as ? 0 ?. figure 11-1: timer1 block diagram figure 11-2: timer1 block diagram (16-bit read/write mode) t1sync tmr1cs t1ckps1:t1ckps0 sleep input t1oscen (1) f osc /4 internal clock on/off prescaler 1, 2, 4, 8 synchronize detect 1 0 2 t1oso/t13cki t1osi 1 0 tmr1on tmr1l set tmr1if on overflow tmr1 high byte clear tmr1 (ccp special event trigger) timer1 oscillator note 1: when t1oscen is cleared, the inverter and feedback re sistor are turned off to eliminate power drain. on/off timer1 t1sync tmr1cs t1ckps1:t1ckps0 sleep input t1oscen (1) f osc /4 internal clock prescaler 1, 2, 4, 8 synchronize detect 1 0 2 t1oso/t13cki t1osi note 1: when t1oscen is cleared, the inverter and feedback resistor are turned off to eliminate power drain. 1 0 tmr1l internal data bus 8 set tmr1if on overflow tmr1 tmr1h high byte 8 8 8 read tmr1l write tmr1l 8 tmr1on clear tmr1 (ccp special event trigger) timer1 oscillator on/off timer1
? 2004 microchip technology inc. preliminary ds39629b-page 137 PIC18F6390/6490/8390/8490 11.2 timer1 16-bit read/write mode timer1 can be configured for 16-bit reads and writes (see figure 11-2). when the rd16 control bit (t1con<7>) is set, the address for tmr1h is mapped to a buffer register for the high byte of timer1. a read from tmr1l will load the contents of the high byte of timer1 into the timer1 high byte buffer register. this provides the user with the ability to accurately read all 16 bits of timer1 without having to determine whether a read of the high byte, followed by a read of the low byte, has become invalid due to a rollover between reads. a write to the high byte of timer1 must also take place through the tmr1h buffer register. the timer1 high byte is updated with the contents of tmr1h when a write occurs to tmr1l. this allows a user to write all 16 bits to both the high and low bytes of timer1 at once. the high byte of timer1 is not directly readable or writable in this mode. all reads and writes must take place through the timer1 high byte buffer register. writes to tmr1h do not clear the timer1 prescaler. the prescaler is only cleared on writes to tmr1l. 11.3 timer1 oscillator an on-chip crystal oscillator circuit is incorporated between pins t1osi (input) and t1oso (amplifier output). it is enabled by setting the timer1 oscillator enable bit, t1oscen (t1con<3>). the oscillator is a low-power circuit rated for 32 khz crystals. it will continue to run during all power managed modes. the circuit for a typical lp oscillator is shown in figure 11-3. table 11-1 shows the capacitor selection for the timer1 oscillator. the user must provide a software time delay to ensure proper start-up of the timer1 oscillator. figure 11-3: external components for the timer1 lp oscillator table 11-1: capacitor selection for the timer1 oscillator (2-4) 11.3.1 using timer1 as a clock source the timer1 oscillator is also available as a clock source in power managed modes. by setting the clock select bits, scs1:scs0 (osccon<1:0>), to ? 01 ?, the device switches to sec_run mode; both the cpu and peripherals are clocked from the timer1 oscillator. if the idlen bit (osccon<7>) is cleared and a sleep instruction is executed, the device enters sec_idle mode. additional details are available in section 3.0 ?power managed modes? . whenever the timer1 oscillator is providing the clock source, the timer1 system clock status flag, t1run (t1con<6>), is set. this can be used to determine the controller?s current clocking mode. it can also indicate the clock source being currently used by the fail-safe clock monitor. if the clock monitor is enabled and the timer1 oscillator fails while providing the clock, polling the t1run bit will indicate whether the clock is being provided by the timer1 oscillator or another source. 11.3.2 low-power timer1 option the timer1 oscillator can operate at two distinct levels of power consumption based on device configuration. when the lpt1osc configuration bit is set, the timer1 oscillator operates in a low-power mode. when lpt1osc is not set, timer1 operates at a higher power level. power consumption for a particular mode is relatively constant, regardless of the device?s operating mode. the default timer1 configuration is the higher power mode. as the low-power timer1 mode tends to be more sensitive to interference, high noise environments may cause some oscillator instability. the low-power option is therefore best suited for low noise applications where power conservation is an important design consideration. note: see the notes with table 11-1 for additional information about capacitor selection. c1 c2 xtal pic18fxxxx t1osi t1oso 32.768 khz 33 pf 33 pf osc type freq c1 c2 lp 32 khz 27 pf (1) 27 pf (1) note 1: microchip suggests these values as a starting point in validating the oscillator circuit. 2: higher capacitance increases the stability of the oscillator, but also increases the start-up time. 3: since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components. 4: capacitor values are for design guidance only.
PIC18F6390/6490/8390/8490 ds39629b-page 138 preliminary ? 2004 microchip technology inc. 11.3.3 timer1 oscillator layout considerations the timer1 oscillator circuit draws very little power during operation. due to the low-power nature of the oscillator, it may also be sensitive to rapidly changing signals in close proximity. the oscillator circuit, shown in figure 11-3, should be located as close as possible to the microcontroller. there should be no circuits passing within the oscillator circuit boundaries other than v ss or v dd . if a high-speed circuit must be located near the oscillator (such as the ccp1 pin in output compare or pwm mode, or the primary oscillator using the osc2 pin), a grounded guard ring around the oscillator circuit, as shown in figure 11-4, may be helpful when used on a single sided pcb or in addition to a ground plane. figure 11-4: oscillator circuit with grounded guard ring 11.4 timer1 interrupt the tmr1 register pair (tmr1h:tmr1l) increments from 0000h to ffffh and rolls over to 0000h. the timer1 interrupt, if enabled, is generated on overflow, which is latched in interrupt flag bit, tmr1if (pir1<0>). this interrupt can be enabled or disabled by setting or clearing the timer1 interrupt enable bit, tmr1ie (pie1<0>). 11.5 resetting timer1 using the ccp special event trigger if either of the ccp modules is configured in compare mode to generate a special event trigger (ccp1m3:ccp1m0 or ccp2m3:ccp2m0 = 1011 ), this signal will reset timer1. the trigger from ccp2 will also start an a/d conversion if the a/d module is enabled (see section 14.3.4 ?special event trigger? for more information.). the module must be configured as either a timer or a synchronous counter to take advantage of this feature. when used this way, the ccprh:ccprl register pair effectively becomes a period register for timer1. if timer1 is running in asynchronous counter mode, this reset operation may not work. in the event that a write to timer1 coincides with a special event trigger, the write operation will take precedence. 11.6 using timer1 as a real-time clock adding an external lp oscillator to timer1 (such as the one described in section 11.3 ?timer1 oscillator? , above) gives users the option to include rtc function- ality to their applications. this is accomplished with an inexpensive watch crystal to provide an accurate time base and several lines of application code to calculate the time. when operating in sleep mode and using a battery or supercapacitor as a power source, it can completely eliminate the need for a separate rtc device and battery backup. the application code routine, rtcisr , shown in example 11-1, demonstrates a simple method to increment a counter at one-second intervals using an interrupt service routine. incrementing the tmr1 register pair to overflow triggers the interrupt and calls the routine, which increments the seconds counter by one; additional counters for minutes and hours are incremented as the previous counter overflow. since the register pair is 16 bits wide, counting up to overflow the register directly from a 32.768 khz clock would take 2 seconds. to force the overflow at the required one-second intervals, it is necessary to preload it. the simplest method is to set the most sig- nificant bit of tmr1h with a bsf instruction. note that the tmr1l register is never preloaded or altered; doing so may introduce cumulative error over many cycles. for this method to be accurate, timer1 must operate in asynchronous mode and the timer1 overflow interrupt must be enabled (pie1<0> = 1 ), as shown in the routine, rtcinit . the timer1 oscillator must also be enabled and running at all times. v dd osc1 v ss osc2 rc0 rc1 rc2 note: not drawn to scale. note: the special event triggers from the ccp2 module will not set the tmr1if interrupt flag bit (pir1<0>).
? 2004 microchip technology inc. preliminary ds39629b-page 139 PIC18F6390/6490/8390/8490 example 11-1: implementing a real-time clock using a timer1 interrupt service table 11-2: registers associated with timer1 as a timer/counter rtcinit movlw 80h ; preload tmr1 register pair movwf tmr1h ; for 1 second overflow clrf tmr1l movlw b?00001111? ; configure for external clock, movwf t1osc ; asynchronous operation, external oscillator clrf secs ; initialize timekeeping registers clrf mins ; movlw .12 movwf hours bsf pie1, tmr1ie ; enable timer1 interrupt return rtcisr bsf tmr1h, 7 ; preload for 1 sec overflow bcf pir1, tmr1if ; clear interrupt flag incf secs, f ; increment seconds movlw .59 ; 60 seconds elapsed? cpfsgt secs return ; no, done clrf secs ; clear seconds incf mins, f ; increment minutes movlw .59 ; 60 minutes elapsed? cpfsgt mins return ; no, done clrf mins ; clear minutes incf hours, f ; increment hours movlw .23 ; 24 hours elapsed? cpfsgt hours return ; no, done movlw .01 ; reset hours to 1 movwf hours return ; done name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir1 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if 61 pie1 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie 61 ipr1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip 61 tmr1l holding register for the least significant byte of the 16-bit tmr1 register 60 tmr1h holding register for the most significant byte of the 16-bit tmr1 register 60 t1con rd16 t1run t1ckps1 t1ckps0 t1oscen t1sync tmr1cs tmr1on 60 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used by the timer1 module.
PIC18F6390/6490/8390/8490 ds39629b-page 140 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 141 PIC18F6390/6490/8390/8490 12.0 timer2 module the timer2 timer module incorporates the following features: 8-bit timer and period registers (tmr2 and pr2, respectively) readable and writable (both registers) software programmable prescaler (1:1, 1:4 and 1:16) software programmable postscaler (1:1 through 1:16) interrupt on tmr2-to-pr2 match optional use as the shift clock for the mssp module the module is controlled through the t2con register (register 12-1), which enables or disables the timer and configures the prescaler and postscaler. timer2 can be shut off by clearing control bit, tmr2on (t2con<2>), to minimize power consumption. a simplified block diagram of the module is shown in figure 12-1. 12.1 timer2 operation in normal operation, tmr2 is incremented from 00h on each clock (f osc /4). a 2-bit counter/prescaler on the clock input gives direct input, divide-by-4 and divide-by-16 prescale options; these are selected by the prescaler control bits, t2ckps1:t2ckps0 (t2con<1:0>). the value of tmr2 is compared to that of the period register, pr2, on each clock cycle. when the two values match, the comparator generates a match signal as the timer output. this signal also resets the value of tmr2 to 00h on the next cycle and drives the output counter/postscaler (see section 12.2 ?timer2 interrupt? ). the tmr2 and pr2 registers are both directly readable and writable. the tmr2 register is cleared on any device reset, while the pr2 register initializes at ffh. both the prescaler and postscaler counters are cleared on the following events: a write to the tmr2 register a write to the t2con register any device reset (power-on reset, mclr reset, watchdog timer reset, or brown-out reset) tmr2 is not cleared when t2con is written. register 12-1: t2con: time r2 control register u-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 ? t2outps3 t2outps2 t2outps1 t2outps0 tmr2on t2ckps1 t2ckps0 bit 7 bit 0 bit 7 unimplemented: read as ? 0 ? bit 6-3 t2outps3:t2outps0 : timer2 output postscale select bits 0000 = 1:1 postscale 0001 = 1:2 postscale 1111 = 1:16 postscale bit 2 tmr2on : timer2 on bit 1 = timer2 is on 0 = timer2 is off bit 1-0 t2ckps1:t2ckps0 : timer2 clock prescale select bits 00 = prescaler is 1 01 = prescaler is 4 1x = prescaler is 16 legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 142 preliminary ? 2004 microchip technology inc. 12.2 timer2 interrupt timer2 also can generate an optional device interrupt. the timer2 output signal (tmr2-to-pr2 match) provides the input for the 4-bit output counter/postscaler. this counter generates the tmr2 match interrupt flag which is latched in tmr2if (pir1<1>). the interrupt is enabled by setting the tmr2 match interrupt enable bit, tmr2ie (pie1<1>). a range of 16 postscale options (from 1:1 through 1:16 inclusive) can be selected with the postscaler control bits, t2outps3:t2outps0 (t2con<6:3>). 12.3 tmr2 output the unscaled output of tmr2 is available primarily to the ccp modules, where it is used as a time base for operations in pwm mode. timer2 can be optionally used as the shift clock source for the mssp module operating in spi mode. additional information is provided in section 15.0 ?master synchronous serial port (mssp) module? . figure 12-1: timer2 block diagram table 12-1: registers associated with timer2 as a timer/counter name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir1 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if 61 pie1 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie 61 ipr1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip 61 tmr2 timer2 module register 60 t2con ? t2outps3 t2outps2 t2outps1 t2outps0 tmr2on t2ckps1 t2ckps0 60 pr2 timer2 period register 60 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used by the timer2 module. comparator tmr2 output tmr2 postscaler prescaler pr2 2 f osc /4 1:1 to 1:16 1:1, 1:4, 1:16 4 t2outps3:t2outps0 t2ckps1:t2ckps0 set tmr2if internal data bus 8 reset tmr2/pr2 8 8 (to pwm or mssp) match
? 2004 microchip technology inc. preliminary ds39629b-page 143 PIC18F6390/6490/8390/8490 13.0 timer3 module the timer3 timer/counter module incorporates these features: software selectable operation as a 16-bit timer or counter readable and writable 8-bit registers (tmr3h and tmr3l) selectable clock source (internal or external), with device clock or timer1 oscillator internal options interrupt-on-overflow module reset on ccp special event trigger a simplified block diagram of the timer3 module is shown in figure 13-1. a block diagram of the module?s operation in read/write mode is shown in figure 13-2. the timer3 module is controlled through the t3con register (register 13-1). it also selects the clock source options for the ccp modules (see section 14.1.1 ?ccp modules and timer resources? for more information). register 13-1: t3con: time r3 control register r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 rd16 t3ccp2 t3ckps1 t3ckps0 t3ccp1 t3sync tmr3cs tmr3on bit 7 bit 0 bit 7 rd16: 16-bit read/write mode enable bit 1 = enables register read/write of timer3 in one 16-bit operation 0 = enables register read/write of timer3 in two 8-bit operations bit 6, 3 t3ccp2:t3ccp1: timer3 and timer1 to ccpx enable bits 1x = timer3 is the capture/compare clock source for the ccp modules 01 = timer3 is the capture/compare clock source for ccp2; timer1 is the capture/compare clock source for ccp1 00 = timer1 is the capture/compare clock source for the ccp modules bit 5-4 t3ckps1:t3ckps0 : timer3 input clock prescale select bits 11 = 1:8 prescale value 10 = 1:4 prescale value 01 = 1:2 prescale value 00 = 1:1 prescale value bit 2 t3sync : timer3 external clock input synchronization control bit (not usable if the device clock comes from timer1/timer3.) when tmr3cs = 1 : 1 = do not synchronize external clock input 0 = synchronize external clock input when tmr3cs = 0 : this bit is ignored. timer3 uses the internal clock when tmr3cs = 0 . bit 1 tmr3cs: timer3 clock source select bit 1 = external clock input from timer1 oscillator or t13cki (on the rising edge after the first falling edge) 0 = internal clock (f osc /4) bit 0 tmr3on: timer3 on bit 1 = enables timer3 0 = stops timer3 legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 144 preliminary ? 2004 microchip technology inc. 13.1 timer3 operation timer3 can operate in one of three modes: timer synchronous counter asynchronous counter the operating mode is determined by the clock select bit, tmr3cs (t3con<1>). when tmr3cs is cleared (= 0 ), timer3 increments on every internal instruction cycle (f osc /4). when the bit is set, timer3 increments on every rising edge of the timer1 external clock input or the timer1 oscillator, if enabled. as with timer1, the rc1/t1osi and rc0/t1oso/t13cki pins become inputs when the timer1 oscillator is enabled. this means the values of trisc<1:0> are ignored and the pins are read as ? 0 ?. figure 13-1: timer3 block diagram figure 13-2: timer3 block diagram (16-bit read/write mode) t3sync tmr3cs t3ckps1:t3ckps0 sleep input t1oscen (1) f osc /4 internal clock prescaler 1, 2, 4, 8 synchronize detect 1 0 2 t1oso/t13cki t1osi 1 0 tmr3on tmr3l set tmr3if on overflow tmr3 high byte timer1 oscillator note 1: when t1oscen is cleared, the inverter and feedback resistor are turned off to eliminate power drain. on/off timer3 ccp special event trigger tccpx clear tmr3 t3sync tmr3cs t3ckps1:t3ckps0 sleep input t1oscen (1) f osc /4 internal clock prescaler 1, 2, 4, 8 synchronize detect 1 0 2 t1oso/t13cki t1osi note 1: when t1oscen is cleared, the inverter and feedback resistor are turned off to eliminate power drain. 1 0 tmr3l internal data bus 8 set tmr3if on overflow tmr3 tmr3h high byte 8 8 8 read tmr3l write tmr3l 8 tmr3on ccp special event trigger timer1 oscillator on/off timer3 timer1 clock input tccpx clear tmr3
? 2004 microchip technology inc. preliminary ds39629b-page 145 PIC18F6390/6490/8390/8490 13.2 timer3 16-bit read/write mode timer3 can be configured for 16-bit reads and writes (see figure 13-2). when the rd16 control bit (t3con<7>) is set, the address for tmr3h is mapped to a buffer register for the high byte of timer3. a read from tmr3l will load the contents of the high byte of timer3 into the timer3 high byte buffer register. this provides the user with the ability to accurately read all 16 bits of timer1 without having to determine whether a read of the high byte, followed by a read of the low byte, has become invalid due to a rollover between reads. a write to the high byte of timer3 must also take place through the tmr3h buffer register. the timer3 high byte is updated with the contents of tmr3h when a write occurs to tmr3l. this allows a user to write all 16 bits to both the high and low bytes of timer3 at once. the high byte of timer3 is not directly readable or writable in this mode. all reads and writes must take place through the timer3 high byte buffer register. writes to tmr3h do not clear the timer3 prescaler. the prescaler is only cleared on writes to tmr3l. 13.3 using the timer1 oscillator as the timer3 clock source the timer1 internal oscillator may be used as the clock source for timer3. the timer1 oscillator is enabled by setting the t1oscen (t1con<3>) bit. to use it as the timer3 clock source, the tmr3cs bit must also be set. as previously noted, this also configures timer3 to increment on every rising edge of the oscillator source. the timer1 oscillator is described in section 11.0 ?timer1 module? . 13.4 timer3 interrupt the tmr3 register pair (tmr3h:tmr3l) increments from 0000h to ffffh and overflows to 0000h. the timer3 interrupt, if enabled, is generated on overflow and is latched in interrupt flag bit, tmr3if (pir2<1>). this interrupt can be enabled or disabled by setting or clearing the timer3 interrupt enable bit, tmr3ie (pie2<1>). 13.5 resetting timer3 using the ccp special event trigger if either of the ccp modules is configured in compare mode to generate a special event trigger (ccp1m3:ccp1m0 or ccp2m3:ccp2m0 = 1011 ), this signal will reset timer1. the trigger from ccp2 will also start an a/d conversion if the a/d module is enabled (see section 14.3.4 ?special event trigger? for more information.). the module must be configured as either a timer or synchronous counter to take advantage of this feature. when used this way, the ccpr2h:ccpr2l register pair effectively becomes a period register for timer3. if timer3 is running in asynchronous counter mode, the reset operation may not work. in the event that a write to timer3 coincides with a special event trigger from a ccp module, the write will take precedence. table 13-1: registers associated with timer3 as a timer/counter note: the special event triggers from the ccp2 module will not set the tmr3if interrupt flag bit (pir2<1>). name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir2 oscfif cmif ? ? bclif hlvdif tmr3if ccp2if 61 pie2 oscfie cmie ? ? bclie hlvdie tmr3ie ccp2ie 61 ipr2 oscfip cmip ? ? bclip hlvdip tmr3ip ccp2ip 61 tmr3l holding register for the least significant byte of the 16-bit tmr3 register 61 tmr3h holding register for the most significant byte of the 16-bit tmr3 register 61 t1con rd16 t1run t1ckps1 t1ckps0 t1oscen t1sync tmr1cs tmr1on 60 t3con rd16 t3ccp2 t3ckps1 t3ckps0 t3ccp1 t3sync tmr3cs tmr3on 61 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used by the timer3 module.
PIC18F6390/6490/8390/8490 ds39629b-page 146 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 147 PIC18F6390/6490/8390/8490 14.0 capture/compare/pwm (ccp) modules PIC18F6390/6490/8390/8490 devices have two ccp (capture/compare/pwm) modules, designated ccp1 and ccp2. both modules implement standard capture, compare and pulse width modulation (pwm) modes. each ccp module contains a 16-bit register which can operate as a 16-bit capture register, a 16-bit compare register or a pwm master/slave duty cycle register. for the sake of clarity, all ccp module operation in the following sections is described with respect to ccp2, but is equally applicable to ccp1. register 14-1: ccpxcon register (ccp1 module, ccp2 module) u-0 u-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 ? ? dcxb1 dcxb0 ccpxm3 ccpxm2 ccpxm1 ccpxm0 bit 7 bit 0 bit 7-6 unimplemented: read as ? 0 ? bit 5-4 dcxb1:dcxb0 : pwm duty cycle bit 1 and bit 0 for ccp module x capture mode: unused. compare mode : unused. pwm mode: these bits are the two least significant bits (bit 1 and bit 0) of the 10-bit pwm duty cycle. the eight most significant bits (dcx9:dcx2) of the duty cycle are found in ccprxl. bit 3-0 ccpxm3:ccpxm0 : ccp module x mode select bits 0000 = capture/compare/pwm disabled (resets ccpx module) 0001 = reserved 0010 = compare mode, toggle output on match (ccpxif bit is set) 0011 = reserved 0100 = capture mode, every falling edge 0101 = capture mode, every rising edge 0110 = capture mode, every 4th rising edge 0111 = capture mode, every 16th rising edge 1000 = compare mode: initialize ccp pin low; on compare match, force ccp pin high (ccpif bit is set) 1001 = compare mode: initialize ccp pin high; on compare match, force ccp pin low (ccpif bit is set) 1010 = compare mode: generate software interrupt on compare match (ccpif bit is set, ccp pin reflects i/o state) 1011 = compare mode: trigger special event, reset timer, start a/d conversion on ccp2 match (ccpif bit is set) (1) 11xx = pwm mode note 1: ccp1m3:ccp1m0 = 1011 will only reset timer and not start a/d conversion on ccp1 match. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 148 preliminary ? 2004 microchip technology inc. 14.1 ccp module configuration each capture/compare/pwm module is associated with a control register (generically, ccpxcon) and a data register (ccprx). the data register in turn is com- prised of two 8-bit registers: ccprxl (low byte) and ccprxh (high byte). all registers are both readable and writable. 14.1.1 ccp modules and timer resources the ccp modules utilize timers 1, 2 or 3, depending on the mode selected. timer1 and timer3 are available to modules in capture or compare modes, while timer2 is available for modules in pwm mode. table 14-1: ccp mode ? timer resource the assignment of a particular timer to a module is determined by the timer-to-ccp enable bits in the t3con register (register 13-1). both modules may be active at any given time and may share the same timer resource if they are configured to operate in the same mode (capture/compare or pwm) at the same time. the interactions between the two modules are summarized in table 14-2. depending on the configuration selected, up to four timers may be active at once, with modules in the same configuration (capture/compare or pwm) sharing timer resources. the possible configurations are shown in figure 14-1. 14.1.2 ccp2 pin assignment the pin assignment for ccp2 (capture input, compare and pwm output) can change, based on device config- uration. the ccp2mx configuration bit determines which pin ccp2 is multiplexed to. by default, it is assigned to rc1 (ccp2mx = 1 ). if the configuration bit is cleared, ccp2 is multiplexed with re7. changing the pin assignment of ccp2 does not automatically change any requirements for configuring the port pin. users must always verify that the appropri- ate tris register is configured correctly for ccp2 operation, regardless of where it is located. figure 14-1: ccp and timer interconnect configurations ccp mode timer resource capture compare pwm timer1 or timer3 timer1 or timer3 timer2 tmr1 tmr2 tmr3 ccp2 ccp1 tmr1 tmr2 tmr3 ccp2 ccp1 tmr1 tmr3 tmr2 ccp2 ccp1 t3ccp<2:1> = 00 t3ccp<2:1> = 01 t3ccp<2:1> = 1x timer1 is used for all capture and compare operations for all ccp modules. timer2 is used for pwm operations for all ccp modules. modules may share either timer resource as a common time base. timer1 is used for capture and compare operations for ccp1 and timer 3 is used for ccp2. both the modules use timer2 as a common time base if they are in pwm modes. timer3 is used for all capture and compare operations for all ccp modules. timer2 is used for pwm operations for all ccp modules. modules may share either timer resource as a common time base.
? 2004 microchip technology inc. preliminary ds39629b-page 149 PIC18F6390/6490/8390/8490 table 14-2: interactions between ccp1 and ccp2 for timer resources ccp1 mode ccp2 mode interaction capture capture each module can use tmr1 or tmr3 as the time base. the time base can be different for each ccp. capture compare ccp2 can be configured for the special event trigger to reset tmr1 or tmr3 (depending upon which time base is used). automatic a/d conversions on trigger event can also be done. operation of ccp1 could be affected if it is using the same timer as a time base. compare capture ccp1 can be configured for the special event trigger to reset tmr1 or tmr3 (depending upon which time base is used). operation of ccp2 could be affected if it is using the same timer as a time base. compare compare either module can be configured for the special event trigger to reset the time base. automatic a/d conversions on ccp2 trigger event can be done. conflicts may occur if both modules are using the same time base. capture pwm* none compare pwm* none pwm* capture none pwm* compare none pwm* pwm both pwms will have the same frequency and update rate (tmr2 interrupt). * includes standard and enhanced pwm operation.
PIC18F6390/6490/8390/8490 ds39629b-page 150 preliminary ? 2004 microchip technology inc. 14.2 capture mode in capture mode, the ccpr2h:ccpr2l register pair captures the 16-bit value of the tmr1 or tmr3 registers when an event occurs on the ccp2 pin (rc1 or re7, depending on device configuration). an event is defined as one of the following: every falling edge every rising edge every 4th rising edge every 16th rising edge the event is selected by the mode select bits, ccp2m3:ccp2m0 (ccp2con<3:0>). when a capture is made, the interrupt request flag bit, ccp2if (pir2<1>), is set; it must be cleared in software. if another capture occurs before the value in register ccpr2 is read, the old captured value is overwritten by the new captured value. 14.2.1 ccp pin configuration in capture mode, the appropriate ccpx pin should be configured as an input by setting the corresponding tris direction bit. 14.2.2 timer1/timer3 mode selection the timers that are to be used with the capture feature (timer1 and/or timer3) must be running in timer mode or synchronized counter mode. in asynchronous counter mode, the capture operation may not work. the timer to be used with each ccp module is selected in the t3con register (see section 14.1.1 ?ccp modules and timer resources? ). 14.2.3 software interrupt when the capture mode is changed, a false capture interrupt may be generated. the user should keep bit ccp2ie (pie2<1>) clear to avoid false interrupts and should clear the flag bit, ccp2if, following any such change in operating mode. 14.2.4 ccp prescaler there are four prescaler settings in capture mode; they are specified as part of the operating mode selected by the mode select bits (ccp2m3:ccp2m0). whenever the ccp module is turned off, or the ccp module is not in capture mode, the prescaler counter is cleared. this means that any reset will clear the prescaler counter. switching from one capture prescaler to another may generate an interrupt. also, the prescaler counter will not be cleared; therefore, the first capture may be from a non-zero prescaler. example 14-1 shows the recommended method for switching between capture prescalers. this example also clears the prescaler counter and will not generate the ?false? interrupt. example 14-1: changing between capture prescalers figure 14-2: capture mode operat ion block diagram note: if rc1/ccp2 or re7/ccp2 is configured as an output, a write to the port can cause a capture condition. clrf ccp2con ; turn ccp module off movlw new_capt_ps ; load wreg with the ; new prescaler mode ; value and ccp on movwf ccp2con ; load ccp2con with ; this value ccpr1h ccpr1l tmr1h tmr1l set ccp1if tmr3 enable q1:q4 ccp1con<3:0> ccp1 pin prescaler 1, 4, 16 and edge detect tmr1 enable t3ccp2 t3ccp2 ccpr2h ccpr2l tmr1h tmr1l set ccp2if tmr3 enable ccp2con<3:0> ccp2 pin prescaler 1, 4, 16 tmr3h tmr3l tmr1 enable t3ccp2 t3ccp1 t3ccp2 t3ccp1 tmr3h tmr3l and edge detect 4 4 4
? 2004 microchip technology inc. preliminary ds39629b-page 151 PIC18F6390/6490/8390/8490 14.3 compare mode in compare mode, the 16-bit ccpr2 register value is constantly compared against either the tmr1 or tmr3 register pair value. when a match occurs, the ccp2 pin can be: driven high driven low toggled (high-to-low or low-to-high) remain unchanged (that is, reflects the state of the i/o latch) the action on the pin is based on the value of the mode select bits (ccp2m3:ccp2m0). at the same time, the interrupt flag bit, ccp2if, is set. 14.3.1 ccp pin configuration the user must configure the ccpx pin as an output by clearing the appropriate tris bit. 14.3.2 timer1/timer3 mode selection timer1 and/or timer3 must be running in timer mode, or synchronized counter mode, if the ccp module is using the compare feature. in asynchronous counter mode, the compare operation may not work. 14.3.3 software interrupt mode when the generate software interrupt mode is chosen (ccp2m3:ccp2m0 = 1010 ), the ccp2 pin is not affected. only a ccp interrupt is generated if enabled and the ccp2ie bit is set. 14.3.4 special event trigger both ccp modules are equipped with a special event trigger. this is an internal hardware signal generated in compare mode to trigger actions by other modules. the special event trigger is enabled by selecting the compare special event trigger mode (ccp2m3:ccp2m0 = 1011 ). for either ccp module, the special event trigger resets the timer register pair for whichever timer resource is currently assigned as the module?s time base. this allows the ccprx registers to serve as a programmable period register for either timer. the special event trigger for ccp2 can also start an a/d conversion. in order to do this, the a/d converter must already be enabled. figure 14-3: compare mode operat ion block diagram note: clearing the ccp2con register will force the rc1 or re7 compare output latch (depending on device configuration) to the default low level. this is not the portc or porte i/o data latch. note: the special event trigger of ccp1 only resets timer1/timer3 and cannot start an a/d conversion even when the a/d converter is enabled. ccpr1h ccpr1l tmr1h tmr1l comparator q s r output logic special event trigger set ccp1if ccp1 pin tris ccp1con<3:0> output enable tmr3h tmr3l ccpr2h ccpr2l comparator 1 0 t3ccp2 t3ccp1 set ccp2if 1 0 compare 4 (timer1 reset) q s r output logic special event trigger ccp2 pin tris ccp2con<3:0> output enable 4 (timer1/timer3 reset, a/d trigger) match compare match
PIC18F6390/6490/8390/8490 ds39629b-page 152 preliminary ? 2004 microchip technology inc. table 14-3: registers associated with capture, compare, timer1 and timer3 name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 rcon ipen sboren ? ri to pd por bor 60 pir1 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if 61 pie1 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie 61 ipr1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip 61 pir2 oscfif cmif ? ? bclif hlvdif tmr3if ccp2if 61 pie2 oscfie cmie ? ? bclie hlvdie tmr3ie ccp2ie 61 ipr2 oscfip cmip ? ? bclip hlvdip tmr3ip ccp2ip 61 trisc portc data direction register 62 trise porte data direction register ? ? ? ?62 tmr1l holding register for the least significant byte of the 16-bit tmr1 register 60 tmr1h holding register for the most significant byte of the 16-bit tmr1 register 60 t1con rd16 t1run t1ckps1 t1ckps0 t1oscen t1sync tmr1cs tmr1on 60 tmr3h timer3 register high byte 61 tmr3l timer3 register low byte 61 t3con rd16 t3ccp2 t3ckps1 t3ckps0 t3ccp1 t3sync tmr3cs tmr3on 61 ccpr1l capture/compare/pwm register 1 (lsb) 61 ccpr1h capture/compare/pwm register 1 (msb) 61 ccp1con ? ? dc1b1 dc1b0 ccp1m3 ccp1m2 ccp1m1 ccp1m0 61 ccpr2l capture/compare/pwm register 2 (lsb) 61 ccpr2h capture/compare/pwm register 2 (msb) 61 ccp2con ? ? dc2b1 dc2b0 ccp2m3 ccp2m2 ccp2m1 ccp2m0 61 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used by capture/compare, timer1 or timer3. note 1: these bits are unimplemented on 64-pin devices; always maintain these bits clear.
? 2004 microchip technology inc. preliminary ds39629b-page 153 PIC18F6390/6490/8390/8490 14.4 pwm mode in pulse width modulation (pwm) mode, the ccp2 pin produces up to a 10-bit resolution pwm output. since the ccp2 pin is multiplexed with a portc or porte data latch, the appropriate tris bit must be cleared to make the ccp2 pin an output. figure 14-4 shows a simplified block diagram of the ccp module in pwm mode. for a step-by-step procedure on how to set up the ccp module for pwm operation, see section 14.4.3 ?setup for pwm operation? . figure 14-4: simplified pwm block diagram a pwm output (figure 14-5) has a time base (period) and a time that the output stays high (duty cycle). the frequency of the pwm is the inverse of the period (1/period). figure 14-5: pwm output 14.4.1 pwm period the pwm period is specified by writing to the pr2 register. the pwm period can be calculated using the following formula: equation 14-1: pwm frequency is defined as 1/[pwm period]. when tmr2 is equal to pr2, the following three events occur on the next increment cycle: tmr2 is cleared the ccp2 pin is set (exception: if pwm duty cycle = 0%, the ccp2 pin will not be set) the pwm duty cycle is latched from ccpr2l into ccpr2h note: clearing the ccp2con register will force the rc1 or re7 output latch (depending on device configuration) to the default low level. this is not the portc or porte i/o data latch. ccpr1l ccpr1h (slave) comparator tmr2 comparator pr2 (note 1) r q s duty cycle registers ccp1con<5:4> clear timer, ccp1 pin and latch d.c. trisc<2> rc2/ccp1 note 1: the 8-bit tmr2 value is concatenated with the 2-bit internal q clock, or 2 bits of the prescaler, to create the 10-bit time base. note: the timer2 postscalers (see section 12.0 ?timer2 module? ) are not used in the determination of the pwm frequency. the postscaler could be used to have a servo update rate at a different frequency than the pwm output. period duty cycle tmr2 = pr2 tmr2 = duty cycle tmr2 = pr2 pwm period = (pr2) + 1] ? 4 t osc (tmr2 prescale value)
PIC18F6390/6490/8390/8490 ds39629b-page 154 preliminary ? 2004 microchip technology inc. 14.4.2 pwm duty cycle the pwm duty cycle is specified by writing to the ccpr2l register and to the ccp2con<5:4> bits. up to 10-bit resolution is available. the ccpr2l contains the eight msbs and the ccp2con<5:4> contains the two lsbs. this 10-bit value is represented by ccpr2l:ccp2con<5:4>. the following equation is used to calculate the pwm duty cycle in time: equation 14-2: ccpr2l and ccp2con<5:4> can be written to at any time, but the duty cycle value is not latched into ccpr2h until after a match between pr2 and tmr2 occurs (i.e., the period is complete). in pwm mode, ccpr2h is a read-only register. the ccpr2h register and a 2-bit internal latch are used to double-buffer the pwm duty cycle. this double-buffering is essential for glitchless pwm operation. when the ccpr2h and 2-bit latch match tmr2, concatenated with an internal 2-bit q clock or 2 bits of the tmr2 prescaler, the ccp2 pin is cleared. the maximum pwm resolution (bits) for a given pwm frequency is given by the equation: equation 14-3: table 14-4: example pwm frequencies and resolutions at 40 mhz pwm duty cycle = (ccpr2l:ccp2con<5:4>) t osc (tmr2 prescale value) note: if the pwm duty cycle value is longer than the pwm period, the ccp2 pin will not be cleared. f osc f pwm --------------- ?? ?? log 2 () log ----------------------------- b i t s = pwm resolution (max) pwm frequency 2.44 khz 9.77 khz 39.06 khz 156.25 khz 312.50 khz 416.67 khz timer prescaler (1, 4, 16)1641111 pr2 value ffh ffh ffh 3fh 1fh 17h maximum resolution (bits) 14 12 10 8 7 6.58
? 2004 microchip technology inc. preliminary ds39629b-page 155 PIC18F6390/6490/8390/8490 14.4.3 setup for pwm operation the following steps should be taken when configuring the ccp module for pwm operation: 1. set the pwm period by writing to the pr2 register. 2. set the pwm duty cycle by writing to the ccpr2l register and ccp2con<5:4> bits. 3. make the ccp2 pin an output by clearing the appropriate tris bit. 4. set the tmr2 prescale value, then enable timer2 by writing to t2con. 5. configure the ccp2 module for pwm operation. table 14-5: registers associated with pwm and timer2 name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 rcon ipen sboren ? ri to pd por bor 60 pir1 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if 61 pie1 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie 61 ipr1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip 61 trisc portc data direction register 62 trise porte data direction register ? ? ? ?62 tmr2 timer2 module register 60 pr2 timer2 module period register 60 t2con ? t2outps3 t2outps2 t2outps1 t2o utps0 tmr2on t2ckps1 t2ckps0 60 ccpr1l capture/compare/pwm register 1 (lsb) 61 ccpr1h capture/compare/pwm register 1 (msb) 61 ccp1con ? ? dc1b1 dc1b0 ccp1m3 ccp1m2 ccp1m1 ccp1m0 61 ccpr2l capture/compare/pwm register 2 (lsb) 61 ccpr2h capture/compare/pwm register 2 (msb) 61 ccp2con ? ? dc2b1 dc2b0 ccp2m3 ccp2m2 ccp2m1 ccp2m0 61 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used by pwm or timer2.
PIC18F6390/6490/8390/8490 ds39629b-page 156 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 157 PIC18F6390/6490/8390/8490 15.0 master synchronous serial port (mssp) module 15.1 master ssp (mssp) module overview the master synchronous serial port (mssp) module is a serial interface, useful for communicating with other peripheral or microcontroller devices. these peripheral devices may be serial eeproms, shift registers, display drivers, a/d converters, etc. the mssp module can operate in one of two modes: serial peripheral interface (spi) inter-integrated circuit (i 2 c) - full master mode - slave mode (with general address call) the i 2 c interface supports the following modes in hardware: master mode multi-master mode slave mode 15.2 control registers the mssp module has three associated registers. these include a status register (sspstat) and two control registers (sspcon1 and sspcon2). the use of these registers and their individual configuration bits differ significantly depending on whether the mssp module is operated in spi or i 2 c mode. additional details are provided under the individual sections. 15.3 spi mode the spi mode allows 8 bits of data to be synchronously transmitted and received simultaneously. all four modes of spi are supported. to accomplish communication, typically three pins are used: serial data out (sdo) ? rc5/sdo/seg12 serial data in (sdi) ? rc4/sdi/sda serial clock (sck) ? rc3/sck/scl additionally, a fourth pin may be used when in a slave mode of operation: slave select (ss ) ? rf7/ss figure 15-1 shows the block diagram of the mssp module when operating in spi mode. figure 15-1: mssp block diagram (spi? mode) ( ) read write internal data bus sspsr reg sspm3:sspm0 bit 0 shift clock ss control enable edge select clock select tmr2 output t osc prescaler 4, 16, 64 2 edge select 2 4 data to tx/rx in sspsr tris bit 2 smp:cke rc5/sdo/seg12 sspbuf reg rc4/sdi/sda rf7/ss rc3/sck/ scl
PIC18F6390/6490/8390/8490 ds39629b-page 158 preliminary ? 2004 microchip technology inc. 15.3.1 registers the mssp module has four registers for spi mode operation. these are: mssp control register 1 (sspcon1) mssp status register (sspstat) serial receive/transmit buffer register (sspbuf) mssp shift register (sspsr) ? not directly accessible sspcon1 and sspstat are the control and status registers in spi mode operation. the sspcon1 register is readable and writable. the lower 6 bits of the sspstat are read-only. the upper 2 bits of the sspstat are read/write. sspsr is the shift register used for shifting data in or out. sspbuf is the buffer register to which data bytes are written to or read from. in receive operations, sspsr and sspbuf together create a double-buffered receiver. when sspsr receives a complete byte, it is transferred to sspbuf and the sspif interrupt is set. during transmission, the sspbuf is not double- buffered. a write to sspbuf will write to both sspbuf and sspsr. register 15-1: sspstat: mssp status register (spi mode) r/w-0 r/w-0 r-0 r-0 r-0 r-0 r-0 r-0 smp cke d/a psr/w ua bf bit 7 bit 0 bit 7 smp: sample bit spi master mode: 1 = input data sampled at end of data output time 0 = input data sampled at middle of data output time spi slave mode: smp must be cleared when spi is used in slave mode. bit 6 cke: spi clock edge select bit when ckp = 0 : 1 = data transmitted on rising edge of sck 0 = data transmitted on falling edge of sck when ckp = 1 : 1 = data transmitted on falling edge of sck 0 = data transmitted on rising edge of sck bit 5 d/a : data/address bit used in i 2 c mode only. bit 4 p: stop bit used in i 2 c mode only. this bit is cleared when the mssp module is disabled, sspen is cleared. bit 3 s: start bit used in i 2 c mode only. bit 2 r/w : read/write bit information used in i 2 c mode only. bit 1 ua: update address bit used in i 2 c mode only. bit 0 bf: buffer full status bit (receive mode only) 1 = receive complete, sspbuf is full 0 = receive not complete, sspbuf is empty legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
? 2004 microchip technology inc. preliminary ds39629b-page 159 PIC18F6390/6490/8390/8490 register 15-2: sspcon1: mssp control register 1 (spi mode) r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 wcol sspov sspen ckp sspm3 sspm2 sspm1 sspm0 bit 7 bit 0 bit 7 wcol: write collision detect bit (transmit mode only) 1 = the sspbuf register is written while it is still transmitting the previous word (must be cleared in software) 0 = no collision bit 6 sspov: receive overflow indicator bit spi slave mode: 1 = a new byte is received while the sspbuf register is still holding the previous data. in case of overflow, the data in sspsr is lost. overflow can only occur in slave mode. the user must read the sspbuf, even if only transmitting data, to avoid setting overflow (must be cleared in software). 0 = no overflow note: in master mode, the overflow bit is not set since each new reception (and transmission) is initiated by writing to the sspbuf register. bit 5 sspen: synchronous serial port enable bit 1 = enables serial port and configures sck, sdo, sdi and ss as serial port pins 0 = disables serial port and configures these pins as i/o port pins note: when enabled, these pins must be properly configured as input or output. bit 4 ckp: clock polarity select bit 1 = idle state for clock is a high level 0 = idle state for clock is a low level bit 3-0 sspm3:sspm0: synchronous serial port mode select bits 0101 = spi slave mode, clock = sck pin, ss pin control disabled, ss can be used as i/o pin 0100 = spi slave mode, clock = sck pin, ss pin control enabled 0011 = spi master mode, clock = tmr2 output/2 0010 = spi master mode, clock = f osc /64 0001 = spi master mode, clock = f osc /16 0000 = spi master mode, clock = f osc /4 note: bit combinations not specifically listed here are either reserved or implemented in i 2 c mode only. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 160 preliminary ? 2004 microchip technology inc. 15.3.2 operation when initializing the spi, several options need to be specified. this is done by programming the appropriate control bits (sspcon1<5:0> and sspstat<7:6>). these control bits allow the following to be specified: master mode (sck is the clock output) slave mode (sck is the clock input) clock polarity (idle state of sck) data input sample phase (middle or end of data output time) clock edge (output data on rising/falling edge of sck) clock rate (master mode only) slave select mode (slave mode only) the mssp consists of a transmit/receive shift register (sspsr) and a buffer register (sspbuf). the sspsr shifts the data in and out of the device, msb first. the sspbuf holds the data that was written to the sspsr until the received data is ready. once the 8 bits of data have been received, that byte is moved to the sspbuf register. then, the buffer full detect bit, bf (sspstat<0>) and the interrupt flag bit, sspif, are set. this double-buffering of the received data (sspbuf) allows the next byte to start reception before reading the data that was just received. any write to the sspbuf register during transmission/reception of data will be ignored and the write collision detect bit, wcol (sspcon1<7>), will be set. user software must clear the wcol bit so that it can be determined if the follow- ing write(s) to the sspbuf register completed successfully. when the application software is expecting to receive valid data, the sspbuf should be read before the next byte of data to transfer is written to the sspbuf. the buffer full bit, bf (sspstat<0>), indicates when sspbuf has been loaded with the received data (transmission is complete). when the sspbuf is read, the bf bit is cleared. this data may be irrelevant if the spi is only a transmitter. generally, the mssp interrupt is used to determine when the transmission/reception has completed. the sspbuf must be read and/or written. if the interrupt method is not going to be used, then software polling can be done to ensure that a write collision does not occur. example 15-1 shows the loading of the sspbuf (sspsr) for data transmission. the sspsr is not directly readable or writable and can only be accessed by addressing the sspbuf register. additionally, the mssp status register (sspstat) indicates the various status conditions. example 15-1: loading the sspbuf (sspsr) register loop btfss sspstat, bf ;has data been received (transmit complete)? bra loop ;no movf sspbuf, w ;wreg reg = contents of sspbuf movwf rxdata ;save in user ram, if data is meaningful movf txdata, w ;w reg = contents of txdata movwf sspbuf ;new data to xmit
? 2004 microchip technology inc. preliminary ds39629b-page 161 PIC18F6390/6490/8390/8490 15.3.3 enabling spi i/o to enable the serial port, ssp enable bit, sspen (sspcon1<5>), must be set. to reset or reconfigure spi mode, clear the sspen bit, reinitialize the sspcon registers and then set the sspen bit. this configures the sdi, sdo, sck and ss pins as serial port pins. for the pins to behave as the serial port func- tion, some must have their data direction bits (in the tris register) appropriately programmed as follows: sdi is automatically controlled by the spi module sdo must have trisc<5> bit cleared sck (master mode) must have trisc<3> bit cleared sck (slave mode) must have trisc<3> bit set ss must have trisf<7> bit set any serial port function that is not desired may be overridden by programming the corresponding data direction (tris) register to the opposite value. 15.3.4 typical connection figure 15-2 shows a typical connection between two microcontrollers. the master controller (processor 1) initiates the data transfer by sending the sck signal. data is shifted out of both shift registers on their programmed clock edge and latched on the opposite edge of the clock. both processors should be programmed to the same clock polarity (ckp), then both controllers would send and receive data at the same time. whether the data is meaningful (or dummy data) depends on the application software. this leads to three scenarios for data transmission: master sends data ? slave sends dummy data master sends data ? slave sends data master sends dummy data ? slave sends data figure 15-2: spi? master/slave connection serial input buffer (sspbuf) shift register (sspsr) msb lsb sdo sdi processor 1 sck spi? master sspm3:sspm0 = 00xx serial input buffer (sspbuf) shift register (sspsr) lsb msb sdi sdo processor 2 sck spi? slave sspm3:sspm0 = 010x serial clock
PIC18F6390/6490/8390/8490 ds39629b-page 162 preliminary ? 2004 microchip technology inc. 15.3.5 master mode the master can initiate the data transfer at any time because it controls the sck. the master determines when the slave (processor 2, figure 15-2) is to broadcast data by the software protocol. in master mode, the data is transmitted/received as soon as the sspbuf register is written to. if the spi is only going to receive, the sdo output could be disabled (programmed as an input). the sspsr regis- ter will continue to shift in the signal present on the sdi pin at the programmed clock rate. as each byte is received, it will be loaded into the sspbuf register as if a normal received byte (interrupts and status bits appropriately set). this could be useful in receiver applications as a ?line activity monitor? mode. the clock polarity is selected by appropriately programming the ckp bit (sspcon1<4>). this then, would give waveforms for spi communication as shown in figure 15-3, figure 15-5 and figure 15-6, where the msb is transmitted first. in master mode, the spi clock rate (bit rate) is user programmable to be one of the following: f osc /4 (or t cy ) f osc /16 (or 4 t cy ) f osc /64 (or 16 t cy ) timer2 output/2 this allows a maximum data rate (at 40 mhz) of 10.00 mbps. figure 15-3 shows the waveforms for master mode. when the cke bit is set, the sdo data is valid before there is a clock edge on sck. the change of the input sample is shown based on the state of the smp bit. the time when the sspbuf is loaded with the received data is shown. figure 15-3: spi? mode waveform (master mode) sck (ckp = 0 sck (ckp = 1 sck (ckp = 0 sck (ckp = 1 4 clock modes input sample input sample sdi bit 7 bit 0 sdo bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 bit 7 sdi sspif (smp = 1 ) (smp = 0 ) (smp = 1 ) cke = 1 ) cke = 0 ) cke = 1 ) cke = 0 ) (smp = 0 ) write to sspbuf sspsr to sspbuf sdo bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 (cke = 0 ) (cke = 1 ) next q4 cycle after q2 bit 0
? 2004 microchip technology inc. preliminary ds39629b-page 163 PIC18F6390/6490/8390/8490 15.3.6 slave mode in slave mode, the data is transmitted and received as the external clock pulses appear on sck. when the last bit is latched, the sspif interrupt flag bit is set. while in slave mode, the external clock is supplied by the external clock source on the sck pin. this external clock must meet the minimum high and low times as specified in the electrical specifications. while in sleep mode, the slave can transmit/receive data. when a byte is received, the device will wake-up from sleep. 15.3.7 slave select synchronization the ss pin allows a synchronous slave mode. the spi must be in slave mode with ss pin control enabled (sspcon1<3:0> = 04h). the pin must not be driven low for the ss pin to function as an input. the data latch must be high. when the ss pin is low, transmission and reception are enabled and the sdo pin is driven. when the ss pin goes high, the sdo pin is no longer driven, even if in the middle of a transmitted byte and becomes a floating output. external pull-up/pull-down resistors may be desirable depending on the application. when the spi module resets, the bit counter is forced to ? 0 ?. this can be done by either forcing the ss pin to a high level or clearing the sspen bit. to emulate two-wire communication, the sdo pin can be connected to the sdi pin. when the spi needs to operate as a receiver, the sdo pin can be configured as an input. this disables transmissions from the sdo. the sdi can always be left as an input (sdi function) since it cannot create a bus conflict. figure 15-4: slave synchronization waveform note 1: when the spi is in slave mode with ss pin control enabled (sspcon<3:0> = 0100 ), the spi module will reset if the ss pin is set to v dd . 2: if the spi is used in slave mode with cke set, then the ss pin control must be enabled. sck (ckp = 1 sck (ckp = 0 input sample sdi bit 7 sdo bit 7 bit 6 bit 7 sspif interrupt (smp = 0 ) cke = 0 ) cke = 0 ) (smp = 0 ) write to sspbuf sspsr to sspbuf ss flag bit 0 bit 7 bit 0 next q4 cycle after q2
PIC18F6390/6490/8390/8490 ds39629b-page 164 preliminary ? 2004 microchip technology inc. figure 15-5: spi? mode waveform (slave mode with cke = 0 ) figure 15-6: spi? mode waveform (slave mode with cke = 1 ) sck (ckp = 1 sck (ckp = 0 input sample sdi bit 7 sdo bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 sspif interrupt (smp = 0 ) cke = 0 ) cke = 0 ) (smp = 0 ) write to sspbuf sspsr to sspbuf ss flag optional next q4 cycle after q2 bit 0 sck (ckp = 1 sck (ckp = 0 input sample sdi bit 7 bit 0 sdo bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 sspif interrupt (smp = 0 ) cke = 1 ) cke = 1 ) (smp = 0 ) write to sspbuf sspsr to sspbuf ss flag not optional next q4 cycle after q2
? 2004 microchip technology inc. preliminary ds39629b-page 165 PIC18F6390/6490/8390/8490 15.3.8 sleep operation in spi master mode, module clocks may be operating at a different speed than when in full power mode; in the case of the sleep mode, all clocks are halted. in most power managed modes, a clock is provided to the peripherals. that clock should be from the primary clock source, the secondary clock (timer1 oscillator at 32.768 khz) or the intosc source. see section 2.7 ?clock sources and oscillator switching? for additional information. in most cases, the speed that the master clocks spi data is not important; however, this should be evaluated for each system. if mssp interrupts are enabled, they can wake the con- troller from sleep mode, or one of the idle modes, when the master completes sending data. if an exit from sleep or idle mode is not desired, mssp interrupts should be disabled. if the sleep mode is selected, all module clocks are halted and the transmission/reception will remain in that state until the devices wakes. after the device returns to run mode, the module will resume transmitting and receiving data. in spi slave mode, the spi transmit/receive shift register operates asynchronously to the device. this allows the device to be placed in any power managed mode and data to be shifted into the spi transmit/ receive shift register. when all 8 bits have been received, the mssp interrupt flag bit will be set and if enabled, will wake the device. 15.3.9 effects of a reset a reset disables the mssp module and terminates the current transfer. 15.3.10 bus mode compatibility table 15-1 shows the compatibility between the standard spi modes and the states of the ckp and cke control bits. table 15-1: spi? bus modes there is also an smp bit which controls when the data is sampled. table 15-2: registers associated with spi? operation standard spi? mode terminology control bits state ckp cke 0, 0 0 1 0, 1 0 0 1, 0 1 1 1, 1 1 0 name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir1 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if 61 pie1 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie 61 ipr1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip 61 trisc portc data direction register 62 trisf portf data direction register 62 sspbuf synchronous serial port receive buffer/transmit register 60 sspcon1 wcol sspov sspen ckp sspm3 sspm2 sspm1 sspm0 60 sspstat smp cke d/a p s r/w ua bf 60 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used by the mssp in spi mode.
PIC18F6390/6490/8390/8490 ds39629b-page 166 preliminary ? 2004 microchip technology inc. 15.4 i 2 c mode the mssp module in i 2 c mode fully implements all master and slave functions (including general call support) and provides interrupts on start and stop bits in hardware to determine a free bus (multi-master function). the mssp module implements the standard mode specifications, as well as 7-bit and 10-bit addressing. two pins are used for data transfer: serial clock (scl) ? rc3/sck/scl serial data (sda) ? rc4/sdi/sda the user must configure these pins as inputs by setting the trisc<4:3> bits. figure 15-7: mssp block diagram (i 2 c? mode) 15.4.1 registers the mssp module has six registers for i 2 c operation. these are: mssp control register 1 (sspcon1) mssp control register 2 (sspcon2) mssp status register (sspstat) serial receive/transmit buffer register (sspbuf) mssp shift register (sspsr) ? not directly accessible mssp address register (sspadd) sspcon1, sspcon2 and sspstat are the control and status registers in i 2 c mode operation. the sspcon1 and sspcon2 registers are readable and writable. the lower 6 bits of the sspstat are read-only. the upper 2 bits of the sspstat are read/write. sspsr is the shift register used for shifting data in or out. sspbuf is the buffer register to which data bytes are written to, or read from. sspadd register holds the slave device address when the ssp is configured in i 2 c slave mode. when the ssp is configured in master mode, the lower 7 bits of sspadd act as the baud rate generator reload value. in receive operations, sspsr and sspbuf together create a double-buffered receiver. when sspsr receives a complete byte, it is transferred to sspbuf and the sspif interrupt is set. during transmission, the sspbuf is not double- buffered. a write to sspbuf will write to both sspbuf and sspsr. read write sspsr reg match detect sspadd reg start and stop bit detect sspbuf reg internal data bus addr match set, reset s, p bits (sspstat reg) rc3/sck/scl rc4/ shift clock msb sdi/ lsb sda
? 2004 microchip technology inc. preliminary ds39629b-page 167 PIC18F6390/6490/8390/8490 register 15-3: sspstat: mssp status register (i 2 c? mode) r/w-0 r/w-0 r-0 r-0 r-0 r-0 r-0 r-0 smp cke d/a p (1) s (1) r/w (2,3) ua bf bit 7 bit 0 bit 7 smp: slew rate control bit in master or slave mode: 1 = slew rate control disabled for standard speed mode (100 khz and 1 mhz) 0 = slew rate control enabled for high-speed mode (400 khz) bit 6 cke: smbus select bit in master or slave mode: 1 = enable smbus specific inputs 0 = disable smbus specific inputs bit 5 d/a : data/address bit in master mode: reserved. in slave mode: 1 = indicates that the last byte received or transmitted was data 0 = indicates that the last byte received or transmitted was address bit 4 p: stop bit (1) 1 = indicates that a stop bit has been detected last 0 = stop bit was not detected last bit 3 s: start bit (1) 1 = indicates that a start bit has been detected last 0 = start bit was not detected last bit 2 r/w : read/write bit information (i 2 c mode only) in slave mode : (2) 1 = read 0 = write in master mode : (3) 1 = transmit is in progress 0 = transmit is not in progress bit 1 ua: update address bit (10-bit slave mode only) 1 = indicates that the user needs to update the address in the sspadd register 0 = address does not need to be updated bit 0 bf: buffer full status bit in transmit mode: 1 = receive complete, sspbuf is full 0 = receive not complete, sspbuf is empty in receive mode: 1 = data transmit in progress (does not include the ack and stop bits), sspbuf is full 0 = data transmit complete (does not include the ack and stop bits), sspbuf is empty note 1: this bit is cleared on reset and when sspen is cleared. 2: this bit holds the r/w bit information following the last address match. this bit is only valid from the address match to the next start bit, stop bit or not ack bit. 3: oring this bit with sen, rsen, pen, rcen or acken will indicate if the mssp is in idle mode. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 168 preliminary ? 2004 microchip technology inc. register 15-4: sspcon1: mssp control register 1 (i 2 c? mode) r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 wcol sspov sspen (1) ckp sspm3 (2) sspm2 (2) sspm1 (2) sspm0 (2) bit 7 bit 0 bit 7 wcol: write collision detect bit in master transmit mode: 1 = a write to the sspbuf register was attempted while the i 2 c conditions were not valid for a transmission to be started (must be cleared in software) 0 = no collision in slave transmit mode: 1 = the sspbuf register is written while it is still transmitting the previous word (must be cleared in software) 0 = no collision in receive mode (master or slave modes): this is a ?don?t care? bit. bit 6 sspov: receive overflow indicator bit in receive mode: 1 = a byte is received while the sspbuf register is still holding the previous byte (must be cleared in software) 0 = no overflow in transmit mode: this is a ?don?t care? bit in transmit mode. bit 5 sspen: synchronous serial port enable bit (1) 1 = enables the serial port and configures the sda and scl pins as the serial port pins 0 = disables serial port and configures these pins as i/o port pins bit 4 ckp: sck release control bit in slave mode: 1 = releases clock 0 = holds clock low (clock stretch), used to ensure data setup time in master mode: unused in this mode. bit 3-0 sspm3:sspm0: synchronous serial port mode select bits (2) 1111 = i 2 c slave mode, 10-bit address with start and stop bit interrupts enabled 1110 = i 2 c slave mode, 7-bit address with start and stop bit interrupts enabled 1011 = i 2 c firmware controlled master mode (slave idle) 1000 = i 2 c master mode, clock = f osc /(4 * (sspadd + 1)) 0111 = i 2 c slave mode, 10-bit address 0110 = i 2 c slave mode, 7-bit address note 1: when enabled, the sda and scl pins must be properly configured as input or output. 2: bit combinations not specifically listed here are either reserved or implemented in spi mode only. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
? 2004 microchip technology inc. preliminary ds39629b-page 169 PIC18F6390/6490/8390/8490 register 15-5: sspcon2: mssp control register 2 (i 2 c? mode) r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 gcen ackstat ackdt (1) acken (2) rcen (2) pen (2) rsen (2) sen (2) bit 7 bit 0 bit 7 gcen: general call enable bit (slave mode only) 1 = enable interrupt when a general call address (0000h) is received in the sspsr 0 = general call address disabled bit 6 ackstat: acknowledge status bit (master transmit mode only) 1 = acknowledge was not received from slave 0 = acknowledge was received from slave bit 5 ackdt: acknowledge data bit (master receive mode only) (1) 1 = not acknowledge 0 = acknowledge bit 4 acken: acknowledge sequence enable bit (master receive mode only) (2) 1 = initiate acknowledge sequence on sda and scl pins and transmit ackdt data bit. automatically cleared by hardware. 0 = acknowledge sequence idle bit 3 rcen: receive enable bit (master mode only) (2) 1 = enables receive mode for i 2 c 0 = receive idle bit 2 pen: stop condition enable bit (master mode only) (2) 1 = initiate stop condition on sda and scl pins. automatically cleared by hardware. 0 = stop condition idle bit 1 rsen: repeated start condition enable bit (master mode only) (2) 1 = initiate repeated start condition on sda and scl pins. automatically cleared by hardware. 0 = repeated start condition idle bit 0 sen: start condition enable/stretch enable bit (2) in master mode: 1 = initiate start condition on sda and scl pins. automatically cleared by hardware. 0 = start condition idle in slave mode: 1 = clock stretching is enabled for both slave transmit and slave receive (stretch enabled) 0 = clock stretching is disabled note 1: value that will be transmitted when the user initiates an acknowledge sequence at the end of a receive. 2: if the i 2 c module is not in the idle mode, this bit may not be set (no spooling) and the sspbuf may not be written (or writes to the sspbuf are disabled). legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 170 preliminary ? 2004 microchip technology inc. 15.4.2 operation the mssp module functions are enabled by setting mssp enable bit, sspen (sspcon<5>). the sspcon1 register allows control of the i 2 c operation. four mode selection bits (sspcon<3:0>) allow one of the following i 2 c modes to be selected: i 2 c master mode, clock = (f osc /4) x (sspadd + 1) i 2 c slave mode (7-bit address) i 2 c slave mode (10-bit address) i 2 c slave mode (7-bit address) with start and stop bit interrupts enabled i 2 c slave mode (10-bit address) with start and stop bit interrupts enabled i 2 c firmware controlled master mode, slave is idle selection of any i 2 c mode with the sspen bit set, forces the scl and sda pins to be open-drain, provided these pins are programmed to inputs by setting the appropriate trisc bits. to ensure proper operation of the module, pull-up resistors must be provided externally to the scl and sda pins. 15.4.3 slave mode in slave mode, the scl and sda pins must be config- ured as inputs (trisc<4:3> set). the mssp module will override the input state with the output data when required (slave-transmitter). the i 2 c slave mode hardware will always generate an interrupt on an address match. through the mode select bits, the user can also choose to interrupt on start and stop bits when an address is matched, or the data transfer after an address match is received, the hardware auto- matically will generate the acknowledge (ack ) pulse and load the sspbuf register with the received value currently in the sspsr register. any combination of the following conditions will cause the mssp module not to give this ack pulse: the buffer full bit, bf (sspstat<0>), was set before the transfer was received. the overflow bit, sspov (sspcon<6>), was set before the transfer was received. in this case, the sspsr register value is not loaded into the sspbuf, but bit sspif (pir1<3>) is set. the bf bit is cleared by reading the sspbuf register, while bit sspov is cleared through software. the scl clock input must have a minimum high and low for proper operation. the high and low times of the i 2 c specification, as well as the requirement of the mssp module, are shown in timing parameter #100 and parameter #101. 15.4.3.1 addressing once the mssp module has been enabled, it waits for a start condition to occur. following the start condition, the 8 bits are shifted into the sspsr register. all incoming bits are sampled with the rising edge of the clock (scl) line. the value of register sspsr<7:1> is compared to the value of the sspadd register. the address is compared on the falling edge of the eighth clock (scl) pulse. if the addresses match and the bf and sspov bits are clear, the following events occur: 1. the sspsr register value is loaded into the sspbuf register. 2. the buffer full bit, bf, is set. 3. an ack pulse is generated. 4. mssp interrupt flag bit, sspif (pir1<3>), is set (interrupt is generated, if enabled) on the falling edge of the ninth scl pulse. in 10-bit address mode, two address bytes need to be received by the slave. the five most significant bits (msbs) of the first address byte specify if this is a 10-bit address. bit r/w (sspstat<2>) must specify a write so the slave device will receive the second address byte. for a 10-bit address, the first byte would equal ? 11110 a9 a8 0 ?, where ? a9 ? and ? a8 ? are the two msbs of the address. the sequence of events for 10-bit address is as follows, with steps 7 through 9 for the slave-transmitter: 1. receive first (high) byte of address (bits sspif, bf and ua (sspstat<1>) are set). 2. update the sspadd register with second (low) byte of address (clears bit ua and releases the scl line). 3. read the sspbuf register (clears bit bf) and clear flag bit sspif. 4. receive second (low) byte of address (bits sspif, bf and ua are set). 5. update the sspadd register with the first (high) byte of address. if match releases scl line, this will clear bit ua. 6. read the sspbuf register (clears bit bf) and clear flag bit sspif. 7. receive repeated start condition. 8. receive first (high) byte of address (bits sspif and bf are set). 9. read the sspbuf register (clears bit bf) and clear flag bit sspif.
? 2004 microchip technology inc. preliminary ds39629b-page 171 PIC18F6390/6490/8390/8490 15.4.3.2 reception when the r/w bit of the address byte is clear and an address match occurs, the r/w bit of the sspstat register is cleared. the received address is loaded into the sspbuf register and the sda line is held low (ack ). when the address byte overflow condition exists, then the no acknowledge (ack ) pulse is given. an overflow condition is defined as either bit bf (sspstat<0>) is set, or bit sspov (sspcon1<6>) is set. an mssp interrupt is generated for each data transfer byte. flag bit, sspif (pir1<3>), must be cleared in software. the sspstat register is used to determine the status of the byte. if sen is enabled (sspcon2<0> = 1 ), rc3/sck/scl will be held low (clock stretch) following each data transfer. the clock must be released by setting bit ckp (sspcon<4>). see section 15.4.4 ?clock stretching? for more detail. 15.4.3.3 transmission when the r/w bit of the incoming address byte is set and an address match occurs, the r/w bit of the sspstat register is set. the received address is loaded into the sspbuf register. the ack pulse will be sent on the ninth bit and pin rc3/sck/scl is held low regardless of sen (see section 15.4.4 ?clock stretching? for more detail). by stretching the clock, the master will be unable to assert another clock pulse until the slave is done preparing the transmit data. the transmit data must be loaded into the sspbuf register which also loads the sspsr register. then, pin rc3/ sck/scl should be enabled by setting bit, ckp (sspcon1<4>). the 8 data bits are shifted out on the falling edge of the scl input. this ensures that the sda signal is valid during the scl high time (figure 15-9). the ack pulse from the master-receiver is latched on the rising edge of the ninth scl input pulse. if the sda line is high (not ack ), then the data transfer is complete. in this case, when the ack is latched by the slave, the slave logic is reset (resets sspstat register) and the slave monitors for another occurrence of the start bit. if the sda line was low (ack ), the next transmit data must be loaded into the sspbuf register. again, pin rc3/sck/scl must be enabled by setting bit ckp. an mssp interrupt is generated for each data transfer byte. the sspif bit must be cleared in software and the sspstat register is used to determine the status of the byte. the sspif bit is set on the falling edge of the ninth clock pulse.
PIC18F6390/6490/8390/8490 ds39629b-page 172 preliminary ? 2004 microchip technology inc. figure 15-8: i 2 c? slave mode timing with sen = 0 (reception, 7-bit address) sda scl sspif bf (sspstat<0>) sspov (sspcon1<6>) s 1 2 3 4 56 7 8 91 2 3 4 5 67 89 1 2 3 4 5 7 8 9 p a7 a6 a5 a4 a3 a2 a1 d7 d6 d5 d4 d3 d2 d1 d0 d7 d6 d5 d4 d3 d1 d0 ack receiving data ack receiving data r/w = 0 ack receiving address cleared in software sspbuf is read bus master terminates transfer sspov is set because sspbuf is still full. ack is not sent. d2 6 (pir1<3>) ckp (ckp does not reset to ? 0 ? when sen = 0 )
? 2004 microchip technology inc. preliminary ds39629b-page 173 PIC18F6390/6490/8390/8490 figure 15-9: i 2 c? slave mode timing (transmission, 7-bit address) sda scl sspif (pir1<3>) bf (sspstat<0>) a6 a5 a4 a3 a2 a1 d6 d5 d4 d3 d2 d1 d0 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 9 sspbuf is written in software cleared in software from sspif isr data in sampled s ack transmitting data r/w = 1 ack receiving address a7 d7 9 1 d6 d5 d4 d3 d2 d1 d0 2 3 4 5 6 7 8 9 sspbuf is written in software cleared in software from sspif isr transmitting data d7 1 ckp p ack ckp is set in software ckp is set in software scl held low while cpu responds to sspif
PIC18F6390/6490/8390/8490 ds39629b-page 174 preliminary ? 2004 microchip technology inc. figure 15-10: i 2 c? slave mode timing with sen = 0 (reception, 10-bit address) sda scl sspif bf (sspstat<0>) s 123456789 123456789 12345 789 p 1 1 1 1 0 a9a8 a7 a6a5a4a3a2a1 a0 d7 d6d5d4d3 d1d0 receive data byte ack r/w = 0 ack receive first byte of address cleared in software d2 6 (pir1<3>) cleared in software receive second byte of address cleared by hardware when sspadd is updated with low byte of address ua (sspstat<1>) clock is held low until update of sspadd has taken place ua is set indicating that the sspadd needs to be updated ua is set indicating that sspadd needs to be updated cleared by hardware when sspadd is updated with high byte of address sspbuf is written with contents of sspsr dummy read of sspbuf to clear bf flag ack ckp 12345 789 d7 d6 d5 d4 d3 d1 d0 receive data byte bus master terminates transfer d2 6 ack cleared in software cleared in software sspov (sspcon1<6>) sspov is set because sspbuf is still full. ack is not sent. (ckp does not reset to ? 0 ? when sen = 0 ) clock is held low until update of sspadd has taken place
? 2004 microchip technology inc. preliminary ds39629b-page 175 PIC18F6390/6490/8390/8490 figure 15-11: i 2 c? slave mode timing (transmission, 10-bit address) sda scl sspif bf (sspstat<0>) s 1234 5 6789 1 2345 678 9 12345 78 9 p 1 1 1 1 0 a9a8 a7 a6a5a4a3a2a1a0 1 1 1 1 0 a8 r/w = 1 ack ack r/w = 0 ack receive first byte of address cleared in software bus master terminates transfer a9 6 (pir1<3>) receive second byte of address cleared by hardware when sspadd is updated with low byte of address ua (sspstat<1>) clock is held low until update of sspadd has taken place ua is set indicating that the sspadd needs to be updated ua is set indicating that sspadd needs to be updated cleared by hardware when sspadd is updated with high byte of address. sspbuf is written with contents of sspsr dummy read of sspbuf to clear bf flag receive first byte of address 12345 789 d7 d6 d5 d4 d3 d1 ack d2 6 transmitting data byte d0 dummy read of sspbuf to clear bf flag sr cleared in software write of sspbuf initiates transmit cleared in software completion of clears bf flag ckp (sspcon1<4>) ckp is set in software ckp is automatically cleared in hardware, holding scl low clock is held low until update of sspadd has taken place data transmission clock is held low until ckp is set to ? 1 ? bf flag is clear third address sequence at the end of the
PIC18F6390/6490/8390/8490 ds39629b-page 176 preliminary ? 2004 microchip technology inc. 15.4.4 clock stretching both 7 and 10-bit slave modes implement automatic clock stretching during a transmit sequence. the sen bit (sspcon2<0>) allows clock stretching to be enabled during receives. setting sen will cause the scl pin to be held low at the end of each data receive sequence. 15.4.4.1 clock stretching for 7-bit slave receive mode (sen = 1 ) in 7-bit slave receive mode, on the falling edge of the ninth clock at the end of the ack sequence, if the bf bit is set, the ckp bit in the sspcon1 register is automatically cleared, forcing the scl output to be held low. the ckp being cleared to ? 0 ? will assert the scl line low. the ckp bit must be set in the user?s isr before reception is allowed to continue. by holding the scl line low, the user has time to service the isr and read the contents of the sspbuf before the master device can initiate another receive sequence. this will prevent buffer overruns from occurring (see figure 15-13). 15.4.4.2 clock stretching for 10-bit slave receive mode (sen = 1 ) in 10-bit slave receive mode during the address sequence, clock stretching automatically takes place but ckp is not cleared. during this time, if the ua bit is set after the ninth clock, clock stretching is initiated. the ua bit is set after receiving the upper byte of the 10-bit address and following the receive of the second byte of the 10-bit address with the r/w bit cleared to ? 0 ?. the release of the clock line occurs upon updating sspadd. clock stretching will occur on each data receive sequence as described in 7-bit mode. 15.4.4.3 clock stretching for 7-bit slave transmit mode 7-bit slave transmit mode implements clock stretching by clearing the ckp bit after the falling edge of the ninth clock, if the bf bit is clear. this occurs regardless of the state of the sen bit. the user?s isr must set the ckp bit before transmis- sion is allowed to continue. by holding the scl line low, the user has time to service the isr and load the contents of the sspbuf before the master device can initiate another transmit sequence (see figure 15-9). 15.4.4.4 clock stretching for 10-bit slave transmit mode in 10-bit slave transmit mode, clock stretching is controlled during the first two address sequences by the state of the ua bit, just as it is in 10-bit slave receive mode. the first two addresses are followed by a third address sequence which contains the high- order bits of the 10-bit address and the r/w bit set to ? 1 ?. after the third address sequence is performed, the ua bit is not set, the module is now configured in transmit mode and clock stretching is controlled by the bf flag as in 7-bit slave transmit mode (see figure 15-11). note 1: if the user reads the contents of the sspbuf before the falling edge of the ninth clock, thus clearing the bf bit, the ckp bit will not be cleared and clock stretching will not occur. 2: the ckp bit can be set in software regardless of the state of the bf bit. the user should be careful to clear the bf bit in the isr before the next receive sequence in order to prevent an overflow condition. note: if the user polls the ua bit and clears it by updating the sspadd register before the falling edge of the ninth clock occurs and if the user hasn?t cleared the bf bit by read- ing the sspbuf register before that time, then the ckp bit will still not be asserted low. clock stretching on the basis of the state of the bf bit only occurs during a data sequence, not an address sequence. note 1: if the user loads the contents of sspbuf, setting the bf bit before the falling edge of the ninth clock, the ckp bit will not be cleared and clock stretching will not occur. 2: the ckp bit can be set in software regardless of the state of the bf bit.
? 2004 microchip technology inc. preliminary ds39629b-page 177 PIC18F6390/6490/8390/8490 15.4.4.5 clock synchronization and the ckp bit when the ckp bit is cleared, the scl output is forced to ? 0 ?. however, setting the ckp bit will not assert the scl output low until the scl output is already sam- pled low. therefore, the ckp bit will not assert the scl line until an external i 2 c master device has already asserted the scl line. the scl output will remain low until the ckp bit is set and all other devices on the i 2 c bus have deasserted scl. this ensures that a write to the ckp bit will not violate the minimum high time requirement for scl (see figure 15-12). figure 15-12: clock synchronization timing sda scl dx ? 1 dx wr q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 sspcon ckp master device deasserts clock master device asserts clock
PIC18F6390/6490/8390/8490 ds39629b-page 178 preliminary ? 2004 microchip technology inc. figure 15-13: i 2 c? slave mode timing with sen = 1 (reception, 7-bit address) sda scl sspif bf (sspstat<0>) sspov (sspcon1<6>) s 1 234 567 89 1 2345 67 89 1 23 45 7 89 p a7 a6 a5 a4 a3 a2 a1 d7 d6 d5 d4 d3 d2 d1 d0 d7 d6 d5 d4 d3 d1 d0 ack receiving data ack receiving data r/w = 0 ack receiving address cleared in software sspbuf is read bus master terminates transfer sspov is set because sspbuf is still full. ack is not sent. d2 6 (pir1<3>) ckp ckp written to ? 1 ? in if bf is cleared prior to the falling edge of the 9th clock, ckp will not be reset to ? 0 ? and no clock stretching will occur software clock is held low until ckp is set to ? 1 ? clock is not held low because buffer full bit is clear prior to falling edge of 9th clock clock is not held low because ack = 1 bf is set after falling edge of the 9th clock, ckp is reset to ? 0 ? and clock stretching occurs
? 2004 microchip technology inc. preliminary ds39629b-page 179 PIC18F6390/6490/8390/8490 figure 15-14: i 2 c? slave mode timing with sen = 1 (reception, 10-bit address) sda scl sspif bf (sspstat<0>) s 123456789 123456789 12345 789 p 1 1 1 1 0 a9a8 a7 a6a5a4a3a2a1 a0 d7d6d5d4d3 d1d0 receive data byte ack r/w = 0 ack receive first byte of address cleared in software d2 6 (pir1<3>) cleared in software receive second byte of address cleared by hardware when sspadd is updated with low byte of address after falling edge ua (sspstat<1>) clock is held low until update of sspadd has taken place ua is set indicating that the sspadd needs to be updated ua is set indicating that sspadd needs to be updated cleared by hardware when sspadd is updated with high byte of address after falling edge sspbuf is written with contents of sspsr dummy read of sspbuf to clear bf flag ack ckp 12345 789 d7 d6 d5 d4 d3 d1 d0 receive data byte bus master terminates transfer d2 6 ack cleared in software cleared in software sspov (sspcon1<6>) ckp written to ? 1 ? note: an update of the sspadd register before the falling edge of the ninth clock will have no effect on ua and ua will remain set. note: an update of the sspadd register before the falling edge of the ninth clock will have no effect on ua and ua will remain set. in software clock is held low until update of sspadd has taken place of ninth clock of ninth clock sspov is set because sspbuf is still full. ack is not sent. dummy read of sspbuf to clear bf flag clock is held low until ckp is set to ? 1 ? clock is not held low because ack = 1
PIC18F6390/6490/8390/8490 ds39629b-page 180 preliminary ? 2004 microchip technology inc. 15.4.5 general call address support the addressing procedure for the i 2 c bus is such that the first byte after the start condition usually deter- mines which device will be the slave addressed by the master. the exception is the general call address which can address all devices. when this address is used, all devices should, in theory, respond with an acknowledge. the general call address is one of eight addresses reserved for specific purposes by the i 2 c protocol. it consists of all ? 0 ?s with r/w = 0 . the general call address is recognized when the general call enable bit (gcen) is enabled (sspcon2<7> set). following a start bit detect, 8 bits are shifted into the sspsr and the address is compared against the sspadd. it is also compared to the general call address and fixed in hardware. if the general call address matches, the sspsr is transferred to the sspbuf, the bf flag bit is set (eighth bit) and on the falling edge of the ninth bit (ack bit), the sspif interrupt flag bit is set. when the interrupt is serviced, the source for the inter- rupt can be checked by reading the contents of the sspbuf. the value can be used to determine if the address was device specific or a general call address. in 10-bit mode, the sspadd is required to be updated for the second half of the address to match and the ua bit is set (sspstat<1>). if the general call address is sampled when the gcen bit is set, while the slave is configured in 10-bit address mode, then the second half of the address is not necessary, the ua bit will not be set and the slave will begin receiving data after the acknowledge (figure 15-15). figure 15-15: slave mode general call address sequence (7 or 10-bit address mode) sda scl s sspif bf (sspstat<0>) sspov (sspcon1<6>) cleared in software sspbuf is read r/w = 0 ack general call address address is compared to general call address gcen (sspcon2<7>) receiving data ack 123456789123456789 d7 d6 d5 d4 d3 d2 d1 d0 after ack , set interrupt ? 0 ? ? 1 ?
? 2004 microchip technology inc. preliminary ds39629b-page 181 PIC18F6390/6490/8390/8490 15.4.6 master mode master mode is enabled by setting and clearing the appropriate sspm bits in sspcon1 and by setting the sspen bit. in master mode, the scl and sda lines are manipulated by the mssp hardware. master mode of operation is supported by interrupt generation on the detection of the start and stop conditions. the stop (p) and start (s) bits are cleared from a reset or when the mssp module is disabled. control of the i 2 c bus may be taken when the p bit is set or the bus is idle, with both the s and p bits clear. in firmware controlled master mode, user code conducts all i 2 c bus operations based on start and stop bit conditions. once master mode is enabled, the user has six options. 1. assert a start condition on sda and scl. 2. assert a repeated start condition on sda and scl. 3. write to the sspbuf register initiating transmission of data/address. 4. configure the i 2 c port to receive data. 5. generate an acknowledge condition at the end of a received byte of data. 6. generate a stop condition on sda and scl. the following events will cause the ssp interrupt flag bit, sspif, to be set (ssp interrupt, if enabled): start condition stop condition data transfer byte transmitted/received acknowledge transmit repeated start figure 15-16: mssp block diagram (i 2 c? master mode) note: the mssp module, when configured in i 2 c master mode, does not allow queueing of events. for instance, the user is not allowed to initiate a start condition and immediately write the sspbuf register to initiate transmission before the start condi- tion is complete. in this case, the sspbuf will not be written to and the wcol bit will be set, indicating that a write to the sspbuf did not occur. read write sspsr start bit, stop bit, sspbuf internal data bus set/reset, s, p, wcol (sspstat) shift clock msb lsb sda acknowledge generate stop bit detect write collision detect clock arbitration state counter for end of xmit/rcv scl scl in bus collision sda in receive enable clock cntl clock arbitrate/wcol detect (hold off clock source) sspadd<6:0> baud set sspif, bclif reset ackstat, pen (sspcon2) rate generator sspm3:sspm0 start bit detect
PIC18F6390/6490/8390/8490 ds39629b-page 182 preliminary ? 2004 microchip technology inc. 15.4.6.1 i 2 c master mode operation the master device generates all of the serial clock pulses and the start and stop conditions. a transfer is ended with a stop condition or with a repeated start condition. since the repeated start condition is also the beginning of the next serial transfer, the i 2 c bus will not be released. in master transmitter mode, serial data is output through sda, while scl outputs the serial clock. the first byte transmitted contains the slave address of the receiving device (7 bits) and the read/write (r/w ) bit. in this case, the r/w bit will be logic ? 0 ?. serial data is transmitted 8 bits at a time. after each byte is transmit- ted, an acknowledge bit is received. start and stop conditions are output to indicate the beginning and the end of a serial transfer. in master receive mode, the first byte transmitted contains the slave address of the transmitting device (7 bits) and the r/w bit. in this case, the r/w bit will be logic ? 1 ?. thus, the first byte transmitted is a 7-bit slave address, followed by a ? 1 ? to indicate the receive bit. serial data is received via sda, while scl outputs the serial clock. serial data is received 8 bits at a time. after each byte is received, an acknowledge bit is transmit- ted. start and stop conditions indicate the beginning and end of transmission. the baud rate generator used for the spi mode operation is used to set the scl clock frequency for either 100 khz, 400 khz or 1 mhz i 2 c operation. see section 15.4.7 ?baud rate? for more detail. a typical transmit sequence would go as follows: 1. the user generates a start condition by setting the start enable bit, sen (sspcon2<0>). 2. sspif is set. the mssp module will wait the required start time before any other operation takes place. 3. the user loads the sspbuf with the slave address to transmit. 4. address is shifted out the sda pin until all 8 bits are transmitted. 5. the mssp module shifts in the ack bit from the slave device and writes its value into the sspcon2 register (sspcon2<6>). 6. the mssp module generates an interrupt at the end of the ninth clock cycle by setting the sspif bit. 7. the user loads the sspbuf with 8 bits of data. 8. data is shifted out the sda pin until all 8 bits are transmitted. 9. the mssp module shifts in the ack bit from the slave device and writes its value into the sspcon2 register (sspcon2<6>). 10. the mssp module generates an interrupt at the end of the ninth clock cycle by setting the sspif bit. 11. the user generates a stop condition by setting the stop enable bit, pen (sspcon2<2>). 12. interrupt is generated once the stop condition is complete.
? 2004 microchip technology inc. preliminary ds39629b-page 183 PIC18F6390/6490/8390/8490 15.4.7 baud rate in i 2 c master mode, the baud rate generator (brg) reload value is placed in the lower 7 bits of the sspadd register (figure 15-17). when a write occurs to sspbuf, the baud rate generator will automatically begin counting. the brg counts down to ? 0 ? and stops until another reload has taken place. the brg count is decremented twice per instruction cycle (t cy ) on the q2 and q4 clocks. in i 2 c master mode, the brg is reloaded automatically. once the given operation is complete (i.e., transmis- sion of the last data bit is followed by ack ), the internal clock will automatically stop counting and the scl pin will remain in its last state. table 15-3 demonstrates clock rates based on instruction cycles and the brg value loaded into sspadd. figure 15-17: baud rate generator block diagram table 15-3: i 2 c? clock rate w/brg sspm3:sspm0 brg down counter clko f osc /4 sspadd<6:0> sspm3:sspm0 scl reload control reload f cy f cy *2 brg value f scl (2 rollovers of brg) 10 mhz 20 mhz 19h 400 khz (1) 10 mhz 20 mhz 20h 312.5 khz 10 mhz 20 mhz 3fh 100 khz 4 mhz 8 mhz 0ah 400 khz (1) 4 mhz 8 mhz 0dh 308 khz 4 mhz 8 mhz 28h 100 khz 1 mhz 2 mhz 03h 333 khz (1) 1 mhz 2 mhz 0ah 100 khz 1 mhz 2 mhz 00h 1 mhz (1) note 1: the i 2 c interface does not conform to the 400 khz i 2 c specification (which applies to rates greater than 100 khz) in all details, but may be used with care where higher rates are required by the application.
PIC18F6390/6490/8390/8490 ds39629b-page 184 preliminary ? 2004 microchip technology inc. 15.4.7.1 clock arbitration clock arbitration occurs when the master, during any receive, transmit or repeated start/stop condition, deasserts the scl pin (scl allowed to float high). when the scl pin is allowed to float high, the baud rate generator (brg) is suspended from counting until the scl pin is actually sampled high. when the scl pin is sampled high, the baud rate generator is reloaded with the contents of sspadd<6:0> and begins counting. this ensures that the scl high time will always be at least one brg rollover count in the event that the clock is held low by an external device (figure 15-18). figure 15-18: baud rate generator timing with clock arbitration sda scl scl deasserted but slave holds dx ? 1 dx brg scl is sampled high, reload takes place and brg starts its count 03h 02h 01h 00h (hold off) 03h 02h reload brg value scl low (clock arbitration) scl allowed to transition high brg decrements on q2 and q4 cycles
? 2004 microchip technology inc. preliminary ds39629b-page 185 PIC18F6390/6490/8390/8490 15.4.8 i 2 c master mode start condition timing to initiate a start condition, the user sets the start condition enable bit, sen (sspcon2<0>). if the sda and scl pins are sampled high, the baud rate gener- ator is reloaded with the contents of sspadd<6:0> and starts its count. if scl and sda are both sampled high when the baud rate generator times out (t brg ), the sda pin is driven low. the action of the sda being driven low while scl is high is the start condition and causes the s bit (sspstat<3>) to be set. following this, the baud rate generator is reloaded with the contents of sspadd<6:0> and resumes its count. when the baud rate generator times out (t brg ), the sen bit (sspcon2<0>) will be automatically cleared by hardware, the baud rate generator is suspended, leaving the sda line held low and the start condition is complete. 15.4.8.1 wcol status flag if the user writes the sspbuf when a start sequence is in progress, the wcol is set and the contents of the buffer are unchanged (the write doesn?t occur). figure 15-19: first start bit timing note: if at the beginning of the start condition, the sda and scl pins are already sam- pled low, or if during the start condition, the scl line is sampled low before the sda line is driven low, a bus collision occurs, the bus collision interrupt flag, bclif, is set, the start condition is aborted and the i 2 c module is reset into its idle state. note: because queueing of events is not allowed, writing to the lower 5 bits of sspcon2 is disabled until the start condition is complete. sda scl s t brg 1st bit 2nd bit t brg sda = 1 , at completion of start bit, scl = 1 write to sspbuf occurs here t brg hardware clears sen bit t brg write to sen bit occurs here set s bit (sspstat<3>) and sets sspif bit
PIC18F6390/6490/8390/8490 ds39629b-page 186 preliminary ? 2004 microchip technology inc. 15.4.9 i 2 c master mode repeated start condition timing a repeated start condition occurs when the rsen bit (sspcon2<1>) is programmed high and the i 2 c logic module is in the idle state. when the rsen bit is set, the scl pin is asserted low. when the scl pin is sampled low, the baud rate generator is loaded with the contents of sspadd<5:0> and begins counting. the sda pin is released (brought high) for one baud rate generator count (t brg ). when the baud rate generator times out, if sda is sampled high, the scl pin will be deasserted (brought high). when scl is sampled high, the baud rate generator is reloaded with the contents of sspadd<6:0> and begins count- ing. sda and scl must be sampled high for one t brg . this action is then followed by assertion of the sda pin (sda = 0 ) for one t brg while scl is high. following this, the rsen bit (sspcon2<1>) will be automatically cleared and the baud rate generator will not be reloaded, leaving the sda pin held low. as soon as a start condition is detected on the sda and scl pins, the s bit (sspstat<3>) will be set. the sspif bit will not be set until the baud rate generator has timed out. immediately following the sspif bit getting set, the user may write the sspbuf with the 7-bit address in 7-bit mode, or the default first address in 10-bit mode. after the first 8 bits are transmitted and an ack is received, the user may then transmit an additional eight bits of address (10-bit mode) or 8 bi ts of data (7-bit mode). 15.4.9.1 wcol status flag if the user writes the sspbuf when a repeated start sequence is in progress, the wcol is set and the contents of the buffer are unchanged (the write doesn?t occur). figure 15-20: repeat start condition waveform note 1: if rsen is programmed while any other event is in progress, it will not take effect. 2: a bus collision during the repeated start condition occurs if: sda is sampled low when scl goes from low-to-high. scl goes low before sda is asserted low. this may indicate that another master is attempting to transmit a data ? 1 ?. note: because queueing of events is not allowed, writing of the lower 5 bits of sspcon2 is disabled until the repeated start condition is complete. sda scl sr = repeated start write to sspcon2 write to sspbuf occurs here falling edge of ninth clock, end of xmit at completion of start bit, hardware clears rsen bit 1st bit set s (sspstat<3>) t brg t brg sda = 1 , sda = 1 , scl (no change). scl = 1 occurs here. t brg t brg t brg and sets sspif
? 2004 microchip technology inc. preliminary ds39629b-page 187 PIC18F6390/6490/8390/8490 15.4.10 i 2 c master mode transmission transmission of a data byte, a 7-bit address or the other half of a 10-bit address is accomplished by simply writing a value to the sspbuf register. this action will set the buffer full flag bit, bf and allow the baud rate generator to begin counting and start the next trans- mission. each bit of address/data will be shifted out onto the sda pin after the falling edge of scl is asserted (see data hold time specification parameter #106). scl is held low for one baud rate generator rollover count (t brg ). data should be valid before scl is released high (see data setup time specification parameter #107). when the scl pin is released high, it is held that way for t brg . the data on the sda pin must remain stable for that duration and some hold time after the next falling edge of scl. after the eighth bit is shifted out (the falling edge of the eighth clock), the bf flag is cleared and the master releases sda. this allows the slave device being addressed to respond with an ack bit during the ninth bit time if an address match occurred, or if data was received properly. the status of ack is written into the ackdt bit on the falling edge of the ninth clock. if the master receives an acknowledge, the acknowledge status bit, ackstat, is cleared. if not, the bit is set. after the ninth clock, the sspif bit is set and the master clock (baud rate generator) is suspended until the next data byte is loaded into the sspbuf, leaving scl low and sda unchanged (figure 15-21). after the write to the sspbuf, each bit of address will be shifted out on the falling edge of scl until all 7 address bits and the r/w bit are completed. on the falling edge of the eighth clock, the master will deassert the sda pin, allowing the slave to respond with an acknowledge. on the falling edge of the ninth clock, the master will sample the sda pin to see if the address was recognized by a slave. the status of the ack bit is loaded into the ackstat status bit (sspcon2<6>). following the falling edge of the ninth clock transmis- sion of the address, the sspif is set, the bf flag is cleared and the baud rate generator is turned off until another write to the sspbuf takes place, holding scl low and allowing sda to float. 15.4.10.1 bf status flag in transmit mode, the bf bit (sspstat<0>) is set when the cpu writes to sspbuf and is cleared when all 8 bits are shifted out. 15.4.10.2 wcol status flag if the user writes the sspbuf when a transmit is already in progress (i.e., sspsr is still shifting out a data byte), the wcol is set and the contents of the buffer are unchanged (the write doesn?t occur). wcol must be cleared in software. 15.4.10.3 ackstat status flag in transmit mode, the ackstat bit (sspcon2<6>) is cleared when the slave has sent an acknowledge (ack = 0 ) and is set when the slave does not acknowl- edge (ack = 1 ). a slave sends an acknowledge when it has recognized its address (including a general call), or when the slave has properly received its data. 15.4.11 i 2 c master mode reception master mode reception is enabled by programming the receive enable bit, rcen (sspcon2<3>). the baud rate generator begins counting and on each rollover, the state of the scl pin changes (high-to-low/ low-to-high) and data is shifted into the sspsr. after the falling edge of the eighth clock, the receive enable flag is automatically cleared, the contents of the sspsr are loaded into the sspbuf, the bf flag bit is set, the sspif flag bit is set and the baud rate generator is suspended from counting, holding scl low. the mssp is now in idle state awaiting the next command. when the buffer is read by the cpu, the bf flag bit is automatically cleared. the user can then send an acknowledge bit at the end of reception by setting the acknowledge sequence enable bit, acken (sspcon2<4>). 15.4.11.1 bf status flag in receive operation, the bf bit is set when an address or data byte is loaded into sspbuf from sspsr. it is cleared when the sspbuf register is read. 15.4.11.2 sspov status flag in receive operation, the sspov bit is set when 8 bits are received into the sspsr and the bf flag bit is already set from a previous reception. 15.4.11.3 wcol status flag if the user writes the sspbuf when a receive is already in progress (i.e., sspsr is still shifting in a data byte), the wcol bit is set and the contents of the buffer are unchanged (the write doesn?t occur). note: the mssp module must be in an idle state before the rcen bit is set or the rcen bit will be disregarded.
PIC18F6390/6490/8390/8490 ds39629b-page 188 preliminary ? 2004 microchip technology inc. figure 15-21: i 2 c? master mode waveform (transmission, 7 or 10-bit address) sda scl sspif bf (sspstat<0>) sen a7 a6 a5 a4 a3 a2 a1 ack = 0 d7 d6 d5 d4 d3 d2 d1 d0 ack transmitting data or second half r/w = 0 transmit address to slave 123456789 123456789 p cleared in software service routine sspbuf is written in software from ssp interrupt after start condition, sen cleared by hardware s sspbuf written with 7-bit address and r/w start transmit scl held low while cpu responds to sspif sen = 0 of 10-bit address write sspcon2<0> sen = 1 start condition begins from slave, clear ackstat bit sspcon2<6> ackstat in sspcon2 = 1 cleared in software sspbuf written pen r/w cleared in software
? 2004 microchip technology inc. preliminary ds39629b-page 189 PIC18F6390/6490/8390/8490 figure 15-22: i 2 c? master mode waveform (reception, 7-bit address) p 9 8 7 6 5 d0 d1 d2 d3 d4 d5 d6 d7 s a7 a6 a5 a4 a3 a2 a1 sda scl 123456789 12345678 9 1234 bus master terminates transfer ack receiving data from slave receiving data from slave d0 d1 d2 d3 d4 d5 d6 d7 ack r/w = 1 transmit address to slave sspif bf ack is not sent write to sspcon2<0> (sen = 1 ), write to sspbuf occurs here, ack from slave master configured as a receiver by programming sspcon2<3> (rcen = 1 ) pen bit = 1 written here data shifted in on falling edge of clk cleared in software start xmit sen = 0 sspov sda = 0 , scl = 1 while cpu (sspstat<0>) ack cleared in software cleared in software set sspif interrupt at end of receive set p bit (sspstat<4>) and sspif cleared in software ack from master set sspif at end set sspif interrupt at end of acknowledge sequence set sspif interrupt at end of acknow- ledge sequence of receive set acken, start acknowledge sequence sda = ackdt = 1 rcen cleared automatically rcen = 1 , start next receive write to sspcon2<4> to start acknowledge sequence sda = ackdt (sspcon2<5>) = 0 rcen cleared automatically responds to sspif acken begin start condition cleared in software sda = ackdt = 0 sspov is set because sspbuf is still full last bit is shifted into sspsr and contents are unloaded into sspbuf
PIC18F6390/6490/8390/8490 ds39629b-page 190 preliminary ? 2004 microchip technology inc. 15.4.12 acknowledge sequence timing an acknowledge sequence is enabled by setting the acknowledge sequence enable bit, acken (sspcon2<4>). when this bit is set, the scl pin is pulled low and the contents of the acknowledge data bit are presented on the sda pin. if the user wishes to gen- erate an acknowledge, then the ackdt bit should be cleared. if not, the user should set the ackdt bit before starting an acknowledge sequence. the baud rate generator then counts for one rollover period (t brg ) and the scl pin is deasserted (pulled high). when the scl pin is sampled high (clock arbitration), the baud rate generator counts for t brg . the scl pin is then pulled low. following this, the acken bit is automatically cleared, the baud rate generator is turned off and the mssp module then goes into idle mode (figure 15-23). 15.4.12.1 wcol status flag if the user writes the sspbuf when an acknowledge sequence is in progress, then wcol is set and the contents of the buffer are unchanged (the write doesn?t occur). 15.4.13 stop condition timing a stop bit is asserted on the sda pin at the end of a receive/transmit by setting the stop sequence enable bit, pen (sspcon2<2>). at the end of a receive/ transmit, the scl line is held low after the falling edge of the ninth clock. when the pen bit is set, the master will assert the sda line low. when the sda line is sampled low, the baud rate generator is reloaded and counts down to ? 0 ?. when the baud rate generator times out, the scl pin will be brought high and one t brg (baud rate generator rollover count) later, the sda pin will be deasserted. when the sda pin is sam- pled high while scl is high, the p bit (sspstat<4>) is set. a t brg later, the pen bit is cleared and the sspif bit is set (figure 15-24). 15.4.13.1 wcol status flag if the user writes the sspbuf when a stop sequence is in progress, then the wcol bit is set and the contents of the buffer are unchanged (the write doesn?t occur). figure 15-23: acknowledge sequence waveform figure 15-24: stop cond ition receive or transmit mode note: t brg = one baud rate generator period. sda scl set sspif at the end acknowledge sequence starts here, write to sspcon2 acken automatically cleared cleared in t brg t brg of receive 8 acken = 1 , ackdt = 0 d0 9 sspif software set sspif at the end of acknowledge sequence cleared in software ack scl sda sda asserted low before rising edge of clock write to sspcon2, set pen falling edge of scl = 1 for t brg , followed by sda = 1 for t brg 9th clock scl brought high after t brg note: t brg = one baud rate generator period. t brg t brg after sda sampled high. p bit (sspstat<4>) is set. t brg to setup stop condition ack p t brg pen bit (sspcon2<2>) is cleared by hardware and the sspif bit is set
? 2004 microchip technology inc. preliminary ds39629b-page 191 PIC18F6390/6490/8390/8490 15.4.14 sleep operation while in sleep mode, the i 2 c module can receive addresses or data and when an address match or complete byte transfer occurs, wake the processor from sleep (if the mssp interrupt is enabled). 15.4.15 effect of a reset a reset disables the mssp module and terminates the current transfer. 15.4.16 multi-master mode in multi-master mode, the interrupt generation on the detection of the start and stop conditions allows the determination of when the bus is free. the stop (p) and start (s) bits are cleared from a reset or when the mssp module is disabled. control of the i 2 c bus may be taken when the p bit (sspstat<4>) is set, or the bus is idle, with both the s and p bits clear. when the bus is busy, enabling the ssp interrupt will generate the interrupt when the stop condition occurs. in multi-master operation, the sda line must be monitored for arbitration to see if the signal level is the expected output level. this check is performed in hardware with the result placed in the bclif bit. the states where arbitration can be lost are: address transfer data transfer a start condition a repeated start condition an acknowledge condition 15.4.17 multi-master communication, bus collision and bus arbitration multi-master mode support is achieved by bus arbitra- tion. when the master outputs address/data bits onto the sda pin, arbitration takes place when the master outputs a ? 1 ? on sda, by letting sda float high and another master asserts a ? 0 ?. when the scl pin floats high, data should be stable. if the expected data on sda is a ? 1 ? and the data sampled on the sda pin = 0 , then a bus collision has taken place. the master will set the bus collision interrupt flag, bclif and reset the i 2 c port to its idle state (figure 15-25). if a transmit was in progress when the bus collision occurred, the transmission is halted, the bf flag is cleared, the sda and scl lines are deasserted and the sspbuf can be written to. when the user services the bus collision interrupt service routine and if the i 2 c bus is free, the user can resume communication by asserting a start condition. if a start, repeated start, stop or acknowledge condition was in progress when the bus collision occurred, the condition is aborted, the sda and scl lines are deasserted and the respective control bits in the sspcon2 register are cleared. when the user ser- vices the bus collision interrupt service routine and if the i 2 c bus is free, the user can resume communication by asserting a start condition. the master will continue to monitor the sda and scl pins. if a stop condition occurs, the sspif bit will be set. a write to the sspbuf will start the transmission of data at the first data bit, regardless of where the transmitter left off when the bus collision occurred. in multi-master mode, the interrupt generation on the detection of start and stop conditions allows the deter- mination of when the bus is free. control of the i 2 c bus can be taken when the p bit is set in the sspstat register, or the bus is idle and the s and p bits are cleared. figure 15-25: bus collision timing for transmit and acknowledge sda scl bclif sda released sda line pulled low by another source sample sda. while scl is high, data doesn?t match what is driven bus collision has occurred. set bus collision interrupt (bclif) by the master. by master data changes while scl = 0
PIC18F6390/6490/8390/8490 ds39629b-page 192 preliminary ? 2004 microchip technology inc. 15.4.17.1 bus collision during a start condition during a start condition, a bus collision occurs if: a) sda or scl are sampled low at the beginning of the start condition (figure 15-26). b) scl is sampled low before sda is asserted low (figure 15-27). during a start condition, both the sda and the scl pins are monitored. if the sda pin is already low, or the scl pin is already low, then all of the following occur: the start condition is aborted, the bclif flag is set and the mssp module is reset to its idle state (figure 15-26). the start condition begins with the sda and scl pins deasserted. when the sda pin is sampled high, the baud rate generator is loaded from sspadd<6:0> and counts down to ? 0 ?. if the scl pin is sampled low while sda is high, a bus collision occurs because it is assumed that another master is attempting to drive a data ? 1 ? during the start condition. if the sda pin is sampled low during this count, the brg is reset and the sda line is asserted early (figure 15-28). if, however, a ? 1 ? is sampled on the sda pin, the sda pin is asserted low at the end of the brg count. the baud rate generator is then reloaded and counts down to ? 0 ? and during this time, if the scl pins are sampled as ? 0 ?, a bus collision does not occur. at the end of the brg count, the scl pin is asserted low. figure 15-26: bus collision during start condition (sda only) note: the reason that bus collision is not a factor during a start condition is that no two bus masters can assert a start condition at the exact same time. therefore, one master will always assert sda before the other. this condition does not cause a bus collision because the two masters must be allowed to arbitrate the first address follow- ing the start condition. if the address is the same, arbitration must be allowed to continue into the data portion, repeated start or stop conditions. sda scl sen sda sampled low before sda goes low before the sen bit is set. s bit and sspif set because ssp module reset into idle state. sen cleared automatically because of bus collision. s bit and sspif set because set sen, enable start condition if sda = 1 , scl = 1 sda = 0 , scl = 1 . bclif s sspif sda = 0 , scl = 1 . sspif and bclif are cleared in software sspif and bclif are cleared in software set bclif, start condition. set bclif.
? 2004 microchip technology inc. preliminary ds39629b-page 193 PIC18F6390/6490/8390/8490 figure 15-27: bus collision d uring start condition (scl = 0 ) figure 15-28: brg reset due to sda arbitrat ion during start condition sda scl sen bus collision occurs. set bclif. scl = 0 before sda = 0 , set sen, enable start sequence if sda = 1 , scl = 1 t brg t brg sda = 0 , scl = 1 bclif s sspif interrupt cleared in software bus collision occurs. set bclif. scl = 0 before brg time-out, ? 0 ?? 0 ? ? 0 ? ? 0 ? sda scl sen set s less than t brg t brg sda = 0 , scl = 1 bclif s sspif s interrupts cleared in software set sspif sda = 0 , scl = 1 , scl pulled low after brg time-out set sspif ? 0 ? sda pulled low by other master. reset brg and assert sda. set sen, enable start sequence if sda = 1 , scl = 1
PIC18F6390/6490/8390/8490 ds39629b-page 194 preliminary ? 2004 microchip technology inc. 15.4.17.2 bus collision during a repeated start condition during a repeated start condition, a bus collision occurs if: a) a low level is sampled on sda when scl goes from low level to high level. b) scl goes low before sda is asserted low, indicating that another master is attempting to transmit a data ? 1 ?. when the user deasserts sda and the pin is allowed to float high, the brg is loaded with sspadd<6:0> and counts down to ? 0 ?. the scl pin is then deasserted and when sampled high, the sda pin is sampled. if sda is low, a bus collision has occurred (i.e., another master is attempting to transmit a data ? 0 ?, figure 15-29). if sda is sampled high, the brg is reloaded and begins counting. if sda goes from high-to-low before the brg times out, no bus collision occurs because no two masters can assert sda at exactly the same time. if scl goes from high-to-low before the brg times out and sda has not already been asserted, a bus collision occurs. in this case, another master is attempting to transmit a data ? 1 ? during the repeated start condition (see figure 15-30). if, at the end of the brg time-out, both scl and sda are still high, the sda pin is driven low and the brg is reloaded and begins counting. at the end of the count, regardless of the status of the scl pin, the scl pin is driven low and the repeated start condition is complete. figure 15-29: bus collision during a repeat ed start condition (case 1) figure 15-30: bus collision during repeat ed start condition (case 2) sda scl rsen bclif s sspif sample sda when scl goes high. if sda = 0 , set bclif and release sda and scl. cleared in software ? 0 ? ? 0 ? sda scl bclif rsen s sspif interrupt cleared in software scl goes low before sda, set bclif. release sda and scl. t brg t brg ? 0 ?
? 2004 microchip technology inc. preliminary ds39629b-page 195 PIC18F6390/6490/8390/8490 15.4.17.3 bus collision during a stop condition bus collision occurs during a stop condition if: a) after the sda pin has been deasserted and allowed to float high, sda is sampled low after the brg has timed out. b) after the scl pin is deasserted, scl is sampled low before sda goes high. the stop condition begins with sda asserted low. when sda is sampled low, the scl pin is allowed to float. when the pin is sampled high (clock arbitration), the baud rate generator is loaded with sspadd<6:0> and counts down to ? 0 ?. after the brg times out, sda is sampled. if sda is sampled low, a bus collision has occurred. this is due to another master attempting to drive a data ? 0 ? (figure 15-31). if the scl pin is sampled low before sda is allowed to float high, a bus collision occurs. this is another case of another master attempting to drive a data ? 0 ? (figure 15-32). figure 15-31: bus collision during a stop condition (case 1) figure 15-32: bus collision during a stop condition (case 2) sda scl bclif pen p sspif t brg t brg t brg sda asserted low sda sampled low after t brg , set bclif ? 0 ? ? 0 ? sda scl bclif pen p sspif t brg t brg t brg assert sda scl goes low before sda goes high, set bclif ? 0 ? ? 0 ?
PIC18F6390/6490/8390/8490 ds39629b-page 196 preliminary ? 2004 microchip technology inc. table 15-4: registers associated with i 2 c operation name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir1 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if 61 pie1 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie 61 ipr1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip 61 trisc portc data direction register 62 sspbuf synchronous serial port receive buffer/transmit register 60 sspadd synchronous serial port receive buffer/transmit register 60 sspcon1 wcol sspov sspen ckp sspm3 sspm2 sspm1 sspm0 60 sspcon2 gcen ackstat ackdt acken rcen pen rsen sen 60 sspstat smp cke d/a p s r/w ua bf 60 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used by the mssp in spi mode.
? 2004 microchip technology inc. preliminary ds39629b-page 197 PIC18F6390/6490/8390/8490 16.0 enhanced universal synchronous asynchronous receiver transmitter (eusart) PIC18F6390/6490/8390/8490 devices have three serial i/o modules: the mssp module, discussed in the previous chapter and two universal synchronous asynchronous receiver transmitter (usart) mod- ules. (generically, the usart is also known as a serial communications interface or sci.) the usart can be configured as a full-duplex asynchronous system that can communicate with peripheral devices, such as crt terminals and personal computers. it can also be configured as a half-duplex synchronous system that can communicate with peripheral devices, such as a/d or d/a integrated circuits, serial eeproms, etc. there are two distinct implementations of the usart module in these devices: the enhanced usart (eusart) discussed here and the addressable usart discussed in the next chapter. for this device family, usart1 always refers to the eusart, while usart2 is always the ausart. the eusart and ausart modules implement the same core features for serial communications; their basic operation is essentially the same. the eusart module provides additional features, including auto- matic baud rate detection and calibration, automatic wake-up on sync break reception and 12-bit break character transmit. these features make it ideally suited for use in local interconnect network bus (lin bus) systems. the eusart can be configured in the following modes: asynchronous (full-duplex) with: - auto-wake-up on character reception - auto-baud calibration - 12-bit break character transmission synchronous ? master (half-duplex) with selectable clock polarity synchronous ? slave (half-duplex) with selectable clock polarity the pins of the eusart are multiplexed with the func- tions of portc (rc6/tx1/ck1 and rc7/rx1/dt1). in order to configure these pins as an eusart: bit spen (rcsta1<7>) must be set (= 1 ) bit trisc<7> must be set (= 1 ) bit trisc<6> must be set (= 1 ) the operation of the enhanced usart module is controlled through three registers: transmit status and control register 1 (txsta1) receive status and control register 1 (rcsta1) baud rate control register 1 (baudcon1) the registers are described in register 16-1, register 16-2 and register 16-3. note: the usart control will automatically reconfigure the pin from input to output as needed.
PIC18F6390/6490/8390/8490 ds39629b-page 198 preliminary ? 2004 microchip technology inc. register 16-1: txsta1: eusart transmit status and control register r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r-1 r/w-0 csrc tx9 txen (1) sync sendb brgh trmt tx9d bit 7 bit 0 bit 7 csrc: clock source select bit asynchronous mode: don?t care. synchronous mode: 1 = master mode (clock generated internally from brg) 0 = slave mode (clock from external source) bit 6 tx9: 9-bit transmit enable bit 1 = selects 9-bit transmission 0 = selects 8-bit transmission bit 5 txen: transmit enable bit (1) 1 = transmit enabled 0 = transmit disabled note 1: sren/cren overrides txen in sync mode. bit 4 sync: ausart mode select bit 1 = synchronous mode 0 = asynchronous mode bit 3 sendb: send break character bit asynchronous mode: 1 = send sync break on next transmission (cleared by hardware upon completion) 0 = sync break transmission completed synchronous mode: don?t care. bit 2 brgh: high baud rate select bit asynchronous mode: 1 = high speed 0 = low speed synchronous mode: unused in this mode. bit 1 trmt: transmit shift register status bit 1 = tsr empty 0 = tsr full bit 0 tx9d: 9th bit of transmit data can be address/data bit or a parity bit. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
? 2004 microchip technology inc. preliminary ds39629b-page 199 PIC18F6390/6490/8390/8490 register 16-2: rcsta1: eusart receive status and control register r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r-0 r-0 r-x spen rx9 sren cren adden ferr oerr rx9d bit 7 bit 0 bit 7 spen: serial port enable bit 1 = serial port enabled (configures rx/dt and tx/ck pins as serial port pins) 0 = serial port disabled (held in reset) bit 6 rx9: 9-bit receive enable bit 1 = selects 9-bit reception 0 = selects 8-bit reception bit 5 sren: single receive enable bit asynchronous mode : don?t care. synchronous mode ? master: 1 = enables single receive 0 = disables single receive this bit is cleared after reception is complete. synchronous mode ? slave: don?t care. bit 4 cren: continuous receive enable bit asynchronous mode: 1 = enables receiver 0 = disables receiver synchronous mode: 1 = enables continuous receive until enable bit cren is cleared (cren overrides sren) 0 = disables continuous receive bit 3 adden: address detect enable bit asynchronous mode 9-bit (rx9 = 1 ) : 1 = enables address detection, enables interrupt and loads the receive buffer when rsr<8> is set 0 = disables address detection, all bytes are received and ninth bit can be used as parity bit asynchronous mode 9-bit (rx9 = 0 ) : don?t care. bit 2 ferr: framing error bit 1 = framing error (can be updated by reading rcreg register and receiving next valid byte) 0 = no framing error bit 1 oerr: overrun error bit 1 = overrun error (can be cleared by clearing bit cren) 0 = no overrun error bit 0 rx9d: 9th bit of received data this can be address/data bit or a parity bit and must be calculated by user firmware. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 200 preliminary ? 2004 microchip technology inc. register 16-3: baudcon1: baud rate control regi ster 1 r/w-0 r-1 u-0 r/w-0 r/w-0 u-0 r/w-0 r/w-0 abdovf rcidl ? sckp brg16 ? wue abden bit 7 bit 0 bit 7 abdovf : auto-baud acquisition rollover status bit 1 = a brg rollover has occurred during auto-baud rate detect mode (must be cleared in software) 0 = no brg rollover has occurred bit 6 rcidl : receive operation idle status bit 1 = receive operation is idle 0 = receive operation is active bit 5 unimplemented: read as ? 0 ? bit 4 sckp : synchronous clock polarity select bit asynchronous mode: unused in this mode. synchronous mode: 1 = idle state for clock (ck) is a high level 0 = idle state for clock (ck) is a low level bit 3 brg16: 16-bit baud rate register enable bit 1 = 16-bit baud rate generator ? spbrgh1 and spbrg1 0 = 8-bit baud rate generator ? spbrg1 only (compatible mode), spbrgh1 value ignored bit 2 unimplemented: read as ? 0 ? bit 1 wue: wake-up enable bit asynchronous mode: 1 = eusart will continue to sample the rx pin ? interrupt generated on falling edge; bit cleared in hardware on following rising edge 0 = rx pin not monitored or rising edge detected synchronous mode: unused in this mode. bit 0 abden : auto-baud detect enable bit asynchronous mode: 1 = enable baud rate measurement on the next character. requires reception of a sync field (55h); cleared in hardware upon completion. 0 = baud rate measurement disabled or completed synchronous mode: unused in this mode. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
? 2004 microchip technology inc. preliminary ds39629b-page 201 PIC18F6390/6490/8390/8490 16.1 eusart baud rate generator (brg) the brg is a dedicated, 8-bit or 16-bit generator that supports both the asynchronous and synchronous modes of the eusart. by default, the brg operates in 8-bit mode; setting the brg16 bit (baudcon1<3>) selects 16-bit mode. the spbrgh1:spbrg1 register pair controls the period of a free running timer. in asynchronous mode, bits brgh (txsta1<2>) and brg16 (baudcon1<3>) also control the baud rate. in synchronous mode, brgh is ignored. table 16-1 shows the formula for computa- tion of the baud rate for different eusart modes that only apply in master mode (internally generated clock). given the desired baud rate and f osc , the nearest integer value for the spbrgh1:spbrg1 registers can be calculated using the formulas in table 16-1. from this, the error in baud rate can be determined. an exam- ple calculation is shown in example 16-1. typical baud rates and error values for the various asynchronous modes are shown in table 16-2. it may be advanta- geous to use the high baud rate (brgh = 1 ) or the 16-bit brg to reduce the baud rate error, or achieve a slow baud rate for a fast oscillator frequency. writing a new value to the spbrgh1:spbrg1 regis- ters causes the brg timer to be reset (or cleared). this ensures the brg does not wait for a timer overflow before outputting the new baud rate. 16.1.1 operation in power managed modes the device clock is used to generate the desired baud rate. when one of the power managed modes is entered, the new clock source may be operating at a different frequency. this may require an adjustment to the value in the spbrg1 register pair. 16.1.2 sampling the data on the rx1 pin is sampled three times by a majority detect circuit to determine if a high or a low level is present at the rx1 pin. table 16-1: baud rate formulas example 16-1: calculating baud rate error table 16-2: registers associated with the baud rate generator configuration bits brg/eusart mode baud rate formula sync brg16 brgh 000 8-bit/asynchronous f osc /[64 (n + 1)] 001 8-bit/asynchronous f osc /[16 (n + 1)] 010 16-bit/asynchronous 011 16-bit/asynchronous f osc /[4 (n + 1)] 10x 8-bit/synchronous 11x 16-bit/synchronous legend: x = don?t care, n = value of spbrgh1:spbrg1 register pair name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page txsta1 csrc tx9 txen sync sendb brgh trmt tx9d 61 rcsta1 spen rx9 sren cren adden ferr oerr rx9d 61 baudcon1 abdovf rcidl ? sckp brg16 ? wue abden 62 spbrgh1 eusart1 baud rate generator register high byte 62 spbrg1 eusart1 baud rate generator register low byte 61 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used by the brg. for a device with f osc of 16 mhz, desired baud rate of 9600, asynchronous mode, 8-bit brg: desired baud rate = f osc /(64 ([spbrgh1:spbrg1] + 1)) solving for spbrgh1:spbrg1: x = ((f osc /desired baud rate)/64) ? 1 = ((16000000/9600)/64) ? 1 = [25.042] = 25 calculated baud rate = 16000000/(64 (25 + 1)) = 9615 error = (calculated baud rate ? desi red baud rate)/desired baud rate = (9615 ? 9600)/9600 = 0.16%
PIC18F6390/6490/8390/8490 ds39629b-page 202 preliminary ? 2004 microchip technology inc. table 16-3: baud rates for asynchronous modes baud rate (k) sync = 0 , brgh = 0 , brg16 = 0 f osc = 40.000 mhz f osc = 20.000 mhz f osc = 10.000 mhz f osc = 8.000 mhz actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) 0.3???????????? 1.2 ? ? ? 1.221 1.73 255 1.202 0.16 129 1201 -0.16 103 2.4 2.441 1.73 255 2.404 0.16 129 2.404 0.16 64 2403 -0.16 51 9.6 9.615 0.16 64 9.766 1.73 31 9.766 1.73 15 9615 -0.16 12 19.2 19.531 1.73 31 19.531 1.73 15 19.531 1.73 7 ? ? ? 57.6 56.818 -1.36 10 62.500 8.51 4 52.083 -9.58 2 ? ? ? 115.2 125.000 8.51 4 104.167 -9.58 2 78.125 -32.18 1 ? ? ? baud rate (k) sync = 0 , brgh = 0 , brg16 = 0 f osc = 4.000 mhz f osc = 2.000 mhz f osc = 1.000 mhz actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) 0.3 0.300 0.16 207 300 -0.16 103 300 -0.16 51 1.2 1.202 0.16 51 1201 -0.16 25 1201 -0.16 12 2.4 2.404 0.16 25 2403 -0.16 12 ? ? ? 9.6 8.929 -6.99 6 ? ? ? ? ? ? 19.2 20.833 8.51 2 ? ? ? ? ? ? 57.6 62.500 8.51 0 ? ? ? ? ? ? 115.2 62.500 -45.75 0 ? ? ? ? ? ? baud rate (k) sync = 0 , brgh = 1 , brg16 = 0 f osc = 40.000 mhz f osc = 20.000 mhz f osc = 10.000 mhz f osc = 8.000 mhz actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) 0.3???????????? 1.2???????????? 2.4 ? ? ? ? ? ? 2.441 1.73 255 2403 -0.16 207 9.6 9.766 1.73 255 9.615 0.16 129 9.615 0.16 64 9615 -0.16 51 19.2 19.231 0.16 129 19.231 0.16 64 19.531 1.73 31 19230 -0.16 25 57.6 58.140 0.94 42 56.818 -1.36 21 56.818 -1.36 10 55555 3.55 8 115.2 113.636 -1.36 21 113.636 -1.36 10 125.000 8.51 4 ? ? ? baud rate (k) sync = 0 , brgh = 1 , brg16 = 0 f osc = 4.000 mhz f osc = 2.000 mhz f osc = 1.000 mhz actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) 0.3 ? ? ? ? ? ? 300 -0.16 207 1.2 1.202 0.16 207 1201 -0.16 103 1201 -0.16 51 2.4 2.404 0.16 103 2403 -0.16 51 2403 -0.16 25 9.6 9.615 0.16 25 9615 -0.16 12 ? ? ? 19.2 19.231 0.16 12 ? ? ? ? ? ? 57.6 62.500 8.51 3 ? ? ? ? ? ? 115.2 125.000 8.51 1 ? ? ? ? ? ?
? 2004 microchip technology inc. preliminary ds39629b-page 203 PIC18F6390/6490/8390/8490 baud rate (k) sync = 0 , brgh = 0 , brg16 = 1 f osc = 40.000 mhz f osc = 20.000 mhz f osc = 10.000 mhz f osc = 8.000 mhz actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) 0.3 0.300 0.00 8332 0.300 0.02 4165 0.300 0.02 2082 300 -0.04 1665 1.2 1.200 0.02 2082 1.200 -0.03 1041 1.200 -0.03 520 1201 -0.16 415 2.4 2.402 0.06 1040 2.399 -0.03 520 2.404 0.16 259 2403 -0.16 207 9.6 9.615 0.16 259 9.615 0.16 129 9.615 0.16 64 9615 -0.16 51 19.2 19.231 0.16 129 19.231 0.16 64 19.531 1.73 31 19230 -0.16 25 57.6 58.140 0.94 42 56.818 -1.36 21 56.818 -1.36 10 55555 3.55 8 115.2 113.636 -1.36 21 113.636 -1.36 10 125.000 8.51 4 ? ? ? baud rate (k) sync = 0 , brgh = 0 , brg16 = 1 f osc = 4.000 mhz f osc = 2.000 mhz f osc = 1.000 mhz actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) 0.3 0.300 0.04 832 300 -0.16 415 300 -0.16 207 1.2 1.202 0.16 207 1201 -0.16 103 1201 -0.16 51 2.4 2.404 0.16 103 2403 -0.16 51 2403 -0.16 25 9.6 9.615 0.16 25 9615 -0.16 12 ? ? ? 19.2 19.231 0.16 12 ? ? ? ? ? ? 57.6 62.500 8.51 3 ? ? ? ? ? ? 115.2 125.000 8.51 1 ? ? ? ? ? ? baud rate (k) sync = 0 , brgh = 1 , brg16 = 1 or sync = 1 , brg16 = 1 f osc = 40.000 mhz f osc = 20.000 mhz f osc = 10.000 mhz f osc = 8.000 mhz actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) 0.3 0.300 0.00 33332 0.300 0.00 16665 0.300 0.00 8332 300 -0.01 6665 1.2 1.200 0.00 8332 1.200 0.02 4165 1.200 0.02 2082 1200 -0.04 1665 2.4 2.400 0.02 4165 2.400 0.02 2082 2.402 0.06 1040 2400 -0.04 832 9.6 9.606 0.06 1040 9.596 -0.03 520 9.615 0.16 259 9615 -0.16 207 19.2 19.193 -0.03 520 19.231 0.16 259 19.231 0.16 129 19230 -0.16 103 57.6 57.803 0.35 172 57.471 -0.22 86 58.140 0.94 42 57142 0.79 34 115.2 114.943 -0.22 86 116.279 0.94 42 113.636 -1.36 21 117647 -2.12 16 baud rate (k) sync = 0 , brgh = 1 , brg16 = 1 or sync = 1 , brg16 = 1 f osc = 4.000 mhz f osc = 2.000 mhz f osc = 1.000 mhz actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) 0.3 0.300 0.01 3332 300 -0.04 1665 300 -0.04 832 1.2 1.200 0.04 832 1201 -0.16 415 1201 -0.16 207 2.4 2.404 0.16 415 2403 -0.16 207 2403 -0.16 103 9.6 9.615 0.16 103 9615 -0.16 51 9615 -0.16 25 19.2 19.231 0.16 51 19230 -0.16 25 19230 -0.16 12 57.6 58.824 2.12 16 55555 3.55 8 ? ? ? 115.2 111.111 -3.55 8 ? ? ? ? ? ? table 16-3: baud rates for asynchronous modes (continued)
PIC18F6390/6490/8390/8490 ds39629b-page 204 preliminary ? 2004 microchip technology inc. 16.1.3 auto-baud rate detect the enhanced usart module supports the automatic detection and calibration of baud rate. this feature is active only in asynchronous mode and while the wue bit is clear. the automatic baud rate measurement sequence (figure 16-1) begins whenever a start bit is received and the abden bit is set. the calculation is self-averaging. in the auto-baud rate detect (abd) mode, the clock to the brg is reversed. rather than the brg clocking the incoming rx1 signal, the rx1 signal is timing the brg. in abd mode, the internal baud rate generator is used as a counter to time the bit period of the incoming serial byte stream. once the abden bit is set, the state machine will clear the brg and look for a start bit. the auto-baud rate detect must receive a byte with the value, 55h (ascii ?u?, which is also the lin bus sync character), in order to calculate the proper bit rate. the measurement is taken over both a low and a high bit time in order to minimize any effects caused by asymmetry of the incoming signal. after a start bit, the spbrg1 begins counting up, using the preselected clock source on the first rising edge of rx1. after eight bits on the rx1 pin or the fifth rising edge, an accumulated value totalling the proper brg period is left in the spbrgh1:spbrg1 register pair. once the 5th edge is seen (this should correspond to the stop bit), the abden bit is automatically cleared. if a rollover of the brg occurs (an overflow from ffffh to 0000h), the event is trapped by the abdovf status bit (baudcon1<7>). it is set in hardware by brg rollovers and can be set or cleared by the user in software. abd mode remains active after rollover events and the abden bit remains set (figure 16-2). while calibrating the baud rate period, the brg regis- ters are clocked at 1/8th the preconfigured clock rate. note that the brg clock will be configured by the brg16 and brgh bits. independent of the brg16 bit setting, both the spbrg1 and spbrgh1 will be used as a 16-bit counter. this allows the user to verify that no carry occurred for 8-bit modes by checking for 00h in the spbrgh1 register. refer to table 16-4 for counter clock rates to the brg. while the abd sequence takes place, the eusart state machine is held in idle. the rc1if interrupt is set once the fifth rising edge on rx1 is detected. the value in the rcreg1 needs to be read to clear the rc1if interrupt. the contents of rcreg1 should be discarded. table 16-4: brg counter clock rates 16.1.3.1 abd and eusart transmission since the brg clock is reversed during abd acquisi- tion, the eusart transmitter cannot be used during abd. this means that whenever the abden bit is set, txreg1 cannot be written to. users should also ensure that abden does not become set during a transmit sequence. failing to do this may result in unpredictable eusart operation. note 1: if the wue bit is set with the abden bit, auto-baud rate detection will occur on the byte following the break character. 2: it is up to the user to determine that the incoming character baud rate is within the range of the selected brg clock source. some combinations of oscillator frequency and eusart baud rates are not possible due to bit error rates. overall system timing and communication baud rates must be taken into consideration when using the auto-baud rate detection feature. brg16 brgh brg counter clock 00 f osc /512 01 f osc /128 10 f osc /128 11 f osc /32 note: during the abd sequence, spbrg1 and spbrgh1 are both used as a 16-bit counter, independent of the brg16 setting.
? 2004 microchip technology inc. preliminary ds39629b-page 205 PIC18F6390/6490/8390/8490 figure 16-1: automatic baud rate calculation figure 16-2: brg overflow sequence brg value rx1 pin abden bit rc1if bit bit 0 bit 1 (interrupt) read rcreg1 brg clock start auto-cleared set by user xxxxh 0000h edge #1 bit 2 bit 3 edge #2 bit 4 bit 5 edge #3 bit 6 bit 7 edge #4 stop bit edge #5 001ch note: the abd sequence requires the eusart module to be configured in asynchronous mode and wue = 0 . spbrg1 xxxxh 1ch spbrgh1 xxxxh 00h start bit 0 xxxxh 0000h 0000h ffffh brg clock abden bit rx1 pin abdovf bit brg value
PIC18F6390/6490/8390/8490 ds39629b-page 206 preliminary ? 2004 microchip technology inc. 16.2 eusart asynchronous mode the asynchronous mode of operation is selected by clearing the sync bit (txsta1<4>). in this mode, the eusart uses standard non-return-to-zero (nrz) for- mat (one start bit, eight or nine data bits and one stop bit). the most common data format is 8 bits. an on-chip dedicated 8-bit/16-bit baud rate generator can be used to derive standard baud rate frequencies from the oscillator. the eusart transmits and receives the lsb first. the eusart?s transmitter and receiver are functionally independent, but use the same data format and baud rate. the baud rate generator produces a clock, either x16 or x64 of the bit shift rate depending on the brgh and brg16 bits (txsta1<2> and baudcon1<3>). parity is not supported by the hardware but can be implemented in software and stored as the 9th data bit. when operating in asynchronous mode, the eusart module consists of the following important elements: baud rate generator sampling circuit asynchronous transmitter asynchronous receiver auto-wake-up on sync break character 12-bit break character transmit auto-baud rate detection 16.2.1 eusart asynchronous transmitter the eusart transmitter block diagram is shown in figure 16-3. the heart of the transmitter is the transmit (serial) shift register (tsr). the shift register obtains its data from the read/write transmit buffer register, txreg1. the txreg1 register is loaded with data in software. the tsr register is not loaded until the stop bit has been transmitted from the previous load. as soon as the stop bit is transmitted, the tsr is loaded with new data from the txreg1 register (if available). once the txreg1 register transfers the data to the tsr register (occurs in one t cy ), the txreg1 register is empty and the tx1if flag bit (pir1<4>) is set. this interrupt can be enabled or disabled by setting or clear- ing the interrupt enable bit, tx1ie (pie1<4>). tx1if will be set regardless of the state of tx1ie; it cannot be cleared in software. tx1if is also not cleared immedi- ately upon loading txreg1, but becomes valid in the second instruction cycle following the load instruction. polling tx1if immediately following a load of txreg1 will return invalid results. while tx1if indicates the status of the txreg1 regis- ter, another bit, trmt (txsta1<1>), shows the status of the tsr register. trmt is a read-only bit which is set when the tsr register is empty. no interrupt logic is tied to this bit so the user has to poll this bit in order to determine if the tsr register is empty. to set up an asynchronous transmission: 1. initialize the spbrgh1:spbrg1 registers for the appropriate baud rate. set or clear the brgh and brg16 bits, as required, to achieve the desired baud rate. 2. enable the asynchronous serial port by clearing bit sync and setting bit spen. 3. if interrupts are desired, set enable bit tx1ie. 4. if 9-bit transmission is desired, set transmit bit tx9; can be used as address/data bit. 5. enable the transmission by setting bit txen, which will also set bit tx1if. 6. if 9-bit transmission is selected, the ninth bit should be loaded in bit tx9d. 7. load data to the txreg1 register (starts transmission). 8. if using interrupts, ensure that the gie and peie bits in the intcon register (intcon<7:6>) are set. figure 16-3: eusart transmit block diagram note 1: the tsr register is not mapped in data memory so it is not available to the user. 2: flag bit tx1if is set when enable bit txen is set. tx1if tx1ie interrupt txen baud rate clk spbrg1 baud rate generator tx9d msb lsb data bus txreg1 register tsr register (8) 0 tx9 trmt spen tx1 pin pin buffer and control 8 ? ? ? spbrgh1 brg16
? 2004 microchip technology inc. preliminary ds39629b-page 207 PIC18F6390/6490/8390/8490 figure 16-4: asynchronous transmission figure 16-5: asynchronous transmission (back to back) table 16-5: registers associated with asynchronous transmission word 1 word 1 transmit shift reg start bit bit 0 bit 1 bit 7/8 write to txreg1 brg output (shift clock) tx1 (pin) tx1if bit (transmit buffer reg. empty flag) trmt bit (transmit shift reg. empty flag) 1 t cy word 1 stop bit transmit shift reg. write to txreg1 brg output (shift clock) tx1 (pin) tx1if bit (interrupt reg. flag) trmt bit (transmit shift reg. empty flag) word 1 word 2 word 1 word 2 stop bit start bit transmit shift reg. word 1 word 2 bit 0 bit 1 bit 7/8 bit 0 note: this timing diagram shows two consecutive transmissions. 1 t cy 1 t cy start bit name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir1 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if 61 pie1 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie 61 ipr1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip 61 rcsta1 spen rx9 sren cren adden ferr oerr rx9d 61 txreg1 eusart1 transmit register 61 txsta1 csrc tx9 txen sync sendb brgh trmt tx9d 61 baudcon1 abdovf rcidl ? sckp brg16 ? wue abden 62 spbrgh1 eusart1 baud rate generator register high byte 62 spbrg1 eusart1 baud rate generator register low byte 61 legend: ? = unimplemented locations read as ? 0 ?. shaded cells are not used for asynchronous transmission.
PIC18F6390/6490/8390/8490 ds39629b-page 208 preliminary ? 2004 microchip technology inc. 16.2.2 eusart asynchronous receiver the receiver block diagram is shown in figure 16-6. the data is received on the rx1 pin and drives the data recovery block. the data recovery block is actually a high-speed shifter operating at x16 times the baud rate, whereas the main receive serial shifter operates at the bit rate or at f osc . this mode would typically be used in rs-232 systems. to set up an asynchronous reception: 1. initialize the spbrgh1:spbrg1 registers for the appropriate baud rate. set or clear the brgh and brg16 bits, as required, to achieve the desired baud rate. 2. enable the asynchronous serial port by clearing bit sync and setting bit spen. 3. if interrupts are desired, set enable bit rc1ie. 4. if 9-bit reception is desired, set bit rx9. 5. enable the reception by setting bit cren. 6. flag bit rc1if will be set when reception is complete and an interrupt will be generated if enable bit rc1ie was set. 7. read the rcsta1 register to get the 9th bit (if enabled) and determine if any error occurred during reception. 8. read the 8-bit received data by reading the rcreg1 register. 9. if any error occurred, clear the error by clearing enable bit cren. 10. if using interrupts, ensure that the gie and peie bits in the intcon register (intcon<7:6>) are set. 16.2.3 setting up 9-bit mode with address detect this mode would typically be used in rs-485 systems. to set up an asynchronous reception with address detect enable: 1. initialize the spbrgh1:spbrg1 registers for the appropriate baud rate. set or clear the brgh and brg16 bits, as required, to achieve the desired baud rate. 2. enable the asynchronous serial port by clearing the sync bit and setting the spen bit. 3. if interrupts are required, set the rcen bit and select the desired priority level with the rc1ip bit. 4. set the rx9 bit to enable 9-bit reception. 5. set the adden bit to enable address detect. 6. enable reception by setting the cren bit. 7. the rc1if bit will be set when reception is complete. the interrupt will be acknowledged if the rc1ie and gie bits are set. 8. read the rcsta1 register to determine if any error occurred during reception, as well as read bit 9 of data (if applicable). 9. read rcreg1 to determine if the device is being addressed. 10. if any error occurred, clear the cren bit. 11. if the device has been addressed, clear the adden bit to allow all received data into the receive buffer and interrupt the cpu. figure 16-6: eusart receiv e block diagram x64 baud rate clk baud rate generator rx1 pin buffer and control spen data recovery cren oerr ferr rsr register msb lsb rx9d rcreg1 register fifo interrupt rc1if rc1ie data bus 8 64 16 or stop start (8) 7 1 0 rx9 ? ? ? spbrg1 spbrgh1 brg16 or 4
? 2004 microchip technology inc. preliminary ds39629b-page 209 PIC18F6390/6490/8390/8490 figure 16-7: asynchronous reception table 16-6: registers associated with asynchronous reception start bit bit 7/8 bit 1 bit 0 bit 7/8 bit 0 stop bit start bit start bit bit 7/8 stop bit rx1 (pin) rcv buffer reg rcv shift reg read rcv buffer reg rcreg1 rc1if (interrupt flag) oerr bit cren bit word 1 rcreg1 word 2 rcreg1 stop bit note: this timing diagram shows three words appearing on the rx1 input. the rcreg1 (receive buffer register) is read after the third word causing the oerr (overrun) bit to be set. name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir1 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if 61 pie1 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie 61 ipr1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip 61 rcsta1 spen rx9 sren cren adden ferr oerr rx9d 61 rcreg1 eusart1 receive register 61 txsta1 csrc tx9 txen sync sendb brgh trmt tx9d 61 baudcon1 abdovf rcidl ? sckp brg16 ? wue abden 62 spbrgh1 eusart1 baud rate generator register high byte 62 spbrg1 eusart1 baud rate generator register low byte 61 legend: ? = unimplemented locations read as ? 0 ?. shaded cells are not used for asynchronous reception.
PIC18F6390/6490/8390/8490 ds39629b-page 210 preliminary ? 2004 microchip technology inc. 16.2.4 auto-wake-up on sync break character during sleep mode, all clocks to the eusart are suspended. because of this, the baud rate generator is inactive and a proper byte reception cannot be per- formed. the auto-wake-up feature allows the controller to wake-up, due to activity on the rx1/dt1 line, while the eusart is operating in asynchronous mode. the auto-wake-up feature is enabled by setting the wue bit (baudcon<1>). once set, the typical receive sequence on rx1/dt1 is disabled and the eusart remains in an idle state, monitoring for a wake-up event independent of the cpu mode. a wake-up event consists of a high-to-low transition on the rx1/dt1 line. (this coincides with the start of a sync break or a wake-up signal character for the lin protocol.) following a wake-up event, the module generates an rc1if interrupt. the interrupt is generated synchro- nously to the q clocks in normal operating modes (figure 16-8) and asynchronously, if the device is in sleep mode (figure 16-9). the interrupt condition is cleared by reading the rcreg1 register. the wue bit is automatically cleared once a low-to-high transition is observed on the rx1 line following the wake-up event. at this point, the eusart module is in idle mode and returns to normal operation. this signals to the user that the sync break event is over. 16.2.4.1 special considerations using auto-wake-up since auto-wake-up functions by sensing rising edge transitions on rx1/dt1, information with any state changes before the stop bit may signal a false end-of-character and cause data or framing errors. therefore, to work properly, the initial character in the transmission must be all ? 0 ?s. this can be 00h (8 bytes) for standard rs-232 devices, or 000h (12 bits) for lin bus. oscillator start-up time must also be considered, especially in applications using oscillators with longer start-up intervals (i.e., xt or hs mode). the sync break (or wake-up signal) character must be of sufficient length and be followed by a sufficient interval to allow enough time for the selected oscillator to start and provide proper initialization of the eusart. 16.2.4.2 special considerations using the wue bit the timing of wue and rc1if events may cause some confusion when it comes to determining the validity of received data. as noted, setting the wue bit places the eusart in an idle mode. the wake-up event causes a receive interrupt by setting the rc1if bit. the wue bit is cleared after this when a rising edge is seen on rx1/dt1. the interrupt condition is then cleared by reading the rcreg1 register. ordinarily, the data in rcreg1 will be dummy data and should be discarded. the fact that the wue bit has been cleared (or is still set) and the rc1if flag is set should not be used as an indicator of the integrity of the data in rcreg1. users should consider implementing a parallel method in firmware to verify received data integrity. to assure that no actual data is lost, check the rcidl bit to verify that a receive operation is not in process. if a receive operation is not occurring, the wue bit may then be set just prior to entering the sleep mode. figure 16-8: auto-wake-up bit (wue) timings during normal operation figure 16-9: auto-wake-up bit (wue) timings during sleep q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 osc1 wue bit rx1/dt1 line rc1if cleared due to user read of rcreg1 note: the eusart remains in idle while the wue bit is set. bit set by user auto-cleared q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 osc1 wue bit rx1/dt1 line rc1if cleared due to user read of rcreg1 sleep command executed note 1: if the wake-up event requires long oscillator warm-up time, the auto-clear of the wue bit can occur while the stposc signal is still active. this sequence should not depend on the presence of q clocks. 2: the eusart remains in idle while the wue bit is set. sleep ends auto-cleared note 1 bit set by user
? 2004 microchip technology inc. preliminary ds39629b-page 211 PIC18F6390/6490/8390/8490 16.2.5 break character sequence the enhanced usart module has the capability of sending the special break character sequences that are required by the lin bus sta ndard. the break character transmit consists of a start bit, followed by twelve ? 0 ? bits and a stop bit. the frame break character is sent whenever the sendb and txen bits (txsta<3> and txsta<5>) are set while the transmit shift register is loaded with data. note that the value of data written to txreg1 will be ignored and all ? 0 ?s will be transmitted. the sendb bit is automatically reset by hardware after the corresponding stop bit is sent. this allows the user to preload the transmit fifo with the next transmit byte following the break character (typically, the sync character in the lin specification). note that the data value written to the txreg1 for the break character is ignored. the write simply serves the purpose of initiating the proper sequence. the trmt bit indicates when the transmit operation is active or idle, just as it does during normal transmis- sion. see figure 16-10 for the timing of the break character sequence. 16.2.5.1 break and sync transmit sequence the following sequence will send a message frame header made up of a break, followed by an auto-baud sync byte. this sequence is typical of a lin bus master. 1. configure the eusart for the desired mode. 2. set the txen and sendb bits to set up the break character. 3. load the txreg1 with a dummy character to initiate transmission (the value is ignored). 4. write ?55h? to txreg1 to load the sync character into the transmit fifo buffer. 5. after the break has been sent, the sendb bit is reset by hardware. the sync character now transmits in the preconfigured mode. when the txreg1 becomes empty, as indicated by the tx1if, the next data byte can be written to txreg1. 16.2.6 receiving a break character the enhanced usart module can receive a break character in two ways. the first method forces configuration of the baud rate at a frequency of 9/13 the typical speed. this allows for the stop bit transition to be at the correct sampling location (13 bits for break versus start bit and 8 data bits for typical data). the second method uses the auto-wake-up feature described in section 16.2.4 ?auto-wake-up on sync break character? . by enabling this feature, the eusart will sample the next two transitions on rx1/dt1, cause an rc1if interrupt and receive the next data byte followed by another interrupt. note that following a break character, the user will typically want to enable the auto-baud rate detect feature. for both methods, the user can set the abd bit once the tx1if interrupt is observed. figure 16-10: send break character sequence write to txreg1 brg output (shift clock) start bit bit 0 bit 1 bit 11 stop bit break tx1if bit (transmit buffer reg. empty flag) tx1 (pin) trmt bit (transmit shift reg. empty flag) sendb (transmit shift reg. empty flag) sendb sampled here auto-cleared dummy write
PIC18F6390/6490/8390/8490 ds39629b-page 212 preliminary ? 2004 microchip technology inc. 16.3 eusart synchronous master mode the synchronous master mode is entered by setting the csrc bit (txsta<7>). in this mode, the data is transmitted in a half-duplex manner (i.e., transmission and reception do not occur at the same time). when transmitting data, the reception is inhibited and vice versa. synchronous mode is entered by setting bit sync (txsta<4>). in addition, enable bit, spen (rcsta1<7>), is set in order to configure the tx1 and rx1 pins to ck1 (clock) and dt1 (data) lines, respectively. the master mode indicates that the processor trans- mits the master clock on the ck1 line. clock polarity is selected with the sckp bit (baudcon<4>); setting sckp sets the idle state on ck1 as high, while clearing the bit sets the idle state as low. this option is provided to support microwire devices with this module. 16.3.1 eusart synchronous master transmission the eusart transmitter block diagram is shown in figure 16-3. the heart of the transmitter is the transmit (serial) shift register (tsr). the shift register obtains its data from the read/write transmit buffer register, txreg1. the txreg1 register is loaded with data in software. the tsr register is not loaded until the last bit has been transmitted from the previous load. as soon as the last bit is transmitted, the tsr is loaded with new data from the txreg1 (if available). once the txreg1 register transfers the data to the tsr register (occurs in one t cycle ), the txreg1 is empty and the tx1if flag bit (pir1<4>) is set. the interrupt can be enabled or disabled by setting or clear- ing the interrupt enable bit, tx1ie (pie1<4>). tx1if is set regardless of the state of enable bit tx1ie; it cannot be cleared in software. it will reset only when new data is loaded into the txreg1 register. while flag bit tx1if indicates the status of the txreg1 register, another bit, trmt (txsta<1>), shows the status of the tsr register. trmt is a read-only bit which is set when the tsr is empty. no interrupt logic is tied to this bit so the user has to poll this bit in order to deter- mine if the tsr register is empty. the tsr is not mapped in data memory so it is not available to the user. to set up a synchronous master transmission: 1. initialize the spbrgh1:spbrg1 registers for the appropriate baud rate. set or clear the brg16 bit, as required, to achieve the desired baud rate. 2. enable the synchronous master serial port by setting bits sync, spen and csrc. 3. if interrupts are desired, set enable bit tx1ie. 4. if 9-bit transmission is desired, set bit tx9. 5. enable the transmission by setting bit txen. 6. if 9-bit transmission is selected, the ninth bit should be loaded in bit tx9d. 7. start transmission by loading data to the txreg1 register. 8. if using interrupts, ensure that the gie and peie bits in the intcon register (intcon<7:6>) are set. figure 16-11: synchronous transmission bit 0 bit 1 bit 7 word 1 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1q2 q3 q4 q1 q2 q3 q4 bit 2 bit 0 bit 1 bit 7 rc7/rx1/dt1 rc6/tx1/ck1 pin write to txreg1 reg tx1if bit (interrupt flag) txen bit ? 1 ? ? 1 ? word 2 trmt bit write word 1 write word 2 note: sync master mode, spbrg1 = 0 , continuous transmission of two 8-bit words. pin rc6/tx1/ck1 pin (sckp = 0 ) (sckp = 1 )
? 2004 microchip technology inc. preliminary ds39629b-page 213 PIC18F6390/6490/8390/8490 figure 16-12: synchronous transmis sion (through txen) table 16-7: registers associated with synchronous master transmission rc7/rx1/dt1 pin rc6/tx1/ck1 pin write to txreg1 reg tx1if bit trmt bit bit 0 bit 1 bit 2 bit 6 bit 7 txen bit name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir1 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if 61 pie1 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie 61 ipr1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip 61 rcsta1 spen rx9 sren cren adden ferr oerr rx9d 61 txreg1 eusart1 transmit register 61 txsta1 csrc tx9 txen sync sendb brgh trmt tx9d 61 baudcon1 abdovf rcidl ?sckpbrg16 ? wue abden 62 spbrgh1 eusart1 baud rate generator register high byte 62 spbrg1 eusart1 baud rate generator register low byte 61 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used for synchronous master transmission.
PIC18F6390/6490/8390/8490 ds39629b-page 214 preliminary ? 2004 microchip technology inc. 16.3.2 eusart synchronous master reception once synchronous mode is selected, reception is enabled by setting either the single receive enable bit, sren (rcsta1<5>), or the continuous receive enable bit, cren (rcsta1<4>). data is sampled on the rx1 pin on the falling edge of the clock. if enable bit sren is set, only a single word is received. if enable bit cren is set, the reception is continuous until cren is cleared. if both bits are set, then cren takes precedence. to set up a synchronous master reception: 1. initialize the spbrgh1:spbrg1 registers for the appropriate baud rate. set or clear the brg16 bit, as required, to achieve the desired baud rate. 2. enable the synchronous master serial port by setting bits sync, spen and csrc. 3. ensure bits cren and sren are clear. 4. if interrupts are desired, set enable bit rc1ie. 5. if 9-bit reception is desired, set bit rx9. 6. if a single reception is required, set bit sren. for continuous reception, set bit cren. 7. interrupt flag bit rc1if will be set when reception is complete and an interrupt will be generated if the enable bit rc1ie was set. 8. read the rcsta1 register to get the 9th bit (if enabled) and determine if any error occurred during reception. 9. read the 8-bit received data by reading the rcreg1 register. 10. if any error occurred, clear the error by clearing bit cren. 11. if using interrupts, ensure that the gie and peie bits in the intcon register (intcon<7:6>) are set. figure 16-13: synchronous reception (master mode, sren) table 16-8: registers associated with synchronous master reception name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir1 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if 61 pie1 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie 61 ipr1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip 61 rcsta1 spen rx9 sren cren adden ferr oerr rx9d 61 rcreg1 eusart1 receive register 61 txsta1 csrc tx9 txen sync sendb brgh trmt tx9d 61 baudcon1 abdovf rcidl ? sckp brg16 ? wue abden 62 spbrgh1 eusart1 baud rate generator register high byte 62 spbrg1 eusart1 baud rate generator register low byte 61 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used for synchronous master reception. cren bit rc7/rx1/dt1 rc6/tx1/ck1 pin write to sren bit sren bit rc1if bit (interrupt) read rcreg1 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q2 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 ? 0 ? bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 ? 0 ? q1 q2 q3 q4 note: timing diagram demonstrates sync master mode with bit sren = 1 and bit brgh = 0 . rc6/tx1/ck1 pin pin (sckp = 0 ) (sckp = 1 )
? 2004 microchip technology inc. preliminary ds39629b-page 215 PIC18F6390/6490/8390/8490 16.4 eusart synchronous slave mode synchronous slave mode is entered by clearing bit csrc (txsta<7>). this mode differs from the synchronous master mode in that the shift clock is supplied externally at the ck1 pin (instead of being supplied internally in master mode). this allows the device to transfer or receive data while in any low-power mode. 16.4.1 eusart synchronous slave transmit the operation of the synchronous master and slave modes are identical except in the case of the sleep mode. if two words are written to the txreg1 and then the sleep instruction is executed, the following will occur: a) the first word will immediately transfer to the tsr register and transmit. b) the second word will remain in the txreg1 register. c) flag bit tx1if will not be set. d) when the first word has been shifted out of tsr, the txreg1 register will transfer the second word to the tsr and flag bit tx1if will now be set. e) if enable bit tx1ie is set, the interrupt will wake the chip from sleep. if the global interrupt is enabled, the program will branch to the interrupt vector. to set up a synchronous slave transmission: 1. enable the synchronous slave serial port by setting bits sync and spen and clearing bit csrc. 2. clear bits cren and sren. 3. if interrupts are desired, set enable bit tx1ie. 4. if 9-bit transmission is desired, set bit tx9. 5. enable the transmission by setting enable bit txen. 6. if 9-bit transmission is selected, the ninth bit should be loaded in bit tx9d. 7. start transmission by loading data to the txreg1x register. 8. if using interrupts, ensure that the gie and peie bits in the intcon register (intcon<7:6>) are set. table 16-9: registers associated with synchronous slave transmission name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir1 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if 61 pie1 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie 61 ipr1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip 61 rcsta1 spen rx9 sren cren adden ferr oerr rx9d 61 txreg1 eusart1 transmit register 61 txsta1 csrc tx9 txen sync sendb brgh trmt tx9d 61 baudcon1 abdovf rcidl ? sckp brg16 ? wue abden 62 spbrgh1 eusart1 baud rate generator register high byte 62 spbrg1 eusart1 baud rate generator register low byte 61 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used for synchronous slave transmission.
PIC18F6390/6490/8390/8490 ds39629b-page 216 preliminary ? 2004 microchip technology inc. 16.4.2 eusart synchronous slave reception the operation of the synchronous master and slave modes is identical except in the case of sleep or any idle mode and bit sren, which is a ?don?t care? in slave mode. if receive is enabled by setting the cren bit prior to entering sleep or any idle mode, then a word may be received while in this low-power mode. once the word is received, the rsr register will transfer the data to the rcreg1 register; if the rc1ie enable bit is set, the interrupt generated will wake the chip from the low-power mode. if the global interrupt is enabled, the program will branch to the interrupt vector. to set up a synchronous slave reception: 1. enable the synchronous master serial port by setting bits sync and spen and clearing bit csrc. 2. if interrupts are desired, set enable bit rc1ie. 3. if 9-bit reception is desired, set bit rx9. 4. to enable reception, set enable bit cren. 5. flag bit rc1if will be set when reception is complete. an interrupt will be generated if enable bit rc1ie was set. 6. read the rcsta1 register to get the 9th bit (if enabled) and determine if any error occurred during reception. 7. read the 8-bit received data by reading the rcreg1 register. 8. if any error occurred, clear the error by clearing bit cren. 9. if using interrupts, ensure that the gie and peie bits in the intcon register (intcon<7:6>) are set. table 16-10: registers associated with synchronous slave reception name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir1 ? adif rc1if tx1if sspif ccp1if tmr2if tmr1if 61 pie1 ? adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie 61 ipr1 ? adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip 61 rcsta1 spen rx9 sren cren adden ferr oerr rx9d 61 rcreg1 eusart1 receive register 61 txsta1 csrc tx9 txen sync sendb brgh trmt tx9d 61 baudcon1 abdovf rcidl ?sckpbrg16 ? wue abden 62 spbrgh1 eusart1 baud rate generator register high byte 62 spbrg1 eusart1 baud rate generator register low byte 61 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used for synchronous slave reception.
? 2004 microchip technology inc. preliminary ds39629b-page 217 PIC18F6390/6490/8390/8490 17.0 addressable universal synchronous asynchronous receiver transmitter (ausart) the addressable universal synchronous asynchro- nous receiver transmitter (ausart) module is very similar in function to the enhanced usart module, discussed in the previous chapter. it is provided as an additional channel for serial communication with external devices, for those situations that do not require auto-baud detection or lin bus support. the ausart can be configured in the following modes: asynchronous (full-duplex) synchronous ? master (half-duplex) synchronous ? slave (half-duplex) the pins of the ausart module are multiplexed with the functions of portg (rg1/tx2/ck2/seg29 and rg2/rx2/dt2/seg28, respectively). in order to configure these pins as an ausart: bit spen (rcsta2<7>) must be set (= 1 ) bit trisg<2> must be set (= 1 ) bit trisg<1> must be cleared (= 0 ) for asynchronous and synchronous master modes bit trisg<1> must be set (= 1 ) for synchronous slave mode the operation of the addressable usart module is controlled through two registers, txsta2 and rxsta2. these are detailed in register 17-1 and register 17-2 respectively. note: the ausart control will automatically reconfigure the pin from input to output as needed.
PIC18F6390/6490/8390/8490 ds39629b-page 218 preliminary ? 2004 microchip technology inc. register 17-1: txsta2: ausart transmit status and control register r/w-0 r/w-0 r/w-0 r/w-0 u-0 r/w-0 r-1 r/w-0 csrc tx9 txen (1) sync ?brghtrmttx9d bit 7 bit 0 bit 7 csrc: clock source select bit asynchronous mode: don?t care. synchronous mode: 1 = master mode (clock generated internally from brg) 0 = slave mode (clock from external source) bit 6 tx9: 9-bit transmit enable bit 1 = selects 9-bit transmission 0 = selects 8-bit transmission bit 5 txen: transmit enable bit (1) 1 = transmit enabled 0 = transmit disabled note 1: sren/cren overrides txen in sync mode. bit 4 sync: ausart mode select bit 1 = synchronous mode 0 = asynchronous mode bit 3 unimplemented: read as ? 0 ? bit 2 brgh: high baud rate select bit asynchronous mode: 1 = high speed 0 = low speed synchronous mode: unused in this mode. bit 1 trmt: transmit shift register status bit 1 = tsr empty 0 = tsr full bit 0 tx9d: 9th bit of transmit data can be address/data bit or a parity bit. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
? 2004 microchip technology inc. preliminary ds39629b-page 219 PIC18F6390/6490/8390/8490 register 17-2: rcsta2: ausart receive status and control register r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r-0 r-0 r-x spen rx9 sren cren adden ferr oerr rx9d bit 7 bit 0 bit 7 spen: serial port enable bit 1 = serial port enabled (configures rx/dt and tx/ck pins as serial port pins) 0 = serial port disabled (held in reset) bit 6 rx9: 9-bit receive enable bit 1 = selects 9-bit reception 0 = selects 8-bit reception bit 5 sren: single receive enable bit asynchronous mode : don?t care. synchronous mode ? master: 1 = enables single receive 0 = disables single receive this bit is cleared after reception is complete. synchronous mode ? slave: don?t care. bit 4 cren: continuous receive enable bit asynchronous mode: 1 = enables receiver 0 = disables receiver synchronous mode: 1 = enables continuous receive until enable bit cren is cleared (cren overrides sren) 0 = disables continuous receive bit 3 adden: address detect enable bit asynchronous mode 9-bit (rx9 = 1 ) : 1 = enables address detection, enables interrupt and loads the receive buffer when rsr<8> is set 0 = disables address detection, all bytes are received and ninth bit can be used as parity bit asynchronous mode 9-bit (rx9 = 0 ) : don?t care. bit 2 ferr: framing error bit 1 = framing error (can be updated by reading rcreg register and receiving next valid byte) 0 = no framing error bit 1 oerr: overrun error bit 1 = overrun error (can be cleared by clearing bit cren) 0 = no overrun error bit 0 rx9d: 9th bit of received data this can be address/data bit or a parity bit and must be calculated by user firmware. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 220 preliminary ? 2004 microchip technology inc. 17.1 ausart baud rate generator (brg) the brg is a dedicated 8-bit generator that supports both the asynchronous and synchronous modes of the ausart. the spbrg2 register controls the period of a free running timer. in asynchronous mode, bit brgh (txsta<2>) also controls the baud rate. in synchro- nous mode, brgh is ignored. table 17-1 shows the formula for computation of the baud rate for different ausart modes, which only apply in master mode (internally generated clock). given the desired baud rate and f osc , the nearest integer value for the spbrg2 register can be calcu- lated using the formulas in table 17-1. from this, the error in baud rate can be determined. an example calculation is shown in example 17-1. typical baud rates and error values for the various asynchronous modes are shown in table 17-2. it may be advanta- geous to use the high baud rate (brgh = 1 ) to reduce the baud rate error, or achieve a slow baud rate for a fast oscillator frequency. writing a new value to the spbrg2 register causes the brg timer to be reset (or cleared). this ensures the brg does not wait for a timer overflow before outputting the new baud rate. 17.1.1 operation in power managed modes the device clock is used to generate the desired baud rate. when one of the power managed modes is entered, the new clock source may be operating at a different frequency. this may require an adjustment to the value in the spbrg2 register. 17.1.2 sampling the data on the rx2 pin is sampled three times by a majority detect circuit to determine if a high or a low level is present at the rx2 pin. table 17-1: baud rate formulas example 17-1: calculating baud rate error table 17-2: registers associated with the baud rate generator configuration bits brg/ausart mode baud rate formula sync brgh 00 asynchronous f osc /[64 (n + 1)] 01 asynchronous f osc /[16 (n + 1)] 1x synchronous f osc /[4 (n + 1)] legend: x = don?t care, n = value of spbrg2 register name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page txsta2 csrc tx9 txen sync ?brgh trmt tx9d 63 rcsta2 spen rx9 sren cren adden ferr oerr rx9d 63 spbrg2 ausart2 baud rate generator register 63 legend: shaded cells are not used by the brg. for a device with f osc of 16 mhz, desired baud rate of 9600, asynchronous mode, brgh = 0 : desired baud rate = f osc /(64 ([spbrg2] + 1)) solving for spbrg2: x = ((f osc /desired baud rate)/64) ? 1 = ((16000000/9600)/64) ? 1 = [25.042] = 25 calculated baud rate = 16000000/(64 (25 + 1)) = 9615 error = (calculated baud rate ? desi red baud rate)/desired baud rate = (9615 ? 9600)/9600 = 0.16%
? 2004 microchip technology inc. preliminary ds39629b-page 221 PIC18F6390/6490/8390/8490 table 17-3: baud rates for asynchronous modes brgh = 0 f osc = 40.000 mhz f osc = 20.000 mhz f osc = 10.000 mhz f osc = 8.000 mhz baud rate (k) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) 0.3???????????? 1.2 ? ? ? 1.221 1.73 255 1.202 0.16 129 1201 -0.16 103 2.4 2.441 1.73 255 2.404 0.16 129 2.404 0.16 64 2403 -0.16 51 9.6 9.615 0.16 64 9.766 1.73 31 9.766 1.73 15 9615 -0.16 12 19.2 19.531 1.73 31 19.531 1.73 15 19.531 1.73 7 ? ? ? 57.6 56.818 -1.36 10 62.500 8.51 4 52.083 -9.58 2 ? ? ? 115.2 125.000 8.51 4 104.167 -9.58 2 78.125 -32.18 1 ? ? ? brgh = 0 f osc = 4.000 mhz f osc = 2.000 mhz f osc = 1.000 mhz baud rate (k) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) 0.3 0.300 0.16 207 300 -0.16 103 300 -0.16 51 1.2 1.202 0.16 51 1201 -0.16 25 1201 -0.16 12 2.4 2.404 0.16 25 2403 -0.16 12 ? ? ? 9.6 8.929 -6.99 6 ? ? ? ? ? ? 19.2 20.833 8.51 2 ? ? ? ? ? ? 57.6 62.500 8.51 0 ? ? ? ? ? ? 115.2 62.500 -45.75 0 ? ? ? ? ? ? baud rate (k) brgh = 1 f osc = 40.000 mhz f osc = 20.000 mhz f osc = 10.000 mhz f osc = 8.000 mhz actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) 0.3???????????? 1.2???????????? 2.4 ? ? ? ? ? ? 2.441 1.73 255 2403 -0.16 207 9.6 9.766 1.73 255 9.615 0.16 129 9.615 0.16 64 9615 -0.16 51 19.2 19.231 0.16 129 19.231 0.16 64 19.531 1.73 31 19230 -0.16 25 57.6 58.140 0.94 42 56.818 -1.36 21 56.818 -1.36 10 55555 3.55 8 115.2 113.636 -1.36 21 113.636 -1.36 10 125.000 8.51 4 ? ? ? baud rate (k) brgh = 1 f osc = 4.000 mhz f osc = 2.000 mhz f osc = 1.000 mhz actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) actual rate (k) % error spbrg value (decimal) 0.3 ? ? ? ? ? ? 300 -0.16 207 1.2 1.202 0.16 207 1201 -0.16 103 1201 -0.16 51 2.4 2.404 0.16 103 2403 -0.16 51 2403 -0.16 25 9.6 9.615 0.16 25 9615 -0.16 12 ? ? ? 19.2 19.231 0.16 12 ? ? ? ? ? ? 57.6 62.500 8.51 3 ? ? ? ? ? ? 115.2 125.000 8.51 1 ? ? ? ? ? ?
PIC18F6390/6490/8390/8490 ds39629b-page 222 preliminary ? 2004 microchip technology inc. 17.2 ausart asynchronous mode the asynchronous mode of operation is selected by clearing the sync bit (txsta2<4>). in this mode, the ausart uses standard non-return-to-zero (nrz) format (one start bit, eight or nine data bits and one stop bit). the most common data format is 8 bits. an on-chip dedicated 8-bit baud rate generator can be used to derive standard baud rate frequencies from the oscillator. the ausart transmits and receives the lsb first. the ausart?s transmitter and receiver are functionally independent but use the same data format and baud rate. the baud rate generator produces a clock, either x16 or x64 of the bit shift rate, depending on the brgh bit (txsta2<2>). parity is not supported by the hardware but can be implemented in software and stored as the 9th data bit. when operating in asynchronous mode, the ausart module consists of the following important elements: baud rate generator sampling circuit asynchronous transmitter asynchronous receiver 17.2.1 ausart asynchronous transmitter the ausart transmitter block diagram is shown in figure 17-1. the heart of the transmitter is the transmit (serial) shift register (tsr). the shift register obtains its data from the read/write transmit buffer register, txreg2. the txreg2 register is loaded with data in software. the tsr register is not loaded until the stop bit has been transmitted from the previous load. as soon as the stop bit is transmitted, the tsr is loaded with new data from the txreg2 register (if available). once the txreg2 register transfers the data to the tsr register (occurs in one t cy ), the txreg2 register is empty and the tx2if flag bit (pir3<4>) is set. this interrupt can be enabled or disabled by setting or clearing the interrupt enable bit, tx2ie (pie3<4>). tx2if will be set regardless of the state of tx2ie; it cannot be cleared in software. tx2if is also not cleared immediately upon loading txreg2, but becomes valid in the second instruction cycle following the load instruction. polling tx2if immediately following a load of txreg2 will return invalid results. while tx2if indicates the status of the txreg2 register, another bit, trmt (txsta2<1>), shows the status of the tsr register. trmt is a read-only bit which is set when the tsr register is empty. no inter- rupt logic is tied to this bit so the user has to poll this bit in order to determine if the tsr register is empty. to set up an asynchronous transmission: 1. initialize the spbrg2 register for the appropriate baud rate. set or clear the brgh bit, as required, to achieve the desired baud rate. 2. enable the asynchronous serial port by clearing bit sync and setting bit spen. 3. if interrupts are desired, set enable bit tx2ie. 4. if 9-bit transmission is desired, set transmit bit tx9. can be used as address/data bit. 5. enable the transmission by setting bit txen, which will also set bit tx2if. 6. if 9-bit transmission is selected, the ninth bit should be loaded in bit tx9d. 7. load data to the txreg2 register (starts transmission). 8. if using interrupts, ensure that the gie and peie bits in the intcon register (intcon<7:6>) are set. figure 17-1: ausart transmit block diagram note 1: the tsr register is not mapped in data memory so it is not available to the user. 2: flag bit tx2if is set when enable bit txen is set. tx2if tx2ie interrupt txen baud rate clk spbrg2 baud rate generator tx9d msb lsb data bus txreg2 register tsr register (8) 0 tx9 trmt spen tx2 pin pin buffer and control 8 ? ? ?
? 2004 microchip technology inc. preliminary ds39629b-page 223 PIC18F6390/6490/8390/8490 figure 17-2: asynchronous transmission figure 17-3: asynchronous transmission (back to back) table 17-4: registers associated with asynchronous transmission word 1 word 1 transmit shift reg start bit bit 0 bit 1 bit 7/8 write to txreg2 brg output (shift clock) tx2 (pin) tx2if bit (transmit buffer reg. empty flag) trmt bit (transmit shift reg. empty flag) 1 t cy word 1 stop bit transmit shift reg. write to txreg2 brg output (shift clock) tx2 (pin) tx2if bit (interrupt reg. flag) trmt bit (transmit shift reg. empty flag) word 1 word 2 word 1 word 2 stop bit start bit transmit shift reg. word 1 word 2 bit 0 bit 1 bit 7/8 bit 0 note: this timing diagram shows two consecutive transmissions. 1 t cy 1 t cy start bit name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir3 ? lcdif rc2if tx2if ? ? ? ?61 pie3 ? lcdie rc2ie tx2ie ? ? ? ?61 ipr3 ? lcdip rc2ip tx2ip ? ? ? ?61 rcsta2 spen rx9 sren cren adden ferr oerr rx9d 63 txreg2 ausart2 transmit register 63 txsta2 csrc tx9 txen sync ? brgh trmt tx9d 63 spbrg2 ausart2 baud rate generator register 63 legend: ? = unimplemented locations read as ? 0 ?. shaded cells are not used for asynchronous transmission.
PIC18F6390/6490/8390/8490 ds39629b-page 224 preliminary ? 2004 microchip technology inc. 17.2.2 ausart asynchronous receiver the receiver block diagram is shown in figure 17-4. the data is received on the rx2 pin and drives the data recovery block. the data recovery block is actually a high-speed shifter operating at x16 times the baud rate, whereas the main receive serial shifter operates at the bit rate or at f osc . this mode would typically be used in rs-232 systems. to set up an asynchronous reception: 1. initialize the spbrg2 register for the appropriate baud rate. set or clear the brgh bit, as required, to achieve the desired baud rate. 2. enable the asynchronous serial port by clearing bit sync and setting bit spen. 3. if interrupts are desired, set enable bit rc2ie. 4. if 9-bit reception is desired, set bit rx9. 5. enable the reception by setting bit cren. 6. flag bit rc2if will be set when reception is complete and an interrupt will be generated if enable bit rc2ie was set. 7. read the rcsta2 register to get the 9th bit (if enabled) and determine if any error occurred during reception. 8. read the 8-bit received data by reading the rcreg2 register. 9. if any error occurred, clear the error by clearing enable bit cren. 10. if using interrupts, ensure that the gie and peie bits in the intcon register (intcon<7:6>) are set. 17.2.3 setting up 9-bit mode with address detect this mode would typically be used in rs-485 systems. to set up an asynchronous reception with address detect enable: 1. initialize the spbrg2 register for the appropriate baud rate. set or clear the brgh and brg16 bits, as required, to achieve the desired baud rate. 2. enable the asynchronous serial port by clearing the sync bit and setting the spen bit. 3. if interrupts are required, set the rcen bit and select the desired priority level with the rc2ip bit. 4. set the rx9 bit to enable 9-bit reception. 5. set the adden bit to enable address detect. 6. enable reception by setting the cren bit. 7. the rc2if bit will be set when reception is complete. the interrupt will be acknowledged if the rc2ie and gie bits are set. 8. read the rcsta2 register to determine if any error occurred during reception, as well as read bit 9 of data (if applicable). 9. read rcreg2 to determine if the device is being addressed. 10. if any error occurred, clear the cren bit. 11. if the device has been addressed, clear the adden bit to allow all received data into the receive buffer and interrupt the cpu. figure 17-4: ausart recei ve block diagram x64 baud rate clk baud rate generator rx2 pin buffer and control spen data recovery cren oerr ferr rsr register msb lsb rx9d rcreg2 register fifo interrupt rc2if rc2ie data bus 8 64 16 or stop start (8) 7 1 0 rx9 ? ? ? spbrg2 or 4
? 2004 microchip technology inc. preliminary ds39629b-page 225 PIC18F6390/6490/8390/8490 figure 17-5: asynchronous reception table 17-5: registers associated with asynchronous reception start bit bit 7/8 bit 1 bit 0 bit 7/8 bit 0 stop bit start bit start bit bit 7/8 stop bit rx2 (pin) rcv buffer reg rcv shift reg read rcv buffer reg rcreg2 rc2if (interrupt flag) oerr bit cren word 1 rcreg2 word 2 rcreg2 stop bit note: this timing diagram shows three words appearing on the rx2 input. the rcreg2 (receive buffer register) is read after the thir d word causing the oerr (overrun) bit to be set. name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir3 ? lcdif rc2if tx2if ? ? ? ?61 pie3 ? lcdie rc2ie tx2ie ? ? ? ?61 ipr3 ? lcdip rc2ip tx2ip ? ? ? ?61 rcsta2 spen rx9 sren cren adden ferr oerr rx9d 63 rcreg2 ausart2 receive register 63 txsta2 csrc tx9 txen sync ?brgh trmt tx9d 63 spbrg2 ausart2 baud rate generator register 63 legend: ? = unimplemented locations read as ? 0 ?. shaded cells are not used for asynchronous reception.
PIC18F6390/6490/8390/8490 ds39629b-page 226 preliminary ? 2004 microchip technology inc. 17.3 ausart synchronous master mode the synchronous master mode is entered by setting the csrc bit (txsta2<7>). in this mode, the data is transmitted in a half-duplex manner (i.e., transmission and reception do not occur at the same time). when transmitting data, the reception is inhibited and vice versa. synchronous mode is entered by setting bit sync (txsta2<4>). in addition, enable bit spen (rcsta2<7>) is set in order to configure the tx2 and rx2 pins to ck2 (clock) and dt2 (data) lines, respectively. the master mode indicates that the processor transmits the master clock on the ck2 line. 17.3.1 ausart synchronous master transmission the ausart transmitter block diagram is shown in figure 17-1. the heart of the transmitter is the transmit (serial) shift register (tsr). the shift register obtains its data from the read/write transmit buffer register, txreg2. the txreg2 register is loaded with data in software. the tsr register is not loaded until the last bit has been transmitted from the previous load. as soon as the last bit is transmitted, the tsr is loaded with new data from the txreg2 (if available). once the txreg2 register transfers the data to the tsr register (occurs in one t cycle ), the txreg2 is empty and the tx2if flag bit (pir3<4>) is set. the interrupt can be enabled or disabled by setting or clear- ing the interrupt enable bit tx2ie (pie3<4>). tx2if is set regardless of the state of enable bit tx2ie; it cannot be cleared in software. it will reset only when new data is loaded into the txreg2 register. while flag bit tx2if indicates the status of the txreg2 register, another bit, trmt (txsta2<1>), shows the status of the tsr register. trmt is a read-only bit which is set when the tsr is empty. no interrupt logic is tied to this bit so the user has to poll this bit in order to deter- mine if the tsr register is empty. the tsr is not mapped in data memory so it is not available to the user. to set up a synchronous master transmission: 1. initialize the spbrg2 register for the appropriate baud rate. 2. enable the synchronous master serial port by setting bits sync, spen and csrc. 3. if interrupts are desired, set enable bit tx2ie. 4. if 9-bit transmission is desired, set bit tx9. 5. enable the transmission by setting bit txen. 6. if 9-bit transmission is selected, the ninth bit should be loaded in bit tx9d. 7. start transmission by loading data to the txreg2 register. 8. if using interrupts, ensure that the gie and peie bits in the intcon register (intcon<7:6>) are set. figure 17-6: synchronous transmission bit 0 bit 1 bit 7 word 1 q1 q2 q3q4 q1 q2 q3 q4 q1 q2 q3 q4 q1q2 q3 q4 q1 q2 q3 q4 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 bit 2 bit 0 bit 1 bit 7 rx2/dt2 pin tx2/ck2 pin write to txreg2 reg tx2if bit (interrupt flag) txen bit ? 1 ? ? 1 ? word 2 trmt bit write word 1 write word 2 note: sync master mode, spbrg2 = 0 , continuous transmission of two 8-bit words.
? 2004 microchip technology inc. preliminary ds39629b-page 227 PIC18F6390/6490/8390/8490 figure 17-7: synchronous transmissi on (through txen) table 17-6: registers associated with synchronous master transmission rx2/dt2 pin tx2/ck2 pin write to txreg22 reg tx2if bit trmt bit bit 0 bit 1 bit 2 bit 6 bit 7 txen bit name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir3 ? lcdif rc2if tx2if ? ? ? ?61 pie3 ? lcdie rc2ie tx2ie ? ? ? ?61 ipr3 ? lcdip rc2ip tx2ip ? ? ? ?61 rcsta2 spen rx9 sren cren adden ferr oerr rx9d 63 txreg2 ausart2 transmit register 63 txsta2 csrc tx9 txen sync ? brgh trmt tx9d 63 spbrg2 ausart2 baud rate generator register 63 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used for synchronous master transmission.
PIC18F6390/6490/8390/8490 ds39629b-page 228 preliminary ? 2004 microchip technology inc. 17.3.2 ausart synchronous master reception once synchronous mode is selected, reception is enabled by setting either the single receive enable bit, sren (rcsta2<5>), or the continuous receive enable bit, cren (rcsta2<4>). data is sampled on the rx2 pin on the falling edge of the clock. if enable bit sren is set, only a single word is received. if enable bit cren is set, the reception is continuous until cren is cleared. if both bits are set, then cren takes precedence. to set up a synchronous master reception: 1. initialize the spbrg2 register for the appropriate baud rate. 2. enable the synchronous master serial port by setting bits sync, spen and csrc. 3. ensure bits cren and sren are clear. 4. if interrupts are desired, set enable bit rc2ie. 5. if 9-bit reception is desired, set bit rx9. 6. if a single reception is required, set bit sren. for continuous reception, set bit cren. 7. interrupt flag bit, rc2if, will be set when recep- tion is complete and an interrupt will be generated if the enable bit rc2ie was set. 8. read the rcsta2 register to get the 9th bit (if enabled) and determine if any error occurred during reception. 9. read the 8-bit received data by reading the rcreg2 register. 10. if any error occurred, clear the error by clearing bit cren. 11. if using interrupts, ensure that the gie and peie bits in the intcon register (intcon<7:6>) are set. figure 17-8: synchronous reception (master mode, sren) table 17-7: registers associated with synchronous master reception name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir3 ? lcdif rc2if tx2if ? ? ? ?61 pie3 ? lcdie rc2ie tx2ie ? ? ? ?61 ipr3 ? lcdip rc2ip tx2ip ? ? ? ?61 rcsta2 spen rx9 sren cren adden ferr oerr rx9d 63 rcreg2 ausart2 receive register 63 txsta2 csrc tx9 txen sync ? brgh trmt tx9d 63 spbrg2 ausart2 baud rate generator register low byte 63 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used for synchronous master reception. cren bit rx2/dt2 pin tx2/ck2 pin write to bit sren sren bit rc2if bit (interrupt) read rcreg2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q2 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 q1 q2 q3 q4 ? 0 ? bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 ? 0 ? q1 q2 q3 q4 note: timing diagram demonstrates sync master mode with bit sren = 1 and bit brgh = 0 .
? 2004 microchip technology inc. preliminary ds39629b-page 229 PIC18F6390/6490/8390/8490 17.4 ausart synchronous slave mode synchronous slave mode is entered by clearing bit csrc (txsta2<7>). this mode differs from the synchronous master mode in that the shift clock is supplied externally at the ck2 pin (instead of being supplied internally in master mode). this allows the device to transfer or receive data while in any low-power mode. 17.4.1 ausart synchronous slave transmit the operation of the synchronous master and slave modes are identical except in the case of the sleep mode. if two words are written to the txreg2 and then the sleep instruction is executed, the following will occur: a) the first word will immediately transfer to the tsr register and transmit. b) the second word will remain in txreg2 register. c) flag bit tx2if will not be set. d) when the first word has been shifted out of tsr, the txreg2 register will transfer the second word to the tsr and flag bit tx2if will now be set. e) if enable bit tx2ie is set, the interrupt will wake the chip from sleep. if the global interrupt is enabled, the program will branch to the interrupt vector. to set up a synchronous slave transmission: 1. enable the synchronous slave serial port by setting bits sync and spen and clearing bit csrc. 2. clear bits cren and sren. 3. if interrupts are desired, set enable bit tx2ie. 4. if 9-bit transmission is desired, set bit tx9. 5. enable the transmission by setting enable bit txen. 6. if 9-bit transmission is selected, the ninth bit should be loaded in bit tx9d. 7. start transmission by loading data to the txreg2 register. 8. if using interrupts, ensure that the gie and peie bits in the intcon register (intcon<7:6>) are set. table 17-8: registers associated with synchronous slave transmission name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir3 ? lcdif rc2if tx2if ? ? ? ?61 pie3 ? lcdie rc2ie tx2ie ? ? ? ?61 ipr3 ? lcdip rc2ip tx2ip ? ? ? ?61 rcsta2 spen rx9 sren cren adden ferr oerr rx9d 63 txreg2 ausart2 transmit register 63 txsta2 csrc tx9 txen sync ? brgh trmt tx9d 63 spbrg2 ausart2 baud rate generator register low byte 63 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used for synchronous slave transmission.
PIC18F6390/6490/8390/8490 ds39629b-page 230 preliminary ? 2004 microchip technology inc. 17.4.2 ausart synchronous slave reception the operation of the synchronous master and slave modes is identical except in the case of sleep, or any idle mode and bit sren, which is a ?don?t care? in slave mode. if receive is enabled by setting the cren bit prior to entering sleep, or any idle mode, then a word may be received while in this low-power mode. once the word is received, the rsr register will transfer the data to the rcreg2 register; if the rc2ie enable bit is set, the interrupt generated will wake the chip from low-power mode. if the global interrupt is enabled, the program will branch to the interrupt vector. to set up a synchronous slave reception: 1. enable the synchronous master serial port by setting bits sync and spen and clearing bit csrc. 2. if interrupts are desired, set enable bit rc2ie. 3. if 9-bit reception is desired, set bit rx9. 4. to enable reception, set enable bit cren. 5. flag bit rc2if will be set when reception is complete. an interrupt will be generated if enable bit rc2ie was set. 6. read the rcsta2 register to get the 9th bit (if enabled) and determine if any error occurred during reception. 7. read the 8-bit received data by reading the rcreg2 register. 8. if any error occurred, clear the error by clearing bit cren. 9. if using interrupts, ensure that the gie and peie bits in the intcon register (intcon<7:6>) are set. table 17-9: registers associated with synchronous slave reception name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir3 ? lcdif rc2if tx2if ? ? ? ?61 pie3 ? lcdie rc2ie tx2ie ? ? ? ?61 ipr3 ? lcdip rc2ip tx2ip ? ? ? ?61 rcsta2 spen rx9 sren cren adden ferr oerr rx9d 63 rcreg2 ausart2 receive register 63 txsta2 csrc tx9 txen sync ? brgh trmt tx9d 63 spbrg2 ausart2 baud rate generator register low byte 63 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used for synchronous slave reception.
? 2004 microchip technology inc. preliminary ds39629b-page 231 PIC18F6390/6490/8390/8490 18.0 10-bit analog-to-digital converter (a/d) module the analog-to-digital (a/d) converter module has 12 inputs for the pic18f6x90/8x90 devices. this module allows conversion of an analog input signal to a corresponding 10-bit digital number. the module has five registers: a/d result high register (adresh) a/d result low register (adresl) a/d control register 0 (adcon0) a/d control register 1 (adcon1) a/d control register 2 (adcon2) the adcon0 register, shown in register 18-1, controls the operation of the a/d module. the adcon1 register, shown in register 18-2, configures the functions of the port pins. the adcon2 register, shown in register 18-3, configures the a/d clock source, programmed acquisition time and justification. register 18-1: adcon0: a/d control register 0 u-0 u-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 ? ? chs3 chs2 chs1 chs0 go/done adon bit 7 bit 0 bit 7-6 unimplemented: read as ? 0 ? bit 5-2 chs3:chs0: analog channel select bits 0000 = channel 0 (an0) 0001 = channel 1 (an1) 0010 = channel 2 (an2) 0011 = channel 3 (an3) 0100 = channel 4 (an4) 0101 = channel 5 (an5) 0110 = channel 6 (an6) 0111 = channel 7 (an7) 1000 = channel 8 (an8) 1001 = channel 9 (an9) 1010 = channel 10 (an10) 1011 = channel 11 (an11) 1100 = unimplemented (1) 1101 = unimplemented (1) 1110 = unimplemented (1) 1111 = unimplemented (1) note 1: performing a conversion on unimplemented channels will return a floating input measurement. bit 1 go/done : a/d conversion status bit when adon = 1 : 1 = a/d conversion in progress 0 = a/d idle bit 0 adon: a/d on bit 1 = a/d converter module is enabled 0 = a/d converter module is disabled legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 232 preliminary ? 2004 microchip technology inc. register 18-2: adcon1: a/d control register 1 u-0 u-0 r/w-0 r/w-0 r/w-q r/w-q r/w-q r/w-q ? ? vcfg1 vcfg0 pcfg3 pcfg2 pcfg1 pcfg0 bit 7 bit 0 bit 7-6 unimplemented: read as ? 0 ? bit 5 vcfg1: voltage reference configuration bit (v ref - source): 1 = v ref - (an2) 0 = av ss bit 4 vcfg0: voltage reference configuration bit (v ref + source): 1 = v ref + (an3) 0 = av dd bit 3-0 pcfg3:pcfg0: a/d port configuration control bits: legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown a = analog input d = digital i/o pcfg3: pcfg0 an11 an10 an9 an8 an7 an6 an5 an4 an3 an2 an1 an0 0000 a aaaaaaaaaaa 0001 a aaaaaaaaaaa 0010 a aaaaaaaaaaa 0011 a aaaaaaaaaaa 0100 d aaaaaaaaaaa 0101 d daaaaaaaaaa 0110 d ddaaaaaaaaa 0111 d dddaaaaaaaa 1000 d ddddaaaaaaa 1001 d dddddaaaaaa 1010 d ddddddaaaaa 1011 d dddddddaaaa 1100 d ddddddddaaa 1101 d dddddddddaa 1110 d dddddddddda 1111 d ddddddddddd
? 2004 microchip technology inc. preliminary ds39629b-page 233 PIC18F6390/6490/8390/8490 register 18-3: adcon2: a/d control register 2 r/w-0 u-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 adfm ? acqt2 acqt1 acqt0 adcs2 adcs1 adcs0 bit 7 bit 0 bit 7 adfm: a/d result format select bit 1 = right justified 0 = left justified bit 6 unimplemented: read as ? 0 ? bit 5-3 acqt2:acqt0: a/d acquisition time select bits 111 = 20 t ad 110 = 16 t ad 101 = 12 t ad 100 = 8 t ad 011 = 6 t ad 010 = 4 t ad 001 = 2 t ad 000 = 0 t ad (1) bit 2-0 adcs2:adcs0: a/d conversion clock select bits 111 = f rc (clock derived from a/d rc oscillator) (1) 110 = f osc /64 101 = f osc /16 100 = f osc /4 011 = f rc (clock derived from a/d rc oscillator) (1) 010 = f osc /32 001 = f osc /8 000 = f osc /2 note 1: if the a/d f rc clock source is selected, a delay of one t cy (instruction cycle) is added before the a/d clock starts. this allows the sleep instruction to be executed before starting a conversion. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 234 preliminary ? 2004 microchip technology inc. the analog reference voltage is software selectable to either the device?s positive and negative supply voltage (av dd and av ss ), or the voltage level on the ra3/an3/v ref +/seg17 and ra2/an2/v ref -/seg16 pins. the a/d converter has a unique feature of being able to operate while the device is in sleep mode. to oper- ate in sleep, the a/d conversion clock must be derived from the a/d?s internal rc oscillator. the output of the sample and hold is the input into the converter, which generates the result via successive approximation. a device reset forces all registers to their reset state. this forces the a/d module to be turned off and any conversion in progress is aborted. each port pin associated with the a/d converter can be configured as an analog input or as a digital i/o. the adresh and adresl registers contain the result of the a/d conversion. when the a/d conversion is com- plete, the result is loaded into the adresh/adresl registers, the go/done bit (adcon0 register) is cleared and the a/d interrupt flag bit, adif, is set. the block diagram of the a/d module is shown in figure 18-1. figure 18-1: a/d block diagram (input voltage) v ain v ref + reference voltage av dd vcfg1:vcfg0 chs3:chs0 an7 an6 an5 an4 an3 an2 an1 an0 0111 0110 0101 0100 0011 0010 0001 0000 10-bit converter v ref - av ss a/d an11 an10 an9 an8 1011 1010 1001 1000 note 1: i/o pins have diode protection to v dd and v ss . 0 x 1 x x 1 x 0
? 2004 microchip technology inc. preliminary ds39629b-page 235 PIC18F6390/6490/8390/8490 the value in the adresh:adresl registers is not modified for a power-on reset. the adresh:adresl registers will contain unknown data after a power-on reset. after the a/d module has been configured as desired, the selected channel must be acquired before the con- version is started. the analog input channels must have their corresponding tris bits selected as an input. to determine acquisition time, see section 18.1 ?a/d acquisition requirements? . after this acquisi- tion time has elapsed, the a/d conversion can be started. an acquisition time can be programmed to occur between setting the go/done bit and the actual start of the conversion. the following steps should be followed to perform an a/d conversion: 1. configure the a/d module: configure analog pins, voltage reference and digital i/o (adcon1) select a/d input channel (adcon0) select a/d acquisition time (adcon2) select a/d conversion clock (adcon2) turn on a/d module (adcon0) 2. configure a/d interrupt (if desired): clear adif bit set adie bit set gie bit 3. wait the required acquisition time (if required). 4. start conversion: set go/done bit (adcon0 register) 5. wait for a/d conversion to complete, by either: polling for the go/done bit to be cleared or waiting for the a/d interrupt 6. read a/d result registers (adresh:adresl); clear bit adif, if required. 7. for next conversion, go to step 1 or step 2, as required. the a/d conversion time per bit is defined as t ad . a minimum wait of 3 t ad is required before the next acquisition starts. figure 18-2: a/d transfer function figure 18-3: analog input model digital code output 3feh 003h 002h 001h 000h 0.5 lsb 1 lsb 1.5 lsb 2 lsb 2.5 lsb 1022 lsb 1022.5 lsb 3 lsb analog input voltage 3ffh 1023 lsb 1023.5 lsb v ain c pin rs anx 5 pf v t = 0.6v v t = 0.6v i leakage r ic 1k sampling switch ss r ss c hold = 25 pf v ss v dd 100 na legend: c pin v t i leakage r ic ss c hold = input capacitance = threshold voltage = leakage current at the pin due to = interconnect resistance = sampling switch = sample/hold capacitance (from dac) various junctions = sampling switch resistance r ss v dd 6v sampling switch 5v 4v 3v 2v 123 4 (k ? )
PIC18F6390/6490/8390/8490 ds39629b-page 236 preliminary ? 2004 microchip technology inc. 18.1 a/d acquisition requirements for the a/d converter to meet its specified accuracy, the charge holding capacitor (c hold ) must be allowed to fully charge to the input channel voltage level. the analog input model is shown in figure 18-3. the source impedance (r s ) and the internal sampling switch (r ss ) impedance directly affect the time required to charge the capacitor c hold . the sampling switch (r ss ) impedance varies over the device voltage (v dd ). the source impedance affects the offset voltage at the analog input (due to pin leakage current). the maximum recommended impedance for analog sources is 2.5 k ? . after the analog input channel is selected (changed), the channel must be sampled for at least the minimum acquisition time before starting a conversion. to calculate the minimum acquisition time, equation 18-1 may be used. this equation assumes that 1/2 lsb error is used (1024 steps for the a/d). the 1/2 lsb error is the maximum error allowed for the a/d to meet its specified resolution. example 18-3 shows the calculation of the minimum required acquisition time t acq . this calculation is based on the following application system assumptions: c hold = 25 pf rs = 2.5 k ? conversion error 1/2 lsb v dd =5v rss = 2 k ? temperature = 85 c (system max.) equation 18-1: acquisition time equation 18-2: a/d minimum charging time equation 18-3: calculating the minimum required acquisition time note: when the conversion is started, the holding capacitor is disconnected from the input pin. t acq = amplifier settling time + holding capacitor charging time + temperature coefficient =t amp + t c + t coff v hold = (v ref ? (v ref /2048)) (1 ? e (-t c /c hold (r ic + r ss + r s )) ) or t c = -(c hold )(r ic + r ss + r s ) ln(1/2048) t acq =t amp + t c + t coff t amp =0.2 s t coff = (temp ? 25 c)(0.02 s/ c) (50 c ? 25 c)(0.02 s/ c) 1.2 s temperature coefficient is only required for temperatures > 25 c. below 25 c, t coff = 0 ms. t c = -(c hold )(r ic + r ss + r s ) ln(1/2047) s -(25 pf) (1 k ? + 2 k ? + 2.5 k ? ) ln(0.0004883) s 5.03 s t acq =0.2 s + 5 s + 1.2 s 6.4 s
? 2004 microchip technology inc. preliminary ds39629b-page 237 PIC18F6390/6490/8390/8490 18.2 selecting and configuring automatic acquisition time the adcon2 register allows the user to select an acquisition time that occurs each time the go/done bit is set. when the go/done bit is set, sampling is stopped and a conversion begins. the user is responsible for ensur- ing the required acquisition time has passed between selecting the desired input channel and setting the go/done bit. this occurs when the acqt2:acqt0 bits (adcon2<5:3>) remain in their reset state (? 000 ?) and is compatible with devices that do not offer programmable acquisition times. if desired, the acqt bits can be set to select a programmable acquisition time for the a/d module. when the go/done bit is set, the a/d module contin- ues to sample the input for the selected acquisition time, then automatically begins a conversion. since the acquisition time is programmed, there may be no need to wait for an acquisition time between selecting a channel and setting the go/done bit. in either case, when the conversion is completed, the go/done bit is cleared, the adif flag is set and the a/d begins sampling the currently selected channel again. if an acquisition time is programmed, there is nothing to indicate if the acquisition time has ended or if the conversion has begun. 18.3 selecting the a/d conversion clock the a/d conversion time per bit is defined as t ad . the a/d conversion requires 11 t ad per 10-bit conversion. the source of the a/d conversion clock is software selectable. there are seven possible options for t ad : 2 t osc 4 t osc 8 t osc 16 t osc 32 t osc 64 t osc internal rc oscillator for correct a/d conversions, the a/d conversion clock (t ad ) must be as short as possible, but greater than the minimum t ad (approximately 2 s, see parameter 130 for more information). table 18-1 shows the resultant t ad times derived from the device operating frequencies and the a/d clock source selected. table 18-1: t ad vs. device operating frequencies ad clock source (t ad ) maximum device frequency operation adcs2:adcs0 pic18f6x10/8x10 pic18lf6x10/8x10 (4) 2 t osc 000 1.25 mhz 666 khz 4 t osc 100 2.50 mhz 1.33 mhz 8 t osc 001 5.00 mhz 2.66 mhz 16 t osc 101 10.0 mhz 5.33 mhz 32 t osc 010 20.0 mhz 10.65 mhz 64 t osc 110 40.0 mhz 21.33 mhz rc (3) x11 1.00 mhz (1) 1.00 mhz (2) note 1: the rc source has a typical t ad time of 4 s. 2: the rc source has a typical t ad time of 6 s. 3: for device frequencies above 1 mhz, the device must be in sleep for the entire conversion or the a/d accuracy may be out of specification. 4: low-power (pic18lfxxxx) devices only.
PIC18F6390/6490/8390/8490 ds39629b-page 238 preliminary ? 2004 microchip technology inc. 18.4 operation in power managed modes the selection of the automatic acquisition time and a/d conversion clock is determined in part by the clock source and frequency while in a power managed mode. if the a/d is expected to operate while the device is in a power managed mode, the acqt2:acqt0 and adcs2:adcs0 bits in adcon2 should be updated in accordance with the power managed mode clock that will be used. after the power managed mode is entered, an a/d acquisition or conversion may be started. once an acquisition or conversion is started, the device should continue to be clocked by the same power managed mode clock source until the conver- sion has been completed. if desired, the device may be placed into the corresponding power managed idle mode during the conversion. if the power managed mode clock frequency is less than 1 mhz, the a/d rc clock source should be selected. operation in the sleep mode requires the a/d f rc clock to be selected. if bits acqt2:acqt0 are set to ? 000 ? and a conversion is started, the conversion will be delayed one instruction cycle to allow execution of the sleep instruction and entry to sleep mode. the idlen and scs bits in the osccon register must have already been cleared prior to starting the conversion. 18.5 configuring analog port pins the adcon1, trisa and trisf registers all configure the a/d port pins. the port pins needed as analog inputs must have their corresponding tris bits set (input). if the tris bit is cleared (output), the digital output level (v oh or v ol ) will be converted. the a/d operation is independent of the state of the chs3:chs0 bits and the tris bits. note 1: when reading the port register, all pins configured as analog input channels will read as cleared (a low level). pins config- ured as digital inputs will convert an analog input. analog levels on a digitally configured input will be accurately converted. 2: analog levels on any pin defined as a digital input may cause the digital input buffer to consume current out of the device?s specification limits.
? 2004 microchip technology inc. preliminary ds39629b-page 239 PIC18F6390/6490/8390/8490 18.6 a/d conversions figure 18-4 shows the operation of the a/d converter after the go bit has been set and the acqt2:acqt0 bits are cleared. a conversion is started after the follow- ing instruction to allow entry into sleep mode before the conversion begins. figure 18-5 shows the operation of the a/d converter after the go bit has been set and the acqt2:acqt0 bits are set to ? 010 ? and selecting a 4 t ad acquisition time before the conversion starts. clearing the go/done bit during a conversion will abort the current conversion. the a/d result register pair will not be updated with the partially completed a/d conversion sample. this means the adresh:adresl registers will continue to contain the value of the last completed conversion (or the last value written to the adresh:adresl registers). after the a/d conversion is completed or aborted, a 2t ad wait is required before the next acquisition can be started. after this wait, acquisition on the selected channel is automatically started. 18.7 discharge the discharge phase is used to initialize the value of the capacitor array. the array is discharged before every sample. this feature helps to optimize the unity-gain amplifier as the circuit always needs to charge the capacitor array, rather than charge/discharge based on previous measure values. figure 18-4: a/d conversion t ad cycles (acqt<2:0> = 000 , t acq = 0 ) figure 18-5: a/d conversion t ad cycles (acqt<2:0> = 010 , t acq = 4 t ad ) note: the go/done bit should not be set in the same instruction that turns on the a/d. t ad 1 t ad 2 t ad 3 t ad 4 t ad 5 t ad 6 t ad 7 t ad 8 t ad 11 set go bit holding capacitor is disconnected from analog input (typically 100 ns) t ad 9 t ad 10 t cy - t ad adresh:adresl is loaded, go bit is cleared, adif bit is set, holding capacitor is connected to analog input. conversion starts b0 b9 b6 b5 b4 b3 b2 b1 b8 b7 on the following cycle: t ad 1 discharge 1 2 3 4 5 6 7 8 11 set go bit (holding capacitor is disconnected) 9 10 conversion starts 1 2 3 4 (holding capacitor continues acquiring input) t acqt cycles t ad cycles automatic acquisition time b0 b9 b6 b5 b4 b3 b2 b1 b8 b7 adresh:adresl is loaded, go bit is cleared, adif bit is set, holding capacitor is connected to analog input. on the following cycle: t ad 1 discharge
PIC18F6390/6490/8390/8490 ds39629b-page 240 preliminary ? 2004 microchip technology inc. 18.8 use of the ccp2 trigger an a/d conversion can be started by the ?special event trigger? of the ccp2 module. this requires that the ccp2m3:ccp2m0 bits (ccp2con<3:0>) be pro- grammed as ? 1011 ? and that the a/d module is enabled (adon bit is set). when the trigger occurs, the go/done bit will be set, starting the a/d acquisition and conversion and the timer1 (or timer3) counter will be reset to zero. timer1 (or timer3) is reset to automat- ically repeat the a/d acquisition period with minimal software overhead (moving adresh/adresl to the desired location). the appropriate analog input chan- nel must be selected and the minimum acquisition period is either timed by the user, or an appropriate t acq time selected before the ?special event trigger? sets the go/done bit (starts a conversion). if the a/d module is not enabled (adon is cleared), the ?special event trigger? will be ignored by the a/d module, but will still reset the timer1 (or timer3) counter. table 18-2: registers associated with a/d operation name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir1 ?adif rc1if tx1if sspif ccp1if tmr2if tmr1if 61 pie1 ?adie rc1ie tx1ie sspie ccp1ie tmr2ie tmr1ie 61 ipr1 ?adip rc1ip tx1ip sspip ccp1ip tmr2ip tmr1ip 61 pir2 oscfif cmif ? ? bclif hlvdif tmr3if ccp2if 61 pie2 oscfie cmie ? ? bclie hlvdie tmr3ie ccp2ie 61 ipr2 oscfip cmip ? ? bclip hlvdip tmr3ip ccp2ip 61 adresh a/d result register high byte 61 adresl a/d result register low byte 61 adcon0 ? ? chs3 chs2 chs1 chs0 go/done adon 61 adcon1 ? ? vcfg1 vcfg0 pcfg3 pcfg2 pcfg1 pcfg0 61 adcon2 adfm ? acqt2 acqt1 acqt0 adcs2 adcs1 adcs0 61 porta ra7 (1) ra6 (1) ra5 ra4 ra3 ra2 ra1 ra0 62 trisa trisa7 (1) trisa6 (1) porta data direction register 62 portf read portf pins, write latf latch 62 trisf portf data direction register 62 latf portf output data latch 62 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used for a/d conversion. note 1: these pins may be configured as port pins depending on the oscillator mode selected.
? 2004 microchip technology inc. preliminary ds39629b-page 241 PIC18F6390/6490/8390/8490 19.0 comparator module the analog comparator module contains two comparators that can be configured in a variety of ways. the inputs can be selected from the analog inputs multiplexed with pins rf3 through rf6, as well as the on-chip voltage reference (see section 20.0 ?comparator voltage reference module? ). the digi- tal outputs (normal or inverted) are available at the pin level and can also be read through the control register. the cmcon register (register 19-1) selects the comparator input and output configuration. block diagrams of the various comparator configurations are shown in figure 19-1. register 19-1: cmcon: comp arator control register r-0 r-0 r/w-0 r/w-0 r/w-0 r/w-1 r/w-1 r/w-1 c2out c1out c2inv c1inv cis cm2 cm1 cm0 bit 7 bit 0 bit 7 c2out : comparator 2 output bit when c2inv = 0 : 1 = c2 v in + > c2 v in - 0 = c2 v in + < c2 v in - when c2inv = 1 : 1 = c2 v in + < c2 v in - 0 = c2 v in + > c2 v in - bit 6 c1out : comparator 1 output bit when c1inv = 0 : 1 = c1 v in + > c1 v in - 0 = c1 v in + < c1 v in - when c1inv = 1 : 1 = c1 v in + < c1 v in - 0 = c1 v in + > c1 v in - bit 5 c2inv : comparator 2 output inversion bit 1 = c2 output inverted 0 = c2 output not inverted bit 4 c1inv : comparator 1 output inversion bit 1 = c1 output inverted 0 = c1 output not inverted bit 3 cis : comparator input switch bit when cm2:cm0 = 110 : 1 =c1 v in - connects to rf5/an10 c2 v in - connects to rf3/an8 0 =c1 v in - connects to rf6/an11 c2 v in - connects to rf4/an9 bit 2-0 cm2:cm0 : comparator mode bits figure 19-1 shows the comparator modes and the cm2:cm0 bit settings. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 242 preliminary ? 2004 microchip technology inc. 19.1 comparator configuration there are eight modes of operation for the compara- tors, shown in figure 19-1. bits cm2:cm0 of the cmcon register are used to select these modes. the trisf register controls the data direction of the com- parator pins for each mode. if the comparator mode is changed, the comparator output level may not be valid for the specified mode change delay shown in section 26.0 ?electrical characteristics? . figure 19-1: comparator i/o operating modes note: comparator interrupts should be disabled during a comparator mode change; otherwise, a false interrupt may occur. c1 v in - v in + off (read as ? 0 ?) comparators reset (por default value) a a cm2:cm0 = 000 c2 v in - v in + off (read as ? 0 ?) a a c1 v in - v in + c1out two independent comparators a a cm2:cm0 = 010 c2 v in - v in + c2out a a c1 v in - v in + c1out two common reference comparators a a cm2:cm0 = 100 c2 v in - v in + c2out a d c2 v in - v in + off (read as ? 0 ?) one independent comparator with output d d cm2:cm0 = 001 c1 v in - v in + c1out a a c1 v in - v in + off (read as ? 0 ?) comparators off d d cm2:cm0 = 111 c2 v in - v in + off (read as ? 0 ?) d d c1 v in - v in + c1out four inputs multiplexed to two comparators a a cm2:cm0 = 110 c2 v in - v in + c2out a a from v ref module cis = 0 cis = 1 cis = 0 cis = 1 c1 v in - v in + c1out two common reference comparators with outputs a a cm2:cm0 = 101 c2 v in - v in + c2out a d a = analog input, port reads zeros always d = digital input cis (cmcon<3>) is the comparator input switch cv ref c1 v in - v in + c1out two independent comparators with outputs a a cm2:cm0 = 011 c2 v in - v in + c2out a a rf1/an6/c2out*/seg19 rf2/an7/c1out*/seg20 rf2/an7/c1out*/seg20 * setting the trisf<2:1> bits will disable the comparator outputs by configuring the pins as inputs. rf6/an11/ rf5/an10/ rf4/an9/ rf3/an8/ cv ref /seg23 seg24 seg22 seg21 rf6/an11/ rf5/an10/ rf4/an9/ rf3/an8/ cv ref /seg23 seg24 seg22 seg21 rf6/an11/ rf5/an10/ rf4/an9/ rf3/an8/ cv ref /seg23 seg24 seg22 seg21 rf6/an11/ rf5/an10/ rf4/an9/ rf3/an8/ cv ref /seg23 seg24 seg22 seg21 rf6/an11/ rf5/an10/ rf4/an9/ rf3/an8/ cv ref /seg23 seg24 seg22 seg21 rf6/an11/ rf5/an10/ rf4/an9/ rf3/an8/ cv ref /seg23 seg24 seg22 seg21 rf6/an11/ rf5/an10/ rf4/an9/ rf3/an8/ cv ref /seg23 seg24 seg22 seg21 rf1/an6/c2out*/seg19 rf2/an7/c1out*/seg20 rf6/an11/ rf5/an10/ rf4/an9/ rf3/an8/ cv ref /seg23 seg24 seg22 seg21
? 2004 microchip technology inc. preliminary ds39629b-page 243 PIC18F6390/6490/8390/8490 19.2 comparator operation a single comparator is shown in figure 19-2, along with the relationship between the analog input levels and the digital output. when the analog input at v in + is less than the analog input v in -, the output of the comparator is a digital low level. when the analog input at v in + is greater than the analog input v in -, the output of the comparator is a digital high level. the shaded areas of the output of the comparator in figure 19-2 represent the uncertainty, due to input offsets and response time. 19.3 comparator reference depending on the comparator operating mode, either an external or internal voltage reference may be used. the analog signal present at v in - is compared to the signal at v in + and the digital output of the comparator is adjusted accordingly (figure 19-2). figure 19-2: single comparator 19.3.1 external reference signal when external voltage references are used, the comparator module can be configured to have the com- parators operate from the same, or different reference sources. however, threshold detector applications may require the same reference. the reference signal must be between v ss and v dd and can be applied to either pin of the comparator(s). 19.3.2 internal reference signal the comparator module also allows the selection of an internally generated voltage reference from the com- parator voltage reference module. this module is described in more detail in section 20.0 ?comparator voltage reference module? . the internal reference is only available in the mode where four inputs are multiplexed to two comparators (cm2:cm0 = 110 ). in this mode, the internal voltage reference is applied to the v in + pin of both comparators. 19.4 comparator response time response time is the minimum time, after selecting a new reference voltage or input source, before the comparator output has a valid level. if the internal ref- erence is changed, the maximum delay of the internal voltage reference must be considered when using the comparator outputs. otherwise, the maximum delay of the comparators should be used (see section 26.0 ?electrical characteristics? ). 19.5 comparator outputs the comparator outputs are read through the cmcon register. these bits are read-only. the comparator outputs may also be directly output to the rf2 and rf1 i/o pins. when enabled, multiplexors in the output path of the rf2 and rf1 pins will switch and the output of each pin will be the unsynchronized output of the comparator. the uncertainty of each of the comparators is related to the input offset voltage and the response time given in the specifications. figure 19-3 shows the comparator output block diagram. the trisf bits will still function as an output enable/ disable for the rf2 and rf1 pins while in this mode. the polarity of the comparator outputs can be changed using the c2inv and c1inv bits (cmcon<5:4>). ? + v in + v in - output output v in - v in + note 1: when reading the port register, all pins configured as analog inputs will read as a ? 0 ?. pins configured as digital inputs will convert an analog input according to the schmitt trigger input specification. 2: analog levels on any pin defined as a digital input may cause the input buffer to consume more current than is specified.
PIC18F6390/6490/8390/8490 ds39629b-page 244 preliminary ? 2004 microchip technology inc. figure 19-3: comparator output block diagram 19.6 comparator interrupts the comparator interrupt flag is set whenever there is a change in the output value of either comparator. software will need to maintain information about the status of the output bits, as read from cmcon<7:6>, to determine the actual change that occurred. the cmif bit (pir2<6>) is the comparator interrupt flag. the cmif bit must be reset by clearing it. since it is also possible to write a ? 1 ? to this register, a simulated interrupt may be initiated. both the cmie bit (pie2<6>) and the peie bit (intcon<6>) must be set to enable the interrupt. in addition, the gie bit (intcon<7>) must also be set. if any of these bits are clear, the interrupt is not enabled, though the cmif bit will still be set if an interrupt condition occurs. the user, in the interrupt service routine, can clear the interrupt in the following manner: a) any read or write of cmcon will end the mismatch condition. b) clear flag bit cmif. a mismatch condition will continue to set flag bit cmif. reading cmcon will end the mismatch condition and allow flag bit cmif to be cleared. 19.7 comparator operation during sleep when a comparator is active and the device is placed in sleep mode, the comparator remains active and the interrupt is functional, if enabled. this interrupt will wake-up the device from sleep mode, when enabled. while the comparator is powered up, higher sleep currents than shown in the power-down current specification will occur. each operational comparator will consume additional current, as shown in the comparator specifications. to minimize power consumption while in sleep mode, turn off the comparators (cm2:cm0 = 111 ) before entering sleep. if the device wakes up from sleep, the contents of the cmcon register are not affected. 19.8 effects of a reset a device reset forces the cmcon register to its reset state, causing the comparator module to be in the comparator reset mode (cm2:cm0 = 000) . this ensures that all potential inputs are analog inputs. device current is minimized when analog inputs are present at reset time. the comparators are powered down during the reset interval. dq en to rf2 or rf1 pin bus data set multiplex cmif bit -+ port pins read cmcon reset from other comparator cxinv dq en cl note: if a change in the cmcon register (c1out or c2out) should occur when a read operation is being executed (start of the q2 cycle), then the cmif (pir registers) interrupt flag may not get set.
? 2004 microchip technology inc. preliminary ds39629b-page 245 PIC18F6390/6490/8390/8490 19.9 analog input connection considerations a simplified circuit for an analog input is shown in figure 19-4. since the analog pins are connected to a digital output, they have reverse biased diodes to v dd and v ss . the analog input, therefore, must be between v ss and v dd . if the input voltage deviates from this range by more than 0.6v in either direction, one of the diodes is forward biased and a latch-up condition may occur. a maximum source impedance of 10 k ? is recommended for the analog sources. any external component connected to an analog input pin, such as a capacitor or a zener diode, should have very little leakage current. figure 19-4: comparator analog input model table 19-1: registers associated with comparator module va r s < 10k a in c pin 5 pf v dd v t = 0.6v v t = 0.6v r ic i leakage 500 na v ss legend: c pin = input capacitance v t = threshold voltage i leakage = leakage current at the pin due to various junctions r ic = interconnect resistance r s = source impedance va = analog voltage comparator input name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page cmcon c2out c1out c2inv c1inv cis cm2 cm1 cm0 61 cvrcon cvren cvroe cvrr cvrss cvr3 cvr2 cvr1 cvr0 61 intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir2 oscfif cmif ? ? bclif hlvdif tmr3if ccp2if 61 pie2 oscfie cmie ? ? bclie hlvdie tmr3ie ccp2ie 61 ipr2 oscfip cmip ? ? bclip hlvdip tmr3ip ccp2ip 61 portf read portf pins, write latf latch 62 latf latf data output register 62 trisf portf data direction register 62 legend: ? = unimplemented, read as ? 0 ?. shaded cells are unused by the comparator module.
PIC18F6390/6490/8390/8490 ds39629b-page 246 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 247 PIC18F6390/6490/8390/8490 20.0 comparator voltage reference module the comparator voltage reference is a 16-tap resistor ladder network that provides a selectable reference voltage. although its primary purpose is to provide a reference for the analog comparators, it may also be used independently of them. a block diagram is of the module shown in figure 20-1.the resistor ladder is segmented to provide two ranges of cv ref values and has a power-down function to conserve power when the reference is not being used. the module?s supply reference can be provided from either device v dd /v ss , or an external voltage reference. 20.1 configuring the comparator voltage reference the voltage reference module is controlled through the cvrcon register (register 20-1). the comparator voltage reference provides two ranges of output voltage, each with 16 distinct levels. the range to be used is selected by the cvrr bit (cvrcon<5>). the primary difference between the ranges is the size of the steps selected by the cv ref selection bits (cvr3:cvr0), with one range offering finer resolution. the equations used to calculate the output of the comparator voltage reference are as follows: if cvrr = 1 : cv ref = ((cvr3:cvr0)/24) x cv rsrc if cvrr = 0 : cv ref = (cv dd x 1/4) + (((cvr3:cvr0)/32) x cv rsrc ) the comparator reference supply voltage can come from either v dd and v ss , or the external v ref + and v ref - that are multiplexed with ra2 and ra3. the voltage source is selected by the cvrss bit (cvrcon<4>). the settling time of the comparator voltage reference must be considered when changing the cv ref output (see table 26-3 in section 26.0 ?electrical characteristics? ). register 20-1: cvrcon: comparat or voltage reference control register r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 cvren cvroe (1) cvrr cvrss cvr3 cvr2 cvr1 cvr0 bit 7 bit 0 bit 7 cvren : comparator voltage reference enable bit 1 = cv ref circuit powered on 0 = cv ref circuit powered down bit 6 cvroe : comparator v ref output enable bit (1) 1 = cv ref voltage level is also output on the rf5/an10/cv ref /seg23 pin 0 = cv ref voltage is disconnected from the rf5/an10/cv ref /seg23 pin bit 5 cvrr : comparator v ref range selection bit 1 = 0.00 cv rsrc to 0.75 cv rsrc , with cv rsrc /24 step size 0 = 0.25 cv rsrc to 0.75 cv rsrc , with cv rsrc /32 step size bit 4 cvrss : comparator v ref source selection bit 1 = comparator reference source, cv rsrc = (v ref +) ? (v ref -) 0 = comparator reference source, cv rsrc = v dd ? v ss bit 3-0 cvr3:cvr0: comparator v ref value selection bits (0 (cvr3:cvr0) 15) when cvrr = 1 : cv ref = ((cvr3:cvr0)/24) ? (cv rsrc ) when cvrr = 0 : cv ref = (cv rsrc /4) + ((cvr3:cvr0)/32) ? (cv rsrc ) note 1: cvroe overrides the trisf<5> bit setting if enabled for output; rf5 must also be configured as an input by setting trisf<5> to ? 1 ?. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 248 preliminary ? 2004 microchip technology inc. figure 20-1: comparator voltage reference block diagram 20.2 voltage reference accuracy/error the full range of voltage reference cannot be realized due to the construction of the module. the transistors on the top and bottom of the resistor ladder network (figure 20-1) keep cv ref from approaching the refer- ence source rails. the voltage reference is derived from the reference source; therefore, the cv ref output changes with fluctuations in that source. the tested absolute accuracy of the voltage reference can be found in section 26.0 ?electrical characteristics? . 20.3 operation during sleep when the device wakes up from sleep through an interrupt or a watchdog timer time-out, the contents of the cvrcon register are not affected. to minimize current consumption in sleep mode, the voltage reference should be disabled. 20.4 effects of a reset a device reset disables the voltage reference by clearing bit cvren (cvrcon<7>). this reset also disconnects the reference from the ra2 pin by clearing bit cvroe (cvrcon<6>) and selects the high-voltage range by clearing bit cvrr (cvrcon<5>). the cvr value select bits are also cleared. 20.5 connection considerations the voltage reference module operates independently of the comparator module. the output of the reference generator may be connected to the rf5 pin if the trisf<5> bit and the cvroe bit are both set. enabling the voltage reference output onto the rf5 pin, with an input signal present, will increase current consumption. connecting rf5 as a digital output with cvrss enabled will also increase current consumption. the rf5 pin can be used as a simple d/a output with limited drive capability. due to the limited current drive capability, a buffer must be used on the voltage reference output for external connections to v ref . figure 20-2 shows an example buffering technique. 16 to 1 mux cvr3:cvr0 8r r cvren cvrss = 0 v dd v ref + cvrss = 1 8r cvrss = 0 v ref - cvrss = 1 r r r r r r 16 steps cvrr cv ref
? 2004 microchip technology inc. preliminary ds39629b-page 249 PIC18F6390/6490/8390/8490 figure 20-2: voltage reference output buffer example table 20-1: registers associated with the comparator voltage reference cv ref output + ? cv ref module voltage reference output impedance r (1) rf5 note 1: r is dependent upon the voltage reference configuration bits, cvrcon<3:0> and cvrcon<5>. pic18fxxxx name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page cvrcon cvren cvroe cvrr cvrss cvr3 cvr2 cvr1 cvr0 61 cmcon c2out c1out c2inv c1inv cis cm2 cm1 cm0 61 trisf portf data direction register 62 legend: shaded cells are not used with the comparator voltage reference.
PIC18F6390/6490/8390/8490 ds39629b-page 250 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 251 PIC18F6390/6490/8390/8490 21.0 high/low-voltage detect (hlvd) PIC18F6390/6490/8390/8490 devices have a high/low-voltage detect module (hlvd). this is a pro- grammable circuit that allows the user to specify both a device voltage trip point and the direction of change from that point. if the device experiences an excursion past the trip point in that direction, an interrupt flag is set. if the interrupt is enabled, the program execution will branch to the interrupt vector address and the software can then respond to the interrupt. the high/low-voltage detect control register (register 21-1) completely controls the operation of the hlvd module. this allows the circuitry to be ?turned off? by the user under software control, which minimizes the current consumption for the device. the block diagram for the hlvd module is shown in figure 21-1. register 21-1: hlvdcon: high/low-voltage de tect control register r/w-0 u-0 r-0 r/w-0 r/w-0 r/w-1 r/w-0 r/w-1 vdirmag ? irvst hlvden hlvdl3 (1) hlvdl2 (1) hlvdl1 (1) hlvdl0 (1) bit 7 bit 0 bit 7 vdirmag: voltage direction magnitude select bit 1 = event occurs when voltage equals or exceeds trip point (hlvdl3:hlvdl0) 0 = event occurs when voltage equals or falls below trip point (hlvdl3:hlvdl0) bit 6 unimplemented: read as ? 0 ? bit 5 irvst: internal reference voltage stable flag bit 1 = indicates that the voltage detect logic will generate the interrupt flag at the specified voltage range 0 = indicates that the voltage detect logic will not generate the interrupt flag at the specified voltage range and the hlvd interrupt should not be enabled bit 4 hlvden: high/low-voltage detect power enable bit 1 = hlvd enabled 0 = hlvd disabled bit 3-0 hlvdl3:hlvdl0: voltage detection limit bits (1) 1111 = external analog input is used (input comes from the hlvdin pin) 1110 = 4.41v-4.87v 1101 = 4.11v-4.55v 1100 = 3.92v-4.34v 1011 = 3.72v-4.12v 1010 = 3.53v-3.91v 1001 = 3.43v-3.79v 1000 = 3.24v-3.58v 0111 = 2.95v-3.26v 0110 = 2.75v-3.03v 0101 = 2.64v-2.92v 0100 = 2.43v-2.69v 0011 = 2.35v-2.59v 0010 = 2.16v-2.38v 0001 = 1.96v-2.16v 0000 = reserved note 1: hlvdl3:hlvdl0 modes that result in a trip point below the valid operating voltage of the device are not tested. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 252 preliminary ? 2004 microchip technology inc. the module is enabled by setting the hlvden bit. each time that the hlvd module is enabled, the cir- cuitry requires some time to stabilize. the irvst bit is a read-only bit and is used to indicate when the circuit is stable. the module can only generate an interrupt after the circuit is stable and irvst is set. the vdirmag bit determines the overall operation of the module. when vdirmag is cleared, the module monitors for drops in v dd below a pre-determined set point. when the bit is set, the module monitors for rises in v dd above the set point. 21.1 operation when the hlvd module is enabled, a comparator uses an internally generated reference voltage as the set point. the set point is compared with the trip point where each node in the resistor divider represents a trip point voltage. the ?trip point? voltage is the voltage level at which the device detects a high or low-voltage event, depending on the configuration of the module. when the supply voltage is equal to the trip point, the voltage tapped off of the resistor array is equal to the internal reference voltage generated by the voltage reference module. the comparator then generates an interrupt signal by setting the hlvdif bit. the trip point voltage is software programmable to any one of 16 values. the trip point is selected by program- ming the hlvdl3:hlvdl0 bits (hlvdcon<3:0>). the hlvd module has an additional feature that allows the user to supply the trip voltage to the module from an external source. this mode is enabled when bits hlvdl3:hlvdl0 are set to ? 1111 ?. in this state, the comparator input is multiplexed from the external input pin, hlvdin. this gives users flexibility because it allows them to configure the high/low-voltage detect interrupt to occur at any voltage in the valid operating range. figure 21-1: hlvd module block diagram (with external input) set v dd 16 to 1 mux hlvden hlvdcon hlvdin hlvdl3:hlvdl0 register hlvdin v dd externally generated trip point hlvdif hlvden boren internal voltage reference vdirmag
? 2004 microchip technology inc. preliminary ds39629b-page 253 PIC18F6390/6490/8390/8490 21.2 hlvd setup the following steps are needed to set up the hlvd module: 1. disable the module by clearing the hlvden bit (hlvdcon<4>). 2. write the value to the hlvdl3:hlvdl0 bits that selects the desired hlvd trip point. 3. set the vdirmag bit to detect high voltage (vdirmag = 1 ) or low voltage (vdirmag = 0 ). 4. enable the hlvd module by setting the hlvden bit. 5. clear the hlvd interrupt flag (pir2<2>), which may have been set from a previous interrupt. 6. enable the hlvd interrupt, if interrupts are desired, by setting the hlvdie and gie bits (pie<2> and intcon<7>). an interrupt will not be generated until the irvst bit is set. 21.3 current consumption when the module is enabled, the hlvd comparator and voltage divider are enabled and will consume static current. the total current consumption, when enabled, is specified in electrical specification parameter #d022b. depending on the application, the hlvd module does not need to be operating constantly. to decrease the current requirements, the hlvd circuitry may only need to be enabled for short periods where the voltage is checked. after doing the check, the hlvd module may be disabled. 21.4 hlvd start-up time the internal reference voltage of the hlvd module, specified in electrical specification parameter #d423, may be used by other internal circuitry, such as the programmable brown-out reset. if the hlvd or other circuits using the voltage reference are disabled to lower the device?s current consumption, the reference voltage circuit will require time to become stable before a low or high-voltage condition can be reliably detected. this start-up time, t irvst , is an interval that is independent of device clock speed. it is specified in electrical specification parameter 36 (table 26-10). the hlvd interrupt flag is not enabled until t irvst has expired and a stable reference voltage is reached. for this reason, brief excursions beyond the set point may not be detected during this interval. refer to figure 21-2 or figure 21-3. figure 21-2: low-voltage detect operation (vdirmag = 0 ) v lvd v dd hlvdif v lvd v dd enable hlvd t ivrst hlvdif may not be set enable hlvd hlvdif hlvdif cleared in software hlvdif cleared in software hlvdif cleared in software, case 1: case 2: hlvdif remains set since hlvd condition still exists t ivrst internal reference is stable internal reference is stable irvst irvst
PIC18F6390/6490/8390/8490 ds39629b-page 254 preliminary ? 2004 microchip technology inc. figure 21-3: high-voltage detect operation (vdirmag = 1 ) 21.5 applications in many applications, the ability to detect a drop below, or rise above a particular threshold, is desirable. for example, the hlvd module could be periodically enabled to detect usb attach or detach. this assumes the device is powered by a lower voltage source than the universal serial bus when detached. an attach would indicate a high-voltage detect from, for example, 3.3v to 5v (the voltage on usb) and vice versa for a detach. this feature could save a design a few extra components and an attach signal (input pin). for general battery applications, figure 21-4 shows a possible voltage curve. over time, the device voltage decreases. when the device voltage reaches voltage v a , the hlvd logic generates an interrupt at time t a . the interrupt could cause the execution of an isr, which would allow the application to perform ?house- keeping tasks? and perform a controlled shutdown before the device voltage exits the valid operating range at t b . the hlvd, thus, would give the application a time window, represented by the difference between t a and t b , to safely exit. figure 21-4: typical low-voltage detect application v lvd v dd hlvdif v lvd v dd enable hlvd t ivrst hlvdif may not be set enable hlvd hlvdif hlvdif cleared in software hlvdif cleared in software hlvdif cleared in software, case 1: case 2: hlvdif remains set since hlvd condition still exists t ivrst irvst internal reference is stable internal reference is stable irvst time voltage v a v b t a t b v a = hlvd trip point v b = minimum valid device operating voltage legend:
? 2004 microchip technology inc. preliminary ds39629b-page 255 PIC18F6390/6490/8390/8490 21.6 operation during sleep when enabled, the hlvd circuitry continues to operate during sleep. if the device voltage crosses the trip point, the hlvdif bit will be set and the device will wake-up from sleep. device execution will continue from the interrupt vector address if interrupts have been globally enabled. 21.7 effects of a reset a device reset forces all registers to their reset state. this forces the hlvd module to be turned off. table 21-1: registers associated with high/low-voltage detect module name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page hlvdcon vdirmag ? irvst hlvden hlvdl3 hlvdl2 hlvdl1 hlvdl0 60 intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir2 oscfif cmif ? ? bclif hlvdif tmr3if ccp2if 61 pie2 oscfie cmie ? ? bclie hlvdie tmr3ie ccp2ie 61 ipr2 oscfip cmip ? ? bclip hlvdip tmr3ip ccp2ip 61 legend: ? = unimplemented, read as ? 0 ?. shaded cells are unused by the hlvd module.
PIC18F6390/6490/8390/8490 ds39629b-page 256 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 257 PIC18F6390/6490/8390/8490 22.0 liquid crystal display (lcd) driver module the liquid crystal display (lcd) driver module generates the timing control to drive a static or multiplexed lcd panel. in the 80-pin devices (pic18f8390/8490), the module drives the panels of up to four commons and up to 48 segments and in the 64-pin devices (PIC18F6390/6490), the module drives the panels of up to four commons and up to 32 segments. it also provides control of the lcd pixel data. the lcd driver module supports: direct driving of lcd panel three lcd clock sources with selectable prescaler up to four commons: - static - 1/2 multiplex - 1/3 multiplex - 1/4 multiplex up to 48 (in 80-pin devices)/32 (in 64-pin devices) segments static, 1/2 or 1/3 lcd bias a simplified block diagram of the module is shown in figure 22-1. figure 22-1: lcd driver module block diagram com3:com0 clock source timing control data bus select and prescaler intrc oscillator f osc /4 t13cki 192 to 48 mux seg<47:0> to i/o pads to i/o pads 24 x 8 (= 4 x 48) lcddatax registers lcdcon lcdps lcdsex
PIC18F6390/6490/8390/8490 ds39629b-page 258 preliminary ? 2004 microchip technology inc. 22.1 lcd registers the lcd driver module has 32 registers: lcd control register (lcdcon) lcd phase register (lcdps) six lcd segment enable registers (lcdse5:lcdse0) 24 lcd data registers (lcddata23:lcddata0) the lcdcon register, shown in register 22-1, controls the overall operation of the module. once the module is configured, the lcden (lcdcon<7>) bit is used to enable or disable the lcd module. the lcd panel can also operate during sleep by clearing the slpen (lcdcon<6>) bit. the lcdps register, shown in register 22-2, configures the lcd clock source prescaler and the type of waveform, type-a or type-b. details on these features are provided in section 22.2 ?lcd clock source selection? , section 22.3 ?lcd bias types? and section 22.8 ?lcd waveform generation? . register 22-1: lcdcon: lcd control register r/w-0 r/w-0 r/c-0 u-0 r/w-0 r/w-0 r/w-0 r/w-0 lcden slpen werr ? cs1 cs0 lmux1 lmux0 bit 7 bit 0 bit 7 lcden: lcd driver enable bit 1 = lcd driver module is enabled 0 = lcd driver module is disabled bit 6 slpen: lcd driver enable in sleep mode bit 1 = lcd driver module is disabled in sleep mode 0 = lcd driver module is enabled in sleep mode bit 5 werr: lcd write failed error bit 1 = lcddatax register written while lcdps = 0 (must be cleared in software) 0 = no lcd write error bit 4 unimplemented: read as ? 0 ? bit 3-2 cs1:cs0: clock source select bits 00 = (f osc /4)/8192 01 = t13cki (timer1)/32 1x = intrc (31.25 khz)/32 bit 1-0 lmux1:lmux0: commons select bits legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? c = only clearable bit ?1? = bit is set ?0? = bit is cleared x = bit is unknown -n = value at por lmux1:lmux0 multiplex maximum number of pixels (pic18f6x90) maximum number of pixels (pic18f8x90) bias 00 static (com0) 32 48 static 01 1/2 (com1:com0) 64 96 1/2 or 1/3 10 1/3 (com2:com0) 96 144 1/2 or 1/3 11 1/4 (com3:com0) 128 192 1/3
? 2004 microchip technology inc. preliminary ds39629b-page 259 PIC18F6390/6490/8390/8490 register 22-2: lcdps: lcd phase register r/w-0 r/w-0 r-0 r-0 r/w-0 r/w-0 r/w-0 r/w-0 wft biasmd lcda wa lp3 lp2 lp1 lp0 bit 7 bit 0 bit 7 wft: waveform type select bit 1 = type-b waveform (phase changes on each frame boundary) 0 = type-a waveform (phase changes within each common type) bit 6 biasmd: bias mode select bit when lmux1:lmux0 = 00 : 0 = static bias mode (do not set this bit to ? 1 ?) when lmux1:lmux0 = 01 : 1 = 1/2 bias mode 0 = 1/3 bias mode when lmux1:lmux0 = 10 : 1 = 1/2 bias mode 0 = 1/3 bias mode when lmux1:lmux0 = 11 : 0 = 1/3 bias mode (do not set this bit to ? 1 ?) bit 5 lcda: lcd active status bit 1 = lcd driver module is active 0 = lcd driver module is inactive bit 4 wa: lcd write allow status bit 1 = write into the lcddatax registers is allowed 0 = write into the lcddatax registers is not allowed bit 3-0 lp3:lp0: lcd prescaler select bits 1111 = 1:16 1110 = 1:15 1101 = 1:14 1100 = 1:13 1011 = 1:12 1010 = 1:11 1001 = 1:10 1000 = 1:9 0111 = 1:8 0110 = 1:7 0101 = 1:6 0100 = 1:5 0011 = 1:4 0010 = 1:3 0001 = 1:2 0000 = 1:1 legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 260 preliminary ? 2004 microchip technology inc. the lcdse5:lcdse0 registers configure the functions of the port pins. setting the segment enable bit for a particular segment configures that pin as an lcd driver. there are six lcd segment enable registers listed in table 22-1. the prototype lcdse register is shown in register 22-3. table 22-1: lcdse registers and associated segments . once the module is initialized for the lcd panel, the individual bits of the lcddata23:lcddata0 registers are cleared or set to represent a clear or dark pixel, respectively. specific sets of lcddata registers are used with specific segments and common signals. each bit represents a unique combination of a specific segment connected to a specific common. individual lcddata bits are named by the convention ?sxxcy?, with ?xx? as the segment number and ?y? as the common number. the relationship is summarized in table 22-2. the prototype lcddata register is shown in register 22-4. register 22-3: lcdsex: lcd segment enable registers register segments lcdse0 7:0 lcdse1 15:8 lcdse2 23:16 lcdse3 31:24 lcdse4 39:32 lcdse5 47:40 note: the lcdse5:lcdse4 registers are not implemented in pic18f6x90 devices. note: writing into the registers lcddata4, lcddata5, lcddata10, lcddata11, lcddata16, lcddata17, lcddata22 and lcddata23 in pic18f6x90 devices will not affect the status of any pixel and these registers can be used as general purpose registers. r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 se(n + 7) se(n + 6) se(n + 5) se(n + 4) se(n + 3) se(n + 2) se(n + 1) se(n) bit 7 bit 0 bit 7-0 seg(n + 7):seg(n): segment enable bits for lcdse0: n = 0 for lcdse1: n = 8 for lcdse2: n = 16 for lcdse3: n = 24 for lcdse4: n = 32 for lcdse5: n = 40 1 = segment function of the pin is enabled, digital i/o disabled 0 = i/o function of the pin is enabled legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
? 2004 microchip technology inc. preliminary ds39629b-page 261 PIC18F6390/6490/8390/8490 table 22-2: lcddata registers and bits for segment and com combinations register 22-4: lcddatax: lcd data registers segments com lines 0123 0 through 7 lcddata0 lcddata6 lcddata12 lcddata18 s00c0:s07c0 s00c1:s07c1 s00c2:s07c2 s00c3:s07c3 8 through 15 lcddata1 lcddata7 lcddata13 lcddata19 s08c0:s15c0 s08c1:s15c1 s08c2:s15c2 s08c0:s15c3 16 through 23 lcddata2 lcddata8 lcddata14 lcddata20 s16c0:s23c0 s16c1:s23c1 s16c2:s23c2 s16c3:s23c3 24 through 31 lcddata3 lcddata9 lcddata15 lcddata21 s24c0:s31c0 s24c1:s31c1 s24c2:s31c2 s24c3:s31c3 32 through 39 lcddata4 (1) lcddata10 (1) lcddata16 (1) lcddata22 (1) s32c0:s39c0 s32c1:s39c1 s32c2:s39c2 s32c3:s39c3 40 through 47 lcddata5 (1) lcddata11 (1) lcddata17 (1) lcddata23 (1) s40c0:s47c0 s40c1:s47c1 s40c2:s47c2 s40c3:s47c3 note 1: these registers are implemented but not used as lcd data registers in 64-pin devices. they may be used as general purpose data memory. r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 r/w-0 s(n + 7)cy s(n + 6)cy s(n + 5)cy s(n + 4) cy s(n + 3)cy s(n + 2)cy s(n + 1)cy s(n)cy bit 7 bit 0 bit 7-0 s(n + 7)cy:s(n)cy: pixel on bits for lcddata0 through lcddata5: n = (8x), y = 0 for lcddata6 through lcddata11: n = (8(x ? 6)), y = 1 for lcddata12 through lcddata17: n = (8(x ? 12)), y = 2 for lcddata18 through lcddata23: n = (8(x ? 18)), y = 3 1 = pixel on (dark) 0 = pixel off (clear) legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por ?1? = bit is set ?0? = bit is cleared x = bit is unknown
PIC18F6390/6490/8390/8490 ds39629b-page 262 preliminary ? 2004 microchip technology inc. 22.2 lcd clock source selection the lcd driver module has 3 possible clock sources: (f osc /4)/8192 t13cki-clock/32 intrc/32 the first clock source is the system clock divided by 8192 ((f osc /4)/8192). this divider ratio is chosen to provide about 1 khz output when the system clock is 8 mhz. the divider is not programmable. instead, the lcd prescaler bits, lcdps<3:0>, are used to set the lcd frame clock rate. the second clock source is the timer1 oscillator/32. this also gives about 1 khz when a 32.768 khz crystal is used with the timer1 oscillator. to use the timer1 oscillator as a clock source, the t1oscen (t1con<3>) bit should be set. the third clock source is a 31.25 khz internal rc oscillator/32, which provides approximately 1 khz output. the second and third clock sources may be used to continue running the lcd while the processor is in sleep. using the bits, cs1:cs0 (lcdcon<3:2>), any of these clock sources can be selected. 22.2.1 lcd prescaler a 16-bit counter is available as a prescaler for the lcd clock. the prescaler is not directly readable or writable; its value is set by the lp3:lp0 bits (lcdps<3:0>), which determine the prescaler assignment and prescale ratio. the prescale values from 1:1 through 1:32768 in power-of-2 increments are selectable. figure 22-2: lcd cl ock generation cs1:cs0 tmr1 32 khz crystal oscillator internal rc oscillator nom f rc = 31.25 khz stat dup trip quad 4 lmux1:lmux0 4-bit prog prescaler 1, 2, 3, 4 ring counter lmux1:lmux0 com0 com1 com2 com3 8192 (f osc /4) 2 32 32 lp3:lp0 (lcdcon<3:2>) (lcdcon<1:0>) (lcdcon<1:0>) (lcdps<3:0>) system clock
? 2004 microchip technology inc. preliminary ds39629b-page 263 PIC18F6390/6490/8390/8490 22.3 lcd bias types the lcd driver module can be configured into three bias types: static bias (2 voltage levels: av ss and av dd ) 1/2 bias (3 voltage levels: av ss , 1/2 av dd and av dd ) 1/3 bias (4 voltage levels: av ss , 1/3 av dd , 2/3 av dd and av dd ) this module uses an external resistor ladder to generate the lcd bias voltages. the external resistor ladder should be connected to the bias 1 pin, bias 2 pin, bias 3 pin and v ss . the bias 1 pin should also be connected to v dd . figure 22-3 shows the proper way to connect the resistor ladder to the bias pins. 22.4 lcd multiplex types the lcd driver module can be configured into four multiplex types: static (only com0 used) 1/2 multiplex (com0 and com1 are used) 1/3 multiplex (com0, com1 and com2 are used) 1/4 multiplex (all com0, com1, com2 and com3 are used) the lmux1:lmux0 setting decides the function of the porte<6:4> bits (see table 22-3 for details). if the pin is a digital i/o, the corresponding tris bit controls the data direction. if the pin is a com drive, then the tris setting of that pin is overridden. table 22-3: porte<6:4> function 22.5 segment enables the lcdsex registers are used to select the pin function for each segment pin. the selection allows each pin to operate as either an lcd segment driver or a digital only pin. to configure the pin as a segment pin, the corresponding bits in the lcdsex registers must be set to ? 1 ?. if the pin is a digital i/o, the corresponding tris bit controls the data direction. any bit set in the lcdsex registers overrides any bit settings in the corresponding tris register. figure 22-3: lcd bias resistor ladder connection diagram note: on a power-on reset, the lmux1:lmux0 bits are ? 00 ?. lmux1: lmux0 porte<6> porte<5> porte<4> 00 digital i/o digital i/o digital i/o 01 digital i/o digital i/o com1 driver 10 digital i/o com2 driver com1 driver 11 com3 driver com2 driver com1 driver note: on a power-on reset, these pins are configured as digital i/o. v lcd 3 v lcd 2 v lcd 1 v lcd 0 to lcd driver connections for external r-ladder 10 k ? * 10 k ? * 10 k ? * lcd bias 2 lcd bias 1 lcd bias 3 * these values are provided for design guidance only and should be optimized for the application by the designer . av ss static bias 1/2 bias 1/3 bias v lcd 0av ss av ss av ss v lcd 1 ? 1/2 av dd 1/3 av dd v lcd 2 ? 1/2 av dd 2/3 av dd v lcd 3av dd av dd av dd 10 k ? *10k ? * av ss av dd * av dd * av dd * static bias 1/2 bias 1/3 bias
PIC18F6390/6490/8390/8490 ds39629b-page 264 preliminary ? 2004 microchip technology inc. 22.6 pixel control the lcddatax registers contain bits which define the state of each pixel. each bit defines one unique pixel. table 22-2 shows the correlation of each bit in the lcddatax registers to the respective common and segment signals. any lcd pixel location not being used for display can be used as general purpose ram. 22.7 lcd frame frequency the rate at which the com and seg outputs changes is called the lcd frame frequency table 22-4: frame frequency formulas table 22-5: approximate frame frequency (in hz) using f osc @ 32 mhz, timer1 @ 32.768 khz or intrc oscillator 22.8 lcd waveform generation lcd waveform generation is based on the philosophy that the net ac voltage across the dark pixel should be maximized and the net ac voltage across the clear pixel should be minimized. the net dc voltage across any pixel should be zero. the com signal represents the time slice for each common, while the seg contains the pixel data. the pixel signal (com-seg) will have no dc com- ponent and it can take only one of the two rms values. the higher rms value will create a dark pixel and a lower rms value will create a clear pixel. as the number of commons increases, the delta between the two rms values decreases. the delta represents the maximum contrast that the display can have. the lcds can be driven by two types of waveform: type-a and type-b. in type-a waveform, the phase changes within each common type, whereas in type-b waveform, the phase changes on each frame boundary. thus, type-a waveform maintains 0 v dc over a single frame, whereas type-b waveform takes two frames. figure 22-4 through figure 22-14 provide waveforms for static, half-multiplex, one-third-multiplex and quarter-multiplex drives for type-a and type-b waveforms. multiplex frame frequency = static clock source / (4 x 1 x (lp3:lp0 + 1)) 1/2 clock source / (2 x 2 x (lp3:lp0 + 1)) 1/3 clock source / (1 x 3 x (lp3:lp0 + 1)) 1/4 clock source / (1 x 4 x (lp3:lp0 + 1)) note: clock source is (f osc /4)/8192, timer1 osc/32 or intrc/32. lp3:lp0 static 1/2 1/3 1/4 1 125 125 167 125 2838311183 3 62 628362 4 50 506750 5 42 425642 6 36 364836 7 31 314231 note 1: if sleep has to be executed with lcd sleep enabled (lcdcon is ? 1 ?), then care must be taken to execute sleep only when v dc on all the pixels is ? 0 ?. 2: when the lcd clock source is (f osc /4)/8192, if sleep is executed irrespective of the lcdcon setting, the lcd goes into sleep. thus, take care to see that v dc on all pixels is ? 0 ? when sleep is executed.
? 2004 microchip technology inc. preliminary ds39629b-page 265 PIC18F6390/6490/8390/8490 figure 22-4: type-a/type-b waveforms in static drive v 1 v 0 com0 seg0 com0-seg0 com0-seg1 seg1 v 1 v 0 v 1 v 0 v 0 v 1 -v 1 v 0 1 frame com0 seg0 seg1 seg2 seg3 seg4 seg5 seg6 seg7
PIC18F6390/6490/8390/8490 ds39629b-page 266 preliminary ? 2004 microchip technology inc. figure 22-5: type-a waveforms in 1/2 mux, 1/2 bias drive v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 -v 2 -v 1 v 2 v 1 v 0 -v 2 -v 1 com0 com1 seg0 seg1 com0-seg0 com0-seg1 1 frame com1 com0 seg0 seg1 seg2 seg3
? 2004 microchip technology inc. preliminary ds39629b-page 267 PIC18F6390/6490/8390/8490 figure 22-6: type-b waveforms in 1/2 mux, 1/2 bias drive v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 -v 2 -v 1 v 2 v 1 v 0 -v 2 -v 1 com0 com1 seg0 seg1 com0-seg0 com0-seg1 com1 com0 seg0 seg1 seg2 seg3 2 frames
PIC18F6390/6490/8390/8490 ds39629b-page 268 preliminary ? 2004 microchip technology inc. figure 22-7: type-a waveforms in 1/2 mux, 1/3 bias drive v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 -v 3 -v 2 -v 1 v 3 v 2 v 1 v 0 -v 3 -v 2 -v 1 com0 com1 seg0 seg1 com0-seg0 com0-seg1 1 frame com1 com0 seg0 seg1 seg2 seg3
? 2004 microchip technology inc. preliminary ds39629b-page 269 PIC18F6390/6490/8390/8490 figure 22-8: type-b waveforms in 1/2 mux, 1/3 bias drive v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 -v 3 -v 2 -v 1 v 3 v 2 v 1 v 0 -v 3 -v 2 -v 1 com0 com1 seg0 seg1 com0-seg0 com0-seg1 com1 com0 seg0 seg1 seg2 seg3 2 frames
PIC18F6390/6490/8390/8490 ds39629b-page 270 preliminary ? 2004 microchip technology inc. figure 22-9: type-a waveforms in 1/3 mux, 1/2 bias drive v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 -v 2 -v 1 v 2 v 1 v 0 -v 2 -v 1 com0 com1 com2 seg0 seg1 com0-seg0 com0-seg1 1 frame com2 com1 com0 seg0 seg1 seg2 seg2
? 2004 microchip technology inc. preliminary ds39629b-page 271 PIC18F6390/6490/8390/8490 figure 22-10: type-b waveforms in 1/3 mux, 1/2 bias drive v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 v 2 v 1 v 0 -v 2 -v 1 v 2 v 1 v 0 -v 2 -v 1 com0 com1 com2 seg0 seg1 com0-seg0 com0-seg1 2 frames com2 com1 com0 seg0 seg1 seg2
PIC18F6390/6490/8390/8490 ds39629b-page 272 preliminary ? 2004 microchip technology inc. figure 22-11: type-a waveforms in 1/3 mux, 1/3 bias drive v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 -v 3 -v 2 -v 1 v 3 v 2 v 1 v 0 -v 3 -v 2 -v 1 com0 com1 com2 seg0 seg1 com0-seg0 com0-seg1 1 frame com2 com1 com0 seg0 seg1 seg2 seg2
? 2004 microchip technology inc. preliminary ds39629b-page 273 PIC18F6390/6490/8390/8490 figure 22-12: type-b waveforms in 1/3 mux, 1/3 bias drive v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 -v 3 -v 2 -v 1 v 3 v 2 v 1 v 0 -v 3 -v 2 -v 1 com0 com1 com2 seg0 seg1 com0-seg0 com0-seg1 2 frames com2 com1 com0 seg0 seg1 seg2
PIC18F6390/6490/8390/8490 ds39629b-page 274 preliminary ? 2004 microchip technology inc. figure 22-13: type-a waveforms in 1/4 mux, 1/3 bias drive v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 -v 3 -v 2 -v 1 v 3 v 2 v 1 v 0 -v 3 -v 2 -v 1 com0 com1 com2 com3 seg0 seg1 com0-seg0 com0-seg1 com3 com2 com1 com0 1 frame seg0 seg1
? 2004 microchip technology inc. preliminary ds39629b-page 275 PIC18F6390/6490/8390/8490 figure 22-14: type-b waveforms in 1/4 mux, 1/3 bias drive v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 -v 3 -v 2 -v 1 v 3 v 2 v 1 v 0 -v 3 -v 2 -v 1 com0 com1 com2 com3 seg0 seg1 com0-seg0 com0-seg1 com3 com2 com1 com0 2 frames seg0 seg1
PIC18F6390/6490/8390/8490 ds39629b-page 276 preliminary ? 2004 microchip technology inc. 22.9 lcd interrupts the lcd timing generation provides an interrupt that defines the lcd frame timing. this interrupt can be used to coordinate the writing of the pixel data with the start of a new frame. writing pixel data at the frame boundary allows a visually crisp transition of the image. this interrupt can also be used to synchronize external events to the lcd. for example, the interface to an external segment driver can be synchronized for segment data update to the lcd frame. a new frame is defined to begin at the leading edge of the com0 common signal. the interrupt will be set immediately after the lcd controller completes accessing all pixel data required for a frame. this will occur at a fixed interval before the frame boundary (t fint ), as shown in figure 22-15. the lcd controller will begin to access data for the next frame within the interval from the interrupt to when the controller begins to access data after the interrupt (t fwr ). new data must be written within t fwr , as this is when the lcd controller will begin to access the data for the next frame. when the lcd driver is running with type-b waveforms and the lmux1:lmux0 bits are not equal to ? 00 ?, there are some additional issues that must be addressed. since the dc voltage on the pixel takes two frames to maintain zero volts, the pixel data must not change between subsequent frames. if the pixel data were allowed to change, the waveform for the odd frames would not necessarily be the complement of the waveform generated in the even frames and a dc component would be introduced into the panel. there- fore, when using type-b waveforms, the user must synchronize the lcd pixel updates to occur within a subframe after the frame interrupt. to correctly sequence writing while in type-b, the interrupt will only occur on complete phase intervals. if the user attempts to write when the write is disabled, the werr (lcdcon<5>) bit is set. figure 22-15: example waveforms and interrupt timing in quarter-duty cycle drive note: the interrupt is not generated when the type-a waveform is selected and when the type-b with no multiplex (static) is selected. frame boundary frame boundary lcd interrupt occurs controller accesses next frame data t fint t fwr t fwr =t frame /2*(lmux1:lmux0 + 1) + t cy /2 t fint =(t fwr /2 ? (2 t cy + 40 ns)) minimum = 1.5(t frame /4) ? (2 t cy + 40 ns) (t fwr /2 ? (1 t cy + 40 ns)) maximum = 1.5(t frame /4) ? (1 t cy + 40 ns) frame boundary v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 com0 com1 com2 com3 2 frames
? 2004 microchip technology inc. preliminary ds39629b-page 277 PIC18F6390/6490/8390/8490 22.10 operation during sleep the lcd module can operate during sleep. the selec- tion is controlled by bit slpen (lcdcon<6>). setting the slpen bit allows the lcd module to go to sleep. clearing the slpen bit allows the module to continue to operate during sleep. if a sleep instruction is executed and slpen = 1 , the lcd module will cease all functions and go into a very low current consumption mode. the module will stop operation immediately and drive the minimum lcd voltage on both segment and common lines. figure 22-16 shows this operation. to ensure that no dc component is introduced on the panel, the sleep instruction should be executed imme- diately after a lcd frame boundary. the lcd interrupt can be used to determine the frame boundary. see section 22.9 ?lcd interrupts? for the formulas to calculate the delay. if a sleep instruction is executed and slpen = 0 , the module will continue to display the current contents of the lcddata registers. to allow the module to continue operation while in sleep, the clock source must be either the internal rc oscillator or timer1 external oscillator. while in sleep, the lcd data cannot be changed. the lcd module current consumption will not decrease in this mode; however, the overall consumption of the device will be lower due to shut down of the core and other peripheral functions. if the system clock is selected and the module is programmed to not sleep, the module will ignore the slpen bit and stop operation immediately. the minimum lcd voltage will then be driven onto the segments and commons. figure 22-16: sleep entry/exit when slpen = 1 or cs1:cs0 = 00 note: the internal rc oscillator or external timer1 oscillator must be used to operate the lcd module during sleep. sleep instruction execution wake-up 2 frames v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 v 3 v 2 v 1 v 0 com0 com1 com2 seg0
PIC18F6390/6490/8390/8490 ds39629b-page 278 preliminary ? 2004 microchip technology inc. 22.11 configuring the lcd module the following is the sequence of steps to configure the lcd module. 1. select the frame clock prescale using bits lp3:lp0 (lcdps<3:0>). 2. configure the appropriate pins to function as segment drivers using the lcdsex registers. 3. configure the lcd module for the following using the lcdcon register: - multiplex and bias mode, bits lmux1:lmux0 - timing source, bits cs1:cs0 - sleep mode, bit slpen 4. write initial values to pixel data registers, lcddata0 through lcddata23. 5. clear lcd interrupt flag, lcdif (pir3<6>) and if desired, enable the interrupt by setting bit lcdie (pie3<6>). 6. enable the lcd module by setting bit lcden (lcdcon<7>).
? 2004 microchip technology inc. preliminary ds39629b-page 279 PIC18F6390/6490/8390/8490 table 22-6: registers associated with lcd operation name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 reset values on page intcon gie/gieh peie/giel tmr0ie int0ie rbie tmr0if int0if rbif 59 pir3 ?lcdif rc2if tx2if ? ? ? ?61 pie3 ? lcdie rc2ie tx2ie ? ? ? ?61 ipr3 ? lcdip rc2ip tx2ip ? ? ? ?61 rcon ipen sboren ? ri to pd por bor 60 lcddata23 (1) s47c3 s46c3 s45c3 s44c3 s43c3 s42c3 s41c3 s40c3 63 lcddata22 (1) s39c3 s38c3 s37c3 s36c3 s35c3 s34c3 s33c3 s32c3 63 lcddata21 s31c3 s30c3 s29c3 s28c3 s27c3 s26c3 s25c3 s24c3 63 lcddata20 s23c3 s22c3 s21c3 s20c3 s19c3 s18c3 s17c3 s16c3 63 lcddata19 s15c3 s14c3 s13c3 s12c3 s11c3 s10c3 s09c3 s08c3 63 lcddata18 s07c3 s06c3 s05c3 s04c3 s03c3 s02c3 s01c3 s00c3 63 lcddata17 (1) s47c2 s46c2 s45c2 s44c2 s43c2 s42c2 s41c2 s40c2 63 lcddata16 (1) s39c2 s38c2 s37c2 s36c2 s35c2 s34c2 s33c2 s32c2 63 lcddata15 s31c2 s30c2 s29c2 s28c2 s27c2 s26c2 s25c2 s24c2 63 lcddata14 s23c2 s22c2 s21c2 s20c2 s19c2 s18c2 s17c2 s16c2 63 lcddata13 s15c2 s14c2 s13c2 s12c2 s11c2 s10c2 s09c2 s08c2 63 lcddata12 s07c2 s06c2 s05c2 s04c2 s03c2 s02c2 s01c2 s00c2 63 lcddata11 (1) s47c1 s46c1 s45c1 s44c1 s43c1 s42c1 s41c1 s40c1 63 lcddata10 (1) s39c1 s38c1 s37c1 s36c1 s35c1 s34c1 s33c1 s32c1 63 lcddata9 s31c1 s30c1 s29c1 s28c1 s27c1 s26c1 s25c1 s24c1 63 lcddata8 s23c1 s22c1 s21c1 s20c1 s19c1 s18c1 s17c1 s16c1 63 lcddata7 s15c1 s14c1 s13c1 s12c1 s11c1 s10c1 s09c1 s08c1 63 lcddata6 s07c1 s06c1 s05c1 s04c1 s03c1 s02c1 s01c1 s00c1 63 lcddata5 (1) s47c0 s46c0 s45c0 s44c0 s43c0 s42c0 s41c0 s40c0 63 lcddata4 (1) s39c0 s38c0 s37c0 s36c0 s35c0 s34c0 s33c0 s32c0 63 lcddata3 s31c0 s30c0 s29c0 s28c0 s27c0 s26c0 s25c0 s24c0 63 lcddata2 s23c0 s22c0 s21c0 s20c0 s19c0 s18c0 s17c0 s16c0 63 lcddata1 s15c0 s14c0 s13c0 s12c0 s11c0 s10c0 s09c0 s08c0 63 lcddata0 s07c0 s06c0 s05c0 s04c0 s03c0 s02c0 s01c0 s00c0 63 lcdse5 (2) se47 se46 se45 se44 se43 se42 se41 se40 64 lcdse4 (2) se39 se38 se37 se36 se35 se34 se33 se32 64 lcdse3 se31 se30 se29 se2 8 se27 se26 se25 se24 64 lcdse2 se23 se22 se21 se2 0 se19 se18 se17 se16 64 lcdse1 se15 se14 se13 se12 se11 se10 se9 se8 64 lcdse0 se7 se6 se5 se4 se3 se2 se1 se0 64 lcdcon lcden slpen werr ? cs1 cs0 lmux1 lmux0 64 lcdps wft biasmd lcda wa lp3 lp2 lp1 lp0 64 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used for a/d conversion. note 1: these registers are implemented but unused on 64-pin devices and may be used as general-purpose data ram. 2: these registers are unimplemented on 64-pin devices.
PIC18F6390/6490/8390/8490 ds39629b-page 280 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 281 PIC18F6390/6490/8390/8490 23.0 special features of the cpu PIC18F6390/6490/8390/8490 devices include several features intended to maximize reliability and minimize cost through elimination of external components. these are: oscillator selection resets: - power-on reset (por) - power-up timer (pwrt) - oscillator start-up timer (ost) - brown-out reset (bor) interrupts watchdog timer (wdt) fail-safe clock monitor two-speed start-up code protection id locations in-circuit serial programming the oscillator can be configured for the application depending on frequency, power, accuracy and cost. all of the options are discussed in detail in section 2.0 ?oscillator configurations? . a complete discussion of device resets and interrupts is available in previous sections of this data sheet. in addition to their power-up and oscillator start-up timers provided for resets, PIC18F6390/6490/8390/ 8490 devices have a watchdog timer, which is either permanently enabled via the configuration bits, or software controlled (if configured as disabled). the inclusion of an internal rc oscillator also provides the additional benefits of a fail-safe clock monitor (fscm) and two-speed start-up. fscm provides for background monitoring of the peripheral clock and automatic switchover in the event of its failure. two- speed start-up enables code to be executed almost immediately on start-up, while the primary clock source completes its start-up delays. all of these features are enabled and configured by setting the appropriate configuration register bits. 23.1 configuration bits the configuration bits can be programmed (read as ? 0 ?), or left unprogrammed (read as ? 1 ?), to select vari- ous device configurations. these bits are mapped starting at program memory location 300000h. the user will note that address 300000h is beyond the user program memory space. in fact, it belongs to the configuration memory space (300000h-3fffffh), which can only be accessed using table reads. table 23-1: configuration bits and device ids file name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 default/ unprogrammed value 300001h config1h ieso fcmen ? ? fosc3 fosc2 fosc1 fosc0 00-- 0111 300002h config2l ? ? ? borv1 borv0 boren1 boren0 pwrten ---1 1111 300003h config2h ? ? ? wdtps3 wdtps2 wdtps1 wdtps0 wdten ---1 1111 300005h config3h mclre ? ? ? ?lpt1osc ?ccp2mx 1--- -0-1 300006h config4l debug xinst ? ? ? ? ?stvren 10-- ---1 300008h config5l ? ? ? ? ? ? ?cp ---- ---1 3ffffeh devid1 dev2 dev1 dev0 rev4 rev3 rev2 rev1 rev0 xxxx xxxx (1) 3fffffh devid2 dev10 dev9 dev8 dev7 dev6 dev5 dev4 dev3 0000 xxxx (1) legend: x = unknown, u = unchanged, - = unimplemented, q = value depends on condition. shaded cells are unimplemented, read as ? 0 ?. note 1: see register 23-7 for devid values. devid registers are read-only and cannot be programmed by the user.
PIC18F6390/6490/8390/8490 ds39629b-page 282 preliminary ? 2004 microchip technology inc. register 23-1: config1h: configuration register 1 high (byte address 300001h) r/p-0 r/p-0 u-0 u-0 r/p-0 r/p-1 r/p-1 r/p-1 ieso fcmen ? ? fosc3 fosc2 fosc1 fosc0 bit 7 bit 0 bit 7 ieso: internal/external oscillator switchover bit 1 = oscillator switchover mode enabled 0 = oscillator switchover mode disabled bit 6 fcmen: fail-safe clock monitor enable bit 1 = fail-safe clock monitor enabled 0 = fail-safe clock monitor disabled bit 5-4 unimplemented: read as ? 0 ? bit 3-0 fosc3:fosc0: oscillator selection bits 11xx = external rc oscillator, clko function on ra6 101x = external rc oscillator, clko function on ra6 1001 = internal oscillator block, clko function on ra6, port function on ra7 1000 = internal oscillator block, port function on ra6 and ra7 0111 = external rc oscillator, port function on ra6 0110 = hs oscillator, pll enabled (clock frequency = 4 x fosc1) 0101 = ec oscillator, port function on ra6 0100 = ec oscillator, clko function on ra6 0011 = external rc oscillator, clko function on ra6 0010 = hs oscillator 0001 = xt oscillator 0000 = lp oscillator legend: r = readable bit p = programmable bit u = unimplemented bit, read as ?0? -n = value when device is unprogrammed u = unchanged from programmed state
? 2004 microchip technology inc. preliminary ds39629b-page 283 PIC18F6390/6490/8390/8490 register 23-2: config2l: configuration register 2 low (byte address 300002h) u-0 u-0 u-0 r/p-1 r/p-1 r/p-1 r/p-1 r/p-1 ? ? ? borv1 borv0 boren1 (1) boren0 (1) pwrten (1) bit 7 bit 0 bit 7-5 unimplemented: read as ? 0 ? bit 4-3 borv1:borv0: brown-out reset voltage bits 11 = v bor set to 2.1v 10 = v bor set to 2.8v 01 = v bor set to 4.3v 00 = v bor set to 4.6v bit 2-1 boren1:boren0 brown-out reset enable bits (1) 11 = brown-out reset enabled in hardware only (sboren is disabled) 10 = brown-out reset enabled in hardware only and disabled in sleep mode (sboren is disabled) 10 = brown-out reset enabled and controlled by software (sboren is enabled) 10 = brown-out reset disabled in hardware and software bit 0 pwrten : power-up timer enable bit (1) 1 = pwrt disabled 0 = pwrt enabled note 1: the power-up timer is decoupled from brown-out reset, allowing these features to be independently controlled. legend: r = readable bit p = programmable bit u = unimplemented bit, read as ?0? -n = value when device is unprogrammed u = unchanged from programmed state
PIC18F6390/6490/8390/8490 ds39629b-page 284 preliminary ? 2004 microchip technology inc. register 23-3: config2h: configuration register 2 high (byte address 300003h) register 23-4: config3h: configuration register 3 high (byte address 300005h) u-0 u-0 u-0 r/p-1 r/p-1 r/p-1 r/p-1 r/p-1 ? ? ? wdtps3 wdtps2 wdtps1 wdtps0 wdten bit 7 bit 0 bit 7-5 unimplemented: read as ? 0 ? bit 4-1 wdtps3:wdtps0: watchdog timer postscale select bits 1111 = 1:32,768 1110 = 1:16,384 1101 = 1:8,192 1100 = 1:4,096 1011 = 1:2,048 1010 = 1:1,024 1001 = 1:512 1000 = 1:256 0111 = 1:128 0110 = 1:64 0101 = 1:32 0100 = 1:16 0011 = 1:8 0010 = 1:4 0001 = 1:2 0000 = 1:1 bit 0 wdten: watchdog timer enable bit 1 = wdt enabled 0 = wdt disabled (control is placed on the swdten bit) legend: r = readable bit p = programmable bit u = unimplemented bit, read as ?0? -n = value when device is unprogrammed u = unchanged from programmed state r/p-1 u-0 u-0 u-0 u-0 r/p-0 u-0 r/p-1 mclre ? ? ? ?lpt1osc ? ccp2mx bit 7 bit 0 bit 7 mclre: mclr pin enable bit 1 = mclr pin enabled; rg5 input pin disabled 0 = rg5 input pin enabled; mclr disabled bit 6-3 unimplemented: read as ? 0 ? bit 2 lpt1osc: low-power timer 1 oscillator enable bit 1 = timer1 configured for low-power operation 0 = timer1 configured for higher power operation bit 1 unimplemented: read as ? 0 ? bit 0 ccp2mx: ccp2 mux bit 1 = ccp2 input/output is multiplexed with rc1 0 = ccp2 input/output is multiplexed with re7 legend: r = readable bit p = programmable bit u = unimplemented bit, read as ?0? -n = value when device is unprogrammed u = unchanged from programmed state
? 2004 microchip technology inc. preliminary ds39629b-page 285 PIC18F6390/6490/8390/8490 register 23-5: config4l: configuration register 4 low (byte address 300006h) register 23-6: config5l: configuration register 5 low (byte address 300008h) r/p-1 r/p-0 u-0 u-0 u-0 u-0 u-0 r/p-1 debug xinst ? ? ? ? ?stvren bit 7 bit 0 bit 7 debug : background debugger enable bit 1 = background debugger disabled, rb6 and rb7 configured as general purpose i/o pins 0 = background debugger enabled, rb6 and rb7 are dedicated to in-circuit debug bit 6 xinst: extended instruction set enable bit 1 = instruction set extension and indexed addressing mode enabled 0 = instruction set extension and indexed addressing mode disabled (legacy mode) bit 5-1 unimplemented: read as ? 0 ? bit 0 stvren: stack full/underflow reset enable bit 1 = stack full/underflow will cause reset 0 = stack full/underflow will not cause reset legend: r = readable bit c = clearable bit u = unimplemented bit, read as ?0? -n = value when device is unprogrammed u = unchanged from programmed state u-0 u-0 u-0 u-0 u-0 u-0 u-0 r/c-1 ? ? ? ? ? ? ?cp bit 7 bit 0 bit 7-1 unimplemented: read as ? 0 ? bit 0 cp: code protection bit 1 = program memory block (000000-003fffh) not code-protected 0 = program memory block (000000-003fffh) code-protected legend: r = readable bit c = clearable bit u = unimplemented bit, read as ?0? -n = value when device is unprogrammed u = unchanged from programmed state
PIC18F6390/6490/8390/8490 ds39629b-page 286 preliminary ? 2004 microchip technology inc. register 23-7: device id register 1 for PIC18F6390/6490/8390/8490 devices register 23-8: device id register 2 for PIC18F6390/6490/8390/8490 devices rrrrrrrr dev2 dev1 dev0 rev4 rev3 rev2 rev1 rev0 bit 7 bit 0 bit 7-5 dev2:dev0: device id bits 100 = pic18f8390/8490 101 = PIC18F6390/6490 bit 4-0 rev4:rev0: revision id bits these bits are used to indicate the device revision. legend: r = read-only bit p = programmable bit u = unimplemented bit, read as ?0? -n = value when device is unprogrammed u = unchanged from programmed state rrrrrrrr dev10 dev9 dev8 dev7 dev6 dev5 dev4 dev3 bit 7 bit 0 bit 7-0 dev10:dev3: device id bits these bits are used with the dev2:dev0 bits in the device id register 1 to identify the part number. 0000 0110 = pic18f6490/8490 devices 0000 1011 = PIC18F6390/8390 devices note: these values for dev10:dev3 may be shared with other devices. the specific device is always identified by using the entire dev10:dev0 bit sequence. legend: r = read-only bit p = programmable bit u = unimplemented bit, read as ?0? -n = value when device is unprogrammed u = unchanged from programmed state
? 2004 microchip technology inc. preliminary ds39629b-page 287 PIC18F6390/6490/8390/8490 23.2 watchdog timer (wdt) for PIC18F6390/6490/8390/8490 devices, the wdt is driven by the intrc source. when the wdt is enabled, the clock source is also enabled. the nominal wdt period is 4 ms and has the same stability as the intrc oscillator. the 4 ms period of the wdt is multiplied by a 16-bit postscaler. any output of the wdt postscaler is selected by a multiplexer, controlled by bits in configu- ration register 2h. available periods range from 4 ms to 134.2 seconds (2.24 minutes). the wdt and postscaler are cleared when any of the following events occur: a sleep or clrwdt instruction is executed, the ircf bits (osccon<6:4>) are changed, or a clock failure has occurred. 23.2.1 control register register 23-9 shows the wdtcon register. this is a readable and writable register, which contains a control bit that allows software to override the wdt enable configuration bit, but only if the configuration bit has disabled the wdt. figure 23-1: wdt block diagram note 1: the clrwdt and sleep instructions clear the wdt and postscaler counts when executed. 2: changing the setting of the ircf bits (osccon<6:4>) clears the wdt and postscaler counts. 3: when a clrwdt instruction is executed the postscaler count will be cleared. intrc source wdt wake-up reset wdt wdt counter programmable postscaler 1:1 to 1:32,768 enable wdt wdtps<3:0> swdten wdten clrwdt 4 from power reset all device resets sleep intrc control 128 change on ircf bits managed modes
PIC18F6390/6490/8390/8490 ds39629b-page 288 preliminary ? 2004 microchip technology inc. register 23-9: wdtcon: watchdog timer control register table 23-2: summary of watchdog timer registers u-0 u-0 u-0 u-0 u-0 u-0 u-0 r/w-0 ? ? ? ? ? ? ?swdten bit 7 bit 0 bit 7-1 unimplemented : read as ? 0 ? bit 0 swdten: software controlled watchdog timer enable bit 1 = watchdog timer is on 0 = watchdog timer is off note: this bit has no effect if the configuration bit, wdten, is enabled. legend: r = readable bit w = writable bit u = unimplemented bit, read as ?0? -n = value at por name bit 7bit 6bit 5bit 4bit 3bit 2bit 1bit 0 reset values on page rcon ipen sboren ? ri to pd por bor 60 wdtcon ? ? ? ? ? ? ?swdten60 legend: ? = unimplemented, read as ? 0 ?. shaded cells are not used by the watchdog timer.
? 2004 microchip technology inc. preliminary ds39629b-page 289 PIC18F6390/6490/8390/8490 23.3 two-speed start-up the two-speed start-up feature helps to minimize the latency period from oscillator start-up to code execution by allowing the microcontroller to use the intrc oscillator as a clock source until the primary clock source is available. it is enabled by setting the ieso configuration bit. two-speed start-up should be enabled only if the primary oscillator mode is lp, xt, hs or hspll (crystal-based modes). other sources do not require a ost start-up delay; for these, two-speed start-up should be disabled. when enabled, resets and wake-ups from sleep mode cause the device to configure itself to run from the internal oscillator block as the clock source, following the time-out of the power-up timer after a power-on reset is enabled. this allows almost immediate code execution while the primary oscillator starts and the ost is running. once the ost times out, the device automatically switches to pri_run mode. because the osccon register is cleared on reset events, the intosc (or postscaler) clock source is not initially available after a reset event; the intrc clock is used directly at its base frequency. to use a higher clock speed on wake-up, the intosc or postscaler clock sources can be selected to provide a higher clock speed by setting bits, ifrc2:ifrc0, immediately after reset. for wake-ups from sleep, the intosc or postscaler clock sources can be selected by setting the ifrc2:ifrc0 bits prior to entering sleep mode. in all other power managed modes, two-speed start-up is not used. the device will be clocked by the currently selected clock source until the primary clock source becomes available. the setting of the ieso bit is ignored. 23.3.1 special considerations for using two-speed start-up while using the intrc oscillator in two-speed start-up, the device still obeys the normal command sequences for entering power managed modes, including serial sleep instructions (refer to section 3.1.2 ?entering power managed modes? ). in practice, this means that user code can change the scs1:scs0 bit settings or issue sleep instructions before the ost times out. this would allow an application to briefly wake-up, perform routine ?housekeeping? tasks and return to sleep before the device starts to operate from the primary oscillator. user code can also check if the primary clock source is currently providing the device clocking by checking the status of the osts bit (osccon<3>). if the bit is set, the primary oscillator is providing the clock. otherwise, the internal oscillator block is providing the clock during wake-up from reset or sleep mode. figure 23-2: timing transition for two-speed start-up (intosc to hspll) q1 q3 q4 osc1 peripheral program pc pc + 2 intosc pll clock q1 pc + 6 q2 output q3 q4 q1 cpu clock pc + 4 clock counter q2 q2 q3 note 1: t ost = 1024 t osc ; t pll = 2 ms (approx). these intervals are not shown to scale. wake from interrupt event t pll (1) 12 n-1n clock osts bit set transition multiplexer t ost (1)
PIC18F6390/6490/8390/8490 ds39629b-page 290 preliminary ? 2004 microchip technology inc. 23.4 fail-safe clock monitor the fail-safe clock monitor (fscm) allows the microcontroller to continue operation in the event of an external oscillator failure by automatically switching the device clock to the internal oscillator block. the fscm function is enabled by setting the fcmen configuration bit. when fscm is enabled, the intrc oscillator runs at all times to monitor clocks to peripherals and provide a backup clock in the event of a clock failure. clock monitoring (shown in figure 23-3) is accomplished by creating a sample clock signal, which is the intrc out- put divided by 64. this allows ample time between fscm sample clocks for a peripheral clock edge to occur. the peripheral device clock and the sample clock are presented as inputs to the clock monitor latch (cm). the cm is set on the falling edge of the device clock source, but cleared on the rising edge of the sample clock. figure 23-3: fscm block diagram clock failure is tested for on the falling edge of the sample clock. if a sample clock falling edge occurs while cm is still set, a clock failure has been detected (figure 23-4). this causes the following: the fscm generates an oscillator fail interrupt by setting bit oscfif (pir2<7>); the device clock source is switched to the internal oscillator block (osccon is not updated to show the current clock source ? this is the fail-safe condition); and the wdt is reset. during switchover, the postscaler frequency from the internal oscillator block may not be sufficiently stable for timing sensitive applications. in these cases, it may be desirable to select another clock configuration and enter an alternate power managed mode. this can be done to attempt a partial recovery or execute a controlled shut- down. see section 3.1.2 ?entering power managed modes? and section 23.3.1 ?special considerations for using two-speed start-up? for more details. to use a higher clock speed on wake-up, the intosc or postscaler clock sources can be selected to provide a higher clock speed by setting bits, ifrc2:ifrc0, immediately after reset. for wake-ups from sleep, the intosc or postscaler clock sources can be selected by setting the ifrc2:ifrc0 bits prior to entering sleep mode. the fscm will detect failures of the primary or second- ary clock sources only. if the internal oscillator block fails, no failure would be detected, nor would any action be possible. 23.4.1 fscm and the watchdog timer both the fscm and the wdt are clocked by the intrc oscillator. since the wdt operates with a separate divider and counter, disabling the wdt has no effect on the operation of the intrc oscillator when the fscm is enabled. as already noted, the clock source is switched to the intosc clock when a clock failure is detected. depending on the frequency selected by the ircf2:ircf0 bits, this may mean a substantial change in the speed of code execution. if the wdt is enabled with a small prescale value, a decrease in clock speed allows a wdt time-out to occur and a subsequent device reset. for this reason, fail-safe clock events also reset the wdt and postscaler, allowing it to start timing from when execution speed was changed and decreasing the likelihood of an erroneous time-out. 23.4.2 exiting fail-safe operation the fail-safe condition is terminated by either a device reset or by entering a power managed mode. on reset, the controller starts the primary clock source specified in configuration register 1h (with any required start-up delays that are required for the oscil- lator mode, such as the ost or pll timer). the intosc multiplexer provides the device clock until the primary clock source becomes ready (similar to a two- speed start-up). the clock source is then switched to the primary clock (indicated by the osts bit in the osccon register becoming set). the fail-safe clock monitor then resumes monitoring the peripheral clock. the primary clock source may never become ready during start-up. in this case, operation is clocked by the intosc multiplexer. the osccon register will remain in its reset state until a power managed mode is entered. peripheral intrc 64 s c q (32 s) 488 hz (2.048 ms) clock monitor latch (cm) (edge-triggered) clock failure detected source clock q
? 2004 microchip technology inc. preliminary ds39629b-page 291 PIC18F6390/6490/8390/8490 figure 23-4: fscm timing diagram 23.4.3 fscm interrupts in power managed modes by entering a power managed mode, the clock multiplexer selects the clock source selected by the osccon register. fail-safe monitoring of the power managed clock source resumes in the power managed mode. if an oscillator failure occurs during power managed operation, the subsequent events depend on whether or not the oscillator failure interrupt is enabled. if enabled (oscfif = 1 ), code execution will be clocked by the intosc multiplexer. an automatic transition back to the failed clock source will not occur. if the interrupt is disabled, the device will not exit the power managed mode on oscillator failure. instead, the device will continue to operate as before, but clocked by the intosc multiplexer. while in idle mode, subse- quent interrupts will cause the cpu to begin executing instructions while being clocked by the intosc multiplexer. 23.4.4 por or wake from sleep the fscm is designed to detect oscillator failure at any point after the device has exited power-on reset (por) or low-power sleep mode. when the primary device clock is ec, rc or intrc modes, monitoring can begin immediately following these events. for oscillator modes involving a crystal or resonator (hs, hspll, lp or xt), the situation is somewhat different. since the oscillator may require a start-up time considerably longer than the fcsm sample clock time, a false clock failure may be detected. to prevent this, the internal oscillator block is automatically con- figured as the device clock and functions until the primary clock is stable (the ost and pll timers have timed out). this is identical to two-speed start-up mode. once the primary clock is stable, the intrc returns to its role as the fscm source. as noted in section 23.3.1 ?special considerations for using two-speed start-up? , it is also possible to select another clock configuration and enter an alternate power managed mode while waiting for the primary clock to become stable. when the new powered managed mode is selected, the primary clock is disabled. oscfif cm output device clock output sample clock failure detected oscillator failure note: the device clock is normally at a mu ch higher frequency than the sample clock. the relative frequencies in this example have been chosen for clarity. (q ) cm test cm test cm test note: the same logic that prevents false oscillator failure interrupts on por, or wake from sleep, will also prevent the detection of the oscillator?s failure to start at all following these events. this can be avoided by monitoring the osts bit and using a timing routine to determine if the oscillator is taking too long to start. even so, no oscillator failure interrupt will be flagged.
PIC18F6390/6490/8390/8490 ds39629b-page 292 preliminary ? 2004 microchip technology inc. 23.5 program verification and code protection the overall structure of the code protection on the PIC18F6390/6490/8390/8490 flash devices differs from previous pic18 devices. for all devices in the pic18f6x90/8x90 family, the user program memory is made of a single block. figure 23-5 shows the program memory organization for individual devices. code protection for this block is controlled by a single bit, cp (config5l<0>). the cp bit inhibits external reads from and writes to the entire program memory space. it has no direct effect in normal execution mode. 23.5.1 reading program memory and other locations the program memory may be read to any location using the table read instructions. the device id and the configuration registers may be read with the table read instructions. 23.5.2 configuration register protection the configuration registers can only be written via icsp using an external programmer. no separate protection bit is associated with them. figure 23-5: code-protected program memory for PIC18F6390/6490/8390/8490 table 23-3: summary of code protection registers memory size/device block code protection controlled by: 8kbytes (PIC18F6390/8390) address range 16 kbytes (pic18f6490/8490) address range program memory block 000000h 001fffh program memory block 000000h 003fffh cp, ebtr unimplemented read ? 0 ?s 002000h 1fffffh unimplemented read ? 0 ?s 004000h 1fffffh (unimplemented memory space) file name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 300008h config5l ? ? ? ? ? ? ?cp legend: shaded cells are unimplemented.
? 2004 microchip technology inc. preliminary ds39629b-page 293 PIC18F6390/6490/8390/8490 23.6 id locations eight memory locations (200000h-200007h) are designated as id locations, where the user can store checksum or other code identification numbers. these locations are readable during normal execution through the tblrd instruction; during program/verify, these locations are readable and writable. the id locations can be read when the device is code-protected. 23.7 in-circuit serial programming PIC18F6390/6490/8390/8490 microcontrollers can be serially programmed while in the end application circuit. this is simply done with two lines for clock and data and three other lines for power, ground and the programming voltage. this allows customers to manufacture boards with unprogrammed devices and then program the microcontroller just before shipping the product. this also allows the most recent firmware or a custom firmware to be programmed. 23.8 in-circuit debugger when the debug configuration bit is programmed to a ? 0 ?, the in-circuit debugger functionality is enabled. this function allows simple debugging functions when used with mplab ? ide. when the microcontroller has this feature enabled, some resources are not available for general use. table 23-4 shows which resources are required by the background debugger. table 23-4: debugger resources to use the in-circuit debugger function of the micro- controller, the design must implement in-circuit serial programming connections to mclr /v pp , v dd , v ss , rb7 and rb6. this will interface to the in-circuit debugger module available from microchip or one of the third party development tool companies. i/o pins: rb6, rb7 stack: 2 levels program memory: 512 bytes data memory: 10 bytes
PIC18F6390/6490/8390/8490 ds39629b-page 294 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 295 PIC18F6390/6490/8390/8490 24.0 instruction set summary pic18fxx90 devices incorporate the standard set of 75 pic18 core instructions, as well as an extended set of 8 new instructions for the optimization of code that is recursive or that utilizes a software stack. the extended set is discussed later in this section. 24.1 standard instruction set the standard pic18 instruction set adds many enhancements to the previous picmicro ? instruction sets, while maintaining an easy migration from these picmicro instruction sets. most instructions are a single program memory word (16 bits), but there are four instructions that require two program memory locations. each single-word instruction is a 16-bit word divided into an opcode, which specifies the instruction type and one or more operands, which further specify the operation of the instruction. the instruction set is highly orthogonal and is grouped into four basic categories: byte-oriented operations bit-oriented operations literal operations control operations the pic18 instruction set summary in table 24-2 lists byte-oriented , bit-oriented , literal and control operations. table 24-1 shows the opcode field descriptions. most byte-oriented instructions have three operands: 1. the file register (specified by ?f?) 2. the destination of the result (specified by ?d?) 3. the accessed memory (specified by ?a?) the file register designator ?f? specifies which file register is to be used by the instruction. the destination designator ?d? specifies where the result of the opera- tion is to be placed. if ?d? is zero, the result is placed in the wreg register. if ?d? is one, the result is placed in the file register specified in the instruction. all bit-oriented instructions have three operands: 1. the file register (specified by ?f?) 2. the bit in the file register (specified by ?b?) 3. the accessed memory (specified by ?a?) the bit field designator ?b? selects the number of the bit affected by the operation, while the file register desig- nator ?f? represents the number of the file in which the bit is located. the literal instructions may use some of the following operands: a literal value to be loaded into a file register (specified by ?k?) the desired fsr register to load the literal value into (specified by ?f?) no operand required (specified by ???) the control instructions may use some of the following operands: a program memory address (specified by ?n?) the mode of the call or return instructions (specified by ?s?) the mode of the table read and table write instructions (specified by ?m?) no operand required (specified by ???) all instructions are a single word, except for four double-word instructions. these instructions were made double-word to contain the required information in 32 bits. in the second word, the 4 msbs are ? 1 ?s. if this second word is executed as an instruction (by itself), it will execute as a nop . all single-word instructions are executed in a single instruction cycle, unless a conditional test is true or the program counter is changed as a result of the instruc- tion. in these cases, the execution takes two instruction cycles with the additional instruction cycle(s) executed as a nop . the double-word instructions execute in two instruction cycles. one instruction cycle consists of four oscillator periods. thus, for an oscillator frequency of 4 mhz, the normal instruction execution time is 1 s. if a conditional test is true, or the program counter is changed as a result of an instruction, the instruction execution time is 2 s. two-word branch instructions (if true) would take 3 s. figure 24-1 shows the general formats that the instruc- tions can have. all examples use the convention ?nnh? to represent a hexadecimal number. the instruction set summary, shown in table 24-2, lists the standard instructions recognized by the microchip mpasm tm assembler. section 24.1.1 ?standard instruction set? provides a description of each instruction.
PIC18F6390/6490/8390/8490 ds39629b-page 296 preliminary ? 2004 microchip technology inc. table 24-1: opcode field descriptions field description a ram access bit a = 0 : ram location in access ram (bsr register is ignored) a = 1 : ram bank is specified by bsr register bbb bit address within an 8-bit file register (0 to 7). bsr bank select register. used to select the current ram bank. c, dc, z, ov, n alu status bits: c arry, d igit c arry, z ero, ov erflow, n egative. d destination select bit d = 0 : store result in wreg d = 1 : store result in file register f dest destination: either the wreg register or the specified register file location. f 8-bit register file address (00h to ffh), or 2-bit fsr designator (0h to 3h). f s 12-bit register file address (000h to ff fh). this is the source address. f d 12-bit register file address (000h to fffh). this is the destination address. gie global interrupt enable bit. k literal field, constant data or label (may be either an 8-bit, 12-bit or a 20-bit value) label label name mm the mode of the tblptr register for the table read and table write instructions. only used with table read and table write instructions: * no change to register (such as tblptr with table reads and writes) *+ post-increment register (such as tblptr with table reads and writes) *- post-decrement register (such as tblptr with table reads and writes) +* pre-increment register (such as tb lptr with table reads and writes) n the relative address (2?s complement number) for relative branch instructions or the direct address for call/branch and return instructions pc program counter. pcl program counter low byte. pch program counter high byte. pclath program counter high byte latch. pclatu program counter upper byte latch. pd power-down bit. prodh product of multiply high byte. prodl product of multiply low byte. s fast call/return mode select bit s = 0 : do not update into/from shadow registers s = 1 : certain registers loaded into/from shadow registers (fast mode) tblptr 21-bit table pointer (points to a program memory location). tablat 8-bit table latch. to time-out bit. tos top-of-stack. u unused or unchanged. wdt watchdog timer. wreg working register (accumulator). x don?t care (? 0 ? or ? 1 ?). the assembler will generate code with x = 0 . it is the recommended form of use for compatibility with all microchip software tools. z s 7-bit offset value for indirect addr essing of register files (source). z d 7-bit offset value for indirect addressing of register files (destination). { } optional argument. [text] indicates an indexed address. (text) the contents of text . [expr] specifies bit n of the register indicated by the pointer expr . assigned to. < > register bit field. in the set of. italics user defined term (font is courier).
? 2004 microchip technology inc. preliminary ds39629b-page 297 PIC18F6390/6490/8390/8490 figure 24-1: general format for instructions byte-oriented file register operations 15 10 9 8 7 0 d = 0 for result destination to be wreg register opcode d a f (file #) d = 1 for result destination to be file register (f) a = 0 to force access bank bit-oriented file register operations 15 12 11 9 8 7 0 opcode b (bit #) a f (file #) b = 3-bit position of bit in file register (f) literal operations 15 8 7 0 opcode k (literal) k = 8-bit immediate value byte to byte move operations (2-word) 15 12 11 0 opcode f (source file #) call, goto and branch operations 15 8 7 0 opcode n<7:0> (literal) n = 20-bit immediate value a = 1 for bsr to select bank f = 8-bit file register address a = 0 to force access bank a = 1 for bsr to select bank f = 8-bit file register address 15 12 11 0 1111 n<19:8> (literal) 15 12 11 0 1111 f (destination file #) f = 12-bit file register address control operations example instruction addwf myreg, w, b movff myreg1, myreg2 bsf myreg, bit, b movlw 7fh goto label 15 8 7 0 opcode n<7:0> (literal) 15 12 11 0 1111 n<19:8> (literal) call myfunc 15 11 10 0 opcode n<10:0> (literal) s = fast bit bra myfunc 15 8 7 0 opcode n<7:0> (literal) bc myfunc s
PIC18F6390/6490/8390/8490 ds39629b-page 298 preliminary ? 2004 microchip technology inc. table 24-2: pic18fxxxx instruction set mnemonic, operands description cycles 16-bit instruction word status affected notes msb lsb byte-oriented operations addwf addwfc andwf clrf comf cpfseq cpfsgt cpfslt decf decfsz dcfsnz incf incfsz infsnz iorwf movf movff movwf mulwf negf rlcf rlncf rrcf rrncf setf subfwb subwf subwfb swapf tstfsz xorwf f, d, a f, d, a f, d, a f, a f, d, a f, a f, a f, a f, d, a f, d, a f, d, a f, d, a f, d, a f, d, a f, d, a f, d, a f s , f d f, a f, a f, a f, d, a f, d, a f, d, a f, d, a f, a f, d, a f, d, a f, d, a f, d, a f, a f, d, a add wreg and f add wreg and carry bit to f and wreg with f clear f complement f compare f with wreg, skip = compare f with wreg, skip > compare f with wreg, skip < decrement f decrement f, skip if 0 decrement f, skip if not 0 increment f increment f, skip if 0 increment f, skip if not 0 inclusive or wreg with f move f move f s (source) to 1st word f d (destination) 2nd word move wreg to f multiply wreg with f negate f rotate left f through carry rotate left f (no carry) rotate right f through carry rotate right f (no carry) set f subtract f from wreg with borrow subtract wreg from f subtract wreg from f with borrow swap nibbles in f test f, skip if 0 exclusive or wreg with f 1 1 1 1 1 1 (2 or 3) 1 (2 or 3) 1 (2 or 3) 1 1 (2 or 3) 1 (2 or 3) 1 1 (2 or 3) 1 (2 or 3) 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 (2 or 3) 1 0010 0010 0001 0110 0001 0110 0110 0110 0000 0010 0100 0010 0011 0100 0001 0101 1100 1111 0110 0000 0110 0011 0100 0011 0100 0110 0101 0101 0101 0011 0110 0001 01da 00da 01da 101a 11da 001a 010a 000a 01da 11da 11da 10da 11da 10da 00da 00da ffff ffff 111a 001a 110a 01da 01da 00da 00da 100a 01da 11da 10da 10da 011a 10da ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff c, dc, z, ov, n c, dc, z, ov, n z, n z z, n none none none c, dc, z, ov, n none none c, dc, z, ov, n none none z, n z, n none none none c, dc, z, ov, n c, z, n z, n c, z, n z, n none c, dc, z, ov, n c, dc, z, ov, n c, dc, z, ov, n none none z, n 1, 2 1, 2 1,2 2 1, 2 4 4 1, 2 1, 2, 3, 4 1, 2, 3, 4 1, 2 1, 2, 3, 4 4 1, 2 1, 2 1 1, 2 1, 2 1, 2 1, 2 4 1, 2 note 1: when a port register is modified as a function of itself (e.g., movf portb, 1, 0 ), the value used will be that value present on the pins themselves. for example, if the data latch is ? 1 ? for a pin configured as input and is driven low by an external device, the data will be written back with a ? 0 ?. 2: if this instruction is executed on the tmr0 register (and where applicable, ?d? = 1 ), the prescaler will be cleared if assigned. 3: if program counter (pc) is modified or a conditional test is true, the instruction requires two cycles. the second cycle is executed as a nop . 4: some instructions are two-word instructions. the second word of these instructions will be executed as a nop unless the first word of the instruction retrieves the information embedded in these 16 bits. this ensures that all program memory locations have a valid instruction. 5: if the table write starts the write cycle to internal memory, the write will continue until terminated.
? 2004 microchip technology inc. preliminary ds39629b-page 299 PIC18F6390/6490/8390/8490 bit-oriented operations bcf bsf btfsc btfss btg f, b, a f, b, a f, b, a f, b, a f, d, a bit clear f bit set f bit test f, skip if clear bit test f, skip if set bit toggle f 1 1 1 (2 or 3) 1 (2 or 3) 1 1001 1000 1011 1010 0111 bbba bbba bbba bbba bbba ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff none none none none none 1, 2 1, 2 3, 4 3, 4 1, 2 control operations bc bn bnc bnn bnov bnz bov bra bz call clrwdt daw goto nop nop pop push rcall reset retfie retlw return sleep n n n n n n n n n n, s ? ? n ? ? ? ? n s k s ? branch if carry branch if negative branch if not carry branch if not negative branch if not overflow branch if not zero branch if overflow branch unconditionally branch if zero call subroutine1st word 2nd word clear watchdog timer decimal adjust wreg go to address 1st word 2nd word no operation no operation pop top of return stack (tos) push top of return stack (tos) relative call software device reset return from interrupt enable return with literal in wreg return from subroutine go into standby mode 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 2 1 (2) 2 1 1 2 1 1 1 1 2 1 2 2 2 1 1110 1110 1110 1110 1110 1110 1110 1101 1110 1110 1111 0000 0000 1110 1111 0000 1111 0000 0000 1101 0000 0000 0000 0000 0000 0010 0110 0011 0111 0101 0001 0100 0nnn 0000 110s kkkk 0000 0000 1111 kkkk 0000 xxxx 0000 0000 1nnn 0000 0000 1100 0000 0000 nnnn nnnn nnnn nnnn nnnn nnnn nnnn nnnn nnnn kkkk kkkk 0000 0000 kkkk kkkk 0000 xxxx 0000 0000 nnnn 1111 0001 kkkk 0001 0000 nnnn nnnn nnnn nnnn nnnn nnnn nnnn nnnn nnnn kkkk kkkk 0100 0111 kkkk kkkk 0000 xxxx 0110 0101 nnnn 1111 000s kkkk 001s 0011 none none none none none none none none none none to , pd c none none none none none none all gie/gieh, peie/giel none none to , pd 4 table 24-2: pic18fxxxx instruction set (continued) mnemonic, operands description cycles 16-bit instruction word status affected notes msb lsb note 1: when a port register is modified as a function of itself (e.g., movf portb, 1, 0 ), the value used will be that value present on the pins themselves. for example, if the data latch is ? 1 ? for a pin configured as input and is driven low by an external device, the data will be written back with a ? 0 ?. 2: if this instruction is executed on the tmr0 register (and where applicable, ?d? = 1 ), the prescaler will be cleared if assigned. 3: if program counter (pc) is modified or a conditional test is true, the instruction requires two cycles. the second cycle is executed as a nop . 4: some instructions are two-word instructions. the second word of these instructions will be executed as a nop unless the first word of the instruction retrieves the information embedded in these 16 bits. this ensures that all program memory locations have a valid instruction. 5: if the table write starts the write cycle to internal memory, the write will continue until terminated.
PIC18F6390/6490/8390/8490 ds39629b-page 300 preliminary ? 2004 microchip technology inc. literal operations addlw andlw iorlw lfsr movlb movlw mullw retlw sublw xorlw k k k f, k k k k k k k add literal and wreg and literal with wreg inclusive or literal with wreg move literal (12-bit) 2nd word to fsr(f) 1st word move literal to bsr<3:0> move literal to wreg multiply literal with wreg return with literal in wreg subtract wreg from literal exclusive or literal with wreg 1 1 1 2 1 1 1 2 1 1 0000 0000 0000 1110 1111 0000 0000 0000 0000 0000 0000 1111 1011 1001 1110 0000 0001 1110 1101 1100 1000 1010 kkkk kkkk kkkk 00ff kkkk 0000 kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk kkkk c, dc, z, ov, n z, n z, n none none none none none c, dc, z, ov, n z, n data memory ? program memory operations tblrd* tblrd*+ tblrd*- tblrd+* tblwt* tblwt*+ tblwt*- tblwt+* table read table read with post-increment table read with post-decrement table read with pre-increment table write table write with post-increment table write with post-decrement table write with pre-increment 2 2 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 1000 1001 1010 1011 1100 1101 1110 1111 none none none none none none none none 5 5 5 5 table 24-2: pic18fxxxx instruction set (continued) mnemonic, operands description cycles 16-bit instruction word status affected notes msb lsb note 1: when a port register is modified as a function of itself (e.g., movf portb, 1, 0 ), the value used will be that value present on the pins themselves. for example, if the data latch is ? 1 ? for a pin configured as input and is driven low by an external device, the data will be written back with a ? 0 ?. 2: if this instruction is executed on the tmr0 register (and where applicable, ?d? = 1 ), the prescaler will be cleared if assigned. 3: if program counter (pc) is modified or a conditional test is true, the instruction requires two cycles. the second cycle is executed as a nop . 4: some instructions are two-word instructions. the second word of these instructions will be executed as a nop unless the first word of the instruction retrieves the information embedded in these 16 bits. this ensures that all program memory locations have a valid instruction. 5: if the table write starts the write cycle to internal memory, the write will continue until terminated.
? 2004 microchip technology inc. preliminary ds39629b-page 301 PIC18F6390/6490/8390/8490 24.1.1 standard instruction set addlw add literal to w syntax: addlw k operands: 0 k 255 operation: (w) + k w status affected: n, ov, c, dc, z encoding: 0000 1111 kkkk kkkk description: the contents of w are added to the 8-bit literal ?k? and the result is placed in w. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read literal ?k? process data write to w example: addlw 15h before instruction w = 10h after instruction w = 25h addwf add w to f syntax: addwf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (w) + (f) dest status affected: n, ov, c, dc, z encoding: 0010 01da ffff ffff description: add w to register ?f?. if ?d? is ? 0 ?, the result is stored in w. if ?d? is ? 1 ?, the result is stored back in register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: addwf reg, 0, 0 before instruction w = 17h reg = 0c2h after instruction w = 0d9h reg = 0c2h note: all pic18 instructions may take an optional label ar gument preceding the instruction mnemonic for use in symbolic addressing. if a label is used, the instruct ion format then becomes: {label} instruction argument(s).
PIC18F6390/6490/8390/8490 ds39629b-page 302 preliminary ? 2004 microchip technology inc. addwfc add w and carry bit to f syntax: addwfc f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (w) + (f) + (c) dest status affected: n,ov, c, dc, z encoding: 0010 00da ffff ffff description: add w, the carry flag and data memory location ?f?. if ?d? is ? 0 ?, the result is placed in w. if ?d? is ? 1 ?, the result is placed in data memory location ?f?. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: addwfc reg, 0, 1 before instruction carry bit = 1 reg = 02h w=4dh after instruction carry bit = 0 reg = 02h w = 50h andlw and literal with w syntax: andlw k operands: 0 k 255 operation: (w) .and. k w status affected: n, z encoding: 0000 1011 kkkk kkkk description: the contents of w are anded with the 8-bit literal ?k?. the result is placed in w. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read literal ?k? process data write to w example: andlw 05fh before instruction w=a3h after instruction w = 03h
? 2004 microchip technology inc. preliminary ds39629b-page 303 PIC18F6390/6490/8390/8490 andwf and w with f syntax: andwf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (w) .and. (f) dest status affected: n, z encoding: 0001 01da ffff ffff description: the contents of w are and?ed with register ?f?. if ?d? is ? 0 ?, the result is stored in w. if ?d? is ? 1 ?, the result is stored back in register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: andwf reg, 0, 0 before instruction w = 17h reg = c2h after instruction w = 02h reg = c2h bc branch if carry syntax: bc n operands: -128 n 127 operation: if carry bit is ? 1 ? (pc) + 2 + 2n pc status affected: none encoding: 1110 0010 nnnn nnnn description: if the carry bit is ? 1 ?, then the program will branch. the 2?s complement number ?2n? is added to the pc. since the pc will have incremented to fetch the next instruction, the new address will be pc + 2 + 2n. this instruction is then a two-cycle instruction. words: 1 cycles: 1(2) q cycle activity: if jump: q1 q2 q3 q4 decode read literal ?n? process data write to pc no operation no operation no operation no operation if no jump: q1 q2 q3 q4 decode read literal ?n? process data no operation example: here bc 5 before instruction pc = address (here) after instruction if carry = 1; pc = address (here + 12) if carry = 0; pc = address (here + 2)
PIC18F6390/6490/8390/8490 ds39629b-page 304 preliminary ? 2004 microchip technology inc. bcf bit clear f syntax: bcf f, b {,a} operands: 0 f 255 0 b 7 a [0,1] operation: 0 f status affected: none encoding: 1001 bbba ffff ffff description: bit ?b? in register ?f? is cleared. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addr essing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write register ?f? example: bcf flag_reg, 7, 0 before instruction flag_reg = c7h after instruction flag_reg = 47h bn branch if negative syntax: bn n operands: -128 n 127 operation: if negative bit is ? 1 ? (pc) + 2 + 2n pc status affected: none encoding: 1110 0110 nnnn nnnn description: if the negative bit is ? 1 ?, then the program will branch. the 2?s complement number ?2n? is added to the pc. since the pc will have incremented to fetch the next instruction, the new address will be pc + 2 + 2n. this instruction is then a two-cycle instruction. words: 1 cycles: 1(2) q cycle activity: if jump: q1 q2 q3 q4 decode read literal ?n? process data write to pc no operation no operation no operation no operation if no jump: q1 q2 q3 q4 decode read literal ?n? process data no operation example: here bn jump before instruction pc = address (here) after instruction if negative = 1; pc = address (jump) if negative = 0; pc = address (here + 2)
? 2004 microchip technology inc. preliminary ds39629b-page 305 PIC18F6390/6490/8390/8490 bnc branch if not carry syntax: bnc n operands: -128 n 127 operation: if carry bit is ? 0 ? (pc) + 2 + 2n pc status affected: none encoding: 1110 0011 nnnn nnnn description: if the carry bit is ? 0 ?, then the program will branch. the 2?s complement number ?2n? is added to the pc. since the pc will have incremented to fetch the next instruction, the new address will be pc + 2 + 2n. this instruction is then a two-cycle instruction. words: 1 cycles: 1(2) q cycle activity: if jump: q1 q2 q3 q4 decode read literal ?n? process data write to pc no operation no operation no operation no operation if no jump: q1 q2 q3 q4 decode read literal ?n? process data no operation example: here bnc jump before instruction pc = address (here) after instruction if carry = 0; pc = address (jump) if carry = 1; pc = address (here + 2) bnn branch if not negative syntax: bnn n operands: -128 n 127 operation: if negative bit is ? 0 ? (pc) + 2 + 2n pc status affected: none encoding: 1110 0111 nnnn nnnn description: if the negative bit is ? 0 ?, then the program will branch. the 2?s complement number ?2n? is added to the pc. since the pc will have incremented to fetch the next instruction, the new address will be pc + 2 + 2n. this instruction is then a two-cycle instruction. words: 1 cycles: 1(2) q cycle activity: if jump: q1 q2 q3 q4 decode read literal ?n? process data write to pc no operation no operation no operation no operation if no jump: q1 q2 q3 q4 decode read literal ?n? process data no operation example: here bnn jump before instruction pc = address (here) after instruction if negative = 0; pc = address (jump) if negative = 1; pc = address (here + 2)
PIC18F6390/6490/8390/8490 ds39629b-page 306 preliminary ? 2004 microchip technology inc. bnov branch if not overflow syntax: bnov n operands: -128 n 127 operation: if overflow bit is ? 0 ? (pc) + 2 + 2n pc status affected: none encoding: 1110 0101 nnnn nnnn description: if the overflow bit is ? 0 ?, then the program will branch. the 2?s complement number ?2n? is added to the pc. since the pc will have incremented to fetch the next instruction, the new address will be pc + 2 + 2n. this instruction is then a two-cycle instruction. words: 1 cycles: 1(2) q cycle activity: if jump: q1 q2 q3 q4 decode read literal ?n? process data write to pc no operation no operation no operation no operation if no jump: q1 q2 q3 q4 decode read literal ?n? process data no operation example: here bnov jump before instruction pc = address (here) after instruction if overflow = 0; pc = address (jump) if overflow = 1; pc = address (here + 2) bnz branch if not zero syntax: bnz n operands: -128 n 127 operation: if zero bit is ? 0 ? (pc) + 2 + 2n pc status affected: none encoding: 1110 0001 nnnn nnnn description: if the zero bit is ? 0 ?, then the program will branch. the 2?s complement number ?2n? is added to the pc. since the pc will have incremented to fetch the next instruction, the new address will be pc + 2 + 2n. this instruction is then a two-cycle instruction. words: 1 cycles: 1(2) q cycle activity: if jump: q1 q2 q3 q4 decode read literal ?n? process data write to pc no operation no operation no operation no operation if no jump: q1 q2 q3 q4 decode read literal ?n? process data no operation example: here bnz jump before instruction pc = address (here) after instruction if zero = 0; pc = address (jump) if zero = 1; pc = address (here + 2)
? 2004 microchip technology inc. preliminary ds39629b-page 307 PIC18F6390/6490/8390/8490 bra unconditional branch syntax: bra n operands: -1024 n 1023 operation: (pc) + 2 + 2n pc status affected: none encoding: 1101 0nnn nnnn nnnn description: add the 2?s complement number ?2n? to the pc. since the pc will have incremented to fetch the next instruction, the new address will be pc + 2 + 2n. this instruction is a two-cycle instruction. words: 1 cycles: 2 q cycle activity: q1 q2 q3 q4 decode read literal ?n? process data write to pc no operation no operation no operation no operation example: here bra jump before instruction pc = address (here) after instruction pc = address (jump) bsf bit set f syntax: bsf f, b {,a} operands: 0 f 255 0 b 7 a [0,1] operation: 1 f status affected: none encoding: 1000 bbba ffff ffff description: bit ?b? in register ?f? is set. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write register ?f? example: bsf flag_reg, 7, 1 before instruction flag_reg = 0ah after instruction flag_reg = 8ah
PIC18F6390/6490/8390/8490 ds39629b-page 308 preliminary ? 2004 microchip technology inc. btfsc bit test file, skip if clear syntax: btfsc f, b {,a} operands: 0 f 255 0 b 7 a [0,1] operation: skip if (f) = 0 status affected: none encoding: 1011 bbba ffff ffff description: if bit ?b? in register ?f? is ? 0 ?, then the next instruction is skipped. if bit ?b? is ? 0 ?, then the next instruction fetched during the current instruction execution is discarded and a nop is executed instead, making this a two-cycle instruction. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1(2) note: 3 cycles if skip and followed by a 2-word instruction. q cycle activity: q1 q2 q3 q4 decode read register ?f? process data no operation if skip: q1 q2 q3 q4 no operation no operation no operation no operation if skip and followed by 2-word instruction: q1 q2 q3 q4 no operation no operation no operation no operation no operation no operation no operation no operation example: here false true btfsc : : flag, 1, 0 before instruction pc = address (here) after instruction if flag<1> = 0; pc = address (true) if flag<1> = 1; pc = address (false) btfss bit test file, skip if set syntax: btfss f, b {,a} operands: 0 f 255 0 b < 7 a [0,1] operation: skip if (f) = 1 status affected: none encoding: 1010 bbba ffff ffff description: if bit ?b? in register ?f? is ? 1 ?, then the next instruction is skipped. if bit ?b? is ? 1 ?, then the next instruction fetched during the current instruction execution is discarded and a nop is executed instead, making this a two-cycle instruction. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1(2) note: 3 cycles if skip and followed by a 2-word instruction. q cycle activity: q1 q2 q3 q4 decode read register ?f? process data no operation if skip: q1 q2 q3 q4 no operation no operation no operation no operation if skip and followed by 2-word instruction: q1 q2 q3 q4 no operation no operation no operation no operation no operation no operation no operation no operation example: here false true btfss : : flag, 1, 0 before instruction pc = address (here) after instruction if flag<1> = 0; pc = address (false) if flag<1> = 1; pc = address (true)
? 2004 microchip technology inc. preliminary ds39629b-page 309 PIC18F6390/6490/8390/8490 btg bit toggle f syntax: btg f, b {,a} operands: 0 f 255 0 b < 7 a [0,1] operation: (f ) f status affected: none encoding: 0111 bbba ffff ffff description: bit ?b? in data memory location ?f? is inverted. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write register ?f? example: btg portc, 4, 0 before instruction: portc = 0111 0101 [75h] after instruction: portc = 0110 0101 [65h] bov branch if overflow syntax: bov n operands: -128 n 127 operation: if overflow bit is ? 1 ? (pc) + 2 + 2n pc status affected: none encoding: 1110 0100 nnnn nnnn description: if the overflow bit is ? 1 ?, then the program will branch. the 2?s complement number ?2n? is added to the pc. since the pc will have incremented to fetch the next instruction, the new address will be pc + 2 + 2n. this instruction is then a two-cycle instruction. words: 1 cycles: 1(2) q cycle activity: if jump: q1 q2 q3 q4 decode read literal ?n? process data write to pc no operation no operation no operation no operation if no jump: q1 q2 q3 q4 decode read literal ?n? process data no operation example: here bov jump before instruction pc = address (here) after instruction if overflow = 1; pc = address (jump) if overflow = 0; pc = address (here + 2)
PIC18F6390/6490/8390/8490 ds39629b-page 310 preliminary ? 2004 microchip technology inc. bz branch if zero syntax: bz n operands: -128 n 127 operation: if zero bit is ? 1 ? (pc) + 2 + 2n pc status affected: none encoding: 1110 0000 nnnn nnnn description: if the zero bit is ? 1 ?, then the program will branch. the 2?s complement number ?2n? is added to the pc. since the pc will have incremented to fetch the next instruction, the new address will be pc + 2 + 2n. this instruction is then a two-cycle instruction. words: 1 cycles: 1(2) q cycle activity: if jump: q1 q2 q3 q4 decode read literal ?n? process data write to pc no operation no operation no operation no operation if no jump: q1 q2 q3 q4 decode read literal ?n? process data no operation example: here bz jump before instruction pc = address (here) after instruction if zero = 1; pc = address (jump) if zero = 0; pc = address (here + 2) call subroutine call syntax: call k {,s} operands: 0 k 1048575 s [0,1] operation: (pc) + 4 tos, k pc<20:1>, if s = 1 (w) ws, (status) statuss, (bsr) bsrs status affected: none encoding: 1st word (k<7:0>) 2nd word(k<19:8>) 1110 1111 110s k 19 kkk k 7 kkk kkkk kkkk 0 kkkk 8 description: subroutine call of entire 2-mbyte memory range. first, return address (pc + 4) is pushed onto the return stack. if ?s? = 1 , the w, status and bsr registers are also pushed into their respective shadow registers, ws, statuss and bsrs. if ?s? = 0 , no update occurs (default). then, the 20-bit value ?k? is loaded into pc<20:1>. call is a two-cycle instruction. words: 2 cycles: 2 q cycle activity: q1 q2 q3 q4 decode read literal ?k?<7:0>, push pc to stack read literal ?k?<19:8>, write to pc no operation no operation no operation no operation example: here call there,1 before instruction pc = address (here) after instruction pc = address (there) tos = address (here + 4) ws = w bsrs = bsr statuss= status
? 2004 microchip technology inc. preliminary ds39629b-page 311 PIC18F6390/6490/8390/8490 clrf clear f syntax: clrf f {,a} operands: 0 f 255 a [0,1] operation: 000h f 1 z status affected: z encoding: 0110 101a ffff ffff description: clears the contents of the specified register. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write register ?f? example: clrf flag_reg,1 before instruction flag_reg = 5ah after instruction flag_reg = 00h clrwdt clear watchdog timer syntax: clrwdt operands: none operation: 000h wdt, 000h wdt postscaler, 1 to, 1 pd status affected: to , pd encoding: 0000 0000 0000 0100 description: clrwdt instruction resets the watchdog timer. it also resets the postscaler of the wdt. status bits to and pd are set. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode no operation process data no operation example: clrwdt before instruction wdt counter = ? after instruction wdt counter = 00h wdt postscaler = 0 to =1 pd =1
PIC18F6390/6490/8390/8490 ds39629b-page 312 preliminary ? 2004 microchip technology inc. comf complement f syntax: comf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: dest status affected: n, z encoding: 0001 11da ffff ffff description: the contents of register ?f? are complemented. if ?d? is ? 1 ?, the result is stored in w. if ?d? is ? 0 ?, the result is stored back in register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: comf reg, 0, 0 before instruction reg = 13h after instruction reg = 13h w=ech ( f) cpfseq compare f with w, skip if f = w syntax: cpfseq f {,a} operands: 0 f 255 a [0,1] operation: (f) ? (w), skip if (f) = (w) (unsigned comparison) status affected: none encoding: 0110 001a ffff ffff description: compares the contents of data memory location ?f? to the contents of w by performing an unsigned subtraction. if ?f? = w , then the fetched instruction is discarded and a nop is executed instead, making this a two-cycle instruction. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 0 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1(2) note: 3 cycles if skip and followed by a 2-word instruction. q cycle activity: q1 q2 q3 q4 decode read register ?f? process data no operation if skip: q1 q2 q3 q4 no operation no operation no operation no operation if skip and followed by 2-word instruction: q1 q2 q3 q4 no operation no operation no operation no operation no operation no operation no operation no operation example: here cpfseq reg, 0 nequal : equal : before instruction pc address = here w=? reg = ? after instruction if reg = w; pc = address (equal) if reg w; pc = address (nequal)
? 2004 microchip technology inc. preliminary ds39629b-page 313 PIC18F6390/6490/8390/8490 cpfsgt compare f with w, skip if f > w syntax: cpfsgt f {,a} operands: 0 f 255 a [0,1] operation: (f) ? ( w), skip if (f) > (w) (unsigned comparison) status affected: none encoding: 0110 010a ffff ffff description: compares the contents of data memory location ?f? to the contents of the w by performing an unsigned subtraction. if the contents of ?f? are greater than the contents of wreg , then the fetched instruction is discarded and a nop is executed instead, making this a two-cycle instruction. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1(2) note: 3 cycles if skip and followed by a 2-word instruction. q cycle activity: q1 q2 q3 q4 decode read register ?f? process data no operation if skip: q1 q2 q3 q4 no operation no operation no operation no operation if skip and followed by 2-word instruction: q1 q2 q3 q4 no operation no operation no operation no operation no operation no operation no operation no operation example: here cpfsgt reg, 0 ngreater : greater : before instruction pc = address (here) w= ? after instruction if reg > w; pc = address (greater) if reg w; pc = address (ngreater) cpfslt compare f with w, skip if f < w syntax: cpfslt f {,a} operands: 0 f 255 a [0,1] operation: (f) ? ( w), skip if (f) < (w) (unsigned comparison) status affected: none encoding: 0110 000a ffff ffff description: compares the contents of data memory location ?f? to the contents of w by performing an unsigned subtraction. if the contents of ?f? are less than the contents of w, then the fetched instruction is discarded and a nop is executed instead, making this a two-cycle instruction. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). words: 1 cycles: 1(2) note: 3 cycles if skip and followed by a 2-word instruction. q cycle activity: q1 q2 q3 q4 decode read register ?f? process data no operation if skip: q1 q2 q3 q4 no operation no operation no operation no operation if skip and followed by 2-word instruction: q1 q2 q3 q4 no operation no operation no operation no operation no operation no operation no operation no operation example: here cpfslt reg, 1 nless : less : before instruction pc = address (here) w= ? after instruction if reg < w; pc = address (less) if reg w; pc = address (nless)
PIC18F6390/6490/8390/8490 ds39629b-page 314 preliminary ? 2004 microchip technology inc. daw decimal adjust w register syntax: daw operands: none operation: if [w<3:0> >9] or [dc = 1 ] then (w<3:0>) + 6 w<3:0>; else ( w<3:0>) w<3:0>; if [w<7:4> >9] or [c = 1 ] then ( w<7:4>) + 6 w<7:4>; c = 1 ; else (w<7:4>) w<7:4>; status affected: c encoding: 0000 0000 0000 0111 description: daw adjusts the eight-bit value in w, resulting from the earlier addition of two variables (each in packed bcd format) and produces a correct packed bcd result. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register w process data write w example 1: daw before instruction w=a5h c=0 dc = 0 after instruction w = 05h c=1 dc = 0 example 2 : before instruction w=ceh c=0 dc = 0 after instruction w = 34h c=1 dc = 0 decf decrement f syntax: decf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (f) ? 1 dest status affected: c, dc, n, ov, z encoding: 0000 01da ffff ffff description: decrement register ?f?. if ?d? is ? 0 ?, the result is stored in w. if ?d? is ? 1 ?, the result is stored back in register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: decf cnt, 1, 0 before instruction cnt = 01h z=0 after instruction cnt = 00h z=1
? 2004 microchip technology inc. preliminary ds39629b-page 315 PIC18F6390/6490/8390/8490 decfsz decrement f, skip if 0 syntax: decfsz f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (f) ? 1 dest, skip if result = 0 status affected: none encoding: 0010 11da ffff ffff description: the contents of register ?f? are decremented. if ?d? is ? 0 ?, the result is placed in w. if ?d? is ? 1 ?, the result is placed back in register ?f? (default). if the result is ? 0 ?, the next instruction which is already fetched is discarded and a nop is executed instead, making it a two-cycle instruction. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1(2) note: 3 cycles if skip and followed by a 2-word instruction. q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination if skip: q1 q2 q3 q4 no operation no operation no operation no operation if skip and followed by 2-word instruction: q1 q2 q3 q4 no operation no operation no operation no operation no operation no operation no operation no operation example: here decfsz cnt, 1, 1 goto loop continue before instruction pc = address (here) after instruction cnt = cnt ? 1 if cnt = 0; pc = address (continue) if cnt 0; pc = address (here + 2) dcfsnz decrement f, skip if not 0 syntax: dcfsnz f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (f) ? 1 dest, skip if result 0 status affected: none encoding: 0100 11da ffff ffff description: the contents of register ?f? are decremented. if ?d? is ? 0 ?, the result is placed in w. if ?d? is ? 1 ?, the result is placed back in register ?f? (default). if the result is not ? 0 ?, the next instruction which is already fetched is discarded and a nop is executed instead, making it a two-cycle instruction. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1(2) note: 3 cycles if skip and followed by a 2-word instruction. q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination if skip: q1 q2 q3 q4 no operation no operation no operation no operation if skip and followed by 2-word instruction: q1 q2 q3 q4 no operation no operation no operation no operation no operation no operation no operation no operation example: here dcfsnz temp, 1, 0 zero : nzero : before instruction temp = ? after instruction temp = temp ? 1, if temp = 0; pc = address (zero) if temp 0; pc = address (nzero)
PIC18F6390/6490/8390/8490 ds39629b-page 316 preliminary ? 2004 microchip technology inc. goto unconditional branch syntax: goto k operands: 0 k 1048575 operation: k pc<20:1> status affected: none encoding: 1st word (k<7:0>) 2nd word(k<19:8>) 1110 1111 1111 k 19 kkk k 7 kkk kkkk kkkk 0 kkkk 8 description: goto allows an unconditional branch anywhere within entire 2-mbyte memory range. the 20-bit value ?k? is loaded into pc<20:1>. goto is always a two-cycle instruction. words: 2 cycles: 2 q cycle activity: q1 q2 q3 q4 decode read literal ?k?<7:0>, no operation read literal ?k?<19:8>, write to pc no operation no operation no operation no operation example: goto there after instruction pc = address (there) incf increment f syntax: incf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (f) + 1 dest status affected: c, dc, n, ov, z encoding: 0010 10da ffff ffff description: the contents of register ?f? are incremented. if ?d? is ? 0 ?, the result is placed in w. if ?d? is ? 1 ?, the result is placed back in register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: incf cnt, 1, 0 before instruction cnt = ffh z=0 c=? dc = ? after instruction cnt = 00h z=1 c=1 dc = 1
? 2004 microchip technology inc. preliminary ds39629b-page 317 PIC18F6390/6490/8390/8490 incfsz increment f, skip if 0 syntax: incfsz f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (f) + 1 dest, skip if result = 0 status affected: none encoding: 0011 11da ffff ffff description: the contents of register ?f? are incremented. if ?d? is ? 0 ?, the result is placed in w. if ?d? is ? 1 ?, the result is placed back in register ?f? (default). if the result is ? 0 ?, the next instruction which is already fetched is discarded and a nop is executed instead, making it a two-cycle instruction. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1(2) note: 3 cycles if skip and followed by a 2-word instruction. q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination if skip: q1 q2 q3 q4 no operation no operation no operation no operation if skip and followed by 2-word instruction: q1 q2 q3 q4 no operation no operation no operation no operation no operation no operation no operation no operation example: here incfsz cnt, 1, 0 nzero : zero : before instruction pc = address (here) after instruction cnt = cnt + 1 if cnt = 0; pc = address (zero) if cnt 0; pc = address (nzero) infsnz increment f, skip if not 0 syntax: infsnz f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (f) + 1 dest, skip if result 0 status affected: none encoding: 0100 10da ffff ffff description: the contents of register ?f? are incremented. if ?d? is ? 0 ?, the result is placed in w. if ?d? is ? 1 ?, the result is placed back in register ?f? (default). if the result is not ? 0 ?, the next instruction which is already fetched is discarded and a nop is executed instead, making it a two-cycle instruction. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1(2) note: 3 cycles if skip and followed by a 2-word instruction. q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination if skip: q1 q2 q3 q4 no operation no operation no operation no operation if skip and followed by 2-word instruction: q1 q2 q3 q4 no operation no operation no operation no operation no operation no operation no operation no operation example: here infsnz reg, 1, 0 zero nzero before instruction pc = address (here) after instruction reg = reg + 1 if reg 0; pc = address (nzero) if reg = 0; pc = address (zero)
PIC18F6390/6490/8390/8490 ds39629b-page 318 preliminary ? 2004 microchip technology inc. iorlw inclusive or literal with w syntax: iorlw k operands: 0 k 255 operation: (w) .or. k w status affected: n, z encoding: 0000 1001 kkkk kkkk description: the contents of w are ored with the eight-bit literal ?k?. the result is placed in w. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read literal ?k? process data write to w example: iorlw 35h before instruction w=9ah after instruction w=bfh iorwf inclusive or w with f syntax: iorwf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (w) .or. (f) dest status affected: n, z encoding: 0001 00da ffff ffff description: inclusive or w with register ?f?. if ?d? is ? 0 ?, the result is placed in w. if ?d? is ? 1 ?, the result is placed back in register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: iorwf result, 0, 1 before instruction result = 13h w = 91h after instruction result = 13h w = 93h
? 2004 microchip technology inc. preliminary ds39629b-page 319 PIC18F6390/6490/8390/8490 lfsr load fsr syntax: lfsr f, k operands: 0 f 2 0 k 4095 operation: k fsrf status affected: none encoding: 1110 1111 1110 0000 00ff k 7 kkk k 11 kkk kkkk description: the 12-bit literal ?k? is loaded into the file select register pointed to by ?f?. words: 2 cycles: 2 q cycle activity: q1 q2 q3 q4 decode read literal ?k? msb process data write literal ?k? msb to fsrfh decode read literal ?k? lsb process data write literal ?k? to fsrfl example: lfsr 2, 3abh after instruction fsr2h = 03h fsr2l = abh movf move f syntax: movf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: f dest status affected: n, z encoding: 0101 00da ffff ffff description: the contents of register ?f? are moved to a destination dependent upon the status of ?d?. if ?d? is ? 0 ?, the result is placed in w. if ?d? is ? 1 ?, the result is placed back in register ?f? (default). location ?f? can be anywhere in the 256-byte bank. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write w example: movf reg, 0, 0 before instruction reg = 22h w=ffh after instruction reg = 22h w = 22h
PIC18F6390/6490/8390/8490 ds39629b-page 320 preliminary ? 2004 microchip technology inc. movff move f to f syntax: movff f s ,f d operands: 0 f s 4095 0 f d 4095 operation: (f s ) f d status affected: none encoding: 1st word (source) 2nd word (destin.) 1100 1111 ffff ffff ffff ffff fff f s fff f d description: the contents of source register ?f s ? are moved to destination register ?f d ?. location of source ?f s ? can be anywhere in the 4096-byte data space (000h to fffh) and location of destination ?f d ? can also be anywhere from 000h to fffh. either source or destination can be w (a useful special situation). movff is particularly useful for transferring a data memory location to a peripheral register (such as the transmit buffer or an i/o port). the movff instruction cannot use the pcl, tosu, tosh or tosl as the destination register words: 2 cycles: 2 (3) q cycle activity: q1 q2 q3 q4 decode read register ?f? (src) process data no operation decode no operation no dummy read no operation write register ?f? (dest) example: movff reg1, reg2 before instruction reg1 = 33h reg2 = 11h after instruction reg1 = 33h reg2 = 33h movlb move literal to low nibble in bsr syntax: movlw k operands: 0 k 255 operation: k bsr status affected: none encoding: 0000 0001 kkkk kkkk description: the eight-bit literal ?k? is loaded into the bank select register (bsr). the value of bsr<7:4> always remains ? 0 ?, regardless of the value of k 7 :k 4 . words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read literal ?k? process data write literal ?k? to bsr example: movlb 5 before instruction bsr register = 02h after instruction bsr register = 05h
? 2004 microchip technology inc. preliminary ds39629b-page 321 PIC18F6390/6490/8390/8490 movlw move literal to w syntax: movlw k operands: 0 k 255 operation: k w status affected: none encoding: 0000 1110 kkkk kkkk description: the eight-bit literal ?k? is loaded into w. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read literal ?k? process data write to w example: movlw 5ah after instruction w=5ah movwf move w to f syntax: movwf f {,a} operands: 0 f 255 a [0,1] operation: (w) f status affected: none encoding: 0110 111a ffff ffff description: move data from w to register ?f?. location ?f? can be anywhere in the 256-byte bank. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write register ?f? example: movwf reg, 0 before instruction w=4fh reg = ffh after instruction w=4fh reg = 4fh
PIC18F6390/6490/8390/8490 ds39629b-page 322 preliminary ? 2004 microchip technology inc. mullw multiply literal with w syntax: mullw k operands: 0 k 255 operation: (w) x k prodh:prodl status affected: none encoding: 0000 1101 kkkk kkkk description: an unsigned multiplication is carried out between the contents of w and the 8-bit literal ?k?. the 16-bit result is placed in the prodh:prodl register pair. prodh contains the high byte. w is unchanged. none of the status flags are affected. note that neither overflow nor carry is possible in this operation. a zero result is possible but not detected. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read literal ?k? process data write registers prodh: prodl example: mullw 0c4h before instruction w=e2h prodh = ? prodl = ? after instruction w=e2h prodh = adh prodl = 08h mulwf multiply w with f syntax: mulwf f {,a} operands: 0 f 255 a [0,1] operation: (w) x (f) prodh:prodl status affected: none encoding: 0000 001a ffff ffff description: an unsigned multiplication is carried out between the contents of w and the register file location ?f?. the 16-bit result is stored in the prodh:prodl register pair. prodh contains the high byte. both w and ?f? are unchanged. none of the status flags are affected. note that neither overflow nor carry is possible in this operation. a zero result is possible but not detected. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressi ng mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write registers prodh: prodl example: mulwf reg, 1 before instruction w=c4h reg = b5h prodh = ? prodl = ? after instruction w=c4h reg = b5h prodh = 8ah prodl = 94h
? 2004 microchip technology inc. preliminary ds39629b-page 323 PIC18F6390/6490/8390/8490 negf negate f syntax: negf f {,a} operands: 0 f 255 a [0,1] operation: ( f ) + 1 f status affected: n, ov, c, dc, z encoding: 0110 110a ffff ffff description: location ?f? is negated using two?s complement. the result is placed in the data memory location ?f?. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write register ?f? example: negf reg, 1 before instruction reg = 0011 1010 [3ah] after instruction reg = 1100 0110 [c6h] nop no operation syntax: nop operands: none operation: no operation status affected: none encoding: 0000 1111 0000 xxxx 0000 xxxx 0000 xxxx description: no operation. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode no operation no operation no operation example: none.
PIC18F6390/6490/8390/8490 ds39629b-page 324 preliminary ? 2004 microchip technology inc. pop pop top of return stack syntax: pop operands: none operation: (tos) bit bucket status affected: none encoding: 0000 0000 0000 0110 description: the tos value is pulled off the return stack and is discarded. the tos value then becomes the previous value that was pushed onto the return stack. this instruction is provided to enable the user to properly manage the return stack to incorporate a software stack. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode no operation pop tos value no operation example: pop goto new before instruction tos = 0031a2h stack (1 level down) = 014332h after instruction tos = 014332h pc = new push push top of return stack syntax: push operands: none operation: (pc + 2) tos status affected: none encoding: 0000 0000 0000 0101 description: the pc + 2 is pushed onto the top of the return stack. the previous tos value is pushed down on the stack. this instruction allows implementing a software stack by modifying tos and then pushing it onto the return stack. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode push pc + 2 onto return stack no operation no operation example: push before instruction tos = 345ah pc = 0124h after instruction pc = 0126h tos = 0126h stack (1 level down) = 345ah
? 2004 microchip technology inc. preliminary ds39629b-page 325 PIC18F6390/6490/8390/8490 rcall relative call syntax: rcall n operands: -1024 n 1023 operation: (pc) + 2 tos, (pc) + 2 + 2n pc status affected: none encoding: 1101 1nnn nnnn nnnn description: subroutine call with a jump up to 1k from the current location. first, return address (pc + 2) is pushed onto the stack. then, add the 2?s complement number ?2n? to the pc. since the pc will have incremented to fetch the next instruction, the new address will be pc + 2 + 2n. this instruction is a two-cycle instruction. words: 1 cycles: 2 q cycle activity: q1 q2 q3 q4 decode read literal ?n? push pc to stack process data write to pc no operation no operation no operation no operation example: here rcall jump before instruction pc = address (here) after instruction pc = address (jump) tos = address (here + 2) reset reset syntax: reset operands: none operation: reset all registers and flags that are affected by a mclr reset. status affected: all encoding: 0000 0000 1111 1111 description: this instruction provides a way to execute a mclr reset in software. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode start reset no operation no operation example: reset after instruction registers = reset value flags* = reset value
PIC18F6390/6490/8390/8490 ds39629b-page 326 preliminary ? 2004 microchip technology inc. retfie return from interrupt syntax: retfie {s} operands: s [0,1] operation: (tos) pc, 1 gie/gieh or peie/giel, if s = 1 (ws) w, (statuss) status, (bsrs) bsr, pclatu, pclath are unchanged. status affected: gie/gieh, peie/giel. encoding: 0000 0000 0001 000s description: return from interrupt. stack is popped and top-of-stack (tos) is loaded into the pc. interrupts are enabled by setting either the high or low priority global interrupt enable bit. if ?s? = 1 , the contents of the shadow registers, ws, statuss and bsrs, are loaded into their corresponding registers, w, status and bsr. if ?s? = 0 , no update of these registers occurs (default). words: 1 cycles: 2 q cycle activity: q1 q2 q3 q4 decode no operation no operation pop pc from stack set gieh or giel no operation no operation no operation no operation example: retfie 1 after interrupt pc = tos w=ws bsr = bsrs status = statuss gie/gieh, peie/giel = 1 retlw return literal to w syntax: retlw k operands: 0 k 255 operation: k w, (tos) pc, pclatu, pclath are unchanged status affected: none encoding: 0000 1100 kkkk kkkk description: w is loaded with the eight-bit literal ?k?. the program counter is loaded from the top of the stack (the return address). the high address latch (pclath) remains unchanged. words: 1 cycles: 2 q cycle activity: q1 q2 q3 q4 decode read literal ?k? process data pop pc from stack, write to w no operation no operation no operation no operation example: call table ; w contains table ; offset value ; w now has ; table value : table addwf pcl ; w = offset retlw k0 ; begin table retlw k1 ; : : retlw kn ; end of table before instruction w = 07h after instruction w = value of kn
? 2004 microchip technology inc. preliminary ds39629b-page 327 PIC18F6390/6490/8390/8490 return return from subroutine syntax: return {s} operands: s [0,1] operation: (tos) pc, if s = 1 (ws) w, (statuss) status, (bsrs) bsr, pclatu, pclath are unchanged status affected: none encoding: 0000 0000 0001 001s description: return from subroutine. the stack is popped and the top of the stack (tos) is loaded into the program counter. if ?s?= 1 , the contents of the shadow registers, ws, statuss and bsrs, are loaded into their corresponding registers, w, status and bsr. if ?s? = 0 , no update of these registers occurs (default). words: 1 cycles: 2 q cycle activity: q1 q2 q3 q4 decode no operation process data pop pc from stack no operation no operation no operation no operation example: return after interrupt pc = tos rlcf rotate left f through carry syntax: rlcf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (f) dest, (f<7>) c, (c) dest<0> status affected: c, n, z encoding: 0011 01da ffff ffff description: the contents of register ?f? are rotated one bit to the left through the carry flag. if ?d? is ? 0 ?, the result is placed in w. if ?d? is ? 1 ?, the result is stored back in register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: rlcf reg, 0, 0 before instruction reg = 1110 0110 c=0 after instruction reg = 1110 0110 w= 1100 1100 c=1 c register f
PIC18F6390/6490/8390/8490 ds39629b-page 328 preliminary ? 2004 microchip technology inc. rlncf rotate left f (no carry) syntax: rlncf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (f) dest, (f<7>) dest<0> status affected: n, z encoding: 0100 01da ffff ffff description: the contents of register ?f? are rotated one bit to the left. if ?d? is ? 0 ?, the result is placed in w. if ?d? is ? 1 ?, the result is stored back in register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: rlncf reg, 1, 0 before instruction reg = 1010 1011 after instruction reg = 0101 0111 register f rrcf rotate right f through carry syntax: rrcf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (f) dest, (f<0>) c, (c) dest<7> status affected: c, n, z encoding: 0011 00da ffff ffff description: the contents of register ?f? are rotated one bit to the right through the carry flag. if ?d? is ? 0 ?, the result is placed in w. if ?d? is ? 1 ?, the result is placed back in register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: rrcf reg, 0, 0 before instruction reg = 1110 0110 c=0 after instruction reg = 1110 0110 w= 0111 0011 c=0 c register f
? 2004 microchip technology inc. preliminary ds39629b-page 329 PIC18F6390/6490/8390/8490 rrncf rotate right f (no carry) syntax: rrncf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (f) dest, (f<0>) dest<7> status affected: n, z encoding: 0100 00da ffff ffff description: the contents of register ?f? are rotated one bit to the right. if ?d? is ? 0 ?, the result is placed in w. if ?d? is ? 1 ?, the result is placed back in register ?f? (default). if ?a? is ? 0 ?, the access bank will be selected, overriding the bsr value. if ?a? is ? 1 ?, then the bank will be selected as per the bsr value (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example 1: rrncf reg, 1, 0 before instruction reg = 1101 0111 after instruction reg = 1110 1011 example 2: rrncf reg, 0, 0 before instruction w=? reg = 1101 0111 after instruction w= 1110 1011 reg = 1101 0111 register f setf set f syntax: setf f {,a} operands: 0 f 255 a [0,1] operation: ffh f status affected: none encoding: 0110 100a ffff ffff description: the contents of the specified register are set to ffh. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write register ?f? example: setf reg,1 before instruction reg = 5ah after instruction reg = ffh
PIC18F6390/6490/8390/8490 ds39629b-page 330 preliminary ? 2004 microchip technology inc. sleep enter sleep mode syntax: sleep operands: none operation: 00h wdt, 0 wdt postscaler, 1 to , 0 pd status affected: to , pd encoding: 0000 0000 0000 0011 description: the power-down status bit (pd ) is cleared. the time-out status bit (to ) is set. watchdog timer and its postscaler are cleared. the processor is put into sleep mode with the oscillator stopped. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode no operation process data go to sleep example: sleep before instruction to =? pd =? after instruction to =1 ? pd =0 ? if wdt causes wake-up, this bit is cleared. subfwb subtract f from w with borrow syntax: subfwb f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (w) ? (f) ? (c ) dest status affected: n, ov, c, dc, z encoding: 0101 01da ffff ffff description: subtract register ?f? and carry flag (borrow) from w (2?s complement method). if ?d? is ? 0 ?, the result is stored in w. if ?d? is ? 1 ?, the result is stored in register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example 1: subfwb reg, 1, 0 before instruction reg = 3 w=2 c=1 after instruction reg = ff w=2 c=0 z=0 n = 1 ; result is negative example 2: subfwb reg, 0, 0 before instruction reg = 2 w=5 c=1 after instruction reg = 2 w=3 c=1 z=0 n = 0 ; result is positive example 3: subfwb reg, 1, 0 before instruction reg = 1 w=2 c=0 after instruction reg = 0 w=2 c=1 z = 1 ; result is zero n=0
? 2004 microchip technology inc. preliminary ds39629b-page 331 PIC18F6390/6490/8390/8490 sublw subtract w from literal syntax: sublw k operands: 0 k 255 operation: k ? (w) w status affected: n, ov, c, dc, z encoding: 0000 1000 kkkk kkkk description: w is subtracted from the eight-bit literal ?k?. the result is placed in w. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read literal ?k? process data write to w example 1: sublw 02h before instruction w = 01h c=? after instruction w = 01h c = 1 ; result is positive z=0 n=0 example 2: sublw 02h before instruction w = 02h c=? after instruction w = 00h c = 1 ; result is zero z=1 n=0 example 3: sublw 02h before instruction w = 03h c=? after instruction w = ffh; (2?s complement) c = 0 ; result is negative z=0 n=1 subwf subtract w from f syntax: subwf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (f) ? (w) dest status affected: n, ov, c, dc, z encoding: 0101 11da ffff ffff description: subtract w from register ?f? (2?s complement method). if ?d? is ? 0 ?, the result is stored in w. if ?d? is ? 1 ?, the result is stored back in register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example 1: subwf reg, 1, 0 before instruction reg = 3 w=2 c=? after instruction reg = 1 w=2 c = 1 ; result is positive z=0 n=0 example 2: subwf reg, 0, 0 before instruction reg = 2 w=2 c=? after instruction reg = 2 w=0 c = 1 ; result is zero z=1 n=0 example 3: subwf reg, 1, 0 before instruction reg = 1 w=2 c=? after instruction reg = ffh ;(2?s complement) w=2 c = 0 ; result is negative z=0 n=1
PIC18F6390/6490/8390/8490 ds39629b-page 332 preliminary ? 2004 microchip technology inc. subwfb subtract w from f with borrow syntax: subwfb f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (f) ? (w) ? (c ) dest status affected: n, ov, c, dc, z encoding: 0101 10da ffff ffff description: subtract w and the carry flag (borrow) from register ?f? (2?s complement method). if ?d? is ? 0 ?, the result is stored in w. if ?d? is ? 1 ?, the result is stored back in register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example 1: subwfb reg, 1, 0 before instruction reg = 19h (0001 1001) w=0dh (0000 1101) c=1 after instruction reg = 0ch (0000 1011) w=0dh (0000 1101) c=1 z=0 n = 0 ; result is positive example 2: subwfb reg, 0, 0 before instruction reg = 1bh (0001 1011) w=1ah (0001 1010) c=0 after instruction reg = 1bh (0001 1011) w = 00h c=1 z = 1 ; result is zero n=0 example 3: subwfb reg, 1, 0 before instruction reg = 03h (0000 0011) w=0eh (0000 1101) c=1 after instruction reg = f5h (1111 0100) ; [2?s comp] w=0eh (0000 1101) c=0 z=0 n = 1 ; result is negative swapf swap f syntax: swapf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (f<3:0>) dest<7:4>, (f<7:4>) dest<3:0> status affected: none encoding: 0011 10da ffff ffff description: the upper and lower nibbles of register ?f? are exchanged. if ?d? is ? 0 ?, the result is placed in w. if ?d? is ? 1 ?, the result is placed in register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset a ddressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: swapf reg, 1, 0 before instruction reg = 53h after instruction reg = 35h
? 2004 microchip technology inc. preliminary ds39629b-page 333 PIC18F6390/6490/8390/8490 tblrd table read syntax: tblrd ( *; *+; *-; +*) operands: none operation: if tblrd *, (prog mem (tblptr)) tablat; tblptr ? no change; if tblrd *+, (prog mem (tblptr)) tablat; (tblptr) + 1 tblptr; if tblrd *-, (prog mem (tblptr)) tablat; (tblptr) ? 1 tblptr; if tblrd +*, (tblptr) + 1 tblptr; (prog mem (tblptr)) tablat; status affected: none encoding: 0000 0000 0000 10nn nn=0 * =1 *+ =2 *- =3 +* description: this instruction is used to read the contents of program memory (p.m.). to address the program memory, a pointer, called table pointer (tblptr), is used. the tblptr (a 21-bit pointer) points to each byte in the program memory. tblptr has a 2-mbyte address range. tblptr[0] = 0 : least significant byte of program memory word tblptr[0] = 1 : most significant byte of program memory word the tblrd instruction can modify the value of tblptr as follows: no change post-increment post-decrement pre-increment words: 1 cycles: 2 q cycle activity: q1 q2 q3 q4 decode no operation no operation no operation no operation no operation (read program memory) no operation no operation (write tablat) tblrd table read (continued) example 1: tblrd *+ ; before instruction tablat = 55h tblptr = 00a356h memory(00a356h) = 34h after instruction tablat = 34h tblptr = 00a357h example 2: tblrd +* ; before instruction tablat = 0aah tblptr = 01a357h memory(01a357h) = 12h memory(01a358h) = 34h after instruction tablat = 34h tblptr = 01a358h
PIC18F6390/6490/8390/8490 ds39629b-page 334 preliminary ? 2004 microchip technology inc. tblwt table write syntax: tblwt ( *; *+; *-; +*) operands: none operation: if tblwt*, (tablat) holding register; tblptr ? no change; if tblwt*+, (tablat) holding register; (tblptr) + 1 tblptr; if tblwt*-, (tablat) holding register; (tblptr) ? 1 tblptr; if tblwt+*, (tblptr) + 1 tblptr; (tablat) holding register; status affected: none encoding: 0000 0000 0000 11nn nn=0 * =1 *+ =2 *- =3 +* description: this instruction uses the 3 lsbs of the tblptr to determine which of the 8 holding registers the tablat is written to. the holding registers are used to program the contents of program memory (p.m.). (refer to section 6.0 ?flash program memory? for additional details on programming flash memory.) the tblptr (a 21-bit pointer) points to each byte in the program memory. tblptr has a 2-mbtye address range. the lsb of the tblptr selects which byte of the program memory location to access. tblptr[0] = 0 : least significant byte of program memory word tblptr[0] = 1 : most significant byte of program memory word the tblwt instruction can modify the value of tblptr as follows: no change post-increment post-decrement pre-increment words: 1 cycles: 2 q cycle activity: q1 q2 q3 q4 decode no operation no operation no operation no operation no operation (read tablat) no operation no operation (write to holding register ) tblwt table write (continued) example 1: tblwt *+; before instruction tablat = 55h tblptr = 00a356h holding register (00a356h) = ffh after instructions (table write completion) tablat = 55h tblptr = 00a357h holding register (00a356h) = 55h example 2: tblwt +*; before instruction tablat = 34h tblptr = 01389ah holding register (01389ah) = ffh holding register (01389bh) = ffh after instruction (table write completion) tablat = 34h tblptr = 01389bh holding register (01389ah) = ffh holding register (01389bh) = 34h note: the table write ( tblwt ) instructions are not available in user mode in pic18f6x90/8x90 devices, as these devices are standard flash parts without an external bus interface.
? 2004 microchip technology inc. preliminary ds39629b-page 335 PIC18F6390/6490/8390/8490 tstfsz test f, skip if 0 syntax: tstfsz f {,a} operands: 0 f 255 a [0,1] operation: skip if f = 0 status affected: none encoding: 0110 011a ffff ffff description: if ?f? = 0 , the next instruction fetched during the current instruction execution is discarded and a nop is executed, making this a two-cycle instruction. if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1(2) note: 3 cycles if skip and followed by a 2-word instruction. q cycle activity: q1 q2 q3 q4 decode read register ?f? process data no operation if skip: q1 q2 q3 q4 no operation no operation no operation no operation if skip and followed by 2-word instruction: q1 q2 q3 q4 no operation no operation no operation no operation no operation no operation no operation no operation example: here tstfsz cnt, 1 nzero : zero : before instruction pc = address (here) after instruction if cnt = 00h, pc = address (zero) if cnt 00h, pc = address (nzero) xorlw exclusive or literal with w syntax: xorlw k operands: 0 k 255 operation: (w) .xor. k w status affected: n, z encoding: 0000 1010 kkkk kkkk description: the contents of w are xored with the 8-bit literal ?k?. the result is placed in w. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read literal ?k? process data write to w example: xorlw 0afh before instruction w=b5h after instruction w=1ah
PIC18F6390/6490/8390/8490 ds39629b-page 336 preliminary ? 2004 microchip technology inc. xorwf exclusive or w with f syntax: xorwf f {,d {,a}} operands: 0 f 255 d [0,1] a [0,1] operation: (w) .xor. (f) dest status affected: n, z encoding: 0001 10da ffff ffff description: exclusive or the contents of w with register ?f?. if ?d? is ? 0 ?, the result is stored in w. if ?d? is ? 1 ?, the result is stored back in the register ?f? (default). if ?a? is ? 0 ?, the access bank is selected. if ?a? is ? 1 ?, the bsr is used to select the gpr bank (default). if ?a? is ? 0 ? and the extended instruction set is enabled, this instruction operates in indexed literal offset addressing mode whenever f 95 (5fh). see section 24.2.3 ?byte-oriented and bit-oriented instructions in indexed literal offset mode? for details. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: xorwf reg, 1, 0 before instruction reg = afh w=b5h after instruction reg = 1ah w=b5h
? 2004 microchip technology inc. preliminary ds39629b-page 337 PIC18F6390/6490/8390/8490 24.2 extended instruction set in addition to the standard 75 instructions of the pic18 instruction set, pic18fxx90 devices also provide an optional extension to the core cpu functionality. the added features include eight additional instructions that augment indirect and indexed addressing operations and the implementation of indexed literal offset addressing mode for many of the standard pic18 instructions. the additional features are disabled by default. to enable them, users must set the xinst configuration bit. the instructions in the extended set can all be classified as literal operations, which either manipulate the file select registers or use them for indexed addressing. two of the instructions, addfsr and subfsr , each have an additional special instantiation for using fsr2. these versions ( addulnk and subulnk ) allow for automatic return after execution. the extended instructions are specifically implemented to optimize re-entrant program code (that is, code that is recursive or that uses a software stack) written in high-level languages, particularly c. among other things, they allow users working in high-level languages to perform certain operations on data structures more efficiently. these include: dynamic allocation and de-allocation of software stack space when entering and leaving subroutines function pointer invocation software stack pointer manipulation manipulation of variables located in a software stack a summary of the instructions in the extended instruc- tion set is provided in table 24-3. detailed descriptions are provided in section 24.2.2 ?extended instruction set? . the opcode field descriptions in table 24-1 apply to both the standard and extended pic18 instruction sets. 24.2.1 extended instruction syntax most of the extended instructions use indexed argu- ments, using one of the file select registers and some offset to specify a source or destination register. when an argument for an instruction serves as part of indexed addressing, it is enclosed in square brackets (?[ ]?). this is done to indicate that the argument is used as an index or offset. mpasm? assembler will flag an error if it determines that an index or offset value is not bracketed. when the extended instruction set is enabled, brackets are also used to indicate index arguments in byte- oriented and bit-oriented instructions. this is in addition to other changes in their syntax. for more details, see section 24.2.3.1 ?extended instruction syntax with standard pic18 commands? . table 24-3: extensions to the pic18 instruction set note: the instruction set extension and the indexed literal offset addressing mode were designed for optimizing applications written in c; the user may likely never use these instructions directly in assembler. the syntax for these commands is pro- vided as a reference for users who may be reviewing code that has been generated by a compiler. note: in the past, square brackets have been used to denote optional arguments in the pic18 and earlier instruction sets. in this text and going forward, optional arguments are denoted by braces (?{ }?). mnemonic, operands description cycles 16-bit instruction word status affected msb lsb addfsr addulnk callw movsf movss pushl subfsr subulnk f, k k z s , f d z s , z d k f, k k add literal to fsr add literal to fsr2 and return call subroutine using wreg move z s (source) to 1st word f d (destination) 2nd word move z s (source) to 1st word z d (destination) 2nd word store literal at fsr2, decrement fsr2 subtract literal from fsr subtract literal from fsr2 and return 1 2 2 2 2 1 1 2 1110 1110 0000 1110 1111 1110 1111 1110 1110 1110 1000 1000 0000 1011 ffff 1011 xxxx 1010 1001 1001 ffkk 11kk 0001 0zzz ffff 1zzz xzzz kkkk ffkk 11kk kkkk kkkk 0100 zzzz ffff zzzz zzzz kkkk kkkk kkkk none none none none none none none none
PIC18F6390/6490/8390/8490 ds39629b-page 338 preliminary ? 2004 microchip technology inc. 24.2.2 extended instruction set addfsr add literal to fsr syntax: addfsr f, k operands: 0 k 63 f [ 0, 1, 2 ] operation: fsr(f) + k fsr(f) status affected: none encoding: 1110 1000 ffkk kkkk description: the 6-bit literal ?k? is added to the contents of the fsr specified by ?f?. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read literal ?k? process data write to fsr example: addfsr 2, 23h before instruction fsr2 = 03ffh after instruction fsr2 = 0422h addulnk add literal to fsr2 and return syntax: addulnk k operands: 0 k 63 operation: fsr2 + k fsr2, pc = (tos) status affected: none encoding: 1110 1000 11kk kkkk description: the 6-bit literal ?k? is added to the contents of fsr2. a return is then executed by loading the pc with the tos. the instruction takes two cycles to execute; a nop is performed during the second cycle. this may be thought of as a special case of the addfsr instruction, where f = 3 (binary ? 11 ?); it operates only on fsr2. words: 1 cycles: 2 q cycle activity: q1 q2 q3 q4 decode read literal ?k? process data write to fsr no operation no operation no operation no operation example: addulnk 23h before instruction fsr2 = 03ffh pc = 0100h after instruction fsr2 = 0422h pc = (tos) note: all pic18 instructions may take an optional label argument preceding the instruction mnemonic for use in symbolic addressing. if a label is used, the instruction syntax then becomes: {label} instruction argument(s).
? 2004 microchip technology inc. preliminary ds39629b-page 339 PIC18F6390/6490/8390/8490 callw subroutine call using wreg syntax: callw operands: none operation: (pc + 2) tos, (w) pcl, (pclath) pch, (pclatu) pcu status affected: none encoding: 0000 0000 0001 0100 description first, the return address (pc + 2) is pushed onto the return stack. next, the contents of w are written to pcl; the existing value is discarded. then, the contents of pclath and pclatu are latched into pch and pcu, respectively. the second cycle is executed as a nop instruction while the new next instruction is fetched. unlike call , there is no option to update w, status or bsr. words: 1 cycles: 2 q cycle activity: q1 q2 q3 q4 decode read wreg push pc to stack no operation no operation no operation no operation no operation example: here callw before instruction pc = address (here) pclath = 10h pclatu = 00h w = 06h after instruction pc = 001006h tos = address (here + 2) pclath = 10h pclatu = 00h w = 06h movsf move indexed to f syntax: movsf [z s ], f d operands: 0 z s 127 0 f d 4095 operation: ((fsr2) + z s ) f d status affected: none encoding: 1st word (source) 2nd word (destin.) 1110 1111 1011 ffff 0zzz ffff zzzz s ffff d description: the contents of the source register are moved to destination register ?f d ?. the actual address of the source register is determined by adding the 7-bit literal offset ?z s ? in the first word to the value of fsr2. the address of the destination register is specified by the 12-bit literal ?f d ? in the second word. both addresses can be anywhere in the 4096-byte data space (000h to fffh). the movsf instruction cannot use the pcl, tosu, tosh or tosl as the destination register. if the resultant source address points to an indirect addressing register, the value returned will be 00h. words: 2 cycles: 2 q cycle activity: q1 q2 q3 q4 decode determine source addr determine source addr read source reg decode no operation no dummy read no operation write register ?f? (dest) example: movsf [05h], reg2 before instruction fsr2 = 80h contents of 85h = 33h reg2 = 11h after instruction fsr2 = 80h contents of 85h = 33h reg2 = 33h
PIC18F6390/6490/8390/8490 ds39629b-page 340 preliminary ? 2004 microchip technology inc. movss move indexed to indexed syntax: movss [z s ], [z d ] operands: 0 z s 127 0 z d 127 operation: ((fsr2) + z s ) ((fsr2) + z d ) status affected: none encoding: 1st word (source) 2nd word (dest.) 1110 1111 1011 xxxx 1zzz xzzz zzzz s zzzz d description the contents of the source register are moved to the destination register. the addresses of the source and destination registers are determined by adding the 7-bit literal offsets ?z s ? or ?z d ?, respectively, to the value of fsr2. both registers can be located anywhere in the 4096-byte data memory space (000h to fffh). the movss instruction cannot use the pcl, tosu, tosh or tosl as the destination register. if the resultant source address points to an indirect addressing register, the value returned will be 00h. if the resultant destination address points to an indirect addressing register, the instruction will execute as a nop . words: 2 cycles: 2 q cycle activity: q1 q2 q3 q4 decode determine source addr determine source addr read source reg decode determine dest addr determine dest addr write to dest reg example: movss [05h], [06h] before instruction fsr2 = 80h contents of 85h = 33h contents of 86h = 11h after instruction fsr2 = 80h contents of 85h = 33h contents of 86h = 33h pushl store literal at fsr2, decrement fsr2 syntax: pushl k operands: 0 k 255 operation: k (fsr2), fsr2 ? 1 fsr2 status affected: none encoding: 1111 1010 kkkk kkkk description: the 8-bit literal ?k? is written to the data memory address specified by fsr2. fsr2 is decremented by 1 after the operation. this instruction allows users to push values onto a software stack. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read ?k? process data write to destination example: pushl 08h before instruction fsr2h:fsr2l = 01ech memory (01ech) = 00h after instruction fsr2h:fsr2l = 01ebh memory (01ech) = 08h
? 2004 microchip technology inc. preliminary ds39629b-page 341 PIC18F6390/6490/8390/8490 subfsr subtract literal from fsr syntax: subfsr f, k operands: 0 k 63 f [ 0, 1, 2 ] operation: fsrf ? k fsrf status affected: none encoding: 1110 1001 ffkk kkkk description: the 6-bit literal ?k? is subtracted from the contents of the fsr specified by ?f?. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: subfsr 2, 23h before instruction fsr2 = 03ffh after instruction fsr2 = 03dch subulnk subtract literal from fsr2 and return syntax: subulnk k operands: 0 k 63 operation: fsr2 ? k fsr2 (tos) pc status affected: none encoding: 1110 1001 11kk kkkk description: the 6-bit literal ?k? is subtracted from the contents of the fsr2. a return is then executed by loading the pc with the tos. the instruction takes two cycles to execute; a nop is performed during the second cycle. this may be thought of as a special case of the subfsr instruction, where f = 3 (binary ? 11 ?); it operates only on fsr2. words: 1 cycles: 2 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination no operation no operation no operation no operation example: subulnk 23h before instruction fsr2 = 03ffh pc = 0100h after instruction fsr2 = 03dch pc = (tos)
PIC18F6390/6490/8390/8490 ds39629b-page 342 preliminary ? 2004 microchip technology inc. 24.2.3 byte-oriented and bit-oriented instructions in indexed literal offset mode in addition to eight new commands in the extended set, enabling the extended instruction set also enables indexed literal offset addressing mode ( section 5.6.1 ?indexed addressing with literal offset? ). this has a significant impact on the way that many commands of the standard pic18 instruction set are interpreted. when the extended set is disabled, addresses embed- ded in opcodes are treated as literal memory locations: either as a location in the access bank (a = 0 ), or in a gpr bank designated by the bsr (a = 1 ). when the extended instruction set is enabled and a = 0 , however, a file register argument of 5fh or less is interpreted as an offset from the pointer value in fsr2 and not as a literal address. for practical purposes, this means that all instructions that use the access ram bit as an argument ? that is, all byte-oriented and bit-oriented instructions, or almost half of the core pic18 instructions ? may behave differently when the extended instruction set is enabled. when the content of fsr2 is 00h, the boundaries of the access ram are essentially remapped to their original values. this may be useful in creating backward compatible code. if this technique is used, it may be necessary to save the value of fsr2 and restore it when moving back and forth between ?c? and assembly routines in order to preserve the stack pointer. users must also keep in mind the syntax requirements of the extended instruction set (see section 24.2.3.1 ?extended instruction syntax with standard pic18 commands? ). although the indexed literal offset addressing mode can be very useful for dynamic stack and pointer manipulation, it can also be very annoying if a simple arithmetic operation is carried out on the wrong register. users who are accustomed to the pic18 programming must keep in mind that, when the extended instruction set is enabled, register addresses of 5fh or less are used for indexed literal offset addressing. representative examples of typical byte-oriented and bit-oriented instructions in the indexed literal offset addressing mode are provided on the following page to show how execution is affected. the operand conditions shown in the examples are applicable to all instructions of these types. 24.2.3.1 extended instruction syntax with standard pic18 commands when the extended instruction set is enabled, the file register argument, ?f?, in the standard byte-oriented and bit-oriented commands is replaced with the literal offset value, ?k?. as already noted, this occurs only when ?f? is less than or equal to 5fh. when an offset value is used, it must be indicated by square brackets (?[ ]?). as with the extended instructions, the use of brackets indicates to the compiler that the value is to be interpreted as an index or an offset. omitting the brackets, or using a value greater than 5fh within brackets, will generate an error in the mpasm? assembler. if the index argument is properly bracketed for indexed literal offset addressing, the access ram argument is never specified; it will automatically be assumed to be ? 0 ?. this is in contrast to standard operation (extended instruction set disabled) when ?a? is set on the basis of the target address. declaring the access ram bit in this mode will also generate an error in the mpasm assembler. the destination argument, ?d?, functions as before. in the latest versions of the mpasm assembler, language support for the extended instruction set must be explicitly invoked. this is done with either the command line option, /y , or the pe directive in the source listing. 24.2.4 considerations when enabling the extended instruction set it is important to note that the extensions to the instruc- tion set may not be beneficial to all users. in particular, users who are not writing code that uses a software stack may not benefit from using the extensions to the instruction set. additionally, the indexed literal offset addressing mode may create issues with legacy applications written to the pic18 assembler. this is because instructions in the legacy code may attempt to address registers in the access bank below 5fh. since these addresses are interpreted as literal offsets to fsr2 when the instruction set extension is enabled, the application may read or write to the wrong data addresses. when porting an application to the pic18fxx90, it is very important to consider the type of code. a large, re- entrant application that is written in ?c? and would benefit from efficient compilation will do well when using the instruction set extensions. legacy applications that heavily use the access bank will most likely not benefit from using the extended instruction set. note: enabling the pic18 instruction set extension may cause legacy applications to behave erratically or fail entirely.
? 2004 microchip technology inc. preliminary ds39629b-page 343 PIC18F6390/6490/8390/8490 addwf add w to indexed (indexed literal offset mode) syntax: addwf [k] {,d} operands: 0 k 95 d [0,1] a = 0 operation: (w) + ((fsr2) + k) dest status affected: n, ov, c, dc, z encoding: 0010 01d0 kkkk kkkk description: the contents of w are added to the contents of the register indicated by fsr2, offset by the value ?k?. if ?d? is ? 0 ?, the result is stored in w. if ?d? is ? 1 ?, the result is stored back in register ?f? (default). words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read ?k? process data write to destination example: addwf [ofst] ,0 before instruction w = 17h ofst = 2ch fsr2 = 0a00h contents of 0a2ch = 20h after instruction w = 37h contents of 0a2ch = 20h bsf bit set indexed (indexed literal offset mode) syntax: bsf [k], b operands: 0 f 95 0 b 7 a = 0 operation: 1 ((fsr2 + k)) status affected: none encoding: 1000 bbb0 kkkk kkkk description: bit ?b? of the register indicated by fsr2, offset by the value ?k?, is set. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read register ?f? process data write to destination example: bsf [flag_ofst], 7 before instruction flag_ofst = 0ah fsr2 = 0a00h contents of 0a0ah = 55h after instruction contents of 0a0ah = d5h setf set indexed (indexed literal offset mode) syntax: setf [k] operands: 0 k 95 operation: ffh ((fsr2) + k) status affected: none encoding: 0110 1000 kkkk kkkk description: the contents of the register indicated by fsr2, offset by ?k?, are set to ffh. words: 1 cycles: 1 q cycle activity: q1 q2 q3 q4 decode read ?k? process data write register example: setf [ofst] before instruction ofst = 2ch fsr2 = 0a00h contents of 0a2ch = 00h after instruction contents of 0a2ch = ffh
PIC18F6390/6490/8390/8490 ds39629b-page 344 preliminary ? 2004 microchip technology inc. 24.2.5 special considerations with microchip mplab ? ide tools the latest versions of microchip?s software tools have been designed to fully support the extended instruction set of the pic18fxx90 family of devices. this includes the mplab c18 c compiler, mpasm assembly lan- guage and mplab integrated development environment (ide). when selecting a target device for software develop- ment, mplab ide will automatically set default config- uration bits for that device. the default setting for the xinst configuration bit is ? 0 ?, disabling the extended instruction set and indexed literal offset addressing mode. for proper execution of applications developed to take advantage of the extended instruction set, xinst must be set during programming. to develop software for the extended instruction set, the user must enable support for the instructions and the indexed addressing mode in their language tool(s). depending on the environment being used, this may be done in several ways: a menu option, or dialog box within the environment, that allows the user to configure the language tool and its settings for the project a command line option a directive in the source code these options vary between different compilers, assemblers and development environments. users are encouraged to review the documentation accompany- ing their development systems for the appropriate information.
? 2004 microchip technology inc. preliminary ds39629b-page 345 PIC18F6390/6490/8390/8490 25.0 development support the picmicro ? microcontrollers are supported with a full range of hardware and software development tools: integrated development environment - mplab ? ide software assemblers/compilers/linkers - mpasm tm assembler - mplab c17 and mplab c18 c compilers -mplink tm object linker/ mplib tm object librarian - mplab c30 c compiler - mplab asm30 assembler/linker/library simulators - mplab sim software simulator - mplab dspic30 software simulator emulators - mplab ice 2000 in-circuit emulator - mplab ice 4000 in-circuit emulator in-circuit debugger - mplab icd 2 device programmers -pro mate ? ii universal device programmer - picstart ? plus development programmer - mplab pm3 device programmer low-cost demonstration boards - picdem tm 1 demonstration board - picdem.net tm demonstration board - picdem 2 plus demonstration board - picdem 3 demonstration board - picdem 4 demonstration board - picdem 17 demonstration board - picdem 18r demonstration board - picdem lin demonstration board - picdem usb demonstration board evaluation kits -k ee l oq ? evaluation and programming tools - picdem msc -microid ? developer kits -can - powersmart ? developer kits -analog 25.1 mplab integrated development environment software the mplab ide software brings an ease of software development previously unseen in the 8/16-bit micro- controller market. the mplab ide is a windows ? based application that contains: an interface to debugging tools - simulator - programmer (sold separately) - emulator (sold separately) - in-circuit debugger (sold separately) a full-featured editor with color coded context a multiple project manager customizable data windows with direct edit of contents high-level source code debugging mouse over variable inspection extensive on-line help the mplab ide allows you to: edit your source files (either assembly or c) one touch assemble (or compile) and download to picmicro emulator and simulator tools (automatically updates all project information) debug using: - source files (assembly or c) - mixed assembly and c - machine code mplab ide supports multiple debugging tools in a single development paradigm, from the cost effective simulators, through low-cost in-circuit debuggers, to full-featured emulators. this eliminates the learning curve when upgrading to tools with increasing flexibility and power. 25.2 mpasm assembler the mpasm assembler is a full-featured, universal macro assembler for all picmicro mcus. the mpasm assembler generates relocatable object files for the mplink object linker, intel ? standard hex files, map files to detail memory usage and symbol ref- erence, absolute lst files that contain source lines and generated machine code and coff files for debugging. the mpasm assembler features include: integration into mplab ide projects user defined macros to streamline assembly code conditional assembly for multi-purpose source files directives that allow complete control over the assembly process
PIC18F6390/6490/8390/8490 ds39629b-page 346 preliminary ? 2004 microchip technology inc. 25.3 mplab c17 and mplab c18 c compilers the mplab c17 and mplab c18 code development systems are complete ansi c compilers for microchip?s pic17cxxx and pic18cxxx family of microcontrollers. these compilers provide powerful integration capabilities, superior code optimization and ease of use not found with other compilers. for easy source level debugging, the compilers provide symbol information that is optimized to the mplab ide debugger. 25.4 mplink object linker/ mplib object librarian the mplink object linker combines relocatable objects created by the mpasm assembler and the mplab c17 and mplab c18 c compilers. it can link relocatable objects from precompiled libraries, using directives from a linker script. the mplib object librarian manages the creation and modification of library files of precompiled code. when a routine from a library is called from a source file, only the modules that contain that routine will be linked in with the application. this allows large libraries to be used efficiently in many different applications. the object linker/library features include: efficient linking of single libraries instead of many smaller files enhanced code maintainability by grouping related modules together flexible creation of libraries with easy module listing, replacement, deletion and extraction 25.5 mplab c30 c compiler the mplab c30 c compiler is a full-featured, ansi compliant, optimizing compiler that translates standard ansi c programs into dspic30f assembly language source. the compiler also supports many command line options and language extensions to take full advantage of the dspic30f device hardware capabili- ties and afford fine control of the compiler code generator. mplab c30 is distributed with a complete ansi c standard library. all library functions have been vali- dated and conform to the ansi c library standard. the library includes functions for string manipulation, dynamic memory allocation, data conversion, time- keeping and math functions (trigonometric, exponential and hyperbolic). the compiler provides symbolic information for high-level source debugging with the mplab ide. 25.6 mplab asm30 assembler, linker and librarian mplab asm30 assembler produces relocatable machine code from symbolic assembly language for dspic30f devices. mplab c30 compiler uses the assembler to produce it?s object file. the assembler generates relocatable object files that can then be archived or linked with other relocatable object files and archives to create an executable file. notable features of the assembler include: support for the entire dspic30f instruction set support for fixed-point and floating-point data command line interface rich directive set flexible macro language mplab ide compatibility 25.7 mplab sim software simulator the mplab sim software simulator allows code devel- opment in a pc hosted environment by simulating the picmicro series microcontrollers on an instruction level. on any given instruction, the data areas can be examined or modified and stimuli can be applied from a file, or user defined key press, to any pin. the execu- tion can be performed in single-step, execute until break or trace mode. the mplab sim simulator fully supports symbolic debugging using the mplab c17 and mplab c18 c compilers, as well as the mpasm assembler. the software simulator offers the flexibility to develop and debug code outside of the laboratory environment, making it an excellent, economical software development tool. 25.8 mplab sim30 software simulator the mplab sim30 software simulator allows code development in a pc hosted environment by simulating the dspic30f series microcontrollers on an instruction level. on any given instruction, the data areas can be examined or modified and stimuli can be applied from a file, or user defined key press, to any of the pins. the mplab sim30 simulator fully supports symbolic debugging using the mplab c30 c compiler and mplab asm30 assembler. the simulator runs in either a command line mode for automated tasks, or from mplab ide. this high-speed simulator is designed to debug, analyze and optimize time intensive dsp routines.
? 2004 microchip technology inc. preliminary ds39629b-page 347 PIC18F6390/6490/8390/8490 25.9 mplab ice 2000 high-performance universal in-circuit emulator the mplab ice 2000 universal in-circuit emulator is intended to provide the product development engineer with a complete microcontroller design tool set for picmicro microcontrollers. software control of the mplab ice 2000 in-circuit emulator is advanced by the mplab integrated development environment, which allows editing, building, downloading and source debugging from a single environment. the mplab ice 2000 is a full-featured emulator sys- tem with enhanced trace, trigger and data monitoring features. interchangeable processor modules allow the system to be easily reconfigured for emulation of differ- ent processors. the universal architecture of the mplab ice in-circuit emulator allows expansion to support new picmicro microcontrollers. the mplab ice 2000 in-circuit emulator system has been designed as a real-time emulation system with advanced features that are typically found on more expensive development tools. the pc platform and microsoft ? windows 32-bit operating system were chosen to best make these features available in a simple, unified application. 25.10 mplab ice 4000 high-performance universal in-circuit emulator the mplab ice 4000 universal in-circuit emulator is intended to provide the product development engineer with a complete microcontroller design tool set for high- end picmicro microcontrollers. software control of the mplab ice in-circuit emulator is provided by the mplab integrated development environment, which allows editing, building, downloading and source debugging from a single environment. the mplab icd 4000 is a premium emulator system, providing the features of mplab ice 2000, but with increased emulation memory and high-speed perfor- mance for dspic30f and pic18xxxx devices. its advanced emulator features include complex triggering and timing, up to 2 mb of emulation memory and the ability to view variables in real-time. the mplab ice 4000 in-circuit emulator system has been designed as a real-time emulation system with advanced features that are typically found on more expensive development tools. the pc platform and microsoft windows 32-bit operating system were chosen to best make these features available in a simple, unified application. 25.11 mplab icd 2 in-circuit debugger microchip?s in-circuit debugger, mplab icd 2, is a powerful, low-cost, run-time development tool, connecting to the host pc via an rs-232 or high-speed usb interface. this tool is based on the flash picmicro mcus and can be used to develop for these and other picmicro microcontrollers. the mplab icd 2 utilizes the in-circuit debugging capability built into the flash devices. this feature, along with microchip?s in-circuit serial programming tm (icsp tm ) protocol, offers cost effective in-circuit flash debugging from the graphical user interface of the mplab integrated development environment. this enables a designer to develop and debug source code by setting breakpoints, single-stepping and watching variables, cpu status and peripheral registers. running at full speed enables testing hardware and applications in real-time. mplab icd 2 also serves as a development programmer for selected picmicro devices. 25.12 pro mate ii universal device programmer the pro mate ii is a universal, ce compliant device programmer with programmable voltage verification at v ddmin and v ddmax for maximum reliability. it features an lcd display for instructions and error messages and a modular detachable socket assembly to support various package types. in stand-alone mode, the pro mate ii device programmer can read, verify and program picmicro devices without a pc connection. it can also set code protection in this mode. 25.13 mplab pm3 device programmer the mplab pm3 is a universal, ce compliant device programmer with programmable voltage verification at v ddmin and v ddmax for maximum reliability. it features a large lcd display (128 x 64) for menus and error messages and a modular detachable socket assembly to support various package types. the icsp? cable assembly is included as a standard item. in stand- alone mode, the mplab pm3 device programmer can read, verify and program picmicro devices without a pc connection. it can also set code protection in this mode. mplab pm3 connects to the host pc via an rs- 232 or usb cable. mplab pm3 has high-speed com- munications and optimized algorithms for quick pro- gramming of large memory devices and incorporates an sd/mmc card for file storage and secure data appli- cations.
PIC18F6390/6490/8390/8490 ds39629b-page 348 preliminary ? 2004 microchip technology inc. 25.14 picstart plus development programmer the picstart plus development programmer is an easy-to-use, low-cost, prototype programmer. it con- nects to the pc via a com (rs-232) port. mplab integrated development environment software makes using the programmer simple and efficient. the picstart plus development programmer supports most picmicro devices up to 40 pins. larger pin count devices, such as the pic16c92x and pic17c76x, may be supported with an adapter socket. the picstart plus development programmer is ce compliant. 25.15 picdem 1 picmicro demonstration board the picdem 1 demonstration board demonstrates the capabilities of the pic16c5x (pic16c54 to pic16c58a), pic16c61, pic16c62x, pic16c71, pic16c8x, pic17c42, pic17c43 and pic17c44. all necessary hardware and software is included to run basic demo programs. the sample microcontrollers provided with the picdem 1 demonstration board can be programmed with a pro mate ii device program- mer or a picstart plus development programmer. the picdem 1 demonstration board can be connected to the mplab ice in-circuit emulator for testing. a prototype area extends the circuitry for additional appli- cation components. features include an rs-232 interface, a potentiometer for simulated analog input, push button switches and eight leds. 25.16 picdem.net internet/ethernet demonstration board the picdem.net demonstration board is an internet/ ethernet demonstration board using the pic18f452 microcontroller and tcp/ip firmware. the board supports any 40-pin dip device that conforms to the standard pinout used by the pic16f877 or pic18c452. this kit features a user friendly tcp/ip stack, web server with html, a 24l256 serial eeprom for xmodem download to web pages into serial eeprom, icsp/mplab icd 2 interface con- nector, an ethernet interface, rs-232 interface and a 16 x 2 lcd display. also included is the book and cd-rom ?tcp/ip lean, web servers for embedded systems,? by jeremy bentham 25.17 picdem 2 plus demonstration board the picdem 2 plus demonstration board supports many 18, 28 and 40-pin microcontrollers, including pic16f87x and pic18fxx2 devices. all the neces- sary hardware and software is included to run the dem- onstration programs. the sample microcontrollers provided with the picdem 2 demonstration board can be programmed with a pro mate ii device program- mer, picstart plus development programmer, or mplab icd 2 with a universal programmer adapter. the mplab icd 2 and mplab ice in-circuit emulators may also be used with the picdem 2 demonstration board to test firmware. a prototype area extends the circuitry for additional application components. some of the features include an rs-232 interface, a 2 x 16 lcd display, a piezo speaker, an on-board temperature sensor, four leds and sample pic18f452 and pic16f877 flash microcontrollers. 25.18 picdem 3 pic16c92x demonstration board the picdem 3 demonstration board supports the pic16c923 and pic16c924 in the plcc package. all the necessary hardware and software is included to run the demonstration programs. 25.19 picdem 4 8/14/18-pin demonstration board the picdem 4 can be used to demonstrate the capa- bilities of the 8, 14 and 18-pin pic16xxxx and pic18xxxx mcus, including the pic16f818/819, pic16f87/88, pic16f62xa and the pic18f1320 family of microcontrollers. picdem 4 is intended to showcase the many features of these low pin count parts, including lin and motor control using eccp. special provisions are made for low-power operation with the supercapacitor circuit and jumpers allow on- board hardware to be disabled to eliminate current draw in this mode. included on the demo board are pro- visions for crystal, rc or canned oscillator modes, a five volt regulator for use with a nine volt wall adapter or battery, db-9 rs-232 interface, icd connector for programming via icsp and development with mplab icd 2, 2 x 16 liquid crystal display, pcb footprints for h-bridge motor driver, lin transceiver and eeprom. also included are: header for expansion, eight leds, four potentiometers, three push buttons and a proto- typing area. included with the kit is a pic16f627a and a pic18f1320. tutorial firmware is included along with the user?s guide.
? 2004 microchip technology inc. preliminary ds39629b-page 349 PIC18F6390/6490/8390/8490 25.20 picdem 17 demonstration board the picdem 17 demonstration board is an evaluation board that demonstrates the capabilities of several microchip microcontrollers, including pic17c752, pic17c756a, pic17c762 and pic17c766. a pro- grammed sample is included. the pro mate ii device programmer, or the picstart plus development pro- grammer, can be used to reprogram the device for user tailored application development. the picdem 17 demonstration board supports program download and execution from external on-board flash memory. a generous prototype area is available for user hardware expansion. 25.21 picdem 18r pic18c601/801 demonstration board the picdem 18r demonstration board serves to assist development of the pic18c601/801 family of microchip microcontrollers. it provides hardware implementation of both 8-bit multiplexed/demultiplexed and 16-bit memory modes. the board includes 2 mb external flash memory and 128 kb sram memory, as well as serial eeprom, allowing access to the wide range of memory types supported by the pic18c601/801. 25.22 picdem lin pic16c43x demonstration board the powerful lin hardware and software kit includes a series of boards and three picmicro microcontrollers. the small footprint pic16c432 and pic16c433 are used as slaves in the lin communication and feature on-board lin transceivers. a pic16f874 flash microcontroller serves as the master. all three micro- controllers are programmed with firmware to provide lin bus communication. 25.23 pickit tm 1 flash starter kit a complete ?development system in a box?, the pickit? flash starter kit includes a convenient multi-section board for programming, evaluation and development of 8/14-pin flash pic ? microcontrollers. powered via usb, the board operates under a simple windows gui. the pickit 1 starter kit includes the user?s guide (on cd rom), pickit 1 tutorial software and code for various applications. also included are mplab ? ide (integrated development environment) software, software and hardware ?tips 'n tricks for 8-pin flash pic ? microcontrollers? handbook and a usb interface cable. supports all current 8/14-pin flash pic microcontrollers, as well as many future planned devices. 25.24 picdem usb pic16c7x5 demonstration board the picdem usb demonstration board shows off the capabilities of the pic16c745 and pic16c765 usb microcontrollers. this board provides the basis for future usb products. 25.25 evaluation and programming tools in addition to the picdem series of circuits, microchip has a line of evaluation kits and demonstration software for these products. k ee l oq evaluation and programming tools for microchip?s hcs secure data products can developers kit for automotive network applications analog design boards and filter design software powersmart battery charging evaluation/ calibration kits irda ? development kit microid development and rflab tm development software seeval ? designer kit for memory evaluation and endurance calculations picdem msc demo boards for switching mode power supply, high-power ir driver, delta sigma adc and flow rate sensor check the microchip web page and the latest product selector guide for the complete list of demonstration and evaluation kits.
PIC18F6390/6490/8390/8490 ds39629b-page 350 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 351 PIC18F6390/6490/8390/8490 26.0 electrical characteristics absolute maximum ratings (?) ambient temperature under bias................................................................................................. ............-40c to +125c storage temperature ............................................................................................................ .................. -65c to +150c voltage on any pin with respect to v ss (except v dd and mclr ) ................................................... -0.3v to (v dd + 0.3v) voltage on v dd with respect to v ss ......................................................................................................... -0.3v to +7.5v voltage on mclr with respect to v ss (note 2) ......................................................................................... 0v to +13.25v total power dissipation (note 1) ............................................................................................................................... 1.0w maximum current out of v ss pin ........................................................................................................................... 300 ma maximum current into v dd pin ........................................................................................................................... ...250 ma input clamp current, i ik (v i < 0 or v i > v dd ) ...................................................................................................................... 20 ma output clamp current, i ok (v o < 0 or v o > v dd ) .............................................................................................................. 20 ma maximum output current sunk by any i/o pin..................................................................................... .....................25 ma maximum output current sourced by any i/o pin .................................................................................. ..................25 ma maximum current sunk by all ports ...................................................................................................................... .200 ma maximum current sourced by all ports ........................................................................................... .......................200 ma note 1: power dissipation is calculated as follows: pdis = v dd x {i dd ? i oh } + {(v dd ? v oh ) x i oh } + (v ol x i ol ) 2: voltage spikes below v ss at the mclr /v pp /re3 pin, inducing currents greater than 80 ma, may cause latch-up. thus, a series resistor of 50-100 ? should be used when applying a ?low? level to the mclr /v pp / re3 pin, rather than pulling this pin directly to v ss . ? notice: stresses above those listed under ?absolute maximum ratings? may cause permanent damage to the device. this is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. exposure to maximum rating conditions for extended periods may affect device reliability.
PIC18F6390/6490/8390/8490 ds39629b-page 352 preliminary ? 2004 microchip technology inc. figure 26-1: PIC18F6390/6490/8390/8490 voltage-frequency graph (industrial) figure 26-2: pic18lf6390/6490/8390/8490 voltage-frequency graph (industrial) frequency voltage 6.0v 5.5v 4.5v 4.0v 2.0v 40 mhz 5.0v 3.5v 3.0v 2.5v pic18fx390/x490 4.2v frequency voltage 6.0v 5.5v 4.5v 4.0v 2.0v 40 mhz 5.0v 3.5v 3.0v 2.5v pic18lfx390/x490 f max = (16.36 mhz/v) (v ddappmin ? 2.0v) + 4 mhz note: v ddappmin is the minimum voltage of the picmicro ? device in the application. 4 mhz 4.2v
? 2004 microchip technology inc. preliminary ds39629b-page 353 PIC18F6390/6490/8390/8490 26.1 dc characteristics: supply voltage PIC18F6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial PIC18F6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. symbol characteristic min typ max units conditions d001 v dd supply voltage pic18lfx390/x490 2.0 ? 5.5 v hs, xt, rc and lp oscillator mode pic18fx390/x490 4.2 ? 5.5 v d002 v dr ram data retention voltage (1) 1.5 ? ? v d003 v por v dd start voltage to ensure internal power-on reset signal ? ? 0.7 v see section on power-on reset for details d004 s vdd v dd rise rate to ensure internal power-on reset signal 0.05 ? ? v/ms see section on power-on reset for details v bor brown-out reset voltage d005 pic18lfx390/x490 borv1:borv0 = 11 2.00 2.05 2.16 v borv1:borv0 = 10 2.65 2.79 2.93 v d005 all devices borv1:borv0 = 01 4.11 4.33 4.55 v borv1:borv0 = 00 4.36 4.59 4.82 v legend: shading of rows is to assist in readability of the table. note 1: this is the limit to which v dd can be lowered in sleep mode, or during a device reset, without losing ram data.
PIC18F6390/6490/8390/8490 ds39629b-page 354 preliminary ? 2004 microchip technology inc. 26.2 dc characteristics: power-down and supply current PIC18F6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial PIC18F6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. device typ max units conditions power-down current (i pd ) (1) pic18lfx390/x490 0.1 0.5 a -40c v dd = 2.0v, ( sleep mode) 0.1 0.5 a+25c 0.2 2.0 a+85c pic18lfx390/x490 0.1 0.5 a-40c v dd = 3.0v, ( sleep mode) 0.1 0.5 a+25c 0.3 5 a+85c all devices 0.1 2.0 a-40c v dd = 5.0v, ( sleep mode) 0.1 2.0 a+25c 0.4 10 a+85c legend: tbd = to be determined. shading of rows is to assist in readability of the table. note 1: the power-down current in sleep mode does not depend on the oscillator type. power-down current is measured with the part in sleep mode, with all i/o pins in high-impedance state and tied to v dd or v ss and all features that add delta current disabled (such as wdt, timer1 oscillator, bor, etc.). 2: the supply current is mainly a function of operating voltage, frequency and mode. other factors, such as i/o pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. the test conditions for all i dd measurements in active operation mode are: osc1 = external square wave, from rail-to-rail; all i/o pins tri-stated, pulled to v dd or v ss ; mclr = v dd ; wdt enabled/disabled as specified. 3: low-power timer1 oscillator selected. 4: bor and hlvd enable internal band gap reference. with both modules enabled, current consumption will be less than the sum of both specifications.
? 2004 microchip technology inc. preliminary ds39629b-page 355 PIC18F6390/6490/8390/8490 supply current (i dd ) (2) pic18lfx390/x490 12 26 a-40c v dd = 2.0v f osc = 31 khz ( rc_run mode, intrc source) 12 24 a +25c 12 23 a +85c pic18lfx390/x490 32 50 a-40c v dd = 3.0v 27 48 a +25c 22 46 a +85c all devices 84 134 a-40c v dd = 5.0v 82 128 a +25c 72 122 a +85c pic18lfx390/x490 .26 .8 ma -40c v dd = 2.0v f osc = 1 mhz ( rc_run mode, intosc source) .26 .8 ma +25c .26 .8 ma +85c pic18lfx390/x490 .48 1.04 ma -40c v dd = 3.0v .44 .96 ma +25c .48 .88 ma +85c all devices .88 1.84 ma -40c v dd = 5.0v .88 1.76 ma +25c .8 1.68 ma +85c 26.2 dc characteristics: power-down and supply current PIC18F6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) (continued) pic18lf6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial PIC18F6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. device typ max units conditions legend: tbd = to be determined. shading of rows is to assist in readability of the table. note 1: the power-down current in sleep mode does not depend on the oscillator type. power-down current is measured with the part in sleep mode, with all i/o pins in high-impedance state and tied to v dd or v ss and all features that add delta current disabled (such as wdt, timer1 oscillator, bor, etc.). 2: the supply current is mainly a function of operating voltage, frequency and mode. other factors, such as i/o pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. the test conditions for all i dd measurements in active operation mode are: osc1 = external square wave, from rail-to-rail; all i/o pins tri-stated, pulled to v dd or v ss ; mclr = v dd ; wdt enabled/disabled as specified. 3: low-power timer1 oscillator selected. 4: bor and hlvd enable internal band gap reference. with both modules enabled, current consumption will be less than the sum of both specifications.
PIC18F6390/6490/8390/8490 ds39629b-page 356 preliminary ? 2004 microchip technology inc. supply current (i dd ) (2) pic18lfx390/x490 0.6 1.7 a-40c v dd = 2.0v f osc = 4 mhz ( rc_run mode, intosc source) 0.6 1.6 a +25c 0.6 1.5 a +85c pic18lfx390/x490 1.0 2.4 ma -40c v dd = 3.0v 1.0 2.4 ma +25c 1.0 2.4 ma +85c all devices 2.0 4.2 ma -40c v dd = 5.0v 2.0 4 ma +25c 2.0 3.8 ma +85c pic18lfx390/x490 2.3 6.4 a-40c v dd = 2.0v f osc = 31 khz ( rc_idle mode, intrc source) 2.5 6.4 a +25c 2.9 8.8 a +85c pic18lfx390/x490 3.6 8.8 a-40c v dd = 3.0v 3.8 8.8 a +25c 4.6 12 a +85c all devices 7.4 13 a-40c v dd = 5.0v 7.8 13 a +25c 9.1 29 a +85c 26.2 dc characteristics: power-down and supply current PIC18F6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) (continued) pic18lf6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial PIC18F6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. device typ max units conditions legend: tbd = to be determined. shading of rows is to assist in readability of the table. note 1: the power-down current in sleep mode does not depend on the oscillator type. power-down current is measured with the part in sleep mode, with all i/o pins in high-impedance state and tied to v dd or v ss and all features that add delta current disabled (such as wdt, timer1 oscillator, bor, etc.). 2: the supply current is mainly a function of operating voltage, frequency and mode. other factors, such as i/o pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. the test conditions for all i dd measurements in active operation mode are: osc1 = external square wave, from rail-to-rail; all i/o pins tri-stated, pulled to v dd or v ss ; mclr = v dd ; wdt enabled/disabled as specified. 3: low-power timer1 oscillator selected. 4: bor and hlvd enable internal band gap reference. with both modules enabled, current consumption will be less than the sum of both specifications.
? 2004 microchip technology inc. preliminary ds39629b-page 357 PIC18F6390/6490/8390/8490 supply current (i dd ) (2) pic18lfx390/x490 132 280 a-40c v dd = 2.0v f osc = 1 mhz ( rc_idle mode, intosc source) 140 280 a +25c 152 280 a +85c pic18lfx390/x490 200 400 a-40c v dd = 3.0v 216 400 a +25c 252 400 a +85c all devices .40 .8 ma -40c v dd = 5.0v .42 .8 ma +25c .44 .8 ma +85c pic18lfx390/x490 272 400 a-40c v dd = 2.0v f osc = 4 mhz ( rc_idle mode, intosc source) 280 400 a +25c 288 400 a +85c pic18lfx390/x490 416 720 a-40c v dd = 3.0v 432 720 a +25c 464 720 a +85c all devices .8 1.3 ma -40c v dd = 5.0v .9 1.2 ma +25c .9 1.1 ma +85c 26.2 dc characteristics: power-down and supply current PIC18F6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) (continued) pic18lf6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial PIC18F6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. device typ max units conditions legend: tbd = to be determined. shading of rows is to assist in readability of the table. note 1: the power-down current in sleep mode does not depend on the oscillator type. power-down current is measured with the part in sleep mode, with all i/o pins in high-impedance state and tied to v dd or v ss and all features that add delta current disabled (such as wdt, timer1 oscillator, bor, etc.). 2: the supply current is mainly a function of operating voltage, frequency and mode. other factors, such as i/o pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. the test conditions for all i dd measurements in active operation mode are: osc1 = external square wave, from rail-to-rail; all i/o pins tri-stated, pulled to v dd or v ss ; mclr = v dd ; wdt enabled/disabled as specified. 3: low-power timer1 oscillator selected. 4: bor and hlvd enable internal band gap reference. with both modules enabled, current consumption will be less than the sum of both specifications.
PIC18F6390/6490/8390/8490 ds39629b-page 358 preliminary ? 2004 microchip technology inc. supply current (i dd ) (2) pic18lfx390/x490 250 500 a-40c v dd = 2.0v f osc = 1 mh z ( pri_run , ec oscillator) 260 500 a +25c 250 500 a +85c pic18lfx390/x490 550 650 a-40c v dd = 3.0v 480 650 a +25c 460 650 a +85c all devices 1.2 1.6 ma -40c v dd = 5.0v 1.1 1.5 ma +25c 1.0 1.4 ma +85c pic18lfx390/x490 0.72 2.0 ma -40c v dd = 2.0v f osc = 4 mhz ( pri_run , ec oscillator) 0.74 2.0 ma +25c 0.74 2.0 ma +85c pic18lfx390/x490 1.3 3.0 ma -40c v dd = 3.0v 1.3 3.0 ma +25c 1.3 3.0 ma +85c all devices 2.7 6.0 ma -40c v dd = 5.0v 2.6 6.0 ma +25c 2.5 6.0 ma +85c all devices 15 35 ma -40c v dd = 4.2v f osc = 40 mh z ( pri_run , ec oscillator) 16 35 ma +25c 16 35 ma +85c all devices 21 40 ma -40c v dd = 5.0v 21 40 ma +25c 21 40 ma +85c 26.2 dc characteristics: power-down and supply current PIC18F6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) (continued) pic18lf6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial PIC18F6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. device typ max units conditions legend: tbd = to be determined. shading of rows is to assist in readability of the table. note 1: the power-down current in sleep mode does not depend on the oscillator type. power-down current is measured with the part in sleep mode, with all i/o pins in high-impedance state and tied to v dd or v ss and all features that add delta current disabled (such as wdt, timer1 oscillator, bor, etc.). 2: the supply current is mainly a function of operating voltage, frequency and mode. other factors, such as i/o pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. the test conditions for all i dd measurements in active operation mode are: osc1 = external square wave, from rail-to-rail; all i/o pins tri-stated, pulled to v dd or v ss ; mclr = v dd ; wdt enabled/disabled as specified. 3: low-power timer1 oscillator selected. 4: bor and hlvd enable internal band gap reference. with both modules enabled, current consumption will be less than the sum of both specifications.
? 2004 microchip technology inc. preliminary ds39629b-page 359 PIC18F6390/6490/8390/8490 supply current (i dd ) (2) all devices 7.5 16 ma -40c v dd = 4.2v f osc = 4 mh z . 16 mhz internal ( pri_run hs+pll ) 7.4 15 ma +25c 7.3 14 ma +85c all devices 10 21 ma -40c v dd = 5.0v f osc = 4 mh z , 16 mhz internal ( pri_run hs+pll ) 10 20 ma +25c 9.7 19 ma +85c all devices 17 35 ma -40c v dd = 4.2v f osc = 10 mh z , 40 mhz internal ( pri_run hs+pll ) 17 35 ma +25c 17 35 ma +85c all devices 23 40 ma -40c v dd = 5.0v f osc = 10 mh z , 40 mhz internal ( pri_run hs+pll ) 23 40 ma +25c 23 40 ma +85c 26.2 dc characteristics: power-down and supply current PIC18F6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) (continued) pic18lf6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial PIC18F6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. device typ max units conditions legend: tbd = to be determined. shading of rows is to assist in readability of the table. note 1: the power-down current in sleep mode does not depend on the oscillator type. power-down current is measured with the part in sleep mode, with all i/o pins in high-impedance state and tied to v dd or v ss and all features that add delta current disabled (such as wdt, timer1 oscillator, bor, etc.). 2: the supply current is mainly a function of operating voltage, frequency and mode. other factors, such as i/o pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. the test conditions for all i dd measurements in active operation mode are: osc1 = external square wave, from rail-to-rail; all i/o pins tri-stated, pulled to v dd or v ss ; mclr = v dd ; wdt enabled/disabled as specified. 3: low-power timer1 oscillator selected. 4: bor and hlvd enable internal band gap reference. with both modules enabled, current consumption will be less than the sum of both specifications.
PIC18F6390/6490/8390/8490 ds39629b-page 360 preliminary ? 2004 microchip technology inc. supply current (i dd ) (2) pic18lfx390/x490 59 117 a-40c v dd = 2.0v f osc = 1 mhz ( pri_idle mode, ec oscillator) 59 108 a +25c 63 104 a +85c pic18lfx390/x490 108 243 a-40c v dd = 3.0v 108 225 a +25c 117 216 a +85c all devices 270 432 a-40c v dd = 5.0v 216 405 a +25c 270 387 a +85c pic18lfx390/x490 234 428 a-40c v dd = 2.0v f osc = 4 mhz ( pri_idle mode, ec oscillator) 230 405 a +25c 243 387 a +85c pic18lfx390/x490 378 810 a-40c v dd = 3.0v 387 765 a +25c 405 729 a +85c all devices .8 1.35 ma -40c v dd = 5.0v .8 1.26 ma +25c .8 1.17 ma +85c all devices 5.4 14.4 ma -40c v dd = 4.2v f osc = 40 mhz ( pri_idle mode, ec oscillator) 5.6 14.4 ma +25c 5.9 14.4 ma +85c all devices 7.3 16.2 ma -40c v dd = 5.0v 8.2 16.2 ma +25c 7.5 16.2 ma +85c 26.2 dc characteristics: power-down and supply current PIC18F6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) (continued) pic18lf6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial PIC18F6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. device typ max units conditions legend: tbd = to be determined. shading of rows is to assist in readability of the table. note 1: the power-down current in sleep mode does not depend on the oscillator type. power-down current is measured with the part in sleep mode, with all i/o pins in high-impedance state and tied to v dd or v ss and all features that add delta current disabled (such as wdt, timer1 oscillator, bor, etc.). 2: the supply current is mainly a function of operating voltage, frequency and mode. other factors, such as i/o pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. the test conditions for all i dd measurements in active operation mode are: osc1 = external square wave, from rail-to-rail; all i/o pins tri-stated, pulled to v dd or v ss ; mclr = v dd ; wdt enabled/disabled as specified. 3: low-power timer1 oscillator selected. 4: bor and hlvd enable internal band gap reference. with both modules enabled, current consumption will be less than the sum of both specifications.
? 2004 microchip technology inc. preliminary ds39629b-page 361 PIC18F6390/6490/8390/8490 supply current (i dd ) (2) pic18lfx390/x490 13 9 a-10c v dd = 2.0v f osc = 32 khz (4) ( sec_run mode, timer1 as clock) 14 9 a +25c 16 11 a +70c pic18lfx390/x490 34 12 a-10c v dd = 3.0v 31 12 a +25c 28 14 a +70c all devices 72 20 a-10c v dd = 5.0v 65 20 a +25c 59 25 a +70c pic18lfx390/x490 5.5 15 a-10c v dd = 2.0v f osc = 32 khz (4) ( sec_idle mode, timer1 as clock) 5.8 15 a +25c 6.1 18 a +70c pic18lfx390/x490 8.2 30 a-10c v dd = 3.0v 8.6 30 a +25c 8.8 35 a +70c all devices 13 80 a-10c v dd = 5.0v 13 80 a +25c 13 85 a +70c 26.2 dc characteristics: power-down and supply current PIC18F6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) (continued) pic18lf6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial PIC18F6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. device typ max units conditions legend: tbd = to be determined. shading of rows is to assist in readability of the table. note 1: the power-down current in sleep mode does not depend on the oscillator type. power-down current is measured with the part in sleep mode, with all i/o pins in high-impedance state and tied to v dd or v ss and all features that add delta current disabled (such as wdt, timer1 oscillator, bor, etc.). 2: the supply current is mainly a function of operating voltage, frequency and mode. other factors, such as i/o pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. the test conditions for all i dd measurements in active operation mode are: osc1 = external square wave, from rail-to-rail; all i/o pins tri-stated, pulled to v dd or v ss ; mclr = v dd ; wdt enabled/disabled as specified. 3: low-power timer1 oscillator selected. 4: bor and hlvd enable internal band gap reference. with both modules enabled, current consumption will be less than the sum of both specifications.
PIC18F6390/6490/8390/8490 ds39629b-page 362 preliminary ? 2004 microchip technology inc. module differential currents ( ? i wdt , ? i bor , ? i lvd , ? i lcd , ? i oscb , ? i ad ) d022 ( ? i wdt ) watchdog timer 1.7 4.0 a -40c 2.1 4.0 a +25c v dd = 2.0v 2.6 5.0 a +85c 2.2 6.0 a -40c 2.4 6.0 a +25c v dd = 3.0v 2.8 7.0 a +85c 2.9 10.0 a -40c 3.1 10.0 a +25c v dd = 5.0v 3.3 13.0 a +85c d022a ( ? i bor ) brown-out reset 17 35.0 a-40 c to +85 cv dd = 3.0v 47 45.0 a-40 c to +85 cv dd = 5.0v d022b ( ? i lvd ) high/low-voltage detect 14 25.0 a-40 c to +85 cv dd = 2.0v 18 35.0 a-40 c to +85 cv dd = 3.0v 21 45.0 a-40 c to +85 cv dd = 5.0v d024 ( ? i lcd ) lcd module 15 tbd a-40 c to +85 cv dd = 3.0v 20 tbd a-40 c to +85 cv dd = 5.0v d025 ( ? i oscb ) timer1 oscillator 1.0 3.5 a-10 c 1.1 3.5 a+25 cv dd = 2.0v 32 khz on timer1 (4) 1.1 4.5 a+70 c 1.2 4.5 a-10 c 1.3 4.5 a+25 cv dd = 3.0v 32 khz on timer1 (4) 1.2 5.5 a+70 c 1.8 6.0 a-10 c 1.9 6.0 a+25 cv dd = 5.0v 32 khz on timer1 (4) 1.9 7.0 a+70 c d026 ( ? i ad ) a/d converter 1.0 3.0 a? v dd = 2.0v a/d on, not converting 1.0 4.0 a? v dd = 3.0v 1.0 8.0 a? v dd = 5.0v 26.2 dc characteristics: power-down and supply current PIC18F6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) (continued) pic18lf6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial PIC18F6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. device typ max units conditions legend: tbd = to be determined. shading of rows is to assist in readability of the table. note 1: the power-down current in sleep mode does not depend on the oscillator type. power-down current is measured with the part in sleep mode, with all i/o pins in high-impedance state and tied to v dd or v ss and all features that add delta current disabled (such as wdt, timer1 oscillator, bor, etc.). 2: the supply current is mainly a function of operating voltage, frequency and mode. other factors, such as i/o pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. the test conditions for all i dd measurements in active operation mode are: osc1 = external square wave, from rail-to-rail; all i/o pins tri-stated, pulled to v dd or v ss ; mclr = v dd ; wdt enabled/disabled as specified. 3: low-power timer1 oscillator selected. 4: bor and hlvd enable internal band gap reference. with both modules enabled, current consumption will be less than the sum of both specifications.
? 2004 microchip technology inc. preliminary ds39629b-page 363 PIC18F6390/6490/8390/8490 26.3 dc characteristics: PIC18F6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) dc characteristics standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. symbol characteristic min max units conditions v il input low voltage i/o ports: d030 with ttl buffer v ss 0.15 v dd vv dd < 4.5v d030a ? 0.8 v 4.5v v dd 5.5v d031 with schmitt trigger buffer rc3 and rc4 v ss v ss 0.2 v dd 0.3 v dd v v d032 mclr v ss 0.2 v dd v d032a osc1 and t1osi v ss 0.3 v dd v lp, xt, hs, hspll modes (1) d033 osc1 v ss 0.2 v dd vec mode (1) v ih input high voltage i/o ports: d040 with ttl buffer 0.25 v dd + 0.8v v dd vv dd < 4.5v d040a 2.0 v dd v4.5v v dd 5.5v d041 with schmitt trigger buffer rc3 and rc4 0.8 v dd 0.7 v dd v dd v dd v v d042 mclr 0.8 v dd v dd v d042a osc1 and t1osi 0.7 v dd v dd v lp, xt, hs, hspll modes (1) d043 osc1 0.8 v dd v dd vec mode (1) i il input leakage current (2,3) d060 i/o ports ? 1 av ss v pin v dd , pin at hi-impedance d061 mclr ? 5 av ss v pin v dd d063 osc1 ? 5 av ss v pin v dd i pu weak pull-up current d070 i purb portb weak pull-up current 50 400 av dd = 5v, v pin = v ss note 1: in rc oscillator configuration, the osc1/clki pin is a schmitt trigger input. it is not recommended that the picmicro ? device be driven with an external clock while in rc mode. 2: the leakage current on the mclr pin is strongly dependent on the applied voltage level. the specified levels represent normal operating conditions. higher leakage current may be measured at different input voltages. 3: negative current is defined as current sourced by the pin. 4: parameter is characterized but not tested.
PIC18F6390/6490/8390/8490 ds39629b-page 364 preliminary ? 2004 microchip technology inc. v ol output low voltage d080 i/o ports ? 0.6 v i ol = 8.5 ma, v dd = 4.5v, -40 c to +85 c d083 osc2/clko (rc, rcio, ec, ecio modes) ?0.6vi ol = 1.6 ma, v dd = 4.5v, -40 c to +85 c v oh output high voltage (3) d090 i/o ports v dd ? 0.7 ? v i oh = -3.0 ma, v dd = 4.5v, -40 c to +85 c d092 osc2/clko (rc, rcio, ec, ecio modes) v dd ? 0.7 ? v i oh = -1.3 ma, v dd = 4.5v, -40 c to +85 c d150 v od open-drain high voltage ? 8.5 v ra4 pin capacitive loading specs on output pins d100 (4) c osc2 osc2 pin ? 15 pf in xt, hs and lp modes when external clock is used to drive osc1 d101 c io all i/o pins and osc2 (in rc mode) ? 50 pf to meet the ac timing specifications d102 c b scl, sda ? 400 pf i 2 c? specification 26.3 dc characteristics: PIC18F6390/6490/8390/8490 (industrial) pic18lf6390/6490/8390/8490 (industrial) (continued) dc characteristics standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. symbol characteristic min max units conditions note 1: in rc oscillator configuration, the osc1/clki pin is a schmitt trigger input. it is not recommended that the picmicro ? device be driven with an external clock while in rc mode. 2: the leakage current on the mclr pin is strongly dependent on the applied voltage level. the specified levels represent normal operating conditions. higher leakage current may be measured at different input voltages. 3: negative current is defined as current sourced by the pin. 4: parameter is characterized but not tested.
? 2004 microchip technology inc. preliminary ds39629b-page 365 PIC18F6390/6490/8390/8490 table 26-1: memory programming requirements dc characteristics standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. sym characteristic min typ? max units conditions program flash memory d110 v pp voltage on mclr /v pp pin 10.0 ? 12.0 v d113 i ddp supply current during programming ?? 1ma d130 e p cell endurance ? 1k ? e/w -40 c to +85 c d131 v pr v dd for read v min ?5.5vv min = minimum operating voltage d132 v ie v dd for block erase 4.5 ? 5.5 v using icsp? port d132a v iw v dd for externally timed erase or write 4.5 ? 5.5 v using icsp port d132b v pew v dd for self-timed write v min ?5.5vv min = minimum operating voltage d133 t ie icsp block erase cycle time ? 4 ? ms v dd > 4.5v d133a t iw icsp erase or write cycle time (externally timed) 2??msv dd > 4.5v d133a t iw self-timed write cycle time ? 2 ? ms d134 t retd characteristic retention 40 100 ? year provided no other specifications are violated ? data in ?typ? column is at 5.0v, 25c unless otherwise stated. these parameters are for design guidance only and are not tested.
PIC18F6390/6490/8390/8490 ds39629b-page 366 preliminary ? 2004 microchip technology inc. table 26-2: comparator specifications table 26-3: voltage reference specifications operating conditions: 3.0v < v dd < 5.5v, -40c < t a < +85c, unless otherwise stated. param no. sym characteristics min typ max units comments d300 v ioff input offset voltage ? 5.0 10 mv d301 v icm input common mode voltage* 0 ? v dd ? 1.5 v d302 cmrr common mode rejection ratio* 55 ? ? db 300 t resp response time (1)* ? 150 400 ns pic18 f xxxx 300a ? 150 600 ns pic18 lf xxxx, v dd = 2.0v 301 t mc 2 ov comparator mode change to output valid* ?? 10 s * these parameters are characterized but not tested. note 1: response time measured with one comparator input at (v dd ? 1.5)/2, while the other input transitions from v ss to v dd . operating conditions: 3.0v < v dd < 5.5v, -40c < t a < +85c, unless otherwise stated. param no. sym characteristics min typ max units comments d310 v res resolution v dd /24 ? v dd /32 lsb d311 vr aa absolute accuracy ? ? 1/2 lsb d312 vr ur unit resistor value (r) ? 2k ? ? 310 t set settling time (1) ? ? 10 s note 1: settling time measured while cvrr = 1 and cvr3:cvr0 transitions from ? 0000 ? to ? 1111 ?.
? 2004 microchip technology inc. preliminary ds39629b-page 367 PIC18F6390/6490/8390/8490 figure 26-3: high/low-voltage detect characteristics table 26-4: low-voltage detect characteristics v hlvd hlvdif v dd (hlvdif set by hardware) (hlvdif can be cleared in software) v hlvd for vdirmag = 1 : for vdirmag = 0 : v dd standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. symbol characteristic min typ? max units conditions d420 hlvd voltage on v dd transition high-to-low lvv = 0000 2.06 2.17 2.28 v lvv = 0001 2.12 2.23 2.34 v lvv = 0010 2.24 2.36 2.48 v lvv = 0011 2.32 2.44 2.56 v lvv = 0100 2.47 2.60 2.73 v lvv = 0101 2.65 2.79 2.93 v lvv = 0110 2.74 2.89 3.04 v lvv = 0111 2.96 3.12 3.28 v lvv = 1000 3.22 3.39 3.56 v lvv = 1001 3.37 3.55 3.73 v lvv = 1010 3.52 3.71 3.90 v lvv = 1011 3.70 3.90 4.10 v lvv = 1100 3.90 4.11 4.32 v lvv = 1101 4.11 4.33 4.55 v lvv = 1110 4.36 4.59 4.82 v ? production tested at t amb = 25c. specifications over temperature limits ensured by characterization.
PIC18F6390/6490/8390/8490 ds39629b-page 368 preliminary ? 2004 microchip technology inc. 26.4 ac (timing) characteristics 26.4.1 timing parameter symbology the timing parameter symbols have been created following one of the following formats: 1. tpps2pps 3. t cc : st (i 2 c specifications only) 2. tpps 4. ts (i 2 c specifications only) t f frequency t time lowercase letters (pp) and their meanings: pp cc ccp1 osc osc1 ck clko rd rd cs cs rw rd or wr di sdi sc sck do sdo ss ss dt data in t0 t0cki io i/o port t1 t13cki mc mclr wr wr uppercase letters and their meanings: s f fall p period hhigh rrise i invalid (high-impedance) v valid l low z high-impedance i 2 c only aa output access high high buf bus free low low t cc : st (i 2 c specifications only) cc hd hold su setup st dat data input hold sto stop condition sta start condition
? 2004 microchip technology inc. preliminary ds39629b-page 369 PIC18F6390/6490/8390/8490 26.4.2 timing conditions the temperature and voltages specified in table 26-5 apply to all timing specifications unless otherwise noted. figure 26-4 specifies the load conditions for the timing specifications. table 26-5: temperature and voltage specifications ? ac figure 26-4: load conditions for devi ce timing specifications note: because of space limitations, the generic terms ?pic18fxxxx? and ?pic18lfxxxx? are used throughout this section to refer to the PIC18F6390/6490/8390/8490 and pic18lf6390/6490/8390/8490 families of devices specifically and only those devices. ac characteristics standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial operating voltage v dd range as described in dc spec section 26.1 and section 26.3 . lf parts operate for industrial temperatures only. v dd /2 c l r l pin pin v ss v ss c l r l =464 ? c l = 50 pf for all pins except osc2/clko and including d and e outputs as ports load condition 1 load condition 2
PIC18F6390/6490/8390/8490 ds39629b-page 370 preliminary ? 2004 microchip technology inc. 26.4.3 timing diagrams and specifications figure 26-5: external clock timing (all modes except pll) table 26-6: external clock timing requirements osc1 clko q4 q1 q2 q3 q4 q1 1 2 3 3 4 4 param. no. symbol characteristic min max units conditions 1a f osc external clki frequency (1) dc 1 mhz xt, rc oscillator mode dc 20 mhz hs oscillator mode dc 31.25 khz lp oscillator mode oscillator frequency (1) dc 4 mhz rc oscillator mode 0.1 4 mhz xt oscillator mode 4 20 mhz hs oscillator mode 5 200 khz lp oscillator mode 1t osc external clki period (1) 1000 ? ns xt, rc oscillator mode 50 ? ns hs oscillator mode 32 ? s lp oscillator mode oscillator period (1) 250 ? ns rc oscillator mode 250 1 s xt oscillator mode 100 250 ns hs oscillator mode 50 250 ns hs oscillator mode 5? s lp oscillator mode 2t cy instruction cycle time (1) 100 ? ns t cy = 4/f osc 3t os l, t os h external clock in (osc1) high or low time 30 ? ns xt oscillator 2.5 ? s lp oscillator 10 ? ns hs oscillator 4t os r, t os f external clock in (osc1) rise or fall time ? 20 ns xt oscillator ? 50 ns lp oscillator ? 7.5 ns hs oscillator note 1: instruction cycle period (t cy ) equals four times the input oscillator time base period for all configurations except pll. all specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. all devices are tested to operate at ?min.? values with an external clock applied to the osc1/clki pin. when an external clock input is used, the ?max.? cycle time limit is ?dc? (no clock) for all devices.
? 2004 microchip technology inc. preliminary ds39629b-page 371 PIC18F6390/6490/8390/8490 table 26-7: pll clock timing specifications (v dd = 4.2v to 5.5v) table 26-8: ac characteristics:internal rc accuracy pic18lf6390/6490/8390/8490 (industrial) PIC18F6390/6490/8390/8490 (industrial) param no. sym characteristic min typ? max units conditions f10 f osc oscillator frequency range 4 ? 10 mhz hs mode only f11 f sys on-chip vco system frequency 16 ? 40 mhz hs mode only f12 t rc pll start-up time (lock time) ? ? 2 ms f13 ? clk clko stability (jitter) -2 ? +2 % ? data in ?typ? column is at 5v, 25 c, unless otherwise stated. these parameters are for design guidance only and are not tested. pic18lf6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial PIC18F6390/6490/8390/8490 (industrial) standard operating conditions (unless otherwise stated) operating temperature -40c t a +85c for industrial param no. device min typ max units conditions intosc accuracy @ freq = 8 mhz, 4 mhz, 2 mhz, 1 mhz, 500 khz, 250 khz, 125 khz (1) pic18lf6390/6490/8390/8490 -2 +/-1 2 % +25c v dd = 2.7-3.3 v -5 ? 5 % -10c to +85c v dd = 2.7-3.3 v -10 +/-1 10 % -40c to +85c v dd = 2.7-3.3 v PIC18F6390/6490/8390/8490 -2 +/-1 2 % +25c v dd = 4.5-5.5 v -5 ? 5 % -10c to +85c v dd = 4.5-5.5 v -10 +/-1 10 % -40c to +85c v dd = 4.5-5.5 v intrc accuracy @ freq = 31 khz (2) pic18lf6390/6490/8390/8490 26.562 ? 35.938 khz -40c to +85c v dd = 2.7-3.3 v PIC18F6390/6490/8390/8490 26.562 ? 35.938 khz -40c to +85c v dd = 4.5-5.5 v legend: shading of rows is to assist in readability of the table. note 1: frequency calibrated at 25c. osctune register can be used to compensate for temperature drift. 2: intrc frequency after calibration.
PIC18F6390/6490/8390/8490 ds39629b-page 372 preliminary ? 2004 microchip technology inc. figure 26-6: clko and i/o timing table 26-9: clko and i/o timing requirements note: refer to figure 26-4 for load conditions. osc1 clko i/o pin (input) i/o pin (output) q4 q1 q2 q3 10 13 14 17 20, 21 19 18 15 11 12 16 old value new value param no. symbol characteristic min typ max units conditions 10 t os h2 ck losc1 to clko ? 75 200 ns (note 1) 11 t os h2 ck hosc1 to clko ? 75 200 ns (note 1) 12 t ck r clko rise time ? 35 100 ns (note 1) 13 t ck f clko fall time ? 35 100 ns (note 1) 14 t ck l2 io vclko to port out valid ? ? 0.5 t cy + 20 ns (note 1) 15 t io v2 ck h port in valid before clko 0.25 t cy + 25 ? ? ns (note 1) 16 t ck h2 io i port in hold after clko 0??ns (note 1) 17 t os h2 io vosc1 (q1 cycle) to port out valid ? 50 150 ns 18 t os h2 io iosc1 (q2 cycle) to port input invalid (i/o in hold time) pic18 f xxxx 100 ? ? ns 18a pic18 lf xxxx 200 ? ? ns v dd = 2.0v 19 t io v2 os h port input valid to osc1 (i/o in setup time) 0 ? ? ns 20 t io r port output rise time pic18 f xxxx ? 10 25 ns 20a pic18 lf xxxx ? ? 60 ns v dd = 2.0v 21 t io f port output fall time pic18 f xxxx ? 10 25 ns 21a pic18 lf xxxx ? ? 60 ns v dd = 2.0v 22? t inp int pin high or low time t cy ??ns 23? t rbp rb7:rb4 change int high or low time t cy ??ns ? these parameters are asynchronous events not related to any internal clock edges. note 1: measurements are taken in rc mode, where clko output is 4 x t osc .
? 2004 microchip technology inc. preliminary ds39629b-page 373 PIC18F6390/6490/8390/8490 figure 26-7: reset, watchdog timer, oscillator start-up timer and power-up timer timing figure 26-8: brown-out reset timing table 26-10: reset, watchdog timer, oscillator start-up timer, power-up timer and brown-out reset requirements param. no. symbol characteristic min typ max units conditions 30 t mc lmclr pulse width (low) 2 ? ? s 31 t wdt watchdog timer time-out period (no postscaler) 3.4 4.0 4.6 ms 32 t ost oscillation start-up timer period 1024 t osc ? 1024 t osc ?t osc = osc1 period 33 t pwrt power-up timer period 55.5 65.5 tbd ms 34 t ioz i/o high-impedance from mclr low or watchdog timer reset ?2? s 35 t bor brown-out reset pulse width 200 ? ? sv dd b vdd (see d005) 36 t ivrst time for internal reference voltage to become stable ?2050 s 37 t lvd low-voltage detect pulse width 200 ? ? sv dd v lvd 38 t csd cpu start-up time ? 10 ? s 39 t iobst time for intrc block to stabilize ? 1 ? ms legend: tbd = to be determined v dd mclr internal por pwrt time-out osc time-out internal reset watchdog timer reset 33 32 30 31 34 i/o pins 34 note: refer to figure 26-4 for load conditions. v dd bv dd 35 v bgap = 1.2v v irvst enable internal internal reference 36 reference voltage voltage stable
PIC18F6390/6490/8390/8490 ds39629b-page 374 preliminary ? 2004 microchip technology inc. figure 26-9: timer0 and timer1 external clock timings table 26-11: timer0 and timer1 external clock requirements note: refer to figure 26-4 for load conditions. 46 47 45 48 41 42 40 t0cki t1oso/t13cki tmr0 or tmr1 param no. symbol characteristic min max units conditions 40 t t 0h t0cki high pulse width no prescaler 0.5 t cy + 20 ? ns with prescaler 10 ? ns 41 t t 0l t0cki low pulse width no prescaler 0.5 t cy + 20 ? ns with prescaler 10 ? ns 42 t t 0p t0cki period no prescaler t cy + 10 ? ns with prescaler greater of: 20 ns or (t cy + 40)/n ?nsn = prescale value (1, 2, 4,..., 256) 45 t t 1h t13cki high time synchronous, no prescaler 0.5 t cy + 20 ? ns synchronous, with prescaler pic18 f xxxx 10 ? ns pic18 lf xxxx 25 ? ns v dd = 2.0v asynchronous pic18 f xxxx 30 ? ns pic18 lf xxxx 50 ? ns v dd = 2.0v 46 t t 1l t13cki low time synchronous, no prescaler 0.5 t cy + 5 ? ns synchronous, with prescaler pic18 f xxxx 10 ? ns pic18 lf xxxx 25 ? ns v dd = 2.0v asynchronous pic18 f xxxx 30 ? ns pic18 lf xxxx 50 ? ns v dd = 2.0v 47 t t 1p t13cki input period synchronous greater of: 20 ns or (t cy + 40)/n ?nsn = prescale value (1, 2, 4, 8) asynchronous 60 ? ns f t 1 t13cki oscillator input frequency range dc 50 khz 48 t cke 2 tmr i delay from external t13cki clock edge to timer increment 2 t osc 7 t osc ?
? 2004 microchip technology inc. preliminary ds39629b-page 375 PIC18F6390/6490/8390/8490 figure 26-10: capture/compare/pwm timings (all ccp modules) table 26-12: capture/compare/pwm requirements (all ccp modules) note: refer to figure 26-4 for load conditions. ccpx (capture mode) 50 51 52 ccpx 53 54 (compare or pwm mode) param no. symbol characteristic min max units conditions 50 t cc l ccpx input low time no prescaler 0.5 t cy + 20 ? ns with prescaler pic18 f xxxx 10 ? ns pic18 lf xxxx 20 ? ns v dd = 2.0v 51 t cc h ccpx input high time no prescaler 0.5 t cy + 20 ? ns with prescaler pic18 f xxxx 10 ? ns pic18 lf xxxx 20 ? ns v dd = 2.0v 52 t cc p ccpx input period 3 t cy + 40 n ? ns n = prescale value (1, 4 or 16) 53 t cc r ccpx output fall time pic18 f xxxx ? 25 ns pic18 lf xxxx ? 45 ns v dd = 2.0v 54 t cc f ccpx output fall time pic18 f xxxx ? 25 ns pic18 lf xxxx ? 45 ns v dd = 2.0v
PIC18F6390/6490/8390/8490 ds39629b-page 376 preliminary ? 2004 microchip technology inc. figure 26-11: example spi? master mode timing (cke = 0 ) table 26-13: example spi? mode requirements (master mode, cke = 0 ) ss sck (ckp = 0 ) sck (ckp = 1 ) sdo sdi 70 71 72 73 74 75, 76 78 79 80 79 78 msb lsb bit 6 - - - - - - 1 msb in lsb in bit 6 - - - - 1 note: refer to figure 26-4 for load conditions. param no. symbol characteristic min max units conditions 70 t ss l2 sc h, t ss l2 sc l ss to sck or sck input t cy ?ns 71 t sc h sck input high time (slave mode) continuous 1.25 t cy + 30 ? ns 71a single byte 40 ? ns (note 1) 72 t sc l sck input low time (slave mode) continuous 1.25 t cy + 30 ? ns 72a single byte 40 ? ns (note 1) 73 t di v2 sc h, t di v2 sc l setup time of sdi data input to sck edge 100 ? ns 73a t b 2 b last clock edge of byte 1 to the 1st clock edge of byte 2 1.5 t cy + 40 ? ns (note 2) 74 t sc h2 di l, t sc l2 di l hold time of sdi data input to sck edge 100 ? ns 75 t do r sdo data output rise time pic18 f xxxx ? 25 ns pic18 lf xxxx ? 45 ns v dd = 2.0v 76 t do f sdo data output fall time ? 25 ns 78 t sc r sck output rise time (master mode) pic18 f xxxx ? 25 ns pic18 lf xxxx ? 45 ns v dd = 2.0v 79 t sc f sck output fall time (master mode) ? 25 ns 80 t sc h2 do v, t sc l2 do v sdo data output valid after sck edge pic18 f xxxx ? 50 ns pic18 lf xxxx ? 100 ns v dd = 2.0v note 1: requires the use of parameter #73a. 2: only if parameter #71a and #72a are used.
? 2004 microchip technology inc. preliminary ds39629b-page 377 PIC18F6390/6490/8390/8490 figure 26-12: example spi? master mode timing (cke = 1 ) table 26-14: example spi? mode requirements (master mode, cke = 1 ) ss sck (ckp = 0 ) sck (ckp = 1 ) sdo sdi 81 71 72 74 75, 76 78 80 msb 79 73 msb in bit 6 - - - - - - 1 lsb in bit 6 - - - - 1 lsb note: refer to figure 26-4 for load conditions. param. no. symbol characteristic min max units conditions 71 t sc h sck input high time (slave mode) continuous 1.25 t cy + 30 ? ns 71a single byte 40 ? ns (note 1) 72 t sc l sck input low time (slave mode) continuous 1.25 t cy + 30 ? ns 72a single byte 40 ? ns (note 1) 73 t di v2 sc h, t di v2 sc l setup time of sdi data input to sck edge 100 ? ns 73a t b 2 b last clock edge of byte 1 to the 1st clock edge of byte 2 1.5 t cy + 40 ? ns (note 2) 74 t sc h2 di l, t sc l2 di l hold time of sdi data input to sck edge 100 ? ns 75 t do r sdo data output rise time pic18 f xxxx ? 25 ns pic18 lf xxxx ? 45 ns v dd = 2.0v 76 t do f sdo data output fall time ? 25 ns 78 t sc r sck output rise time (master mode) pic18 f xxxx ? 25 ns pic18 lf xxxx ? 45 ns v dd = 2.0v 79 t sc f sck output fall time (master mode) ? 25 ns 80 t sc h2 do v, t sc l2 do v sdo data output valid after sck edge pic18 f xxxx ? 50 ns pic18 lf xxxx ? 100 ns v dd = 2.0v 81 t do v2 sc h, t do v2 sc l sdo data output setup to sck edge t cy ?ns note 1: requires the use of parameter #73a. 2: only if parameter #71a and #72a are used.
PIC18F6390/6490/8390/8490 ds39629b-page 378 preliminary ? 2004 microchip technology inc. figure 26-13: example spi? slave mode timing (cke = 0 ) table 26-15: example spi? mode requirements (slave mode timing, cke = 0 ) param no. symbol characteristic min max units conditions 70 t ss l2 sc h, t ss l2 sc l ss to sck or sck input t cy ?ns 71 t sc h sck input high time (slave mode) continuous 1.25 t cy + 30 ? ns 71a single byte 40 ? ns (note 1) 72 t sc l sck input low time (slave mode) continuous 1.25 t cy + 30 ? ns 72a single byte 40 ? ns (note 1) 73 t di v2 sc h, t di v2 sc l setup time of sdi data input to sck edge 100 ? ns 73a t b 2 b last clock edge of byte 1 to the first clock edge of byte 2 1.5 t cy + 40 ? ns (note 2) 74 t sc h2 di l, t sc l2 di l hold time of sdi data input to sck edge 100 ? ns 75 t do r sdo data output rise time pic18 f xxxx ? 25 ns pic18 lf xxxx ? 45 ns v dd = 2.0v 76 t do f sdo data output fall time ? 25 ns 77 t ss h2 do zss to sdo output hi-impedance 10 50 ns 78 t sc r sck output rise time (master mode) pic18 f xxxx ? 25 ns pic18 lf xxxx ? 45 ns v dd = 2.0v 79 t sc f sck output fall time (master mode) ? 25 ns 80 t sc h2 do v, t sc l2 do v sdo data output valid after sck edge pic18 f xxxx ? 50 ns pic18 lf xxxx ? 100 ns v dd = 2.0v 83 t sc h2 ss h, t sc l2 ss h ss after sck edge 1.5 t cy + 40 ? ns note 1: requires the use of parameter #73a. 2: only if parameter #71a and #72a are used. ss sck (ckp = 0 ) sck (ckp = 1 ) sdo sdi 70 71 72 73 74 75, 76 77 78 79 80 79 78 sdi msb lsb bit 6 - - - - - - 1 msb in bit 6 - - - - 1 lsb in 83 note: refer to figure 26-4 for load conditions.
? 2004 microchip technology inc. preliminary ds39629b-page 379 PIC18F6390/6490/8390/8490 figure 26-14: example spi? slave mode timing (cke = 1 ) table 26-16: example spi? slave mode requirements (cke = 1 ) param no. symbol characteristic min max units conditions 70 t ss l2 sc h, t ss l2 sc l ss to sck or sck input t cy ?ns 71 t sc h sck input high time (slave mode) continuous 1.25 t cy + 30 ? ns 71a single byte 40 ? ns (note 1) 72 t sc l sck input low time (slave mode) continuous 1.25 t cy + 30 ? ns 72a single byte 40 ? ns (note 1) 73a t b 2 b last clock edge of byte 1 to the first clock edge of byte 2 1.5 t cy + 40 ? ns (note 2) 74 t sc h2 di l, t sc l2 di l hold time of sdi data input to sck edge 100 ? ns 75 t do r sdo data output rise time pic18 f xxxx ? 25 ns pic18 lf xxxx ? 45 ns v dd = 2.0v 76 t do f sdo data output fall time ? 25 ns 77 t ss h2 do zss to sdo output high-impedance 10 50 ns 78 t sc r sck output rise time (master mode) pic18 f xxxx ? 25 ns pic18 lf xxxx ? 45 ns v dd = 2.0v 79 t sc f sck output fall time (master mode) ? 25 ns 80 t sc h2 do v, t sc l2 do v sdo data output valid after sck edge pic18 f xxxx ? 50 ns pic18 lf xxxx ? 100 ns v dd = 2.0v 82 t ss l2 do v sdo data output valid after ss edge pic18 f xxxx ? 50 ns pic18 lf xxxx ? 100 ns v dd = 2.0v 83 t sc h2 ss h, t sc l2 ss h ss after sck edge 1.5 t cy + 40 ? ns note 1: requires the use of parameter #73a. 2: only if parameter #71a and #72a are used. ss sck (ckp = 0 ) sck (ckp = 1 ) sdo sdi 70 71 72 82 sdi 74 75, 76 msb bit 6 - - - - - - 1 lsb 77 msb in bit 6 - - - - 1 lsb in 80 83 note: refer to figure 26-4 for load conditions.
PIC18F6390/6490/8390/8490 ds39629b-page 380 preliminary ? 2004 microchip technology inc. figure 26-15: i 2 c? bus start/stop bits timing table 26-17: i 2 c? bus start/stop bits requirements (slave mode) figure 26-16: i 2 c? bus data timing note: refer to figure 26-4 for load conditions. 91 92 93 scl sda start condition stop condition 90 param. no. symbol characteristic min max units conditions 90 t su : sta start condition 100 khz mode 4700 ? ns only relevant for repeated start condition setup time 400 khz mode 600 ? 91 t hd : sta start condition 100 khz mode 4000 ? ns after this period, the first clock pulse is generated hold time 400 khz mode 600 ? 92 t su : sto stop condition 100 khz mode 4700 ? ns setup time 400 khz mode 600 ? 93 t hd : sto stop condition 100 khz mode 4000 ? ns hold time 400 khz mode 600 ? note: refer to figure 26-4 for load conditions. 90 91 92 100 101 103 106 107 109 109 110 102 scl sda in sda out
? 2004 microchip technology inc. preliminary ds39629b-page 381 PIC18F6390/6490/8390/8490 table 26-18: i 2 c? bus data requirements (slave mode) param. no. symbol characteristic min max units conditions 100 t high clock high time 100 khz mode 4.0 ? s pic18fxxxx must operate at a minimum of 1.5 mhz 400 khz mode 0.6 ? s pic18fxxxx must operate at a minimum of 10 mhz ssp module 1.5 t cy ? 101 t low clock low time 100 khz mode 4.7 ? s pic18fxxxx must operate at a minimum of 1.5 mhz 400 khz mode 1.3 ? s pic18fxxxx must operate at a minimum of 10 mhz ssp module 1.5 t cy ? 102 t r sda and scl rise time 100 khz mode ? 1000 ns 400 khz mode 20 + 0.1 c b 300 ns c b is specified to be from 10 to 400 pf 103 t f sda and scl fall time 100 khz mode ? 300 ns 400 khz mode 20 + 0.1 c b 300 ns c b is specified to be from 10 to 400 pf 90 t su : sta start condition setup time 100 khz mode 4.7 ? s only relevant for repeated start condition 400 khz mode 0.6 ? s 91 t hd : sta start condition hold time 100 khz mode 4.0 ? s after this period, the first clock pulse is generated 400 khz mode 0.6 ? s 106 t hd : dat data input hold time 100 khz mode 0 ? ns 400 khz mode 0 0.9 s 107 t su : dat data input setup time 100 khz mode 250 ? ns (note 2) 400 khz mode 100 ? ns 92 t su : sto stop condition setup time 100 khz mode 4.7 ? s 400 khz mode 0.6 ? s 109 t aa output valid from clock 100 khz mode ? 3500 ns (note 1) 400 khz mode ? ? ns 110 t buf bus free time 100 khz mode 4.7 ? s time the bus must be free before a new transmission can start 400 khz mode 1.3 ? s d102 c b bus capacitive loading ? 400 pf note 1: as a transmitter, the device must provi de this internal minimum delay time to bridge the undefined region (min. 300 ns) of the falling edge of scl to avoid unintended generation of start or stop conditions. 2: a fast mode i 2 c bus device can be used in a standard mode i 2 c? bus system, but the requirement, t su : dat 250 ns, must then be met. this will automatically be the case if the device does not stretch the low period of the scl signal. if such a device does stretch the low period of the scl signal, it must output the next data bit to the sda line, t r max. + t su : dat = 1000 + 250 = 1250 ns (according to the standard mode i 2 c bus specification), before the scl line is released.
PIC18F6390/6490/8390/8490 ds39629b-page 382 preliminary ? 2004 microchip technology inc. figure 26-17: master ssp i 2 c? bus start/stop bits timing waveforms table 26-19: master ssp i 2 c? bus start/stop bits requirements figure 26-18: master ssp i 2 c? bus data timing note: refer to figure 26-4 for load conditions. 91 93 scl sda start condition stop condition 90 92 param. no. symbol characteristic min max units conditions 90 t su : sta start condition 100 khz mode 2(t osc )(brg + 1) ? ns only relevant for repeated start condition setup time 400 khz mode 2(t osc )(brg + 1) ? 1 mhz mode (1) 2(t osc )(brg + 1) ? 91 t hd : sta start condition 100 khz mode 2(t osc )(brg + 1) ? ns after this period, the first clock pulse is generated hold time 400 khz mode 2(t osc )(brg + 1) ? 1 mhz mode (1) 2(t osc )(brg + 1) ? 92 t su : sto stop condition 100 khz mode 2(t osc )(brg + 1) ? ns setup time 400 khz mode 2(t osc )(brg + 1) ? 1 mhz mode (1) 2(t osc )(brg + 1) ? 93 t hd : sto stop condition 100 khz mode 2(t osc )(brg + 1) ? ns hold time 400 khz mode 2(t osc )(brg + 1) ? 1 mhz mode (1) 2(t osc )(brg + 1) ? note 1: maximum pin capacitance = 10 pf for all i 2 c? pins. note: refer to figure 26-4 for load conditions. 90 91 92 100 101 103 106 107 109 109 110 102 scl sda in sda out
? 2004 microchip technology inc. preliminary ds39629b-page 383 PIC18F6390/6490/8390/8490 table 26-20: master ssp i 2 c? bus data requirements param. no. symbol characteristic min max units conditions 100 t high clock high time 100 khz mode 2(t osc )(brg + 1) ? ms 400 khz mode 2(t osc )(brg + 1) ? ms 1 mhz mode (1) 2(t osc )(brg + 1) ? ms 101 t low clock low time 100 khz mode 2(t osc )(brg + 1) ? ms 400 khz mode 2(t osc )(brg + 1) ? ms 1 mhz mode (1) 2(t osc )(brg + 1) ? ms 102 t r sda and scl rise time 100 khz mode ? 1000 ns c b is specified to be from 10 to 400 pf 400 khz mode 20 + 0.1 c b 300 ns 1 mhz mode (1) ? 300 ns 103 t f sda and scl fall time 100 khz mode ? 300 ns c b is specified to be from 10 to 400 pf 400 khz mode 20 + 0.1 c b 300 ns 1 mhz mode (1) ? 100 ns 90 t su : sta start condition setup time 100 khz mode 2(t osc )(brg + 1) ? ms only relevant for repeated start condition 400 khz mode 2(t osc )(brg + 1) ? ms 1 mhz mode (1) 2(t osc )(brg + 1) ? ms 91 t hd : sta start condition hold time 100 khz mode 2(t osc )(brg + 1) ? ms after this period, the first clock pulse is generated 400 khz mode 2(t osc )(brg + 1) ? ms 1 mhz mode (1) 2(t osc )(brg + 1) ? ms 106 t hd : dat data input hold time 100 khz mode 0 ? ns 400 khz mode 0 0.9 ms 1 mhz mode (1) tbd ? ns 107 t su : dat data input setup time 100 khz mode 250 ? ns (note 2) 400 khz mode 100 ? ns 1 mhz mode (1) tbd ? ns 92 t su : sto stop condition setup time 100 khz mode 2(t osc )(brg + 1) ? ms 400 khz mode 2(t osc )(brg + 1) ? ms 1 mhz mode (1) 2(t osc )(brg + 1) ? ms 109 t aa output valid from clock 100 khz mode ? 3500 ns 400 khz mode ? 1000 ns 1 mhz mode (1) ??ns 110 t buf bus free time 100 khz mode 4.7 ? ms time the bus must be free before a new transmission can start 400 khz mode 1.3 ? ms 1 mhz mode (1) tbd ? ms d102 c b bus capacitive loading ? 400 pf note 1: maximum pin capacitance = 10 pf for all i 2 c? pins. 2: a fast mode i 2 c bus device can be used in a standard mode i 2 c bus system, but parameter #107 250 ns must then be met. this will automatically be the case if the device does not stretch the low period of the scl signal. if such a device does stretch the low period of the scl signal, it must output the next data bit to the sda line, parameter #102 + parameter #107 = 1000 + 250 = 1250 ns (for 100 khz mode,) before the scl line is released.
PIC18F6390/6490/8390/8490 ds39629b-page 384 preliminary ? 2004 microchip technology inc. figure 26-19: usart synchronous transmission (master/slave) timing table 26-21: usart synchronous transmission requirements figure 26-20: usart synchronous receive (master/slave) timing table 26-22: usart synchronous receive requirements 121 121 120 122 rc6/tx1/ck1 rc7/rx1/dt1 pin pin note: refer to figure 26-4 for load conditions. param no. symbol characteristic min max units conditions 120 t ck h2 dt v sync xmit (master and slave) clock high to data out valid pic18 f xxxx ? 40 ns pic18 lf xxxx ? 100 ns v dd = 2.0v 121 t ckrf clock out rise time and fall time (master mode) pic18 f xxxx ? 20 ns pic18 lf xxxx ? 50 ns v dd = 2.0v 122 t dtrf data out rise time and fall time pic18 f xxxx ? 20 ns pic18 lf xxxx ? 50 ns v dd = 2.0v 125 126 rc6/tx1/ck1 rc7/rx1/dt1 pin pin note: refer to figure 26-4 for load conditions. param. no. symbol characteristic min max units conditions 125 t dt v2 ckl sync rcv (master and slave) data hold before ck (dt hold time) 10 ? ns 126 t ck l2 dtl data hold after ck (dt hold time) 15 ? ns
? 2004 microchip technology inc. preliminary ds39629b-page 385 PIC18F6390/6490/8390/8490 table 26-23: a/d converter characteristics: pic18f2220/2320/4220/4320 (industrial) pic18lf2220/2320/4220/4320 (industrial) param no. symbol characteristic min typ max units conditions a01 n r resolution ? ? 10 bit ? v ref 3.0v a03 e il integral linearity error ? ? <1 lsb ? v ref 3.0v a04 e dl differential linearity error ? ? <1 lsb ? v ref 3.0v a06 e off offset error ? ? <1 lsb ? v ref 3.0v a07 e gn gain error ? ? <1 lsb ? v ref 3.0v a10 ? monotonicity guaranteed (1) ? a20 ? v ref reference voltage range (v refh ? v refl ) 3?av dd ? av ss v for 10-bit resolution a21 v refh reference voltage high av ss + 3.0v ? av dd + 0.3v v for 10-bit resolution a22 v refl reference voltage low av ss ? 0.3v ? av dd ? 3.0v v for 10-bit resolution a25 v ain analog input voltage v refl ?v refh v a30 z ain recommended impedance of analog voltage source ??2.5k ? a50 i ref v ref input current (note 2) ? ? ? ? 5 150 a a during v ain acquisition. during a/d conversion cycle. note 1: the a/d conversion result never decreases with an increase in the input voltage and has no missing codes. 2: v refh current is from ra3/an3/v ref +/seg17 pin or av dd , whichever is selected as the v refh source. v refl current is from ra2/an2/v ref -/seg16 pin or av ss , whichever is selected as the v refl source.
PIC18F6390/6490/8390/8490 ds39629b-page 386 preliminary ? 2004 microchip technology inc. figure 26-21: a/d conversion timing table 26-24: a/d conversion requirements 131 130 132 bsf adcon0, go q4 a/d clk a/d data adres adif go sample old_data sampling stopped done new_data (note 2) 987 21 0 note 1: if the a/d clock source is selected as rc, a time of t cy is added before the a/d clock starts. this allows the sleep instruction to be executed. 2: this is a minimal rc delay (typically 100 ns), which also disconnects the holding capacitor from the analog input. . . . . . . t cy param no. symbol characteristic min max units conditions 130 t ad a/d clock period pic18 f xxxx 0.7 25.0 (1) st osc based, v ref 3.0v pic18 lf xxxx 1.4 25.0 (1) sv dd = 2.0v; t osc based, v ref full range pic18 f xxxx tbd 1 s a/d rc mode pic18 lf xxxx tbd 3 sv dd = 2.0v; a/d rc mode 131 t cnv conversion time (not including acquisition time) (note 2) 11 12 t ad 132 t acq acquisition time (note 3) 1.4 tbd ? ? s s -40 c to +85 c 0 c to +85 c 135 t swc switching time from convert sample ? (note 4) tbd t dis discharge time 0.2 ? s legend: tbd = to be determined note 1: the time of the a/d clock period is dependent on the device frequency and the t ad clock divider. 2: adres register may be read on the following t cy cycle. 3: the time for the holding capacitor to acquire the ?new? input voltage when the voltage changes full scale after the conversion (v dd to v ss or v ss to v dd ). the source impedance ( r s ) on the input channels is 50 ? . 4: on the following cycle of the device clock.
? 2004 microchip technology inc. preliminary ds39629b-page 387 PIC18F6390/6490/8390/8490 27.0 dc and ac characteristics graphs and tables graphs and tables are not available at this time.
PIC18F6390/6490/8390/8490 ds39629b-page 388 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 389 PIC18F6390/6490/8390/8490 28.0 packaging information 28.1 package marking information 64-lead tqfp xxxxxxxxxx xxxxxxxxxx xxxxxxxxxx yywwnnn example pic18f6490 -i/pt 0410017 80-lead tqfp xxxxxxxxxxxx xxxxxxxxxxxx yywwnnn example pic18f8490-e /pt 0410017 legend: xx...x customer specific information* y year code (last digit of calendar year) yy year code (last 2 digits of calendar year) ww week code (week of january 1 is week ?01?) nnn alphanumeric traceability code note : in the event the full microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information. * standard picmicro device marking consists of microchip part number, year code, week code and traceability code. for picmicro device marking beyond this, certain price adders apply. please check with your microchip sales office. for qtp devices, any special marking adders are included in qtp price.
PIC18F6390/6490/8390/8490 ds39629b-page 390 preliminary ? 2004 microchip technology inc. 28.2 package details the following sections give the technical details of the packages. 64-lead plastic thin quad flatpack (pt) 10x10x1 mm body, 1.0/0.10 mm lead form (tqfp) 15 10 5 15 10 5 mold draft angle bottom 15 10 5 15 10 5 mold draft angle top 0.27 0.22 0.17 .011 .009 .007 b lead width 0.23 0.18 0.13 .009 .007 .005 c lead thickness 16 16 n1 pins per side 10.10 10.00 9.90 .398 .394 .390 d1 molded package length 10.10 10.00 9.90 .398 .394 .390 e1 molded package width 12.25 12.00 11.75 .482 .472 .463 d overall length 12.25 12.00 11.75 .482 .472 .463 e overall width 7 3.5 0 7 3.5 0 foot angle 0.75 0.60 0.45 .030 .024 .018 l foot length 0.25 0.15 0.05 .010 .006 .002 a1 standoff 1.05 1.00 0.95 .041 .039 .037 a2 molded package thickness 1.20 1.10 1.00 .047 .043 .039 a overall height 0.50 .020 p pitch 64 64 n number of pins max nom min max nom min dimension limits millimeters* inches units c 2 1 n d d1 b p #leads=n1 e1 e a2 a1 a l ch x 45 (f) footprint (reference) (f) .039 1.00 pin 1 corner chamfer ch .025 .035 .045 0.64 0.89 1.14 shall not exceed .010" (0.254mm) per side. dimensions d1 and e1 do not include mold flash or protrusions. mold flash or protrusions notes: jedec equivalent: ms-026 drawing no. c04-085 *controlling parameter
? 2004 microchip technology inc. preliminary ds39629b-page 391 PIC18F6390/6490/8390/8490 80-lead plastic thin quad flatpack (pt) 12x12x1 mm body, 1.0/0.10 mm lead form (tqfp) 1.10 1.00 .043 .039 1.14 0.89 0.64 .045 .035 .025 ch pin 1 corner chamfer 1.00 .039 (f) footprint (reference) (f) e e1 #leads=n1 p b d1 d n 1 2 c l a a1 a2 units inches millimeters* dimension limits min nom max min nom max number of pins n 80 80 pitch p .020 0.50 overall height a .047 1.20 molded package thickness a2 .037 .039 .041 0.95 1.00 1.05 standoff a1 .002 .004 .006 0.05 0.10 0.15 foot length l .018 .024 .030 0.45 0.60 0.75 foot angle 03.5 7 03.5 7 overall width e .541 .551 .561 13.75 14.00 14.25 overall length d .541 .551 .561 13.75 14.00 14.25 molded package width e1 .463 .472 .482 11.75 12.00 12.25 molded package length d1 .463 .472 .482 11.75 12.00 12.25 pins per side n1 20 20 lead thickness c .004 .006 .008 0.09 0.15 0.20 lead width b .007 .009 .011 0.17 0.22 0.27 mold draft angle top 5 10 15 5 10 15 mold draft angle bottom 5 10 15 5 10 15 ch x 45 shall not exceed .010" (0.254mm) per side. dimensions d1 and e1 do not include mold flash or protrusions. mold flash or protrusions notes: jedec equivalent: ms-026 drawing no. c04-092 *controlling parameter
PIC18F6390/6490/8390/8490 ds39629b-page 392 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 393 PIC18F6390/6490/8390/8490 appendix a: revision history revision a (july 2004) original data sheet for PIC18F6390/6490/8390/8490 devices. appendix b: device differences the differences between the devices listed in this data sheet are shown in table b-1. table b-1: device differences features PIC18F6390 pic18f6490 pic18f8390 pic18f8490 number of pixels the lcd driver can drive 128 (4 x 32) 128 (4 x 32) 192 (4 x 48) 192 (4 x 48) i/o ports ports a, b, c, d, e, f, g ports a, b, c, d, e, f, g ports a, b, c, d, e, f, g, h, j ports a, b, c, d, e, f, g, h, j flash program memory 8 kbytes 16 kbytes 8 kbytes 16 kbytes packages 64-pin tqfp 64-pin tqfp 80-pin tqfp 80-pin tqfp
PIC18F6390/6490/8390/8490 ds39629b-page 394 preliminary ? 2004 microchip technology inc. appendix c: conversion considerations this appendix discusses the considerations for converting from previous versions of a device to the ones listed in this data sheet. typically, these changes are due to the differences in the process technology used. an example of this type of conversion is from a pic16c74a to a pic16c74b. not applicable appendix d: migration from baseline to enhanced devices this section discusses how to migrate from a baseline device (i.e., pic16c5x) to an enhanced mcu device (i.e., pic18fxxx). the following are the list of modifications over the pic16c5x microcontroller family: not currently available
? 2004 microchip technology inc. preliminary ds39629b-page 395 PIC18F6390/6490/8390/8490 appendix e: migration from mid-range to enhanced devices a detailed discussion of the differences between the mid-range mcu devices (i.e., pic16cxxx) and the enhanced devices (i.e., pic18fxxx) is provided in an716, ?migrating designs from pic16c74a/74b to pic18c442.? the changes discussed, while device specific, are generally applicable to all mid-range to enhanced device migrations. this application note is available as literature number ds00716. appendix f: migration from high-end to enhanced devices a detailed discussion of the migration pathway and differences between the high-end mcu devices (i.e., pic17cxxx) and the enhanced devices (i.e., pic18fxxx) is provided in an726, ?pic17cxxx to pic18cxxx migration.? this application note is available as literature number ds00726.
PIC18F6390/6490/8390/8490 ds39629b-page 396 preliminary ? 2004 microchip technology inc. notes:
? 2004 microchip technology inc. preliminary ds39629b-page 397 PIC18F6390/6490/8390/8490 index a a/d ................................................................................... 231 a/d converter interrupt, configuring ....................... 235 acquisition requirements ........................................ 236 adcon0 register .................................................... 231 adcon1 register .................................................... 231 adcon2 register .................................................... 231 adresh register ............................................ 231, 234 adresl register .................................................... 231 analog port pins, configuring .................................. 238 associated registers ............................................... 240 automatic acquisition time ...................................... 237 calculating the minimum required acquisition time .............................................. 236 configuring the module ............................................ 235 conversion clock (t ad ) ........................................... 237 conversion requirements ....................................... 386 conversion status (go/done bit) .......................... 234 conversions ............................................................. 239 converter characteristics ........................................ 385 operation in power managed modes ...................... 238 special event trigger (ccp) .................................... 240 use of the ccp2 trigger .......................................... 240 absolute maximum ratings ............................................. 351 ac (timing) characteristics ............................................. 368 load conditions for device timing specifications ....................................... 369 parameter symbology ............................................. 368 temperature and voltage specific ations ................. 369 timing conditions .................................................... 369 access bank ...................................................................... 73 mapping with indexed literal offset mode ................. 86 ackstat ........................................................................ 187 ackstat status flag ..................................................... 187 adcon0 register ............................................................ 231 go/done bit ........................................................... 234 adcon1 register ............................................................ 231 adcon2 register ............................................................ 231 addfsr .......................................................................... 338 addlw ............................................................................ 301 addressable universal synchronous asynchronous receiver transmitter (ausart). see ausart. addulnk ........................................................................ 338 addwf ............................................................................ 301 addwfc ......................................................................... 302 adresh register ............................................................ 231 adresl register .................................................... 231, 234 analog-to-digital converter. see a/d. andlw ............................................................................ 302 andwf ............................................................................ 303 assembler mpasm assembler .................................................. 345 ausart asynchronous mode ................................................ 222 associated registers, receive ........................ 225 associated registers, transmit ....................... 223 receiver ........................................................... 224 setting up 9-bit mode with address detect ........................................ 224 transmitter ....................................................... 222 baud rate generator (brg) ................................... 220 associated registers ....................................... 220 baud rate error, calculating ........................... 220 baud rates, asynchronous modes ................. 221 high baud rate select (brgh bit) ................. 220 operation in power managed modes .............. 220 sampling ......................................................... 220 synchronous master mode ...................................... 226 associated registers, receive ........................ 228 associated registers, transmit ....................... 227 reception ........................................................ 228 transmission ................................................... 226 synchronous slave mode ........................................ 229 associated registers, receive ........................ 230 associated registers, transmit ....................... 229 reception ........................................................ 230 transmission ................................................... 229 auto-wake-up on sync break character ......................... 210 b bank select register (bsr) .............................................. 71 baud rate generator ...................................................... 183 bc .................................................................................... 303 bcf ................................................................................. 304 bf .................................................................................... 187 bf status flag ................................................................. 187 block diagrams a/d ........................................................................... 234 analog input model .................................................. 235 ausart receive .................................................... 224 ausart transmit ................................................... 222 baud rate generator .............................................. 183 capture mode operation ......................................... 150 comparator i/o operating modes (diagram) ...................... 242 comparator analog input model .............................. 245 comparator output .................................................. 244 comparator voltage reference ............................... 248 compare mode operation ....................................... 151 device clock .............................................................. 36 eusart receive .................................................... 208 eusart transmit ................................................... 206 external power-on reset circuit (slow v dd power-up) ........................................ 53 fail-safe clock monitor ........................................... 290 generic i/o port operation ...................................... 109 hlvd module (with external input) ......................... 252 interrupt logic ............................................................ 94 lcd clock generation ............................................. 262 lcd driver module .................................................. 257 lcd resistor ladder connection ............................ 263 mssp (i 2 c master mode) ........................................ 181 mssp (i 2 c mode) .................................................... 166 mssp (spi mode) ................................................... 157 on-chip reset circuit ................................................ 51 pll (hs mode) .......................................................... 33 pwm operation (simplified) .................................... 153 reads from flash program memory ......................... 88 single comparator ................................................... 243 table read operation ............................................... 87 timer0 in 16-bit mode ............................................. 132 timer0 in 8-bit mode ............................................... 132 timer1 ..................................................................... 136
PIC18F6390/6490/8390/8490 ds39629b-page 398 preliminary ? 2004 microchip technology inc. timer1 (16-bit read/write mode) ............................ 136 timer2 ...................................................................... 142 timer3 ...................................................................... 144 timer3 (16-bit read/write mode) ............................ 144 voltage reference output buffer example .............. 249 watchdog timer ....................................................... 287 bn .................................................................................... 304 bnc .................................................................................. 305 bnn .................................................................................. 305 bnov ............................................................................... 306 bnz .................................................................................. 306 bor. see brown-out reset. bov .................................................................................. 309 bra .................................................................................. 307 break character (12-bit) transmit and receive .............. 211 brg. see baud rate generator. brown-out reset (bor) ............................................. 54, 281 disabling in sleep mode ............................................ 54 bsf .................................................................................. 307 bsr .................................................................................... 86 btfsc ............................................................................. 308 btfss .............................................................................. 308 btg .................................................................................. 309 bz ..................................................................................... 310 c c compilers mplab c17 ............................................................. 346 mplab c18 ............................................................. 346 mplab c30 ............................................................. 346 call ................................................................................ 310 callw ............................................................................. 339 capture (ccp module) ..................................................... 150 associated registers ............................................... 152 ccp pin configuration ............................................. 150 ccpr2h:ccpr2l registers ................................... 150 software interrupt .................................................... 150 timer1/timer3 mode selection ................................ 150 capture/compare/pwm (ccp) ........................................ 147 capture mode. see capture. ccp mode and timer resources ............................ 148 ccprxh register .................................................... 148 ccprxl register ..................................................... 148 compare mode. see compare. interaction of ccp1 and ccp2 for timer resources .............................................. 149 interconnect configurations ..................................... 148 module configuration ............................................... 148 clock sources .................................................................... 36 selecting the 31 khz source ...................................... 37 selection using osccon register ........................... 37 clrf ................................................................................ 311 clrwdt .......................................................................... 311 code examples 16 x 16 signed multiply routine ................................ 92 16 x 16 unsigned multiply routine ............................ 92 8 x 8 signed multiply routine .................................... 91 8 x 8 unsigned multiply routine ................................ 91 changing between capture prescalers ................... 150 computed goto using an offset value ................... 68 fast register stack .................................................... 68 how to clear ram (bank 1) using indirect addressing ............................................ 81 implementing a real-time clock using a timer1 interrupt service ............................... 139 initializing porta .................................................... 109 initializing portb .................................................... 112 initializing portc ................................................... 115 initializing portd ................................................... 118 initializing porte .................................................... 120 initializing portf .................................................... 122 initializing portg ................................................... 125 initializing porth ................................................... 127 initializing portj .................................................... 129 loading the sspbuf (sspsr) register ................. 160 reading a flash program memory word .................. 89 saving status, wreg and bsr registers in ram .................................... 108 code protection ............................................................... 281 comf .............................................................................. 312 comparator ...................................................................... 241 analog input connection considerations ................ 245 associated registers ............................................... 245 configuration ........................................................... 242 effects of a reset .................................................... 244 interrupts ................................................................. 244 operation ................................................................. 243 operation during sleep ........................................... 244 outputs .................................................................... 243 reference ................................................................ 243 external signal ................................................ 243 internal signal .................................................. 243 response time ........................................................ 243 comparator specifications ............................................... 366 comparator voltage reference ....................................... 247 accuracy and error .................................................. 248 associated registers ............................................... 249 configuring .............................................................. 247 connection considerations ...................................... 248 effects of a reset .................................................... 248 operation during sleep ........................................... 248 compare (ccp module) .................................................. 151 associated registers ............................................... 152 ccp pin configuration ............................................. 151 ccpr2 register ...................................................... 151 software interrupt .................................................... 151 special event trigger .............................. 145, 151, 240 timer1/timer3 mode selection ................................ 151 computed goto ............................................................... 68 configuration bits ............................................................ 281 configuration register protection .................................... 292 context saving during interrupts ..................................... 108 conversion considerations .............................................. 394 cpfseq .......................................................................... 312 cpfsgt .......................................................................... 313 cpfslt ........................................................................... 313 crystal oscillator/cerami c resonator ................................ 31 d data addressing modes .................................................... 81 comparing addressing modes with the extended instruction set enabled ..................... 85 direct ......................................................................... 81 indexed literal offset ................................................ 84 indirect ....................................................................... 81 inherent and literal .................................................... 81
? 2004 microchip technology inc. preliminary ds39629b-page 399 PIC18F6390/6490/8390/8490 data memory ..................................................................... 71 access bank .............................................................. 73 and the extended instruction set ............................... 84 bank select register (bsr) ....................................... 71 general purpose registers ........................................ 73 map for pic18f6x90/8x90 devices .......................... 72 special function registers ........................................ 74 daw ................................................................................. 314 dc and ac characteristics graphs and tables .................................................. 387 dc characteristics ........................................................... 363 power-down and supply current ............................ 354 supply voltage ......................................................... 353 dcfsnz .......................................................................... 315 decf ............................................................................... 314 decfsz ........................................................................... 315 demonstration boards picdem 1 ................................................................ 348 picdem 17 .............................................................. 349 picdem 18r ........................................................... 349 picdem 2 plus ........................................................ 348 picdem 3 ................................................................ 348 picdem 4 ................................................................ 348 picdem lin ............................................................ 349 picdem usb ........................................................... 349 picdem.net internet/ethernet ................................. 348 development support ...................................................... 345 device differences ........................................................... 393 device overview .................................................................. 7 features (table) ............................................................ 9 new core features ...................................................... 7 special features .......................................................... 8 direct addressing ............................................................... 82 e effect on standard pic instructions ........................... 84, 342 effects of power managed modes on various clock sources ............................................... 39 electrical characteristics .................................................. 351 enhanced universal synchronous asynchronous receiver transmitter (eusart). see eusart. equations a/d acquisition time ................................................ 236 a/d minimum charging time ................................... 236 errata ................................................................................... 5 eusart asynchronous mode ................................................ 206 12-bit break transmit and receive ................. 211 associated registers, receive ........................ 209 associated registers, transmit ....................... 207 auto-wake-up on sync break ......................... 210 receiver ........................................................... 208 setting up 9-bit mode with address detect ........................................ 208 transmitter ....................................................... 206 baud rate generator (brg) .................................... 201 associated registers ....................................... 201 auto-baud rate detect .................................... 204 baud rate error, calculating ........................... 201 baud rates, asynchronous modes ................. 202 high baud rate select (brgh bit) ................. 201 sampling .......................................................... 201 synchronous master mode ...................................... 212 associated registers, receive ........................ 214 associated registers, transmit ....................... 213 reception ........................................................ 214 transmission ................................................... 212 synchronous slave mode ........................................ 215 associated registers, receive ........................ 216 associated registers, transmit ....................... 215 reception ........................................................ 216 transmission ................................................... 215 evaluation and programming tools ................................. 349 extended instruction set addfsr .................................................................. 338 addulnk ............................................................... 338 callw .................................................................... 339 movsf .................................................................... 339 movss .................................................................... 340 pushl ..................................................................... 340 subfsr .................................................................. 341 subulnk ................................................................ 341 external clock input ........................................................... 32 f fail-safe clock monitor ........................................... 281, 290 interrupts in power managed modes .............................................. 291 por or wake from sleep ........................................ 291 wdt during oscillator failure ................................. 290 fast register stack ........................................................... 68 firmware instructions ...................................................... 295 flash program memory ..................................................... 87 associated registers ................................................. 89 control registers ....................................................... 88 tablat (table latch) register ........................ 88 tblptr (table pointer) register ...................... 88 reading ..................................................................... 88 table reads .............................................................. 87 fscm. see fail-safe clock monitor. g goto .............................................................................. 316 h hardware multiplier ............................................................ 91 introduction ................................................................ 91 operation ................................................................... 91 performance comparison .......................................... 91 high/low-voltage detect ................................................. 251 applications ............................................................. 254 typical low-voltage detect (diagram) ...................................... 254 associated registers ............................................... 255 current consumption .............................................. 253 effects of a reset .................................................... 255 operation ................................................................. 252 during sleep .................................................... 255 setup ....................................................................... 253 start-up time ........................................................... 253 hlvd. see high/low-voltage detect.
PIC18F6390/6490/8390/8490 ds39629b-page 400 preliminary ? 2004 microchip technology inc. i i/o ports ........................................................................... 109 i 2 c mode (mssp) acknowledge sequence timing ............................... 190 associated registers ............................................... 196 baud rate generator ............................................... 183 bus collision during a repeated start condition .................. 194 during a start condition ................................... 192 during a stop condition ................................... 195 clock arbitration ....................................................... 184 clock stretching ....................................................... 176 10-bit slave receive mode (sen = 1) ............. 176 7-bit slave receive mode (sen = 1) ............... 176 effect of a reset ...................................................... 191 general call address support ................................. 180 i 2 c clock rate w/brg ............................................. 183 master mode ............................................................ 181 operation ......................................................... 182 reception ......................................................... 187 repeated start condition timing ..................... 186 start condition ................................................. 185 transmission .................................................... 187 transmit sequence .......................................... 182 multi-master communication, bus collision and arbitration .................................................. 191 multi-master mode ................................................... 191 operation ................................................................. 170 read/write bit information (r/w bit) ............... 170, 171 registers .................................................................. 166 serial clock (rc3/sck/scl) ................................... 171 slave mode .............................................................. 170 addressing ....................................................... 170 reception ......................................................... 171 sleep operation ....................................................... 191 stop condition timing .............................................. 190 transmission ............................................................ 171 id locations ............................................................. 281, 293 incf ................................................................................. 316 incfsz ............................................................................ 317 in-circuit debugger .......................................................... 293 in-circuit serial programming (icsp) ...................... 281, 293 indexed literal offset addressing mode .......................... 342 and standard pic18 instructions ............................. 342 indexed literal offset mode ......................................... 84, 86 indirect addressing ............................................................ 82 infsnz ............................................................................ 317 initialization conditions for all registers ...................... 59?64 instruction cycle ................................................................. 69 clocking scheme ....................................................... 69 instruction flow/pipelining ................................................. 69 instruction set .................................................................. 295 addlw .................................................................... 301 addwf .................................................................... 301 addwf (indexed literal offset mode) .................... 343 addwfc ................................................................. 302 andlw .................................................................... 302 andwf .................................................................... 303 bc ............................................................................ 303 bcf .......................................................................... 304 bn ............................................................................ 304 bnc ......................................................................... 305 bnn ......................................................................... 305 bnov ....................................................................... 306 bnz .......................................................................... 306 bov ......................................................................... 309 bra ......................................................................... 307 bsf .......................................................................... 307 bsf (indexed literal offset mode) .......................... 343 btfsc ..................................................................... 308 btfss ..................................................................... 308 btg ......................................................................... 309 bz ............................................................................ 310 call ........................................................................ 310 clrf ....................................................................... 311 clrwdt ................................................................. 311 comf ...................................................................... 312 cpfseq .................................................................. 312 cpfsgt .................................................................. 313 cpfslt ................................................................... 313 daw ........................................................................ 314 dcfsnz .................................................................. 315 decf ....................................................................... 314 decfsz .................................................................. 315 extended instructions .............................................. 337 and using mplab tools ................................. 344 considerations when enabling ........................ 342 syntax .............................................................. 337 general format ........................................................ 297 goto ...................................................................... 316 incf ........................................................................ 316 incfsz .................................................................... 317 infsnz .................................................................... 317 iorlw ..................................................................... 318 iorwf ..................................................................... 318 lfsr ....................................................................... 319 movf ...................................................................... 319 movff .................................................................... 320 movlb .................................................................... 320 movlw ................................................................... 321 movwf ................................................................... 321 mullw .................................................................... 322 mulwf .................................................................... 322 negf ....................................................................... 323 nop ......................................................................... 323 pop ......................................................................... 324 push ....................................................................... 324 rcall ..................................................................... 325 reset ..................................................................... 325 retfie .................................................................... 326 retlw .................................................................... 326 return .................................................................. 327 rlcf ....................................................................... 327 rlncf ..................................................................... 328 rrcf ....................................................................... 328 rrncf ................................ .................................... 329 setf ....................................................................... 329 setf (indexed literal offset mode) ........................ 343 sleep ..................................................................... 330 standard instructions ............................................... 295 subfwb ................................................................. 330 sublw .................................................................... 331 subwf .................................................................... 331 subwfb ................................................................. 332 swapf .................................................................... 332 tblrd ..................................................................... 333 tblwt .................................................................... 334 tstfsz ................................................................... 335 xorlw ................................................................... 335 xorwf ................................................................... 336 summary table ....................................................... 298
? 2004 microchip technology inc. preliminary ds39629b-page 401 PIC18F6390/6490/8390/8490 intcon register rbif bit .................................................................... 112 intcon registers ............................................................. 95 inter-integrated circuit. see i 2 c. internal oscillator block ..................................................... 34 adjustment ................................................................. 34 intio modes .............................................................. 34 intosc output frequency ........................................ 34 osctune register ................................................... 34 internal rc oscillator use with wdt .......................................................... 287 interrupt sources ............................................................. 281 a/d conversion complete ....................................... 235 capture complete (ccp) ......................................... 150 compare complete (ccp) ....................................... 151 interrupt-on-change (rb7:rb4) .............................. 112 intn pin ................................................................... 108 portb, interrupt-on-change .................................. 108 tmr0 ....................................................................... 108 tmr0 overflow ........................................................ 133 tmr1 overflow ........................................................ 135 tmr2 to pr2 match (pwm) .................................... 153 tmr3 overflow ................................................ 143, 145 interrupts ............................................................................ 93 interrupts, flag bits interrupt-on-change (rb7:rb4) flag (rbif bit) ................................................. 112 intosc frequency drift .................................................... 34 intosc, intrc. see internal oscillator block. iorlw ............................................................................. 318 iorwf ............................................................................. 318 ipr registers ................................................................... 104 l lcd associated registers ............................................... 279 bias types ............................................................... 263 clock source selection ............................................ 262 configuring the module ............................................ 278 frame frequency ..................................................... 264 interrupts .................................................................. 276 lcdcon register ................................................... 258 lcddata register .................................................. 258 lcdps register ....................................................... 258 lcdse register ....................................................... 258 multiplex types ........................................................ 263 operation during sleep ........................................... 277 pixel control ............................................................. 264 prescaler .................................................................. 262 segment enables ..................................................... 263 waveform generation .............................................. 264 lcdcon register ........................................................... 258 lcddata register .......................................................... 258 lcdps register ............................................................... 258 lp3:lp0 bits ............................................................ 262 lcdse register ............................................................... 258 lfsr ................................................................................ 319 liquid crystal display (lcd) driver ................................. 257 look-up tables .................................................................. 68 low-voltage detect characteristics ......................................................... 367 m master clear (mclr ) ......................................................... 53 master synchronous serial port (mssp). see mssp. memory organization ........................................................ 65 data memory ............................................................. 71 program memory ....................................................... 65 memory programming requirements .............................. 365 migration from baseline to enhanced devices ................ 394 migration from high-end to enhanced devices ............... 395 migration from mid-range to enhanced devices ............ 395 movf .............................................................................. 319 movff ............................................................................ 320 movlb ............................................................................ 320 movlw ........................................................................... 321 movsf ............................................................................ 339 movss ............................................................................ 340 movwf ........................................................................... 321 mplab asm30 assembler, linker, librarian .................. 346 mplab icd 2 in-circuit debugger .................................. 347 mplab ice 2000 high-performance universal in-circuit emulator ................................... 347 mplab ice 4000 high-performance universal in-circuit emulator ................................... 347 mplab integrated development environment software ............................................. 345 mplab pm3 device programmer ................................... 347 mplink object linker/mplib object librarian ............... 346 mssp ack pulse ....................................................... 170, 171 control registers (general) ..................................... 157 i 2 c mode. see i 2 c mode. module overview ..................................................... 157 spi master/slave connection .................................. 161 spi mode. see spi mode. sspbuf .................................................................. 162 sspsr .................................................................... 162 mullw ............................................................................ 322 mulwf ............................................................................ 322 n negf ............................................................................... 323 nop ................................................................................. 323 o opcode field descriptions ............................................... 296 option_reg register psa bit .................................................................... 133 t0cs bit .................................................................. 132 t0ps2:t0ps0 bits ................................................... 133 t0se bit .................................................................. 132 oscillator configuration ................ ..................................... 31 ec .............................................................................. 31 ecio .......................................................................... 31 hs .............................................................................. 31 hspll ....................................................................... 31 internal oscillator block ............................................. 34 intio1 ....................................................................... 31 intio2 ....................................................................... 31 lp .............................................................................. 31 rc ............................................................................. 31 rcio .......................................................................... 31 xt .............................................................................. 31
PIC18F6390/6490/8390/8490 ds39629b-page 402 preliminary ? 2004 microchip technology inc. oscillator selection .......................................................... 281 oscillator start-up timer (ost) ........................... 39, 55, 281 oscillator switching ............................................................ 36 oscillator transitions .......................................................... 37 oscillator, timer1 ..................................................... 135, 145 oscillator, timer3 ............................................................. 143 p packaging ........................................................................ 389 details ...................................................................... 390 marking .................................................................... 389 pickit 1 flash starter kit .................................................. 349 picstart plus development programmer .................... 348 pie registers ................................................................... 101 pin functions av dd .......................................................................... 29 av dd .......................................................................... 19 av ss .......................................................................... 29 av ss .......................................................................... 19 com0 ................................................................... 17, 25 lcdbias1 ............................................................ 17, 25 lcdbias2 ............................................................ 17, 25 lcdbias3 ............................................................ 17, 25 mclr /v pp /rg5 ................................................... 12, 20 osc1/clki/ra7 .................................................. 12, 20 osc2/clko/ra6 ................................................ 12, 20 ra0/an0 .............................................................. 13, 21 ra1/an1 .............................................................. 13, 21 ra2/an2/v ref -/seg16 ....................................... 13, 21 ra3/an3/v ref +/seg17 ...................................... 13, 21 ra4/t0cki/seg14 .............................................. 13, 21 ra5/an4/hlvdin/seg15 ................................... 13, 21 rb0/int0 ............................................................. 14, 22 rb1/int1/seg8 ................................................... 14, 22 rb2/int2/seg9 ................................................... 14, 22 rb3/int3/seg10 ................................................. 14, 22 rb4/kbi0/seg11 ................................................. 14, 22 rb5/kbi1 ............................................................. 14, 22 rb6/kbi2/pgc .................................................... 14, 22 rb7/kbi3/pgd .................................................... 14, 22 rc0/t1oso/t13cki ........................................... 15, 23 rc1/t1osi/ccp2 ................................................ 15, 23 rc2/ccp1/seg13 ............................................... 15, 23 rc3/sck/scl ..................................................... 15, 23 rc4/sdi/sda ...................................................... 15, 23 rc5/sdo/seg12 ................................................ 15, 23 rc6/tx1/ck1 ...................................................... 15, 23 rc7/rx1/dt1 ...................................................... 15, 23 rd0/seg0 ........................................................... 16, 24 rd0/seg1 ................................................................. 16 rd1/seg1 ................................................................. 24 rd2/seg2 ........................................................... 16, 24 rd3/seg3 ........................................................... 16, 24 rd4/seg4 ........................................................... 16, 24 rd5/seg5 ........................................................... 16, 24 rd6/seg6 ........................................................... 16, 24 rd7/seg7 ........................................................... 16, 24 re4/com1 ........................................................... 17, 25 re5/com2 ........................................................... 17, 25 re6/com3 ........................................................... 17, 25 re7/ccp2/seg31 ............................................... 17, 25 rf0/an5/seg18 .................................................. 18, 26 rf1/an6/c2out/seg19 .................................... 18, 26 rf2/an7/c1out/seg20 .................................... 18, 26 rf3/an8/seg21 ................................................. 18, 26 rf4/an9/seg22 ................................................. 18, 26 rf5/an10/cv ref /seg23 .................................... 18, 26 rf6/an11/seg24 ............................................... 18, 26 rf7/ss /seg25 ................................................... 18, 26 rg0/seg30 ......................................................... 19, 27 rg1/tx2/ck2/seg29 ......................................... 19, 27 rg2/rx2/dt2/seg28 ......................................... 19, 27 rg3/seg27 ......................................................... 19, 27 rg4/seg26 ......................................................... 19, 27 rg5 ..................................................................... 19, 27 rh0/seg47 ............................................................... 28 rh1/seg46 ............................................................... 28 rh2/seg45 ............................................................... 28 rh3/seg44 ............................................................... 28 rh4/seg40 ............................................................... 28 rh5/seg41 ............................................................... 28 rh6/seg42 ............................................................... 28 rh7/seg43 ............................................................... 28 rj0/seg32 ................................................................ 29 rj1/seg33 ................................................................ 29 rj2/seg34 ................................................................ 29 rj3/seg35 ................................................................ 29 rj4/seg39 ................................................................ 29 rj5/seg38 ................................................................ 29 rj6/seg37 ................................................................ 29 rj7/seg36 ................................................................ 29 v dd ............................................................................ 29 v dd ............................................................................ 19 v ss ............................................................................ 29 v ss ............................................................................ 19 pinout i/o descriptions pic18f6x90 .............................................................. 12 pic18f8x90 .............................................................. 20 pir registers ..................................................................... 98 pll .................................................................................... 33 hspll oscillator mode ............................................. 33 use with intosc ................................................ 33, 34 pll lock time-out ............................................................. 55 pop ................................................................................. 324 por. see power-on reset. porta associated registers ............................................... 111 lata register ......................................................... 109 porta register ...................................................... 109 trisa register ........................................................ 109 portb associated registers ............................................... 114 latb register ......................................................... 112 portb register ...................................................... 112 rb7:rb4 interrupt-on-change flag (rbif bit) ................................................. 112 trisb register ........................................................ 112 portc associated registers ............................................... 117 latc register ......................................................... 115 portc register ...................................................... 115 rc3/sck/scl pin ................................................... 171 trisc register ........................................................ 115 portd associated registers ............................................... 119 latd register ......................................................... 118 portd register ...................................................... 118 trisd register ........................................................ 118
? 2004 microchip technology inc. preliminary ds39629b-page 403 PIC18F6390/6490/8390/8490 porte associated registers ............................................... 121 late register .......................................................... 120 porte register ...................................................... 120 trise register ........................................................ 120 portf associated registers ............................................... 124 latf register .......................................................... 122 portf register ...................................................... 122 trisf register ........................................................ 122 portg associated registers ............................................... 126 latg register ......................................................... 125 portg register ...................................................... 125 trisg register ........................................................ 125 porth associated registers ............................................... 128 lath register ......................................................... 127 porth register ...................................................... 127 trish register ........................................................ 127 portj associated registers ............................................... 130 latj register .......................................................... 129 portj register ....................................................... 129 trisj register ......................................................... 129 postscaler, wdt assignment (psa bit) .............................................. 133 rate select (t0ps2:t0ps0 bits) ............................. 133 switching between timer0 and wdt ...................... 133 power managed modes ..................................................... 41 and multiple sleep commands .................................. 42 entering ...................................................................... 41 exiting idle and sleep modes by reset ............................................................. 48 by wdt time-out ............................................... 48 without a start-up delay .................................... 48 exiting idle or sleep modes ....................................... 48 by interrupt ......................................................... 48 idle modes ................................................................. 45 pri_idle ........................................................... 46 run modes ................................................................. 42 pri_run ........................................................... 42 rc_run ............................................................ 44 sec_run .......................................................... 42 selecting .................................................................... 41 sleep mode ................................................................ 45 summary (table) ........................................................ 41 power-on reset (por) .............................................. 53, 281 oscillator start-up timer (ost) ................................. 55 power-up timer (pwrt) ................................... 55, 281 time-out sequence .................................................... 55 power-up delays ................................................................ 39 power-up timer (pwrt) ............................................. 39, 55 prescaler, capture ........................................................... 150 prescaler, timer0 ............................................................. 133 assignment (psa bit) .............................................. 133 rate select (t0ps2:t0ps0 bits) ............................. 133 switching between timer0 and wdt ...................... 133 prescaler, timer2 ............................................................. 154 pro mate ii universal device programmer ................................................. 347 program counter ............................................................... 66 pcl, pch and pcu registers ................................... 66 pclath and pclatu registers .............................. 66 program memory and extended instruction set .................................... 84 instructions ................................................................ 70 two-word .......................................................... 70 interrupt vector .......................................................... 65 map and stack (diagram) .......................................... 65 reset vector .............................................................. 65 program verification and code protection ...................... 292 associated registers ............................................... 292 programming, device instructions ................................... 295 pulse width modulation. see pwm (ccp module). push ............................................................................... 324 push and pop instructions .............................................. 67 pushl ............................................................................. 340 pwm (ccp module) associated registers ............................................... 155 duty cycle ............................................................... 154 example frequencies/resolutions .......................... 154 period ...................................................................... 153 setup for pwm operation ....................................... 155 tmr2 to pr2 match ................................................ 153 q q clock ............................................................................ 154 r ram. see data memory. rc oscillator ...................................................................... 33 rcio oscillator mode ................................................ 33 rcall ............................................................................. 325 rcon register bit status during initialization .................................... 58 reading program memory and other locations ............. 292 register file ....................................................................... 73 register file summary ................................................ 76?79 registers adcon0 (a/d control 0) ......................................... 231 adcon1 (a/d control 1) ......................................... 232 adcon2 (a/d control 2) ......................................... 233 baudcon1 (baud rate control 1) ......................... 200 ccpxcon (capture/compare/pwm control - ccp1, ccp2) ................................... 147 cmcon (comparator control) ................................ 241 config1h (configuration 1 high) .......................... 282 config2h (configuration 2 high) .......................... 284 config2l (configuration 2 low) ........................... 283 config3h (configuration 3 high) .......................... 284 config4l (configuration 4 low) ........................... 285 config5l (configuration 5 low) ........................... 285 cvrcon (comparator voltage reference control) .......................................... 247 device id 1 .............................................................. 286 device id 2 .............................................................. 286 hlvdcon (hlvd control) ..................................... 251 intcon (interrupt control) ....................................... 95 intcon2 (interrupt control 2) .................................. 96 intcon3 (interrupt control 3) .................................. 97 ipr1 (peripheral interrupt priority 1) ....................... 104 ipr2 (peripheral interrupt priority 2) ....................... 105 ipr3 (peripheral interrupt priority 3) ....................... 106 lcdcon (lcd control) .......................................... 258 lcddatax (lcd data) ........................................... 261 lcdps (lcd phase) ............................................... 259 lcdsex (lcd segment enable) ............................. 260
PIC18F6390/6490/8390/8490 ds39629b-page 404 preliminary ? 2004 microchip technology inc. osccon (oscillator control) .................................... 38 osctune (oscillator tuning) ................................... 35 pie1 (peripheral interrupt enable 1) ........................ 101 pie2 (peripheral interrupt enable 2) ........................ 102 pie3 (peripheral interrupt enable 3) ........................ 103 pir1 (peripheral interrupt request (flag) 1) ............................................... 98 pir2 (peripheral interrupt request (flag) 2) ............................................... 99 pir3 (peripheral interrupt request (flag) 3) ............................................. 100 rcon (reset control) ....................................... 52, 107 rcsta1 (eusart receive status and control) ..................................................... 199 rcsta2 (ausart receive status and control) ..................................................... 219 sspcon1 (mssp control 1, i 2 c mode) ................. 168 sspcon1 (mssp control 1, spi mode) ................. 159 sspcon2 (mssp control 2, i 2 c mode) ................. 169 sspstat (mssp status, i 2 c mode) ....................... 167 sspstat (mssp status, spi mode) ...................... 158 status ......................................................................... 80 stkptr (stack pointer) ............................................ 67 t0con (timer0 control) .......................................... 131 t1con (timer1 control) .......................................... 135 t2con (timer 2 control) ......................................... 141 t3con (timer3 control) .......................................... 143 txsta1 (eusart transmit status and control) ..................................................... 198 txsta2 (ausart transmit status and control) ..................................................... 218 wdtcon (watchdog timer control) ....................... 288 reset ............................................................................. 325 reset .................................................................................. 51 mclr reset, during power managed modes ................................................ 51 mclr reset, normal operation ................................ 51 power-on reset (por) .............................................. 51 programmable brown-out reset (bor) ...................................................... 51 stack full reset ......................................................... 51 stack underflow reset .............................................. 51 watchdog timer (wdt) reset ................................... 51 resets .............................................................................. 281 retfie ............................................................................ 326 retlw ............................................................................. 326 return .......................................................................... 327 return address stack ........................................................ 66 return stack pointer (stkptr) ........................................ 67 revision history ............................................................... 393 rlcf ................................................................................ 327 rlncf ............................................................................. 328 rrcf ............................................................................... 328 rrncf ........................ ..................................................... 329 s sck .................................................................................. 157 sdi ................................................................................... 157 sdo ................................................................................. 157 serial clock, sck ............................................................. 157 serial data in (sdi) .......................................................... 157 serial data out (sdo) ..................................................... 157 serial peripheral interface. see spi mode. setf ................................................................................ 329 slave select (ss ) ............................................................. 157 sleep ............................................................................. 330 sleep osc1 and osc2 pin states ...................................... 39 software enabled bor ...................................................... 54 software simulator (mplab sim) ................................... 346 software simulator (mplab sim30) ............................... 346 special event trigger. see compare (ccp module). special features of the cpu ........................................... 281 special function registers ................................................ 74 map ...................................................................... 74?75 spi mode (mssp) associated registers ............................................... 165 bus mode compatibility ........................................... 165 effects of a reset .................................................... 165 enabling spi i/o ...................................................... 161 master mode ............................................................ 162 master/slave connection ......................................... 161 operation ................................................................. 160 serial clock .............................................................. 157 serial data in ........................................................... 157 serial data out ........................................................ 157 slave mode .............................................................. 163 slave select ............................................................. 157 slave select synchronization .................................. 163 sleep operation ....................................................... 165 spi clock ................................................................. 162 typical connection .................................................. 161 ss .................................................................................... 157 sspov ............................................................................ 187 sspov status flag ......................................................... 187 sspstat register r/w bit ............................................................ 170, 171 stack full/underflow resets .............................................. 68 status register .................................................................. 80 subfsr .......................................................................... 341 subfwb ......................................................................... 330 sublw ............................................................................ 331 subulnk ........................................................................ 341 subwf ............................................................................ 331 subwfb ......................................................................... 332 swapf ............................................................................ 332 t table pointer operations (table) ........................................ 88 table reads ...................................................................... 68 tblrd ............................................................................. 333 tblwt ............................................................................. 334 time-out in various situations (table) ................................ 55 timer0 .............................................................................. 131 16-bit mode timer reads and writes ....................................................... 132 associated registers ............................................... 133 clock source edge select (t0se bit) ........................................................ 132 clock source select (t0cs bit) ............................... 132 operation ................................................................. 132 overflow interrupt .................................................... 133 prescaler. see prescaler, timer0.
? 2004 microchip technology inc. preliminary ds39629b-page 405 PIC18F6390/6490/8390/8490 timer1 .............................................................................. 135 16-bit read/write mode ........................................... 137 associated registers ............................................... 139 interrupt .................................................................... 138 operation ................................................................. 136 oscillator .......................................................... 135, 137 layout considerations ..................................... 138 overflow interrupt .................................................... 135 resetting, using a special event trigger output (ccp) ....................................... 138 tmr1h register ...................................................... 135 tmr1l register ....................................................... 135 use as a real-time clock ....................................... 138 timer2 .............................................................................. 141 associated registers ............................................... 142 interrupt .................................................................... 142 operation ................................................................. 141 output ...................................................................... 142 pr2 register ............................................................ 153 tmr2 to pr2 match interrupt .................................. 153 timer3 .............................................................................. 143 16-bit read/write mode ........................................... 145 associated registers ............................................... 145 operation ................................................................. 144 oscillator .......................................................... 143, 145 overflow interrupt ............................................ 143, 145 special event trigger (ccp) .................................... 145 tmr3h register ...................................................... 143 tmr3l register ....................................................... 143 timing diagrams a/d conversion ........................................................ 386 acknowledge sequence .......................................... 190 asynchronous reception ................................. 209, 225 asynchronous transmission ............................ 207, 223 asynchronous transmission (back to back) ......................................... 207, 223 automatic baud rate calculation ............................ 205 auto-wake-up bit (wue) during normal operation ............................................ 210 auto-wake-up bit (wue) during sleep ................... 210 baud rate generator with clock arbitration ............ 184 brg overflow sequence ......................................... 205 brg reset due to sda arbitration during start condition ..................................... 193 brown-out reset (bor) ........................................... 373 bus collision during a repeated start condition (case 1) ........................................... 194 bus collision during a repeated start condition (case 2) ........................................... 194 bus collision during a start condition (scl = 0) ......................................... 193 bus collision during a start condition (sda only) ...................................... 192 bus collision during a stop condition (case 1) ........................................... 195 bus collision during a stop condition (case 2) ........................................... 195 bus collision for transmit and acknowledge ........... 191 capture/compare/pwm (all ccp modules) ............ 375 clko and i/o .......................................................... 372 clock synchronization ............................................. 177 clock/instruction cycle .............................................. 69 example spi master mode (cke = 0) ..................... 376 example spi master mode (cke = 1) ..................... 377 example spi slave mode (cke = 0) ....................... 378 example spi slave mode (cke = 1) ....................... 379 external clock (all modes except pll) ................... 370 fail-safe clock monitor ........................................... 291 high/low-voltage detect characteristics ................ 367 high-voltage detect operation (vdirmag = 1) ..... 254 i 2 c bus data ............................................................ 380 i 2 c bus start/stop bits ............................................ 380 i 2 c master mode (7 or 10-bit transmission) ........... 188 i 2 c master mode (7-bit reception) ......................... 189 i 2 c master mode first start bit ................................ 185 i 2 c slave mode (10-bit recepti on, sen = 0) .......... 174 i 2 c slave mode (10-bit recepti on, sen = 1) .......... 179 i 2 c slave mode (10-bit transmission) .................... 175 i 2 c slave mode (7-bit reception, sen = 0) ............ 172 i 2 c slave mode (7-bit reception, sen = 1) ............ 178 i 2 c slave mode (7-bit transmission) ...................... 173 i 2 c slave mode general call address sequence (7 or 10-bit addr ess mode) ............ 180 i 2 c stop condition receive or transmit mode ................................................. 190 lcd interrupt timing in quarter-duty cycle drive ...................................................... 276 lcd sleep entry/exit when slpen = 1 or cs1:cs0 = 00 ............................................. 277 low-voltage detect operation (vdirmag = 0) ............................................... 253 master ssp i 2 c bus data ....................................... 382 master ssp i 2 c bus start/stop bits ........................ 382 pwm output ............................................................ 153 repeat start condition ............................................ 186 reset, watchdog timer (wdt), oscillator start-up timer (ost) and power-up timer (pwrt) ................................. 373 send break character sequence ............................ 211 slave synchronization ............................................. 163 slow rise time (mclr tied to v dd , v dd rise > t pwrt ) ............................................ 57 spi mode (master mode) ........................................ 162 spi mode (slave mode, cke = 0) ........................... 164 spi mode (slave mode, cke = 1) ........................... 164 synchronous reception (master mode, sren) ............................. 214, 228 synchronous transmission ............................. 212, 226 synchronous transmission (through txen) ...................................... 213, 227 time-out sequence on por w/pll enabled (mclr tied to v dd ) .......................................... 57 time-out sequence on power-up mclr not tied to v dd , case 1 ......................... 56 mclr not tied to v dd , case 2 ......................... 56 mclr tied to v dd , v dd rise < t pwrt ............. 56 timer0 and timer1 external clock .......................... 374 transition for entry to pri_idle mode ..................... 46 transition for entry to sec_run mode .................... 43 transition for entry to sleep mode ............................ 45 transition for two-speed start-up (intosc to hspll) ........................................ 289 transition for wake from idle to run mode ............... 46 transition for wake from sleep (hspll) .................. 45 transition from rc_run mode to pri_run mode ................................................. 44 transition from sec_run mode to pri_run mode (hspll) .................................. 43 transition to rc_run mode ..................................... 44 type-a in 1/2 mux, 1/2 bias drive ........................... 266
PIC18F6390/6490/8390/8490 ds39629b-page 406 preliminary ? 2004 microchip technology inc. type-a in 1/2 mux, 1/3 bias drive ........................... 268 type-a in 1/3 mux, 1/2 bias drive ........................... 270 type-a in 1/3 mux, 1/3 bias drive ........................... 272 type-a in 1/4 mux, 1/3 bias drive ........................... 274 type-a/type-b in static drive .................................. 265 type-b in 1/2 mux, 1/2 bias drive ........................... 267 type-b in 1/2 mux, 1/3 bias drive ........................... 269 type-b in 1/3 mux, 1/2 bias drive ........................... 271 type-b in 1/3 mux, 1/3 bias drive ........................... 273 type-b in 1/4 mux, 1/3 bias drive ........................... 275 usart synchronous receive (master/slave) .................................................. 384 usart synchronous transmission (master/slave) .................................................. 384 timing diagrams and specifications ac characteristics - internal rc accuracy .............. 371 capture/compare/pwm requirements (all ccp modules) ........................................... 375 clko and i/o requirements ................................... 372 example spi mode requirements (master mode, cke = 0) .................................. 376 example spi mode requirements (master mode, cke = 1) .................................. 377 example spi mode requirements (slave mode, cke = 0) .................................... 378 example spi slave mode requirements (cke = 1) .................................. 379 external clock requirements .................................. 370 i 2 c bus data requirements (slave mode) .................................................... 381 i 2 c bus start/stop bits requirements (slave mode) .................................................... 380 master ssp i 2 c bus data requirements ................ 383 master ssp i 2 c bus start/stop bits requirements ................................................... 382 pll clock ................................................................. 371 reset, watchdog timer, oscillator start-up timer, power-up timer and brown-out reset requirements ...................... 373 timer0 and timer1 external clock requirements ........................................ 374 usart synchronous receive requirements ......... 384 usart synchronous transmission requirements .................................................. 384 top-of-stack access .......................................................... 66 tstfsz ........................................................................... 335 two-speed start-up ................................................. 281, 289 two-word instructions example cases .......................................................... 70 txsta1 register brgh bit ................................................................. 201 txsta2 register brgh bit ................................................................. 220 v voltage reference specifications .................................... 366 w watchdog timer (wdt) ........................................... 281, 287 associated registers ............................................... 288 control register ....................................................... 287 during oscillator failure .......................................... 290 programming considerations .................................. 287 wcol ...................................................... 185, 186, 187, 190 wcol status flag ................................... 185, 186, 187, 190 www, on-line support ................... ................................... 5 x xorlw ............................................................................ 335 xorwf ........................................................................... 336
? 2004 microchip technology inc. preliminary ds39629b-page 407 PIC18F6390/6490/8390/8490 on-line support microchip provides on-line support on the microchip world wide web site. the web site is used by microchip as a means to make files and information easily available to customers. to view the site, the user must have access to the internet and a web browser, such as netscape ? or microsoft ? internet explorer. files are also available for ftp download from our ftp site. connecting to the microchip internet web site the microchip web site is available at the following url: www.microchip.com the file transfer site is available by using an ftp service to connect to: ftp://ftp.microchip.com the web site and file transfer site provide a variety of services. users may download files for the latest development tools, data sheets, application notes, user?s guides, articles and sample programs. a vari- ety of microchip specific business information is also available, including listings of microchip sales offices, distributors and factory representatives. other data available for consideration is: latest microchip press releases technical support section with frequently asked questions design tips device errata job postings microchip consultant program member listing links to other useful web sites related to microchip products conferences for products, development systems, technical information and more listing of seminars and events systems information and upgrade hot line the systems information and upgrade line provides system users a listing of the latest versions of all of microchip?s development systems software products. plus, this line provides information on how customers can receive the most current upgrade kits.the hot line numbers are: 1-800-755-2345 for u.s. and most of canada and 1-480-792-7302 for the rest of the world. 042003
PIC18F6390/6490/8390/8490 ds39629b-page 408 preliminary ? 2004 microchip technology inc. reader response it is our intention to provide you with the best documentation possible to ensure successful use of your microchip prod- uct. if you wish to provide your comments on organization, clarity, subject matter and ways in which our documentation can better serve you, please fax your comments to the technical publications manager at (480) 792-4150. please list the following information and use this outline to provide us with your comments about this document. to : technical publications manager re: reader response total pages sent ________ from: name company address city / state / zip / country telephone: (_______) _________ - _________ application (optional): would you like a reply? y n device: literature number: questions: fax: (______) _________ - _________ ds39629b PIC18F6390/6490/8390/8490 1. what are the best features of this document? 2. how does this document meet your hardware and software development needs? 3. do you find the organization of this document easy to follow? if not, why? 4. what additions to the document do you think would enhance the structure and subject? 5. what deletions from the document could be made without affecting the overall usefulness? 6. is there any incorrect or misleading information (what and where)? 7. how would you improve this document?
? 2004 microchip technology inc. preliminary ds39629b-page 409 PIC18F6390/6490/8390/8490 PIC18F6390/6490/8390/8490 product identification system to order or obtain information, e. g., on pricing or delivery, refer to the factory or the listed sales office . part no. x /xx xxx pattern package temperature range device device PIC18F6390/6490/8390/8490 (1) , PIC18F6390/6490/8390/8490t (2) ; v dd range 4.2v to 5.5v pic18lf6390/6490/8390/8490 (1) , pic18lf6390/6490/8390/8490t (2) ; v dd range 2.0v to 5.5v temperature range i = -40 c to +85 c (industrial) e= -40 c to +125 c (extended) package pt = tqfp (thin quad flatpack) pattern qtp, sqtp, code or special requirements (blank otherwise) examples: a) pic18lf6490-i/pt 301 = industrial temp., tqfp package, extended v dd limits, qtp pattern #301. b) pic18f8490-i/pt = industrial temp., tqfp package, normal v dd limits. c) pic18f8490-e/pt = extended temp., tqfp package, normal v dd limits. note 1: f = standard voltage range lf = wide voltage range 2: t = in tape and reel
ds39629b-page 410 preliminary ? 2004 microchip technology inc. americas corporate office 2355 west chandler blvd. chandler, az 85224-6199 tel: 480-792-7200 fax: 480-792-7277 technical support: 480-792-7627 web address: www.microchip.com atlanta alpharetta, ga 30022 tel: 770-640-0034 fax: 770-640-0307 boston westford, ma 01886 tel: 978-692-3848 fax: 978-692-3821 chicago itasca, il 60143 tel: 630-285-0071 fax: 630-285-0075 dallas addison plaza addison, tx 75001 tel: 972-818-7423 fax: 972-818-2924 detroit tri-atria office building farmington hills, mi 48334 tel: 248-538-2250 fax: 248-538-2260 kokomo kokomo, in 46902 tel: 765-864-8360 fax: 765-864-8387 los angeles mission viejo, ca 92691 tel: 949-462-9523 fax: 949-462-9608 san jose mountain view, ca 94043 tel: 650-215-1444 fax: 650-961-0286 toronto mississauga, ontario l4v 1x5, canada tel: 905-673-0699 fax: 905-673-6509 asia/pacific australia microchip technology australia pty ltd sydney, australia tel: 61-2-9868-6733 fax: 61-2-9868-6755 china - beijing wan tai bei hai bldg. beijing, 100027, china tel: 86-10-85282100 fax: 86-10-85282104 china - chengdu ming xing financial tower chengdu 610016, china tel: 86-28-86766200 fax: 86-28-86766599 china - fuzhou world trade plaza fuzhou 350001, china tel: 86-591-7503506 fax: 86-591-7503521 china - hong kong sar metroplaza kwai fong, n.t., hong kong tel: 852-2401-1200 fax: 852-2401-3431 china - shanghai far east international plaza shanghai, 200051 tel: 86-21-6275-5700 fax: 86-21-6275-5060 china - shenzhen united plaza shenzhen 518033, china tel: 86-755-82901380 fax: 86-755-8295-1393 china - shunde foshan city, guangdong 528303, china tel: 86-757-28395507 fax: 86-757-28395571 china - qingdao fullhope plaza, qingdao 266071, china tel: 86-532-5027355 fax: 86-532-5027205 india divyasree chambers bangalore, 560 025, india tel: 91-80-22290061 fax: 91-80-22290062 india international trade tower new delhi, 110019, india tel: +91-11-5160-8632 fax: +91-11-5160-8632 japan yokohama, kanagawa, 222-0033, japan tel: 81-45-471- 6166 fax: 81-45-471-6122 korea samsung-dong, kangnam-ku seoul, korea 135-882 tel: 82-2-554-7200 fax: 82-2-558-5932 or 82-2-558-5934 singapore singapore, 188980 tel: 65-6334-8870 fax: 65-6334-8850 taiwan kaohsiung branch kaohsiung 806, taiwan tel: 886-7-536-4816 fax: 886-7-536-4817 taiwan taiwan branch taipei city, 104, taiwan tel: 886-2-2500-6610 fax: 886-2-2508-0102 taiwan taiwan branch hsinchu city 300, taiwan tel: 886-3-572-9526 fax: 886-3-572-6459 europe austria austria tel: 43-7242-2244-399 fax: 43-7242-2244-393 denmark regus business centre ballerup dk-2750 denmark tel: 45-4420-9895 fax: 45-4420-9910 france 91300 massy, france tel: 33-1-69-53-63-20 fax: 33-1-69-30-90-79 germany d-85737 ismaning, germany tel: 49-89-627-144-0 fax: 49-89-627-144-44 italy milan, italy tel: 39-0331-742611 fax: 39-0331-466781 netherlands nl-5152 jr, drunen, netherlands tel: 31-416-690399 fax: 31-416-690340 united kingdom wokingham berkshire, england rg41 5tu tel: 44-118-921-5869 fax: 44-118-921-5820 08/16/04 w orldwide s ales and s ervice

▲Up To Search▲

Price & Availability of PIC18F6390

	To Download PIC18F6390 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .